Quality improvement of GaInNAs/GaAs quantum wells grown by plasma-assisted molecular beam epitaxy

The optimum growth condition of GaInNAs/GaAs quantum wells (QWs) by plasma-assisted molecular beam epitaxy was investigated. High-resolution X-ray diffraction and photoluminescence (PL) measurements showed that ion damage drastically degraded the quality of GaNAs and GaInNAs QWs and that ion removal magnets can effectively remove the excess ion damage. Remarkable improvement of PL intensity and obvious appearance of pendellosung fringes were observed by removing the N ions produced in the plasma cell. When the growth rate increased from 0.73 to 1.2 ML/s, the optimum growth temperature was raised from 460 degreesC to 480 degreesC and PL peak intensity increased two times. Although the N composition decreased with increasing growth rate, degradation of optical properties of GaInNAs QWs was observed when the growth rate was over 0.92 ML/s. Due to low-temperature growth of GaInNAs QWs, a distinctive reflection high-energy electron diffraction pattern was observed only when the GaAs barrier was grown under lower As-4 pressure. The samples with GaAs barriers grown under lower As-4 pressure (V/III ratio about 24) exhibited seven times increase in PL peak intensity compared with those grown under higher As-4 pressure (V/III ratio about 50). (C) 2001 Elsevier Science B,V. All rights reserved.

Low-timing-jitter, stretched-pulse passively mode-locked fiber laser with tunable repetition rate and high operation stability

We design a low-timing-jitter, repetition-rate-tunable, stretched-pulse passively mode-locked fiber laser by using a nonlinear amplifying loop mirror (NALM), a semiconductor saturable absorber mirror (SESAM), and a tunable optical delay line in the laser configuration. Low-timing-jitter optical pulses are stably produced when a SESAM and a 0.16 m dispersion compensation fiber are employed in the laser cavity. By inserting a tunable optical delay line between NALM and SESAM, the variable repetition-rate operation of a self-starting, passively mode-locked fiber laser is successfully demonstrated over a range from 49.65 to 50.47 MHz. The experimental results show that the newly designed fiber laser can maintain the mode locking at the pumping power of 160 mW to stably generate periodic optical pulses with width less than 170 fs and timing jitter lower than 75 fs in the 1.55 mu m wavelength region, when the fundamental repetition rate of the laser is continuously tuned between 49.65 and 50.47 MHz. Moreover, this fiber laser has a feature of turn-key operation with high repeatability of its fundamental repetition rate in practice.

Characterization of porous silicon nitride/silicon oxynitride composite ceramics produced by sol infiltration

Porous silicon nitride/silicon oxynitride composite ceramics were fabricated by silica sol infiltration of aqueous gelcasting prefabricated Si3N4 green compact. Silica was introduced by infiltration to increase the green density of specimens, so suitable properties with low shrinkage of ceramics were achieved during sintering at low temperature. Si2N2O was formed through reaction between Si3N4 and silica sol at a temperature above 1550 degrees C. Si3N4/Si2N2O composite ceramics with a low linear shrinkage of 1.3-5.7%, a superior strength of 95-180 MPa and a moderate dielectric constant of 4.0-5.0 (at 21-39 GHz) were obtained by varying infiltration cycle and sintering temperature. (C) 2010 Published by Elsevier B.V.

Deformation behaviour of electrodeposited nanocrystalline Ni with broad grain size distribution

In the present work, nanocrystalline Ni (nc-Ni) with a broad grain size distribution (BGSD) of 5-120 nm and an average grain size of 27.2 nm was prepared. The BGSD nc-Ni sample shows a similar strength and good ductility in comparison with electrodeposited nc-Ni with a narrow grain size distribution. The intracrystalline dislocation network was observed in the post-deformed microstructure confirming the conventional intracrystalline dislocation sliding mechanism in BGSD nc-Ni. The uniaxial tensile loading-unloading-loading deformation shows BGSD nc-Ni has the capability to store dislocations in the grain interior, which is very limited compared with that of coarse grained metals. For BGSD nc-Ni, the strain rate sensitivity of flow stress m enhances with decreasing strain rate. At the strain rate of 5 x 10(-6) s(-1), m was estimated to be 0.055. At the corresponding strain rate, the enhanced ductility along with the decreased strength was achievable, indicating activation of other deformation mechanisms, e. g. grain boundary sliding or diffusion.

流体力学半径对估算胶体微球聚集速率常数的影响

胶体粒子聚集速率常数实验值远低于理论值一直是被普遍关注的问题.聚集速率常数的理论推导是基于粒子的几何半径来考虑的,但决定粒子扩散速率及聚集速率的应该是粒子的流体力学半径(大于几何半径),因而它是使聚集速率常数实验值低于理论值的因素之一.影响流体力学半径的因素很多,其中,带电粒子在溶液中因表面存在双电层,会明显增大流体力学半径,造成聚集速率减慢.而双电层的厚度又随溶液中离子强度的不同而改变.本工作在聚集速率的公式中引入了修正因子,即几何半径与其流体力学半径之比,以修正由于用几何半径代替流体力学半径带来的误差.其中几何半径和流体力学半径可以分别用扫描电镜(SEM)和动态光散射(DLS)来测定.以两种粒径的聚苯乙烯带电微球为例,考察了在不同离子强度下,该误差的大小.结果发现,对于半径为30 nm的微球,用流体力学半径计算的慢聚集速率常数比理论值偏低约8%.该误差随离子强度增加而减少.对于快聚集情况,流体力学半径对聚集速率基本没有影响.

微生物法沥取重金属污泥中铬的研究

本文研究了两种微生物及其组合沥取、回收用微生物法治理电镀铬废水产生的铬污泥中的铬。铬污泥富含C、N、O，含铬量为13%， 经X-光电子能谱分析铬以三价态(氢氧化铬)存在。二种微生物分别从一酸性矿水和酸性污泥中分离筛选得到，经鉴定为硫杆菌属 (Thiobacillus Beijerinek)的两个不同种，一为氧化亚铁硫杆菌(Thiobacillu ferrooxidans, TF), 另一为氧化硫硫杆菌 (Thiobacillus thiooxidans, TT)。研究并比较了不同微生物对污泥中铬的沥取能力，结果表明，TT菌沥取铬效率最高。振荡、动 态淋滤、静置等沥取方式经过研究表明动态淋滤为最佳，室温条件下(15-20℃)，污泥浓度为20g/L时，总铬沥出率达60%时所需时 间：动态淋滤为48.5h，振荡和静置方式分别为91.22，81.6h。研究了不同温度、不同起始PH、不同污泥浓度及非成熟菌液对微生 物沥取能力的影响：(1) 沥取前期，温度对铬的沥出影响较大；微生物沥取反应基本属一级反应；温度与反应速率的关系基本符合 Arrhenius方程，但沥取后期这一特点并不突出。(2) 沥取液最适起始PH为菌液自然PH；PH值的人为改变将使铬的沥出大大降低。 (3) 污泥浓度与铬的沥出呈正相关，但浓度高于30g/L时，铬的沥出量不再增加。(4) 非成熟菌液沥出铬的能力较差，但沥取液中 微生物生长繁殖较为活跃。总结微生物沥取反应最佳沥取条件为：TT成熟菌液、污泥浓度10g/L、温度25-36℃、动态淋滤方式，此 时铬几乎可100%从污泥中沥出。经扫描电镜分析，沥取开始时，微生物紧密吸附于污泥颗粒表面上，表面紧密吸附为微生物发挥功 能提供了基础。微生物沥取污泥中铬的反应机理推测为：硫细菌代谢产硫酸或氧化Fe2+成Fe3+，利用酸，Fe3+ 及自身氧化酶系统 氧化污泥中Cr3+为Cr6+,Cr6+溶出结晶为CrO3。This paper has studied bioleaching and recovery of Chronium(Cr)from electroplating sludge by two consortum of bacteria and their combination, with sludge produced by microbiological process treating electroplating wastewater containing Cr as material. The share of Cr is 13% and its state is Cr (OH)3 in the sludge. One of the bacteria in the paper was isolated from acid sewage sludge and the other was from acid mineral water. The former was tested and determined as Thiobacillus ferroxidans(TF) and the latter was Thiobacillus thiooxidans(TT). Different microorganisms, responsible for the metal leaching activity, have great influence on the efficiency of leaching. The results showed that TT has biggest power. Experiments were conducted to examined effects of three different ways of leaching(Shaking, Down-leaching, Static-leaching). When temperature was in-door's (15-20℃)and concentration of the sludge was 20g/L, the bioleaching time required to reach 60% of Cr solubilization with the above three ways were 91.2, 48.5, 81.6h respectively. Down-leaching was proved to be the most efficient. The influence of different temperature, initial PH, concentration of the sludge and non-mature inoculum had been studied. The results obtained reveal that: (1) The variation of temperature is important during the time from initial to middle of leaching. The reaction of bioleaching belongs to first-order. The relation between the bioleaching rate constant(In k)and temerature can be expressed by Arrhenius function. (2) The fittest initial PH is the nature PH of mature inoculum. Any alteration with it could cause clearly negative effection. (3) The concentration of the sludge can make strong influence on the bioleaching efficiency. But when the concentration is above 30g/L, the increasing of Cr in the solution is little. (4) If non-mature inoculum acts as the bioleachin microorganism, little quantity of Cr would be gained from the sludge. But the micormass in the solution is very active. The results from electron microscope showed that microorganisms adhered to the surface of the sludge and the adherence was the first stage of the bioleaching. Some salts of Cr can be obtained afer the water of the bioleaching solution being evaporated. By analysing the results of experiment with X-Ray spectroscopy, the salt was identified as CrO3. The recovery rate of Cr is 78.4%.

Preformation of clusters in heavy nuclei and cluster radioactivity

Within the preformed cluster model approach, the values of the preformation factors have been deduced from the experimental cluster decay half-lives assuming that the decay constant of the heavy-ion emission is the product of the assault frequency, the preformation factor and the penetrability. The law according to which the preformation factors follow a simple dependence on the mass of the cluster was confirmed. Then predictions for some of the most possible cluster decays are provided.

Dissociative recombination of the acetaldehyde cation, CH3CHO+

The dissociative recombination of the acetaldehyde cation, CH3CHO+, has been investigated at the heavy ion storage ring CRYRING at the Manne Siegbahn Laboratory in Stockholm, Sweden. The dependence of the absolute cross section of the reaction on the relative kinetic energy has been determined and a thermal rate coefficient of k(T) = (1.5 +/- 0.2) x 10(-6) (T/300)(-0.70 +/- 0.02) cm(3) s(-1) has been deduced, which is valid for electron temperatures between similar to 10 and 1000 K. The branching fractions of the reaction were studied at similar to 0 eV relative kinetic energy and we found that breaking one of the bonds between two of the heavy atoms occurs in 72 +/- 2% of the reactions. In the remaining events the three heavy atoms stay in the same product fragment. While the branching fractions are fairly similar to the results from an earlier investigation into the dissociative recombination of the fully deuterated acetaldehyde cation, CD3CDO+, the thermal rate coefficient is somewhat larger for CH3CHO+. Astrochemical implications of the results are discussed.

Evaluation of the interaction between netropsin and double stranded DNA by capillary zone electrophoresis

Capillary zone electrophoresis (CZE) was applied to study the interaction between netropsin and a 14mer double stranded DNA (dsDNA). The binding constant of this interaction calculated from Scatchard plot was (1.07+/-0.10) X 10(5) (mol/L)(-1). The binding stoichiometry was 1:1. The use of polyacrylamide coated capillary showed better effect in the analysis of DNA than noncoated capillary.

Decay dynamics of excited CS2 and NH3 investigated by femtosecond laser

By using the home-made femtosecond laser system and the time-of-flight mass spectrometer, the decay dynamics of excited carbon disulfide (CS2) and ammonia (NH3) are investigated in real time by pump-probe multiphoton ionization detection. The estimated lifetime constant of the NH3 (A) over tilde (1)A(2)' state (51+/-4 fs) agreed quite well with the literature report. For the first time, the decay lifetime constants of the NH3 (E) over tilde'(1)A(1)' state (937+/-93 fs), the CS2 (a) over tilde (3)A(2) state (153+/-10 fs), and the CS2 Rydberg state [(3)/(2)]6ssigma(g) ((3)Pi(g)) (948+/-23 fs) are obtained.

Quantitative evaluation of the interaction between pUC19DNA and ovalbumin by capillary zone electrophoresis

Capillary zone electrophoresis (CZE) was used to study the interaction between pUC19DNA (pUC19) and ovalbumin (Ova). Samples containing pUC19 and Ova at various ratios were incubated at room temperature and were then separated by CZE with tris-acetate buffer at pH 7.2. Reduction in ultraviolet (UV) absorbance of pUC19 was due to the decrease of free pUC19 after binding to Ova. The binding constant of the interaction calculated from the Scatchard plot was (1.46+/-0.15) x 10(5) M-1. The use of polyacrylamide-coated capillary showed better effects than that of uncoated capillary. The results show that it is important to keep a constant ionic strength in the samples in order to obtain accurate quantitative data in binding assays by CZE.

Synthesis and characterization of (Zn,Cd)TiO3 by a modified sol-gel method

Ilmenite-type (Zn1-xCdx)TiO3 (0 <= x <= 0.15 and 0.8 <= x <= 1.0) was synthesized by a modified sol-gel route including the Pechini process via two-step heat treatments. The thermal stability of (Zn1-xCdx)TiO3 depended on the amount of cadmium content. The as-synthesized (Zn1-xCdx)TiO3 (0 <= x <= 0.15 and 0.8 <= x <= 1.0) showed higher thermal stability than that of ZnTiO3. The variation of the dielectric constant of all synthesized (Zn1-xCdx)TiO3 samples for all measurement frequencies showed a similar tendency.

Characterization of High Melt Strength Polypropylene Synthesized via Silane Grafting Initiated by In Situ Heat Induction Reaction

High melt strength polypropylene (HMSPP) was synthesized by in situ heat induction reaction, in which pure polypropylene (PP) powders without any additives were used as a basic resin and vinyl trimethoxysilane (VTMS) as a grafting and crosslinking agent. The grafting reaction of VTMS with PP was confirmed by FTIR. The structure and properties of HMSPP were characterized by means of various measurements. The content of grafted silane played a key role on the melt strength and melt flow rate (MFR) of HMSPP. With increasing the content of grafted silane, the melt strength of HMSPP increased, and the MFR reduced. In addition, due to the existence of cross-linking structure, the thermal stability and tensile strength of HMSPP were improved compared with PP.

Crystallographic and electrochemical characteristics of TiZrNiCu quasicrystal ball-milled with La0.9Zr0.1Ni4.5Al0.5 alloy

Icosahedral quasicrystalline Ti45Zr35Ni17Cu3 alloy was ball-milled with 30 mass% La0.9Zr0.1Ni4.5Al0.5 alloy (LaNi5 phase), the effect of the milling time on crystallographic and electrochemical characteristics of the alloy powder was investigated. The amount of amorphous phase increased with increasing milling time from 60 to 360 min, and the LaNi5 phase cannot be observed when milling time was 240 min or more. The maximum discharge capacity and high-rate dischargeability of milled alloy electrodes were obviously higher than those of the alloy electrode before milling. The cycling capacity retention rate after 40 cycles increased from 52.8% (t = 60 min) to 62.9% (t = 360 min).

Colloidal photonic crystals with a graded lattice-constant distribution

In this work, a gradient polystyrene colloidal photonic crystal was fabricated by annealing in a graded temperature field. The lattice constant of the gradient crystal gradually varied along the temperature-gradient direction. The positional bandgap wavelength as well as the attenuation of the bandgap wavelength could be tuned dependent on the position of the gradient colloidal crystal along the gradient direction because of the lattice-constant variation.