Un conjunt de materials d'època tardo-republicana de la ciutat romana de Pollentia (Alcúdia, Mallorca)

El pou D 18, situat a la part sud-oest de la zona coneguda del forum de Pollentia, fou amortitzat en el segon quart del segle 1 a.C. EIs materials que formaven part del farciment constitueixen un conjunt tancat representatiu sobretot deIs tipus ceramics locals i d'importació utilitzats en aquesta epoca. El volum principal d'importacions correspon als productes italics, seguits a gran distancia pels materials púnics, iberics i egeus.

Designing and testing of a sensor based on a magnetoresistive manganese perovskite thick film

In this paper we report on the growth of thick films of magnetoresistive La2/3Sr1/3MnO3 by using spray and screen printing techniques on various substrates (Al2O3 and ZrO2). The growth conditions are explored in order to optimize the microstructure of the films. The films display a room-temperature magnetoresistance of 0.0012%/Oe in the 1 kOe field region. A magnetic sensor is described and tested.

Production of nanometric particles in radio frequency glow discharges in mixtures of silane and methane

The formation of silicon particles in rf glow discharges has attracted attention due to their effect as a contaminant during film deposition or etching. However, silicon and silicon alloy powders produced by plasma¿enhanced chemical vapor deposition (PECVD) are promising new materials for sintering ceramics, for making nanoscale filters, or for supporting catalytic surfaces. Common characteristics of these powders are their high purity and the easy control of their stoichiometry through the composition of the precursor gas mixture. Plasma parameters also influence their structure. Nanometric powders of silicon¿carbon alloys exhibiting microstructural properties such as large hydrogen content and high surface/volume ratio have been produced in a PECVD reactor using mixtures of silane and methane at low pressure (-1 Torr) and low frequency square¿wave modulated rf power (13.56 MHz). The a¿Si1¿xCx:H powders were obtained from different precursor gas mixtures, from R=0.05 to R=9, where R=[SiH4]/([SiH4]+[CH4]). The structure of the a¿Si1¿xCx:H powder was analyzed by several techniques. The particles appeared agglomerated, with a wide size distribution between 5 and 100 nm. The silane/methane gas mixture determined the vibrational features of these powders in the infrared. Silicon-hydrogen groups were present for every gas composition, whereas carbon¿hydrogen and silicon¿carbon bonds appeared in methane¿rich mixtures (R-0.6). The thermal desorption of hydrogen revealed two main evolutions at about 375 and 660¿°C that were ascribed to hydrogen bonded to silicon and carbon, respectively. The estimated hydrogen atom concentration in the sample was about 50%.

Playas fósiles sumergidas en la Costa Brava Meridional (Girona)

This paper describes petrologic and morphologic characteristics of fossil beaches submerged in the sector of the Costa Brava located between the Pals Beach and Blanes (Girona). These submerged beaches are composed of large-grain sandstone andconglomerate platforms, situated at a depth between 0.5 and 2.5 meters. These platforms are slightly inclinated towards the open sea. These deposits have been formed very recently, and date from Holocene, as noted by the presence of fragments of roman ceramics inside sandstone

The use of micro-XRD for the study of glaze color decorations

The compounds responsible for the colours and decorations in glass and glazed ceramics include: colouring agents (transition metal ions), pigments (micro-and nano-precipitates of compounds that either do not dissolve or recrystallize in the glassy matrix) and opacifiers (microcrystalline compounds with high light scattering capability). Their composition, structure and range of stability are highly dependent not only on the composition but also on the procedures followed to obtain them. Chemical composition of the colorants and crystallites may be obtained by means of SEM-EDX and WDX. Synchrotron Radiation micro-X-ray Diffraction has a small beam size adequate (10 to 50 microns footprint size) to obtain the structural information of crystalline compounds and high brilliance, optimal for determining the crystallites even when present in low amounts. In addition, in glass decorations the crystallites often appear forming thin layers (from 10 to 100 micrometers thick) and they show a depth dependent composition and crystal structure. Their nature and distribution across the glass/glazes decorations gives direct information on the technology of production and stability and may be related to the color and appearance. A selection of glass and glaze coloring agents and decorations are studied by means of SR-micro- XRD and SEM-EDX including: manganese brown, antimony yellow, red copper lusters and cobalt blue. The selection includes Medieval (Islamic, and Hispano Moresque) and renaissance tin glazed ceramics from the 10th to the 17th century AD.

Image Analysis of PCC and AC Pavements Using SEM Images, HR-346, 1994

The major objective of this work was to evaluate the potential of image analysis for characterizing air voids in Portland cement Concrete (PCC), voids and constituents of Asphalt Concrete (AC) and aggregate gradation in AC. Images for analysis were obtained from a scanning electron microscope (SEM). Sample preparation techniques are presented that enhance signal differences so that backscattered electron (BSE) imaging, which is sensitive to atomic number changes, can be effectively employed. Work with PCC and AC pavement core samples has shown that the low vacuum scanning electron microscope (LVSEM) is better suited towards rapid analyses. The conventional high vacuum SEM can also be used for AC and PCC analyses but some distortion within the sample matrix will occur. Images with improved resolution can be obtained from scanning electron microscope (SEM) backscatter electron (BSE) micrographs. In a BSE image, voids filled with barium sulfate/resin yield excellent contrast in both PCC and AC. There is a good correlation between percent of air by image analysis and linear traverse.

El poblament rural del Camp de Tarragona en època tardo-republicana (segles II-I aC)

This project consists of a study of the settlement of population during the Late Republican period in the Camp de Tarragona, an extensive agricultural plain in the shape of a crescent moon opening out towards the sea which constitutes the area of land in closest proximity to the capital, Tarraco. It does not therefore include the entirety of the ager Tarraconensis, which covered a considerably larger area. After reviewing the preceding Iberian presence in the area, the study focuses on the archaeological evidence corroborating the settlement of population referred to above and its evolution during the course of the two centuries prior to the rule of Augustus. Attention is also given to certain speciic themes, such as the centuriation of certain sectors, the presence of military checkpoints, the production of ceramics during the Republican period (at Fontscaldes and Valls) and the appearance of the irst Roman villas (El Moro and El Mas d’en Gras).

Surface modification of biomaterials for conjugation with human fetal osteoblasts.

Surface functionalization of hydroxyapatite (HA) and beta-tricalcium phosphate (TCP) bioceramics with chemical ligands containing a pyrrogallol moiety was developed to improve the adhesion of bone cell precursors to the biomaterials. Fast and biocompatible copper-free click reaction with azido-modified human fetal osteoblasts resulted in improved cell binding to both HA and TCP bioceramics, opening the way for using this methodology in the preparation of cell-engineered bone implants.

Insulin-Like growth-factor 1 myocardial expression decreases in chronic alcohol consumption

Background Chronic alcohol ingestion may cause severe biochemical and pathophysiological derangements to skeletal muscle. Unfortunately, these alcohol-induced events may also prime skeletal muscle for worsened, delayed, or possibly incomplete repair following acute injury. As alcoholics may be at increased risk for skeletal muscle injury, our goals were to identify the effects of chronic alcohol ingestion on components of skeletal muscle regeneration. To accomplish this, age- and gender-matched C57Bl/6 mice were provided normal drinking water or water that contained 20% alcohol (v/v) for 1820 wk. Subgroups of mice were injected with a 1.2% barium chloride (BaCl2) solution into the tibialis anterior (TA) muscle to initiate degeneration and regeneration processes. Body weights and voluntary wheel running distances were recorded during the course of recovery. Muscles were harvested at 2, 7 or 14 days post-injection and assessed for markers of inflammation and oxidant stress, fiber cross-sectional areas, levels of growth and fibrotic factors, and fibrosis. Results Body weights of injured, alcohol-fed mice were reduced during the first week of recovery. These mice also ran significantly shorter distances over the two weeks following injury compared to uninjured, alcoholics. Injured TA muscles from alcohol-fed mice had increased TNFα and IL6 gene levels compared to controls 2 days after injury. Total protein oxidant stress and alterations to glutathione homeostasis were also evident at 7 and 14 days after injury. Ciliary neurotrophic factor (CNTF) induction was delayed in injured muscles from alcohol-fed mice which may explain, in part, why fiber cross-sectional area failed to normalize 14 days following injury. Gene levels of TGFβ1 were induced early following injury before normalizing in muscle from alcohol-fed mice compared to controls. However, TGFβ1 protein content was consistently elevated in injured muscle regardless of diet. Fibrosis was increased in injured, muscle from alcohol-fed mice at 7 and 14 days of recovery compared to injured controls. Conclusions Chronic alcohol ingestion appears to delay the normal regenerative response following significant skeletal muscle injury. This is evidenced by reduced cross-sectional areas of regenerated fibers, increased fibrosis, and altered temporal expression of well-described growth and fibrotic factors.

Early Iron Age Pottery: A Quantitative Approach. Proceedings of the International Round Table organized by the Swiss School of Archaeology in Greece (Athens, Novembre 28-30, 2008).

Quantitative approaches in ceramology are gaining ground in excavation reports, archaeological publications and thematic studies. Hence, a wide variety of methods are being used depending on the researchers' theoretical premise, the type of material which is examined, the context of discovery and the questions that are addressed. The round table that took place in Athens on November 2008 was intended to offer the participants the opportunity to present a selection of case studies on the basis of which methodological approaches were discussed. The aim was to define a set of guidelines for quantification that would prove to be of use to all researchers. Contents: 1) Introduction (Samuel Verdan); 2) Isthmia and beyond. How can quantification help the analysis of EIA sanctuary deposits? (Catherine Morgan); 3) Approaching aspects of cult practice and ethnicity in Early Iron Age Ephesos using quantitative analysis of a Protogeometric deposit from the Artemision (Michael Kerschner); 4) Development of a ceramic cultic assemblage: Analyzing pottery from Late Helladic IIIC through Late Geometric Kalapodi (Ivonne Kaiser, Laura-Concetta Rizzotto, Sara Strack); 5) 'Erfahrungsbericht' of application of different quantitative methods at Kalapodi (Sara Strack); 6) The Early Iron Age sanctuary at Olympia: counting sherds from the Pelopion excavations (1987-1996) (Birgitta Eder); 7) L'aire du pilier des Rhodiens à Delphes: Essai de quantification du mobilier (Jean-Marc Luce); 8) A new approach in ceramic statistical analyses: Pit 13 on Xeropolis at Lefkandi (David A. Mitchell, Irene S. Lemos); 9) Households and workshops at Early Iron Age Oropos: A quantitative approach of the fine, wheel-made pottery (Vicky Vlachou); 10) Counting sherds at Sindos: Pottery consumption and construction of identities in the Iron Age (Stefanos Gimatzidis); 11) Analyse quantitative du mobilier céramique des fouilles de Xombourgo à Ténos et le cas des supports de caisson (Jean-Sébastien Gros); 12) Defining a typology of pottery from Gortyn: The material from a pottery workshop pit, (Emanuela Santaniello); 13) Quantification of ceramics from Early Iron Age tombs (Antonis Kotsonas); 14) Quantitative analysis of the pottery from the Early Iron Age necropolis of Tsikalario on Naxos (Xenia Charalambidou); 15) Finding the Early Iron Age in field survey: Two case studies from Boeotia and Magnesia (Vladimir Stissi); 16) Pottery quantification: Some guidelines (Samuel Verdan).

LRCW.NET: A web site with a virtual laboratory for the study of coarse and cooking wares in the Late Antique Mediterranean

This contribution presents the LRCW.net a website with a virtual laboratory intranet devoted to the study of coarse and cooking wares in the late Antique Mediterranean. It is designed as a public website with a virtual laboratory intranet. There, all institutions and researchers interested in the subject can work together towards a specific purpose such as the creation of an on-line ‘encyclopedia’ for these categories of ceramics. The LRCW.net website and the associated virtual laboratory are just a small part of a wider initiative that aims to create an on-line Encyclopedia for Ancient Ceramics in the Mediterranean.

T.P.M.T., alfarero ilerdense de terra sigillata

Damos noticia del primer alfarero conocido de terrra sigillata de la antigua Ilerda, -aunque no podemos sino conjeturar su nombre completo- tras los análisis de pasta que indican su condición de local. Se incide asimismo en la estimable fabricación de estas cerámicas (buen número de moldes), así como la cronología de las mismas.

Optimización de un nuevo método de preparación de óxidos mixtos tipo perovskita con vacantes de oxígeno.

Se han optimizado las condiciones para la deslitiación de compuestos de fórmula general La2/3-xLi3xTiO3 así como las de la posterior termólisis de compuestos de fórmula general La2/3-xTiO3-3x(OH)3x. En ambos procesos se mantiene la estructura perovskita cúbica Pm3m. Estudios preliminares de conductividad eléctrica indican que los compuestos La2/3-xTiO3-3x/2 obtenidos mediante química suave a partir de la perovskita de lantano y litio se comportan como semiconductores.

Assessment of dissolution techniques for the analysis of ceramic samples by plasma spectrometry

In this study, 13 ceramic samples were subjected to dissolution using three different procedures: (a) acid attack in open PTFE vessels with a mixture of HF-HClO4, (b) fusion of the sample with lithium metaborate and (c) microwave digestion in PTFE bombs. The samples used in the study had been previously analyzed by neutron activation analysis (NAA), X-ray fluorescence (XRF) and X-ray diffraction (XRD) and they cover a wide range of ceramics fired in different atmospheres and temperatures as well as different mineralogical and chemical compositions. The effectiveness of each procedure is evaluated in terms of its ability to dissolve the various mineralogical phases of the samples, of the number of elements that can be determined and of the time needed for the whole scheme of analysis to be completed.

Keraamisten teräpalojen käyttö niukkaseosteisten terästen lastuamiseen normaaleissa toimitustiloissa

Tämän tutkimuksen tavoitteena oli tutkia keraamisten kääntöterien soveltuvuus niukkaseosteräksille ja M-käsittelyn vaikutus teränkestoaikoihin. Lisäksi tavoitteena oli tutkia keraamiseosten erityisominaisuudet ja muodostaa käsitys keraamisilla kääntöterillä sorvaamisen erityisvaatimuksista. Kirjallisuusosassa selvitettiin tutkimushetkellä saatavissa olleet keraamiset teräaineseokset ja niiden ominaisuudet sekä selvitettiin keraamisten kääntöterien viimeaikaiset kehitystrendit. Lastuamistutkimus toteutettiin standardin ISO 3685:1993 mukaisesti, minkä lisäksi mitattiin lastuamisvoimat ja tehtiin kokeessa käytetyille terille lastunmurtokoe. Koemateriaalit olivat Imatra Steelin GreenCut, Hydax 25, M-käsittelemätön 42CrMo4 ja M-käsitelty MoC410M. Kokeissa käytetyt kääntöterät olivat eri valmistajien alumiinioksiditeriä, titaanikarbidiseostettuja alumiinioksiditeriä, kuituvahvisteisia ja yksi puhdas titaanikarbidiseosteinen terä. Koetulosten perusteella hyvän teränkestoajan saavuttamiseksi on tärkeää valita oikea keraamiseos ja sille soveltuvat parametrit. Oikein valituilla parametreilla M-terästä sorvattaessa tulokset ylittävät kovametalleilla saavutettavissa olevat arvot. Tulosten perusteella niukkaseostettujen terästen sorvaus onnistuu hyvin keraamisilla kääntöterillä, mutta kovametallisorvaukseen verrattuna syöttöä on laskettava ja lastuamisnopeutta lisättävä. Tämän työn tuloksia voidaan soveltaa sopivissa olosuhteissa toteutettavassa kappaletavaratuotannossa. Sovelluksen onnistuminen vaatii tukevat työstöolosuhteet ja riittävien lastuamisnopeuksien saavuttamisen.