Long period gratings in multimode optical fibers: application in chemical sensing

We propose and demonstrate a new technique for evanescent wave chemical sensing by writing long period gratings in a bare multimode plastic clad silica fiber. The sensing length of the present sensor is only 10 mm, but is as sensitive as a conventional unclad evanescent wave sensor having about 100 mm sensing length. The minimum measurable concentration of the sensor reported here is 10 nmol/l and the operating range is more than 4 orders of magnitude. Moreover, the detection is carried out in two independent detection configurations viz., bright field detection scheme that detects the core-mode power and dark field detection scheme that detects the cladding mode power. The use of such a double detection scheme definitely enhances the reliability and accuracy of the results. Furthermore, the cladding of the present fiber need not be removed as done in conventional evanescent wave fiber sensors.

Selective mode excitation in dye-doped DNA polyvinyl alcohol thin film

A solid-state laser based on a dye-doped deoxyribonucleic acid (DNA) matrix is described. A thin solid film of DNA has been fabricated by treating with polyvinyl alcohol (PVA) and used as a host for the laser dye Rhodamine 6G. The edge emitted spectrum clearly indicated the existence of laser modes and amplified spontaneous emission. Lasing was obtained by pumping with a frequency-doubled Nd:YAG laser at 532 nm. For a pump energy of 10 mJ/pulse, an intense line with FWHM ≈0.2 nm was observed at 566 nm due to selective mode excitation.

Thermo- Optic and Nonlinear-Optical studies on CdSe Quantum Dots for Photonic Applications

In general, linear- optic, thermo- optic and nonlinear- optical studies on CdSe QDs based nano uids and their special applications in solar cells and random lasers have been studied in this thesis. Photo acous- tic and thermal lens studies are the two characterization methods used for thermo- optic studies whereas Z- scan method is used for nonlinear- optical charecterization. In all these cases we have selected CdSe QDs based nano uid as potential photonic material and studied the e ect of metal NPs on its properties. Linear optical studies on these materials have been done using vari- ous characterization methods and photo induced studies is one of them. Thermal lens studies on these materials give information about heat transport properties of these materials and their suitability for applica- tions such as coolant and insulators. Photo acoustic studies shows the e ect of light on the absorption energy levels of the materials. We have also observed that these materials can be used as optical limiters in the eld of nonlinear optics. Special applications of these materials have been studied in the eld of solar cell such as QDSSCs, where CdSe QDs act as the sensitizing materials for light harvesting. Random lasers have many applications in the eld of laser technology, in which CdSe QDs act as scattering media for the gain.

VUV-Laserablation von Spinnenseide

Spinnenseide gehört zu den stabilsten bekannten Polymerverbindungen. Spinnfäden können bis auf das Dreifache ihrer ursprünglichen Länge gedehnt werden, bevor sie reißen, und dabei mit rund 160 MJ/m³ mehr als dreimal soviel Energie absorbieren wie die stärkste synthetisch hergestellte Faser Kevlar (50 MJ/m³). Dabei weisen Spinnfäden mit 2 bis 5 Mikrometer nur ein Zehntel des Durchmessers eines menschlichen Haares auf. Das präzise, berührungslose Bearbeiten von Spinnenseide ist für verschiedene technische Anwendungen interessant, insbesondere wenn dabei ihre außergewöhnlichen Eigenschaften erhalten bleiben. Könnten die von Natur aus dünnen Seidenfäden gezielt in ihrem Durchmesser verringert werden, so wären sie unter anderem in der Mikroelektronik einzusetzen. Hier könnten sie als Trägermaterial für eine dünne, elektrisch leitfähige Schicht fungieren. Man erhielte Nanodrähte, die auch in mechanisch besonders belasteten Mikroelektronikbauteilen (MEMS) Verwendung finden könnten. In dieser Arbeit wird die Verwendung der laserinduzierten Ablation zur gezielten Bearbeitung von Haltefäden der Schwarzen Witwe (Latrodectus hesperus) beschrieben. Eingesetzt wurde ein VUV-Excimerlaser vom Typ LPF 205 (Lambda-Physik, Göttingen) mit einer Wellenlänge von 157 nm und einer Pulsdauer von 18 ns. Eine berührungslose Laserbearbeitung bei 157 nm erlaubt einen effizienten und präzisen Abtrag von Material durch Ablation aufgrund der geringen optischen Eindringtiefe von unter 100 nm oberhalb einer Schwellenfluenz (Energie/Fläche) von Φth=29 mJ/cm², ohne dabei das umgebende Material thermisch zu beeinträchtigen. Parallel zur Ablation setzt allerdings eine wellenförmige Oberflächenstrukturierung auf der Faseroberfläche ein, wodurch die mechanische Belastbarkeit der Faser entscheidend geschwächt wird. Die Ursache hierfür liegt im Abbau materialbedingter Spannungsfelder („stress release“) innerhalb einer durch das Laserlicht induzierten dünnen Schmelzschicht. Im Rahmen dieser Arbeit ist es nun gelungen, diese Strukturen durch einen anschließenden Glättungsprozeß zu entfernen. Dabei wird auf der bestrahlten Oberfläche mittels Laserlichts eine glatte Ablation erzielt. Mit feinerer Abstufung dieser Prozeßschritte konnte der Durchmesser des verwendeten Spinnenseidefadens zum Teil um 70 Prozent bis auf ca. 750 nm verringert werden. Durch Zugfestigkeitsexperimente wurde belegt, daß die mechanischen Eigenschaften der so bearbeiteten Spinnenseide weitgehend erhalten bleiben. Die im Rahmen dieser Arbeit angewandte Methode erlaubt somit eine präzise Laserablation von Spinnenseide und ähnlichen hochabsorbierenden Materialien, ohne deren Kernsubstanz in ihrer Beschaffenheit zu verändern.

Goldnanoteilchen auf Titandioxid

In dieser Arbeit wurde das Wachstum sowie die ultraschnelle Elektronendynamik des Oberflächenplasmon Polaritons von Goldnanoteilchen auf Titandioxid untersucht. Die Messung der Dephasierungszeit des Oberflächenplasmons von Nanoteilchen mit definierter Form und Größe erfolgte dabei mit der Methode des spektralen Lochbrennens. Die Nanoteilchen wurden durch Deposition von Goldatomen aus einem thermischen Atomstrahl mit anschließender Diffussion und Nukleation, d.h. Volmer-Weber-Wachstum, auf Titandioxidsubstraten hergestellt und mittels einer Kombination aus optischer Spektroskopie und Rasterkraftmikroskopie systematisch untersucht. Dabei lässt sich das Nanoteilchenensemble durch das mittlere Achsverhältnis und den mittleren Äquivalentradius charakterisieren. Die Messungen zeigen, dass die Proben große Größen- und Formverteilungen aufweisen und ein definierter Zusammenhang zwischen Größe und Form der Teilchen existiert. Während kleine Goldnanoteilchen nahezu kugelförmig sind, flachen die Teilchen mit zunehmender Größe immer mehr ab. Des Weiteren wurde in dieser Arbeit die Methode des lasergestützten Wachstums auf das System Gold auf Titandioxid angewendet. Systematische Untersuchungen zeigten, dass sich das Achsverhältnis der Teilchen durch geeignete Wahl von Photonenenergie und Fluenz des eingestrahlten Laserlichts definiert und gezielt vorgeben lässt. Die Methode des lasergestützten Wachstums erschließt damit den Bereich außerhalb der Zugänglichkeit des natürlichen Wachstums. Aufgrund der Formabhängigkeit der spektrale Lage der Plasmonresonanz ist man somit in der Lage, die optischen Eigenschaften der Nanoteilchen gezielt einzustellen und z.B. für technische Anwendungen zu optimieren. Die Untersuchung der ultraschnellen Elektronendynamik von Goldnanoteilchen auf Titandioxid mit äquivalenten Radien zwischen 8 bis 15 nm erfolgte in dieser Arbeit mit der Methode des spektralen Lochbrennes. Hierzu wurde die Dephasierungszeit des Oberflächenplasmons systematisch als Funktion der Photonenenergie in einem Bereich von 1,45 bis 1,85 eV gemessen. Es zeigte sich, dass die gemessenen Dephasierungszeiten von 8,5 bis 16,2 fs deutlich unter den in der dielektrischen Funktion von Gold enthaltenen Werten lagen, was den erwarteten Einfluss der reduzierten Dimension der Teilchen demonstriert. Um die Messwerte trotz verschiedener Teilchengrößen untereinander vergleichen und den Einfluss der intrinsischen Dämpfung quantifizieren zu können, wurde zusätzlich der Dämpfungsparameter A bestimmt. Die ermittelten A-Faktoren zeigten dabei eine starke Abhängigkeit von der Plasmonenergie. Für Teilchen mit Plasmonenergien von 1,45 bis 1,55 eV wurde ein Dämpfungsfaktor von A ~ 0,2 nm/fs ermittelt, der lediglich Oberflächenstreuung als dominierenden Dämpfungsmechanismus widerspiegelt. Hingegen wurde für Teilchen mit Plasmonenergien oberhalb von 1,55 eV ein drastischer Anstieg der Dämpfung auf A ~ 0,4 nm/fs beobachtet. Die erhöhte Dämpfung wurde dabei dem zusätzlichen Vorliegen einer chemischen Dämpfung durch das Titandioxidsubstrat zugeschrieben. Zusammenfassend zeigen die Ergebnisse somit, dass eine starke Abhängigkeit der chemischen Dämpfung von der Photonenenergie vorliegt. Es konnte erstmals nachgewiesen werden, dass die chemische Dämpfung erst ab einer bestimmten unteren Schwelle der Photonenenergie einsetzt, die für Goldnanoteilchen auf Titandioxid bei etwa 1,6 eV liegt.

Conditions for Viewpoint Dependent Face Recognition

Poggio and Vetter (1992) showed that learning one view of a bilaterally symmetric object could be sufficient for its recognition, if this view allows the computation of a symmetric, "virtual," view. Faces are roughly bilaterally symmetric objects. Learning a side-view--which always has a symmetric view--should allow for better generalization performances than learning the frontal view. Two psychophysical experiments tested these predictions. Stimuli were views of shaded 3D models of laser-scanned faces. The first experiment tested whether a particular view of a face was canonical. The second experiment tested which single views of a face give rise to best generalization performances. The results were compatible with the symmetry hypothesis: Learning a side view allowed better generalization performances than learning the frontal view.

Compositional data analysis in archaeometry

We shall call an n × p data matrix fully-compositional if the rows sum to a constant, and sub-compositional if the variables are a subset of a fully-compositional data set1. Such data occur widely in archaeometry, where it is common to determine the chemical composition of ceramic, glass, metal or other artefacts using techniques such as neutron activation analysis (NAA), inductively coupled plasma spectroscopy (ICPS), X-ray fluorescence analysis (XRF) etc. Interest often centres on whether there are distinct chemical groups within the data and whether, for example, these can be associated with different origins or manufacturing technologies

Efectos sesión por sesión de la depilación láser en axilas

Los resultados en depilación láser son variables entre los diferentes equipos y pacientes, alcanzando reducciones de hasta el 25% por sesión en la literatura disponible. En la práctica clínica se utiliza el conteo de pelos como instrumento para modificar parámetros de tratamiento y realizar cambios o combinaciones de los láseres con el fin de alcanzar la máxima reducción posible. Materiales y métodos: En una cohorte histórica se analizaron 298 sesiones (79 pacientes) a los que se determinó variables clínicas registradas de reducción de pelo con tres láseres diferentes, junto a parámetros para cada uno de los equipos, a un intervalo máximo de 90 días entre cada sesión. Resultados: Se evaluaron 79 mujeres para un total de 298 sesiones, con un rango de edad entre los 18 y 67 años, fototipo de piel III-V, intervalo entre sesiones de 14 a 90 días. Los equipos utilizados fueron Soprano XLi® (64.7%), Lightsheer® (18.4%) y Alexandrita (16.9%). Los promedios de reducción fueron en la primera sesión 43.3±32%, segunda sesión 55.8±42.1%, tercera sesión 48.1±16%, cuarta sesión 51.8±26.6%, quinta sesión 61.2±26.7%.(p<0.001). Se encontró una baja incidencia de complicaciones (7.6% de pacientes), siendo significativa la presencia de éstas con Lightsheer® y Alexandrita, a diferencia del Soprano®. Discusión: Éste estudio longitudinal mostró altas reducciones sesión a sesión comparadas con las disponibles en la literatura, independientemente del equipo utilizado. Soprano® presentó un mejor perfil de seguridad que Lightsheer® y Alexandrita.

Grado de aclaramiento de tatuajes y eventos adversos, posterior a una sesión con láser q-switch

Introducción: Los resultados de la remoción de tatuajes con láser de sesión a sesión según los parámetros utilizados son limitados en la literatura. Objetivo: Evaluar los cambios en el aclaramiento de tatuajes y factores asociados posterior a una sesión con láser y los efectos adversos. Materiales y Métodos: Estudio longitudinal retrospectivo de antes y después de 1 sesión de con láser para remoción de tatuajes, donde se determinaron parámetros del tratamiento, aclaramiento y efectos adversos. Resultados: Se evaluaron 35 pacientes para un total de 98 sesiones, fototipo de piel II y IV. Equipos utilizados laser Q-Switch Nd Yag 1064 (83.3%), láser Q-Switch Nd YAG 532(11.3%) y laser Q-Switch Rubí (4.1%). El aclaramiento posterior a la sesión de láser fue evaluado por dos evaluadores independientes, mostrando concordancia significativa (Kappa de 0.615, p<0.001), con aclaración en un 96% de los tatuajes después de la sesión de láser. (p< 0.001). Se encontraron cambios significativos entre la densidad de energía aplicada y las categorías de aclaramiento de la escala de 0 a 3, siendo a mayor densidad mayor el nivel de aclaramiento (p= 0.05). No se encontró asociación significativa entre el número de pases y el aclaramiento del tatuaje. Los efectos adversos fueron del 5.4%. Cicatriz 2%, hiperpigmentación 2% y hipopigmentación 1%. Conclusión: Posterior a una sesión de remoción de tatuajes con láser Q-Switch hay un aclaramiento significativo en un 96% asociado con la densidad de energía, a mayor densidad de energía mayor el nivel de aclaramiento y no al número de pases realizados.

Greenhouse whitefly (Homoptera : Aleyrodidae) dispersal under different UV-light environments

The greenhouse whitefly, Dialeurodes vaporariorum (Westwood) (Homoptera: Aleyrodidae), is known to respond to UV light (UV). Field studies were conducted to improve our understanding of the behavioral effects and practical implications of using UV-blocking plastic films for the control of whitefly. Adult whiteflies were released in outdoor-located choice-chamber experiments with compartments clad with a range of films that transmitted incident UV to different extents. In release-recapture experiments, a very small proportion of the whiteflies recovered had dispersed into compartments where the entire UV spectrum was blocked, whereas the major proportion preferred compartments with UV. Compartments clad with films that blocked LTV below 375 nm attracted significantly more whiteflies than films that blocked UV below 385 nm, whereas the absorption of LTV wavelengths above 385 nm did not show any further effect on whitefly numbers. A reduction in the side cladding of the compartments by > 20% significantly reduced the advantage of using LTV-blocking films. Adult whitefly did not discriminate between direct- and diffused-light environments, as long as the UV-absorbing properties of the films were equivalent. Whitefly dispersal was influenced by the time of the day when adult whitefly were released, with a higher proportion of whitelly avoiding compartments clad with LTV-blocking films, at times of the day when light intensities were higher. The future use of UV-blocking films as a potentially highly effective component of integrated pest management systems for the control of whitefly is discussed.

Do in vivo terahertz imaging systems comply with safety guidelines?

Techniques for the coherent generation and detection of electromagnetic radiation in the far infrared, or terahertz, region of the electromagnetic spectrum have recently developed rapidly and may soon be applied for in vivo medical imaging. Both continuous wave and pulsed imaging systems are under development, with terahertz pulsed imaging being the more common method. Typically a pump and probe technique is used, with picosecond pulses of terahertz radiation generated from femtosecond infrared laser pulses, using an antenna or nonlinear crystal. After interaction with the subject either by transmission or reflection, coherent detection is achieved when the terahertz beam is combined with the probe laser beam. Raster scanning of the subject leads to an image data set comprising a time series representing the pulse at each pixel. A set of parametric images may be calculated, mapping the values of various parameters calculated from the shape of the pulses. A safety analysis has been performed, based on current guidelines for skin exposure to radiation of wavelengths 2.6 µm–20 mm (15 GHz–115 THz), to determine the maximum permissible exposure (MPE) for such a terahertz imaging system. The international guidelines for this range of wavelengths are drawn from two U.S. standards documents. The method for this analysis was taken from the American National Standard for the Safe Use of Lasers (ANSI Z136.1), and to ensure a conservative analysis, parameters were drawn from both this standard and from the IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields (C95.1). The calculated maximum permissible average beam power was 3 mW, indicating that typical terahertz imaging systems are safe according to the current guidelines. Further developments may however result in systems that will exceed the calculated limit. Furthermore, the published MPEs for pulsed exposures are based on measurements at shorter wavelengths and with pulses of longer duration than those used in terahertz pulsed imaging systems, so the results should be treated with caution.

Thermal lens spectrometry in pyroelectric lithium niobate crystals

In this work, the light-induced lens effect due to thermal and/or photorefractive processes was studied in pyroelectric (undoped and Fe(2+)-doped) lithium niobate crystals (LiNbO(3)) using thermal lens spectrometry with a two-beam (pump-probe) mode-mismatched configuration. The measurements were carried out at two pump beam wavelengths (514.5 and 750 nm) to establish a full understanding of the present effects in this material (thermal and/or photorefractive). We present an easy-to-implement method to determine quantitative values of the pyroelectric coefficient (dPs/dT), its contribution to the thermal effect and other thermo-optical parameters like thermal diffusivity (D), thermal conductivity (K) and temperature coefficient of the optical path length change (ds/dT). These measurements were performed in LiNbO(3) and LiNbO(3): Fe (0.1 ppm Fe(2+)) crystals with c axis along the direction of laser propagation.

Buried screen-printed contacts for silicon solar cells

A Simple way to improve solar cell efficiency is to enhance the absorption of light and reduce the shading losses. One of the main objectives for the photovoltaic roadmap is the reduction of metalized area on the front side of solar cell by fin lines. Industrial solar cell production uses screen-printing of metal pastes with a limit in line width of 70-80 μm. This paper will show a combination of the technique of laser grooved buried contact (LGBC) and Screen-printing is able to improve in fine lines and higher aspect ratio. Laser grooving is a technique to bury the contact into the surface of silicon wafer. Metallization is normally done with electroless or electrolytic plating method, which a high cost. To decrease the relative cost, more complex manufacturing process was needed, therefore in this project the standard process of buried contact solar cells has been optimized in order to gain a laser grooved buried contact solar cell concept with less processing steps. The laser scribing process is set at the first step on raw mono-crystalline silicon wafer. And then the texturing etch; phosphorus diffusion and SiNx passivation process was needed once. While simultaneously optimizing the laser scribing process did to get better results on screen-printing process with fewer difficulties to fill the laser groove. This project has been done to make the whole production of buried contact solar cell with fewer steps and could present a cost effective opportunity to solar cell industries.

Steel Sheet Applications and Integrated Heat Management

Increasing energy use has caused many environmental problems including global warming. Energy use is growing rapidly in developing countries and surprisingly a remarkable portion of it is associated with consumed energy to keep the temperature comfortable inside the buildings. Therefore, identifying renewable technologies for cooling and heating is essential. This study introduced applications of steel sheets integrated into the buildings to save energy based on existing technologies. In addition, the proposed application was found to have a considerable chance of market success. Also, satisfying energy needs for space heating and cooling in a single room by using one of the selected applications in different Köppen climate classes was investigated to estimate which climates have a proper potential for benefiting from the application. This study included three independent parts and the results related to each part have been used in the next part. The first part recognizes six different technologies through literature review including Cool Roof, Solar Chimney, Steel Cladding of Building, Night Radiative Cooling, Elastomer Metal Absorber, and Solar Distillation. The second part evaluated the application of different technologies by gathering the experts’ ideas via performing a Delphi method. The results showed that the Solar Chimney has a proper chance for the market. The third part simulated both a solar chimney and a solar chimney with evaporation which were connected to a single well insulated room with a considerable thermal mass. The combination was simulated as a system to estimate the possibility of satisfying cooling needs and heating needs in different climate classes. A Trombe-wall was selected as a sample design for the Solar Chimney and was simulated in different climates. The results implied that the solar chimney had the capability of reducing the cooling needs more than 25% in all of the studied locations and 100% in some locations with dry or temperate climate such as Mashhad, Madrid, and Istanbul. It was also observed that the heating needs were satisfied more than 50% in all of the studied locations, even for the continental climate such as Stockholm and 100% in most locations with a dry climate. Therefore, the Solar Chimney reduces energy use, saves environment resources, and it is a cost effective application. Furthermore, it saves the equipment costs in many locations. All the results mentioned above make the solar chimney a very practical and attractive tool for a wide range of climates.

Estudo da viabilidade técnica para a Bolívia de painéis de gesso reforçados com fibra de vidro para paredes internas não portantes

Na construção civil, nos países em desenvolvimento como a Bolívia, continua-se usando técnicas e materiais na execução de paredes, similar a décadas passadas. Os painéis de gesso reforçados com fibra de vidro são uma alternativa de simplificação e agilização na execução das paredes internas não portantes. A presente dissertação objetiva mostrar a viabilidade técnica e econômica dos painéis para paredes internas, na Bolívia; para tanto realizou-se uma avaliação dos recursos disponíveis (gesso), com relação às reservas, produção e custos. A técnica adotada na produção dos painéis é a de pré-mistura, que permite a moldagem dos painéis manual ou mecanicamente com equipamentos simples e de baixo custo. O estudo do compósito de gesso reforçado com fibra de vidro (GRG) foi realizado com gesso brasileiro e com gesso boliviano, verificando-se o seu comportamento mecânico com diferentes teores de fibra de vidro. Verificou-se aumento da resistência a tração na flexão e diminuição da resistência a compressão com o aumento do teor de fibra de vidro. A avaliação do comportamento mecânico dos painéis foi feita através dos ensaios de impacto (corpo mole e corpo duro). Nos ensaios de corpo mole, verificou-se aumento da resistência com o aumento do teor de fibra de vidro. Os teores de 0,75% e 1,5% se mostraram suficientes para que os painéis de GRG satisfaçam os requisitos de desempenho para divisórias internas respectivamente para o gesso brasileiro e boliviano. O comportamento dos painéis nos ensaios de impacto de corpo duro foi satisfatório, tanto para painéis com fibra como para painéis sem fibra de vidro. No estudo preliminar de custos, verificou-se uma redução em torno de 36% para os painéis de GRG em relação às paredes intemas tradicionalmente usadas na Bolívia.