CRITERION OF POLYMER POLYMER MISCIBILITY DETERMINED BY VISCOMETRY

The criteria of polymer-polymer miscibility determined by viscometry are reviewed, and a new criterion is proposed based on the classical Huggins equation and the Huggins coefficient K(m) in the blends. It was found that, in a ternary (polymer-A)-(polymer-B)-solvent system, [GRAPHICS] In the absence of strong specific interaction forces between molecules that would encourage aggregation and at sufficiently low concentration, the above equation can be written thus: [GRAPHICS] This equation can be used to determine the miscibility of polymer blends, when: alpha greater-than-or-equal-to 0 miscible, alpha < 0 immiscible. It is found that the new criterion is reasonable and suitable to predict polymer-polymer miscibility by the viscometry method.

MISCIBILITY OF POLY(N-VINYL-2-PYRROLIDONE) WITH POLY(ETHER SULFONE) AND 2 PHENOLPHTHALEIN-BASED POLYMERS

Blends of poly(N-vinyl-2-pyrrolidone) (PVP) with poly(ether sulphone) and two phenolphthalein-based polymers, viz. phenolphthalein poly(ether ether sulphone) and phenolphthalein poly(ether ether ketone) were prepared by casting from a common solvent and studied by differential scanning calorimetry. It was found that all the PVP blends are miscible and show a single, composition-dependent glass transition temperature (T(g)). The T(g)-composition dependence has been analysed by the use of the Gordon-Taylor equation. The values of the k parameter in the Gordon-Taylor equation obtained are all not high for the three pairs, in accordance with the fact that there is no strongly specific interaction between PVP and any of the other polymers.

PHASE-SEPARATION IN ANHYDRIDE-CURED EPOXY-RESIN CONTAINING PHENOLPHTHALEIN POLY(ETHER ETHER KETONE)

Dynamic mechanical analysis and scanning electron microscopy were used to study phase separation of three blends of anhydride-cure bisphenol-A-type epoxy resin with phenolphthalein poly(ether ether ketone). Phase separation was observed for all the blends. The overall compatibility and the resulting morphology of the cured blends are dependent on the choice of cure agent. The phenomena have been discussed from the points of view of both thermodynamics and kinetics. The effects of the choice of hardener on phase separation are considered to be primarily due to differences between the chemical natures of the hardeners.

DYNAMIC SCALING OF THE STRUCTURE-FUNCTION FOR SPINODAL DECOMPOSITION IN CRITICAL AND NONCRITICAL MIXTURES OF POLY(VINYL ACETATE) POLY(METHYL METHACRYLATE)

The dynamics of phase separation in a binary polymer blend of poly(vinyl acetate) with poly(methyl methacrylate) was investigated by using a time-resolved light-scattering technique. In the later stages of spinodal decomposition, a simple dynamic scaling law was found for the scattering function S(q, t)(S(q, t) approximately I(q, t)): S(q, t)q(m)-3 S approximately (q/q(m)). The scaling function determined experimentally was in good agreement with that predicted by Furukawa, S approximately (X) approximately X2/(3 + X8) for critical concentration, and approximately in agreement with that predicted by Furukawa, S approximately (X) approximately X2/(3 + X6) for non-critical mixtures. The light-scattering invariant shows that the later stages of the spinodal decomposition were undergoing domain ripening.

EPITAXIAL CRYSTALLIZATION OF TRANS-1,4-POLYBUTADIENE ON HIGHLY ORIENTED ISOTACTIC POLY(PROPYLENE) FILMS

Epitaxial crystallization of trans-1,4-polybutadiene (PBD) on highly oriented isotactic poly(propylene) (iPP) has been investigated at different crystallization temperatures and rates. From electron microscopy and electron diffraction, it is confirmed that epitactic growth of the low-temperature modification (monoclinic) with microcrystals of PBD on the iPP films takes place with their chain directions about +/- 50-degrees apart. No epitaxial relationship occurs between the high-temperature modification (hexagonal) of PBD and the iPP substrate. Thermal analyses of PBD-PP layered films indicate that the epitaxy has an important effect on the formation of the high-temperature modification of PBD.

EPITAXIAL CRYSTALLIZATION OF SYNDIOTACTIC POLYPROPYLENE ON UNIAXIALLY ORIENTED POLYETHYLENE

The epitaxial crystallization of syndiotactic polypropylene (sPP) on uniaxially oriented polyethylene (PE) has been investigated by electron microscopy and electron diffraction. It is found that the sPP lamellae grow epitaxially on the PE substrate film with the preference in sPP for the b axis as the fast growth direction. Instead of 50-degrees as in the system of isotactic polypropylene with PE, the molecular chains of the sPP crystals are approximately +/- 37-degrees inclined to the chain direction of PE.

THE RING-BANDED SPHERULITE STRUCTURE OF POLY(EPSILON-CAPROLACTONE) IN ITS MISCIBLE MIXTURES WITH POLY(STYRENE-CO-ACRYLONITRILE)

The structure of the PCL spherulite in poly(epsilon-caprolactone)/poly(styrene-co-acrylonitrile) (PCL/SAN) blends was investigated by optical microscopy and small angle light scattering. The spherulite structure with a Maltese cross has been observed in pure PCL. Similar PCL/SAN blends exhibited not only spherulites with a Maltese cross, but also distinct extinction rings. The H(v) light scattering pattern especially caused diffraction rings in PCL/SAN blends but not in pure PCL. The spherical symmetry of spherulite PCL becomes more incomplete and the twist of the lamella becomes more irregular with increasing SAN content. It is found that the spherulite structure of PCL/SAN blends is dependent on the crystallization temperature and the concentration of SAN in PCL/SAN blends.

MISCIBILITY OF POLY(N-VINYL-2-PYRROLIDONE) WITH A COPOLYAMIDE

Blends of poly(N-vinyl-2-pyrrolidone) (PVP) with a copolyamide (CoPA) randomly composed of 1:1:1 (wt) nylon 6, nylon 66 and nylon 610 structural units were prepared by casting from a common solvent. They were found to be miscible and show a single, composition-dependent glass transition temperature (T(g)). The addition of PVP to CoPA significantly lowers the crystallinity owing to an increasing T(g) of the system. The observed miscibility is proposed to be the result of specific interactions between the proton acceptor groups of PVP and the amide groups of CoPA.

STRUCTURE AND PROPERTIES OF SEQUENTIALLY POLYMERIZED PROPYLENE-B-[ETHYLENE-CO-PROPYLENE]-B-PROPYLENE COPOLYMERS

The structure and properties of presumed block copolymers of polypropylene (PP) with ethylene-propylene random copolymers (EPR), i.e., PP-EPR and PP-EPR-PP, have been investigated by viscometry, transmission electron microscopy, dynamic mechanical analysis, differential scanning calorimetry, gel permeation chromatography, wide-angle x-ray diffraction, and other techniques testing various mechanical properties. PP-EPR and PP-EPR-PP were synthesized using delta-TiCl3-Et2AlCl as a catalyst system. The results indicate that the intrinsic viscosity of these polymers increases with each block-building step, whereas the intrinsic viscosity of those prepared by chain transfer reaction (strong chain-transfer reagent hydrogen was introduced between block-building steps during polymerization) hardly changes with the reaction time. Compared with PP / EPR blends, PP-EPR-PP block copolymers have lower PP and polyethylene crystallinity, and lower melting and crystallization temperatures of crystalline EPR. Two relaxation peaks of PP and EPR appear in the dynamic spectra of blends. They merge into a very broad relaxation peak with block sequence products of the same composition, indicating good compatibility between PP and EPR in the presence of block copolymers. Varying the PP and EPR content affects the crystallinity, density, and morphological structure of the products, which in turn affects the tensile strength and elongation at break. Because of their superior mechanical properties, sequential polymerization products containing PP-EPR and PP-EPR-PP block copolymers may have potential as compatibilizing agents for isotactic polypropylene and polyethylene blends or as potential heat-resistant thermoplastic elastomers.

RADIATION-INDUCED CROSS-LINKING OF POLY(METHYL METHACRYLATE)-POLY(ETHYLENE OXIDE) BLEND

Radiation-induced crosslinking of poly(methyl methacrylate) (PMMA)-poly(methylene oxide) (PEO) blends was studied. It was found that PMMA in PMMA-PEO blend can be crosslinked in the range of certain doses (1 approximately 20 x 10(4) Gy) and composition (PMMA% = 30 approximately 70) under the absence of oxygen. Moreover, it was also found that the crosslinking degree of PMMA in the blend in which the content of PMMA is 70% is the largest. The crosslinking degree of PMMA in the blend is closely related with the polymer miscibility. The crosslinking degree of the blend prepared at 60-degrees-C is far higher than one at ambient temperature.

CHARACTERIZATION, MORPHOLOGY AND THERMAL-PROPERTIES OF ETHYLENE PROPYLENE BLOCK COPOLYMERS

Characterization, morphology and thermal properties of commercial ethylene-propylene block copolymers have been studied by C-13 nuclear magnetic resonance (n.m.r.) spectroscopy, differential scanning calorimetry (d.s.c.), dynamic mechanical analysis (d.m.a.) and scanning electron microscopy (SEM). The results obtained show that there exists some ethylene-propylene random copolymer in the block copolymers extractable by n-heptane. The possibility of forming PP-b-PE diblock copolymer is questionable on the basis of the effects of residual propene and the chain-transfer reaction in the sequential copolymerization. A difference in the thermal properties between commercial ethylene-propylene block copolymers and PP/PE blends was noticed, which cannot be used to identify PP-b-PE diblock copolymer. The multiphase structure has been confirmed by d.m.a. and SEM, with ethylene-propylene random copolymer and polyethylene forming the domains in the matrix of polypropylene.

EPITAXIAL CRYSTALLIZATION OF HIGH-DENSITY POLYETHYLENE ON POLYPROPYLENE IN SOLUTION-CAST FILMS

Epitaxial crystallization of high-density polyethylene (HDPE) on isotactic polypropylene (iPP) in solution-cast films has been investigated by electron microscopy. The specimen-tilt technique of electron microscopy has been used to study the structural relationship between HDPE and iPP crystals. HDPE exhibits different crystalline morphologies in the two basic types of iPP spherulite textures, cross-hatched and lathlike regions. In the former, the crystallographic c axis of HDPE lamellae is in the film plane, while in the latter, the c axis of HDPE crystallites is at an angle of about 50-degrees with the normal of the film. In both structural regions of iPP, however, the contact planes of epitaxial growth are (0 1 0) for iPP and (1 0 0) for HDPE.

MISCIBILITY OF POLY(EPICHLOROHYDRIN) WITH POLY(VINYL ACETATE) AND POLY(STYRENE-CO-ACRYLONITRILE)

The phase behaviours of poly(vinyl acetate) (PVAc) and poly(styrene-co-acrylonitrile)s (SAN) with poly(epichlorohydrin) (PECH) were examined using differential scanning calorimetry and an optical method using a hot plate. The PECH/PVAc blends showed LCST behaviour. The observed miscibility is thought to be a result of hydrogen-bonding interactions between the alpha-hydrogen atoms of PECH and the carbonyl groups of PVAc. Two SAN copolymers with an acrylonitrile (AN) content of 18 wt% (SAN18) and 25 wt% (SAN25), respectively, were also found to exhibit miscibility with PECH. No phase separation occurred by heating up to about 280-degrees-C, and the individual blend has a single, composition-dependent glass transition temperature. The formation of miscible PECH/SAN blends can be considered as a result of the intramolecular repulsion between styrene and AN units in SAN.