Intravenous regional block is similar to sympathetic ganglion block for pain management in patients with complex regional pain syndrome type I

Sympathetic ganglion block (SGB) or intravenous regional block (IVRB) has been recommended for pain management in patients with complex regional pain syndrome type I (CRPS-I). Forty-five patients were initially selected but only 43 were accepted for the study. The present study evaluated the efficacy of IVRB produced by combining 70 mg lidocaine with 30 µg clonidine (14 patients, 1 male/13 females, age range: 27-50 years) versus SGB produced by the injection of 70 mg lidocaine alone (14 patients, 1 male/13 females, age range: 27-54 years) or combined with 30 µg clonidine (15 patients, 1 male/14 females, age range: 25-50 years) into the stellate ganglion for pain management in patients with upper extremity CRPS-I. Each procedure was repeated five times at 7-day intervals, and pain intensity and duration were measured using a visual analog scale immediately before each procedure. A progressive and significant reduction in pain scores and a significant increase in the duration of analgesia were observed in all groups following the first three blocks, but no further improvement was obtained following the last two blocks. Drowsiness, the most frequent side effect, and dry mouth occurred only in patients submitted to SGB with lidocaine combined with clonidine. The three methods were similar regarding changes in pain intensity and duration of analgesia. However, IVRB seems to be preferable to SGB due to its easier execution and lower risk of undesirable effects.

Influence of cueing on the preparation and execution of untrained and trained complex motor responses

This study investigated the influence of cueing on the performance of untrained and trained complex motor responses. Healthy adults responded to a visual target by performing four sequential movements (complex response) or a single movement (simple response) of their middle finger. A visual cue preceded the target by an interval of 300, 1000, or 2000 ms. In Experiment 1, the complex and simple responses were not previously trained. During the testing session, the complex response pattern varied on a trial-by-trial basis following the indication provided by the visual cue. In Experiment 2, the complex response and the simple response were extensively trained beforehand. During the testing session, the trained complex response pattern was performed in all trials. The latency of the untrained and trained complex responses decreased from the short to the medium and long cue-target intervals. The latency of the complex response was longer than that of the simple response, except in the case of the trained responses and the long cue-target interval. These results suggest that the preparation of untrained complex responses cannot be completed in advance, this being possible, however, for trained complex responses when enough time is available. The duration of the 1st submovement, 1st pause and 2nd submovement of the untrained and the trained complex responses increased from the short to the long cue-target interval, suggesting that there is an increase of online programming of the response possibly related to the degree of certainty about the moment of target appearance.

Emergence of clonal complex 5 (CC5) methicillin-resistant Staphylococcus aureus (MRSA) isolates susceptible to trimethoprim-sulfamethoxazole in a Brazilian hospital

In this study, genotyping techniques including staphylococcal chromosomal cassette mec (SCCmec) typing, pulsed-field gel electrophoresis (PFGE), multilocus sequence typing (MLST) and restriction-modification tests were used to compare the molecular characteristics of methicillin-resistant Staphylococcus aureus (MRSA) isolates recovered at two times within a 10-year interval (1998 and 2008) from a tertiary Brazilian hospital. In addition, the antimicrobial susceptibility profiles were analyzed. All 48 MRSA isolates from 1998 and 85.7% from 2008 (48/56 isolates) displayed multidrug-resistance phenotypes and SCCmec III. All but one of the 13 representative SCCmec III isolates belonged to CC8 and had PFGE patterns similar to that of the BMB9393 strain (Brazilian epidemic clone of MRSA; BEC). In 2008, we found an increased susceptibility to rifampicin and chloramphenicol among the SCCmec III isolates. In addition, we detected the entrance of diverse international MRSA lineages susceptible to trimethoprim-sulfamethoxazole (SXT), almost all belonging to CC5. These non-SCCmec III isolates were related to the USA 300 (ST8-SCCmec IV; PFGE-type B), USA 800 (ST5-SCCmec IV; subtype D1), USA 100 (ST5-SCCmec II; subtype D2), and EMRSA-3/Cordobes (ST5-SCCmec I, type C) clones. To the best of our knowledge, this is the first report of the emergence of isolates genetically related to the EMRSA-3/Cordobes clone in southeast Brazil. In this regard, these isolates were the most common non-SCCmec III MRSA in our institution, accounting for 8.9% of all isolates recovered in 2008. Thus, despite the supremacy of BEC isolates in our country, significant changes may occur in local MRSA epidemiology, with possible consequences for the rationality of MRSA empiric therapy.

Effect of selective β-adrenoceptor blockade and surgical resection of the celiac-superior mesenteric ganglion complex on delayed liquid gastric emptying induced by dipyrone, 4-aminoantipyrine, and antipyrine in rats

There is evidence for participation of peripheral β-adrenoceptors in delayed liquid gastric emptying (GE) induced in rats by dipyrone (Dp), 4-aminoantipyrine (AA), and antipyrine (At). The present study aimed to determine whether β-adrenoceptors are involved in delayed GE induced by phenylpyrazole derivatives and the role of the prevertebral sympathetic nervous system in this condition. Male Wistar rats weighing 220-280 g were used in the study. In the first experiment rats were intravenously pretreated with vehicle (V), atenolol 30 mg/kg (ATE, β1-adrenergic antagonist), or butoxamine 25 mg/kg (BUT, β2-adrenergic antagonist). In the second experiment, rats were pretreated with V or SR59230A 2 mg/kg (SRA, β3-adrenergic antagonist). In the third experiment, rats were subjected to surgical resection of the celiac-superior mesenteric ganglion complex or to sham surgery. The groups were intravenously treated with saline (S), 240 µmol/kg Dp, AA, or At, 15 min after pretreatment with the antagonists or V and nine days after surgery. GE was determined 10 min later by measuring the percentage of gastric retention (%GR) of saline labeled with phenol red 10 min after gavage. The %GR (means±SE, n=6) values indicated that BUT abolished the effect of Dp (BUT+Dp vs V+Dp: 35.0%±5.1% vs 56.4%±2.7%) and At (BUT+At vs V+At: 33.5%±4.7% vs 52.9%±2.6%) on GE, and significantly reduced (P<0.05) the effect of AA (BUT+AA vs V+AA: 48.0%±5.0% vs 65.2%±3.8%). ATE, SRA, and sympathectomy did not modify the effects of treatments. These results suggest that β2-adrenoceptor activation occurred in delayed liquid gastric emptying induced by the phenylpyrazole derivatives dipyrone, 4-aminoantipyrine, and antipyrine. Additionally, the released neurotransmitter did not originate in the celiac-superior mesenteric ganglion complex.

Histidine-tryptophan-ketoglutarate solution decreases mortality and morbidity in high-risk patients with severe pulmonary arterial hypertension associated with complex congenital heart disease: an 11-year experience from a single institution

Cardioplegic reperfusion during a long term ischemic period interrupts cardiac surgery and also increases cellular edema due to repeated solution administration. We reviewed the clinical experiences on myocardial protection of a single perfusion with histidine-tryptophan-ketoglutarate (HTK) for high-risk patients with severe pulmonary arterial hypertension associated with complex congenital heart disease. This retrospective study included 101 high-risk patients undergoing arterial switch operation between March 2001 and July 2012. We divided the cohort into two groups: HTK group, myocardial protection was carried out with one single perfusion with HTK solution; and St group, myocardial protection with conventional St. Thomas' crystalloid cardioplegic solution. The duration of cardiopulmonary bypass did not differ between the two groups. The mortality, morbidity, ICU stay, post-operative hospitalization time, and number of transfusions in HTK group were lower than those in St group (P<0.05). Univariate and multivariate analysis showed that HTK is a statistically significant independent predictor of decreased early mortality and morbidity (P<0.05). In conclusion, HTK solution seems to be an effective and safe alternative to St. Thomas' solution for cardioplegic reperfusion in high-risk patients with complex congenital heart disease.

Scalable Feature Selection Applications for Genome-Wide Association Studies of Complex Diseases

Personalized medicine will revolutionize our capabilities to combat disease. Working toward this goal, a fundamental task is the deciphering of geneticvariants that are predictive of complex diseases. Modern studies, in the formof genome-wide association studies (GWAS) have afforded researchers with the opportunity to reveal new genotype-phenotype relationships through the extensive scanning of genetic variants. These studies typically contain over half a million genetic features for thousands of individuals. Examining this with methods other than univariate statistics is a challenging task requiring advanced algorithms that are scalable to the genome-wide level. In the future, next-generation sequencing studies (NGS) will contain an even larger number of common and rare variants. Machine learning-based feature selection algorithms have been shown to have the ability to effectively create predictive models for various genotype-phenotype relationships. This work explores the problem of selecting genetic variant subsets that are the most predictive of complex disease phenotypes through various feature selection methodologies, including filter, wrapper and embedded algorithms. The examined machine learning algorithms were demonstrated to not only be effective at predicting the disease phenotypes, but also doing so efficiently through the use of computational shortcuts. While much of the work was able to be run on high-end desktops, some work was further extended so that it could be implemented on parallel computers helping to assure that they will also scale to the NGS data sets. Further, these studies analyzed the relationships between various feature selection methods and demonstrated the need for careful testing when selecting an algorithm. It was shown that there is no universally optimal algorithm for variant selection in GWAS, but rather methodologies need to be selected based on the desired outcome, such as the number of features to be included in the prediction model. It was also demonstrated that without proper model validation, for example using nested cross-validation, the models can result in overly-optimistic prediction accuracies and decreased generalization ability. It is through the implementation and application of machine learning methods that one can extract predictive genotype–phenotype relationships and biological insights from genetic data sets.

Electric paralyzation and reduction of weight loss in the processing of round-cooked spiny lobsters

This study proposes alternatives to the current methods of processing round-cooked lobster. The paralyzation of lobsters with direct electric shock consumes 10.526 x 10-3 kWh, which is significantly less than the 11 kWh required by the traditional thermal-shock method (based on 60 kg of lobsters). A better weight gain was obtained by immersion of paralyzed lobsters in brine before cooking. Systematic trials combining 3, 6, or 9% brine concentrations with immersion periods of 15, 30, or 45 minutes were performed in order to determine the best combinations. A mathematical model was designed to predict the weight gain of lobsters of different sizes in any combination of treatments. For small lobsters, a 45 minutes immersion in 6% brine gave the best response in terms of weight gain (4.7%) and cooking produced a weight loss of only 1.34% in relation to fresh lobster weight. For medium-sized lobsters, a 45 minutes immersion in 9% brine produced a weight gain of 2.64%, and cooking a weight gain of 1.08%. For large lobsters, a 45 minutes immersion in 6% brine produced a weight gain of 3.87%, and cooking a weight gain of 1.62%.

Affektitehdas. Työn rationalisoinnin historiallisia jatkumoita

Affektit, kapitalismi ja työn rationalisointi yhdistyvät toisiinsa erottamattomasti. Nykykeskusteluissa työstä ja työelämästä rationalisointi jaetaan usein tekniseen fordistiseen rationalisointiin ja sitä tunteellisempaan postfordistiseen rationalisointiin. Tämä tutkimus osoittaa, affektiivisen rationalisoinnin käsitteen kautta, että työn vanhat ja uudet tieteet asettuvat jatkumoon. Työn tieteissä tietoa työläisestä tuotetaan asettamalla ominaisuuksia aina uudelleen määriteltävään työläisen luokittuneeseen ja sukupuolittuneeseen affektiiviseen figuuriin. Tiedon tuottamisen näkökulmasta muun muassa tayloristiset työn tehostamisen fantasiat, ihmissuhdekoulukunnan ideologiat sekä uuden työn autonomiset järjestykset sisältävät yhtenäisiä piirteitä. Tutkimuksen pääkysymys on: miten affekteja rationalisoidaan työssä, työn tieteissä ja niiden kerrostumissa. Tutkimuksessa kysytään myös, miten affekti kiinnittää luokittuneet ja sukupuolittuneet subjektit työn rationalisoinnin aatteeseen ja millaisia mahdollisuuksia työläiseksi tulemiseen niissä tarjotaan. Kysymystä lähestytään monipuolisen aineiston ja lukuisten teemojen kautta. Aineistoina toimivat muun muassa rationalisoinnin klassikko-teokset, operaismo-vaikutteisen prekariaattiliikkeen pamfletit, ajatushautomoiden uuden työn visiot, self-help-teokset uranaisille sekä Helsingin Sanomien työelämäkeskustelut. Tutkimuksen monipuolista aineistoa lähiluetaan ja tulkitaan siihen luodun erityisen metodologian kautta, joka koostuu kolmesta osa-alueesta: historiallistaminen, paikantuminen ja figuurit. Kaksi ensimmäistä korostavat kontekstien ja position merkitystä tiedon tuotannossa, kolmas osoittaa tiedon tuottamisen valtasuhteita. Työn tieteiden visiot ideaalityöläisestä materialisoituvat figuurien kautta negaatioina kuvaten sitä, millainen ideaalityöläinen ei ole. Väitöskirja aineistoineen paikantuu Suomeen, mutta se osoittaa työn tieteiden ja affektiivisen rationalisoinnin globaaliutta sekä sidonnaisuutta Yhdysvaltoihin, sen yrityskulttuuriin ja esimerkiksi työtehotutkimuksiin Hawthornen elektroniikkatehtaalla vuosina 1924–1933. Väitöskirja tuo uusia näkökulmia nykykeskusteluun työstä, työläisistä, kapitalismista ja affekteista. Se osoittaa, että itsen tuntemisen ja kertomisen tieteitä, kuten psykologiaa, tarjotaan usein ratkaisuksi kapitalistisen tuotannon aiheuttamiin suuriin ja pieniin kurjuuksiin, vaikka terapeuttinen tunnekulttuuri itsessään on muodostunut osana rationalisoinnin ja kapitalismin ambivalentteja kehiä. Tutkimus myös muistuttaa, että työn järjestyksien keskiössä säilyy työläisen ja affektitehtaan konflikti silloinkin, kun fordistinen imperatiivi ”älä!” vaihtuu postfordistiseen kehotukseen ”tunne”.

Impacts of increased levels of wind penetration on the Electric Power System of the Åland Islands

The application of VSC-HVDC technology throughout the world has turned out to be an efficient solution regarding a large share of wind power in different power systems. This technology enhances the overall reliability of the grid by utilization of the active and reactive power control schemes which allows to maintain frequency and voltage on busbars of the end-consumers at the required level stated by the network operator. This master’s thesis is focused on the existing and planned wind farms as well as electric power system of the Åland Islands. The goal is to analyze the wind conditions of the islands and appropriately predict a possible production of the existing and planned wind farms with a help of WAsP software program. Further, to investigate the influence of increased wind power it is necessary to develop a simulation model of the electric grid and VSC-HVDC system in PSCAD and examine grid response to different wind power production cases with respect to the grid code requirements and ensure the stability of the power system.

Converter-Fed Induction Motor Losses: Determination With IEC Methods

Energy efficiency is an important topic when considering electric motor drives market. Although more efficient electric motor types are available, the induction motor remains as the most common industrial motor type. IEC methods for determining losses and efficiency of converter-fed induction motors were introduced recently with the release of technical specification IEC/TS 60034-2-3. Determining the induction motor losses with IEC/TS 60034-2-3 method 2-3-A and assessing the practical applicability of the method are the main interests of this study. The method 2-3-A introduces a specific test converter waveform to be used in the measurements. Differences between the induction motor losses with a test converter supply, and with a DTC converter supply are investigated. In the IEC methods, the tests are run at motor rated fundamental voltage, which, in practice, requires the frequency converter to be fed with a risen input voltage. In this study, the tests are run on both frequency converters with artificially risen converter input voltage, resulting in rated motor fundamental input voltage as required by IEC. For comparison, the tests are run with both converters on normal grid input voltage supply, which results in lower motor fundamental voltage and reduced flux level, but should be more relevant from practical point of view. According to IEC method 2-3-A, tests are run at rated motor load, and to ensure comparability of the results, the rated load is used in the grid-fed converter measurements, although motor is overloaded while producing the rated torque at reduced flux level. The IEC 2-3-A method requires also sinusoidal supply test results with IEC method 2-1-1B. Therefore, the induction motor losses with the recently updated IEC 60034-2-1 method 2-1-1B are determined at the motor rated voltage, but also at two lower motor voltages, which are according to the output fundamental voltages of the two network-supplied converters. The method 2-3-A was found to be complex to apply but the results were stable. According to the results, the method 2-3-A and the test converter supply are usable for comparing losses and efficiency of different induction motors at the operating point of rated voltage, rated frequency and rated load, but the measurements do not give any prediction of the motor losses at final application. One might therefore strongly criticize the method’s main principles. It seems, that the release of IEC 60034-2-3 as a technical specification instead of a final standard for now was justified, since the practical relevance of the main method is questionable.

Microparticles obtained by complex coacervation: influence of the type of reticulation and the drying process on the release of the core material

Microparticles obtained by complex coacervation were crosslinked with glutaraldehyde or with transglutaminase and dried using freeze drying or spray drying. Moist samples presented Encapsulation Efficiency (%EE) higher than 96%. The mean diameters ranged from 43.7 ± 3.4 to 96.4 ± 10.3 µm for moist samples, from 38.1 ± 5.36 to 65.2 ± 16.1 µm for dried samples, and from 62.5 ± 7.5 to 106.9 ± 26.1 µm for rehydrated microparticles. The integrity of the particles without crosslinking was maintained when freeze drying was used. After spray drying, only crosslinked samples were able to maintain the wall integrity. Microparticles had a round shape and in the case of dried samples rugged walls apparently without cracks were observed. Core distribution inside the particles was multinuclear and homogeneous and core release was evaluated using anhydrous ethanol. Moist particles crosslinked with glutaraldehyde at the concentration of 1.0 mM.g-1 protein (ptn), were more efficient with respect to the core retention compared to 0.1 mM.g-1 ptn or those crosslinked with transglutaminase (10 U.g-1 ptn). The drying processes had a strong influence on the core release profile reducing the amount released to all dry samples

Uncertainty of Efficiency Measurements in Electric Drives

The two central goals of this master's thesis are to serve as a guidebook on the determination of uncertainty in efficiency measurements and to investigate sources of uncertainty in efficiency measurements in the field of electric drives by a literature review, mathematical modeling and experimental means. The influence of individual sources of uncertainty on the total instrumental uncertainty is investigated with the help of mathematical models derived for a balance and a direct air cooled calorimeter. The losses of a frequency converter and an induction motor are measured with the input-output method and a balance calorimeter at 50 and 100 % loads. A software linking features of Matlab and Excel is created to process measurement data, calculate uncertainties and to calculate and visualize results. The uncertainties are combined with both the worst case and the realistic perturbation method and distributions of uncertainty by source are shown based on experimental results. A comparison of the calculated uncertainties suggests that the balance calorimeter determines losses more accurately than the input-output method with a relative RPM uncertainty of 1.46 % compared to 3.78 - 12.74 % respectively with 95 % level of confidence at the 93 % induction motor efficiency or higher. As some principles in uncertainty analysis are open to interpretation the views and decisions of the analyst can have noticeable influence on the uncertainty in the measurement result.

Studies of rotor dynamics using a multibody simulation approach

The non-idealities in a rotor-bearing system may cause undesirable subcritical superharmonic resonances that occur when the rotating speed of the rotor is a fraction of the natural frequency of the system. These resonances arise partly from the non-idealities of the bearings. This study introduces a novel simulation approach that can be used to study the superharmonic vibrations of rotor-bearing systems. The superharmonic vibrations of complex rotor-bearing systems can be studied in an accurate manner by combining a detailed rotor and bearing model in a multibody simulation approach. The research looks at the theoretical background of multibody formulations that can be used in the dynamic analysis of flexible rotors. The multibody formulations currently in use are suitable for linear deformation analysis only. However, nonlinear formulation may arise in high-speed rotor dynamics applications due to the cenrrifugal stiffening effect. For this reason, finite element formulations that can describe nonlinear deformation are also introduced in this work. The description of the elastic forces in the absolute nodal coordinate formulation is studied and improved. A ball bearing model that includes localized and distributed defects is developed in this study. This bearing model could be used in rotor dynamics or multibody code as an interface elements between the rotor and the supporting structure. The model includes descriptions of the nonlinear Hertzian contact deformation and the elastohydrodynamic fluid film. The simulation approaches and models developed here are applied in the analysis of two example rotor-bearing systems. The first example is an electric motor supported by two ball bearings and the second is a roller test rig that consists of the tube roll of a paper machine supported by a hard-bearing-type balanceing machine. The simulation results are compared to the results available in literature as well as to those obtained by measuring the existing structure. In both practical examples, the comparison shows that the simulation model is capable of predicting the realistic responses of a rotor system. The simulation approaches developed in this work can be used in the analysis of the superharmonic vibrations of general rotor-bearing systems.