Estudo de antenas patches de microfita miniaturizadas em banda larga para aplicação em dispositivos móveis e portáteis

This work presents techniques used to design and manufacture microstrip patch antennas for applications in portable and mobile devices. To do so, are evaluated several factors that can influence the performance of microstrip patch antennas. Miniaturization techniques are studied and employed in order to apply this type of antenna in mobile and / or mobile. The theories of microstrip patch antennas are addressed by analyzing characteristics such as constitution, kinds of patches, substrates, feeding methods, analysis methods, the main advantages and disadvantages and others. Techniques for obtaining broadband microstrip patch antennas were surveyed in literature and exemplified mainly by means of simulations and measurements. For simulations of the antennas was used the commercial software . In addition, antenna miniaturization techniques have been studied as a main concern the fundamental limits of antennas with special attention to electrically small antennas because they are directly linked to the microstrip patch antennas. Five design antennas are proposed to demonstrate the effectiveness of techniques used to obtain the microstrip patch antennas broadband and miniaturized for use in mobile devices and/or portable. For this, the proposed antennas were simulated, built and measured. The antennas are proposed to be used in modern systems of wireless communications such as DTV, GPS, IEEE 802.16, IEEE 802.11, etc. The simulations of the antennas were made in business and computer programs. The measured results were obtained with a parser Vector of networks of the Rhode and Schwarz model ZVB 14

Desacoplamento de um gerador síncrono através de um controle adaptativo por modelo de referência baseado em funções de Base radial

An alternative nonlinear technique for decoupling and control is presented. This technique is based on a RBF (Radial Basis Functions) neural network and it is applied to the synchronous generator model. The synchronous generator is a coupled system, in other words, a change at one input variable of the system, changes more than one output. The RBF network will perform the decoupling, separating the control of the following outputs variables: the load angle and flux linkage in the field winding. This technique does not require knowledge of the system parameters and, due the nature of radial basis functions, it shows itself stable to parametric uncertainties, disturbances and simpler when it is applied in control. The RBF decoupler is designed in this work for decouple a nonlinear MIMO system with two inputs and two outputs. The weights between hidden and output layer are modified online, using an adaptive law in real time. The adaptive law is developed by Lyapunov s Method. A decoupling adaptive controller uses the errors between system outputs and model outputs, and filtered outputs of the system to produce control signals. The RBF network forces each outputs of generator to behave like reference model. When the RBF approaches adequately control signals, the system decoupling is achieved. A mathematical proof and analysis are showed. Simulations are presented to show the performance and robustness of the RBF network

Controle inteligente aplicado a uma mesa de coordenadas de dois graus de liberdade

This work presents the design and construction of an X-Y table of two degrees of freedom, as well as the development of a fuzzy system for its position and trajectory control. The table is composed of two bases that move perpendicularly to each other in the horizontal plane, and are driven by two DC motors. Base position is detected by position sensors attached to the motor axes. A data acquisition board performs the interface between a laptop and the plant. The fuzzy system algorithm was implemented in LabVIEW® programming environment that processes the sensors signals and determines the control variables values that drive the motors. Experimental results using position reference signals (step type signal) and straight and circular paths reference signals are presented to demonstrate the dynamic behavior of fuzzy system

Seletividade e eficiência agronômica de herbicidas no controle de capim-colchão na cultura da melancia

Foi avaliada a seletividade e a eficiência agronômica dos herbicidas clethodim e sethoxydim, no controle de Digitaria horizontalis (capim-colchão) na cultura da melancia (cv. Crimson Sweet). O experimento foi conduzido em campo, no município de Floresta, PR, em 1995/96, em delineamento de blocos ao acaso, com quatro repetições. Os tratamentos avaliados foram clethodim nas doses de 84; 96 e 108 g i.a./ha adicionado de 1,0 L/ha de óleo mineral (Dytrol), sethoxydim na dose de 230 g i.a./ha adicionado de 1,0 L/ha de óleo mineral (Assist) e testemunhas com e sem capina. Os herbicidas foram aplicados em pós-emergência, quando a melancia apresentava ramas com 1,4 m e a D. horizontalis em estádio de três folhas a três perfilhos e densidade de 240 plantas/m². Para a aplicação dos herbicidas utilizou-se pulverizador costal de pressão mantida por injeção de CO2, equipado com pontas de jato plano XR110.02 e volume de calda de 200 L/ha. As avaliações de seletividade (Escala E.W.R.C.) e controle das plantas daninhas (0 - 100%) foram efetuadas aos 7; 15 e 30 dias após aplicação dos tratamentos. Os resultados indicaram que o herbicida clethodim, a partir de 96 g i.a./ha, controlou eficientemente a D. horizontalis, sendo estatisticamente superior ao herbicida sethoxydim e à testemunha sem capina. Nenhum dos tratamentos químicos causou fitotoxicidade que afetasse o desenvolvimento e a produção da melancia. A D. horizontalis interferiu no desenvolvimento da cultura, causando redução média de 36,0% da produção da melancia.

Implementação de um sistema embarcado aplicado ao controle de pressão arterial

Hypertension is a dangerous disease that can cause serious harm to a patient health. In some situations the necessity to control this pressure is even greater, as in surgical procedures and post-surgical patients. To decrease the chances of a complication, it is necessary to reduce blood pressure as soon as possible. Continuous infusion of vasodilators drugs, such as sodium nitroprusside (SNP), rapidly decreased blood pressure in most patients, avoiding major problems. Maintaining the desired blood pressure requires constant monitoring of arterial blood pressure and frequently adjusting the drug infusion rate. Manual control of arterial blood pressure by clinical personnel is very demanding, time consuming and, as a result, sometimes of poor quality. Thus, the aim of this work is the design and implementation of a database of tuned controllers based on patients models, in order to find a suitable PID to be embedded in a Programmable Integrated Circuit (PIC), which has a smaller cost, smaller size and lower power consumption. For best results in controlling the blood pressure and choosing the adequate controller, tuning algorithms, system identification techniques and Smith predictor are used. This work also introduces a monitoring system to assist in detecting anomalies and optimize the process of patient care.

Enxertia em plantas de pimentão no controle da murcha de fitóftora em ambiente protegido

Avaliou-se a viabilidade de utilização da enxertia em plantas de pimentão (Capsicum annuum, L.), visando o controle da murcha de fitóftora. A pesquisa foi conduzida de setembro de 2000 a julho de 2001, na UNESP, Botucatu, em ambiente protegido. Adotou-se o delineamento experimental de blocos ao acaso, com 4 repetições e 5 plantas por parcela. Foram utilizados dois porta-enxertos resistentes a Phytophthora capsici, híbridos F1 de Capsicum annuum, e três híbridos comerciais suscetíveis (Elisa, Margarita e Magali-R). A enxertia foi realizada quando porta-enxertos e enxertos apresentavam respectivamente sete e três folhas verdadeiras, pelo método de garfagem fenda simples. Aos 14 dias após o transplante das mudas foi feita a inoculação do fungo, utilizando sementes de trigo infestadas pelo patógeno, depositadas ao redor do colo da planta. Quatro dias após a inoculação, e a partir daí a cada 15 dias, foram feitas avaliações que confirmaram a resistência dos porta-enxertos e a suscetibilidade das plantas não enxertadas. Observou-se bom nível de compatibilidade de enxertia em todas as combinações, precocidade de florescimento das plantas não enxertadas, manutenção de resistência à doença pelas plantas enxertadas durante todo o período e variações na altura das plantas em algumas combinações. Com relação à produção, verificou-se que os frutos mantiveram as características fenotípicas de cada híbrido, revelando que não houve interferência dos porta-enxertos neste aspecto. Concluiu-se haver viabilidade técnica de utilização da enxertia no controle da murcha de fitóftora em ambiente protegido.

Análise do espalhamento espectral em superfícies de estruturas complexas para comunicações móveis

In this work, the transmission line method is explored on the study of the propagation phenomenon in nonhomogeneous walls with finite thickness. It is evaluated the efficiency and applicability of the method, considering materials like gypsum, wood and brick, found in the composition of the structures of walls in question. The results obtained in this work are compared to those available in the literature, for several particular cases. A good agreement is observed, showing that the performed analysis is accurate and efficient in modeling, for instance, the wave propagation through building walls and integrated circuit layers in mobile communication and radar system applications. Later, simulations of resistive sheets devices such as Salisbury screens and Jaumann absorbers and of transmission lines made of metal-insulator-semiconductor (MIS) are made. Thereafter, it is described a study on frequency surface selective structures (FSS). It is proposed the development of devices and microwave integrated circuits (MIC) of such structures, for the accomplishment of experiments. Finally, future works are suggested, for instance, on the development of reflectarrays, frequency selective surfaces with dissimilar elements, and coupled frequency selective surfaces with elements located on different layers

Controle inteligente de pressão para uma rede sem reservatório de abastecimento urbano de água

The sanitation companies from Brazil has a great challenge for the XXI century: seek to mitigate the rate of physical waste (water, chemicals and electricity) and financial waste caused by inefficient operating systems drinking water supply, considering that currently we already face, in some cases, the scarcity of water resources. The supply systems are increasingly complex as they seek to minimize waste and at the same time better serve the growing number of users. However, this technological change is to reduce the complexity of the challenges posed by the need to include users with higher quality and efficiency in services. A major challenge for companies of water supplies is to provide a good quality service contemplating reducing expenditure on electricity. In this situation we developed a research by a method that seeks to control the pressure of the distribution systems that do not have the tank in your setup and the water comes out of the well directly to the distribution system. The method of pressure control (intelligent control) uses fuzzy logic to eliminate the waste of electricity and the leaks from the production of pumps that inject directly into the distribution system, which causes waste of energy when the consumption of households is reduced causing the saturation of the distribution system. This study was conducted at Green Club II condominium, located in the city of Parnamirim, state of Rio Grande do Norte, in order to study the pressure behavior of the output of the pump that injects water directly into the distribution system. The study was only possible because of the need we had to find a solution to some leaks in the existing distribution system and the extensions of the respective condominium residences, which sparked interest in developing a job in order to carry out the experiments contained in this research

Desenvolvimento de esquema de controle com realimentação visual para um robô manipulador

This work proposes a kinematic control scheme, using visual feedback for a robot arm with five degrees of freedom. Using computational vision techniques, a method was developed to determine the cartesian 3d position and orientation of the robot arm (pose) using a robot image obtained through a camera. A colored triangular label is disposed on the robot manipulator tool and efficient heuristic rules are used to obtain the vertexes of that label in the image. The tool pose is obtained from those vertexes through numerical methods. A color calibration scheme based in the K-means algorithm was implemented to guarantee the robustness of the vision system in the presence of light variations. The extrinsic camera parameters are computed from the image of four coplanar points whose cartesian 3d coordinates, related to a fixed frame, are known. Two distinct poses of the tool, initial and final, obtained from image, are interpolated to generate a desired trajectory in cartesian space. The error signal in the proposed control scheme consists in the difference between the desired tool pose and the actual tool pose. Gains are applied at the error signal and the signal resulting is mapped in joint incrementals using the pseudoinverse of the manipulator jacobian matrix. These incrementals are applied to the manipulator joints moving the tool to the desired pose

Algoritmos genéricos para otimização de uma arquitetura de controle inteligente híerárquico

A hierarchical fuzzy control scheme is applied to improve vibration suppression by using an electro-mechanical system based on the lever principle. The hierarchical intelligent controller consists of a hierarchical fuzzy supervisor, one fuzzy controller and one robust controller. The supervisor combines controllers output signal to generate the control signal that will be applied on the plant. The objective is to improve the performance of the electromechanical system, considering that the supervisor could take advantage of the different techniques based controllers. The robust controller design is based on a linear mathematical model. Genetic algorithms are used on the fuzzy controller and the supervisor tuning, which are based on non-linear mathematical model. In order to attest the efficiency of the hierarchical fuzzy control scheme, digital simulations were employed. Some comparisons involving the optimized hierarchical controller and the non-optimized hierarchical controller will be made to prove the efficiency of the genetic algorithms and the advantages of its use

Construção e controle inteligente de um manipulador robótico com dois graus de liberdade

The present work shows the development and construction of a robot manipulator with two rotary joints and two degrees of freedom, driven by three-phase induction motors. The positions of the arm and base are made, for comparison, by a fuzzy controller and a PID controller implemented in LabVIEW® programming environment. The robot manipulator moves in an area equivalent to a quarter of a sphere. Experimental results have shown that the fuzzy controller has superior performance to PID controller when tracking single and multiple step trajectories, for the cases of load and no load

Controle de Manipulador Redundante Utilizando Realimentação Visual

In conventional robot manipulator control, the desired path is specified in cartesian space and converted to joint space through inverse kinematics mapping. The joint references generated by this mapping are utilized for dynamic control in joint space. Thus, the end-effector position is, in fact, controlled indirectly, in open-loop, and the accuracy of grip position control directly depends on the accuracy of the available kinematic model. In this report, a new scheme for redundant manipulator kinematic control, based on visual servoing is proposed. In the proposed system, a robot image acquired through a CCD camera is processed in order to compute the position and orientation of each link of the robot arm. The robot task is specified as a temporal sequence of reference images of the robot arm. Thus, both the measured pose and the reference pose are specified in the same image space, and its difference is utilized to generate a cartesian space error for kinematic control purposes. The proposed control scheme was applied in a four degree-of-freedom planar redundant robot arm, experimental results are shown

Desenvolvimento de um protocolo de comunicação para automação de subestações móveis via satélite

One of the most important decisions to turn a substation automatic and no attended it relates to the communication media between this substation and Operation Center. Generally energy companies uses radio or optic fiber, depending of distances and infrastructure of each situation. This rule applies to common substations. Mobile substations are a particular case, therefore they are conceived for use at provisional situations, emergencies, preventive or corrective maintenance. Thus the telecommunication solution used at common substations are not applied so easily to mobile substations, due absence of infrastructure (media) or difficulty to insert the mobile substation data in existing automation network not long. The ideal media must supply covering in a great geographic area to satisfy presented requirements. The implantation costs of this big infrastructure are expensive, however a existing operator may be used. Two services that fulfill that requirements are satellite and cellular telephony. This work presents a solution for automation of mobile substations through satellite. It was successfully implanted at a brazilian electric energy concessionaire named COSERN. The operation became transparent to operators. Other gotten benefits had been operational security, quality in the supply of electric energy and costs reduction. The project presented is a new solution, designed to substations and general applications where few data should be transmitted, but there is difficulties in relation to the media. Despite the satellite having been used, the same resulted can be gotten using celullar telephony, through Short Messages or packet networks as GPRS or EDGE.

Aplicação do método LTT às estruturas retangulares e triangulares em multicamadas e empilhadas em substratos PBG para comunicações móveis

Recently the planar antennas have been studied due to their characteristics as well as the advantages that they offers when compared with another types of antennas. In the mobile communications area, the need for this kind of antennas have became each time bigger due to the intense increase of the mobile communications that needs of antennas which operate in multifrequency and wide bandwidth. The microstrip antennas presents narrow bandwidth due the loss in the dielectric generated by radiation. Another limitation is the radiation pattern degradation due the generation of surface waves in the substrate. In this work some used techniques to minimize the disadvantages (previously mentioned) of the use of microstrip antennas are presented, those are: substrates with PBG material - Photonic Bandgap, multilayer antennas and with stacked patches. The developed analysis in this work used the TTL - Transverse Transmission Line method in the domain of Fourier transform, that uses a component of propagation in the y direction (transverse to the direction real of propagation z), treating the general equations of electric and magnetic field as functions of y and y . This work has as objective the application of the TTL method to microstrip structures with single and multilayers of rectangular and triangular patches, to obtaining the resonance frequency and radiation pattern of each structure. This method is applied for the treatment of the fields in stacked structures. The Homogenization theory will be applied to obtaining the effective permittivity for s and p polarizations of the substrate composed of PBG material. Numerical results for the triangular and rectangular antennas with single layer, multilayers resonators with triangular and rectangular patches are presented (in photonic and isotropic substrates). Conclusions and suggestions for continuity of this work are presented

Modelagem e controle adaptativo de uma planta didática de nível com instrumentação industrial

The control, automation and optimization areas help to improve the processes used by industry. They contribute to a fast production line, improving the products quality and reducing the manufacturing costs. Didatic plants are good tools for research in these areas, providing a direct contact with some industrial equipaments. Given these capabilities, the main goal of this work is to model and control a didactic plant, which is a level and flow process control system with an industrial instrumentation. With a model it is possible to build a simulator for the plant that allows studies about its behaviour, without any of the real processes operational costs, like experiments with controllers. They can be tested several times before its application in a real process. Among the several types of controllers, it was used adaptive controllers, mainly the Direct Self-Tuning Regulators (DSTR) with Integral Action and the Gain Scheduling (GS). The DSTR was based on Pole-Placement design and use the Recursive Least Square to calculate the controller parameters. The characteristics of an adaptive system was very worth to guarantee a good performance when the controller was applied to the plant