Turbulent flow structures induced by an engine intake port

Magdeburg, Univ., Fak. für Verfahrens- und Systemtechnik, Diss., 2009

Reduced model for flow simulation in the burner region of lime shaft kilns

Magdeburg, Univ., Fak. für Verfahrens- und Systemtechnik, Diss., 2010

Simulation of lime calcination in normal shaft an parallel flow regenerative kilns

Magdeburg, Univ., Fak. für Verfahrens- und Systemtechnik, Diss., 2012

Granular flow and design studies in flighted rotating drums

Magdeburg, Univ., Fak. für Verfahrens- und Systemtechnik, Diss., 2013

Shapes in vector fields : methods for continuous deformations and surface-based flow visualizations

Magdeburg, Univ., Fak. für Informatik, Diss., 2013

Flow design optimization of blood pumps considering hemolysis

Magdeburg, Univ., Fak. für Verfahrens- und Systemtechnik, Diss., 2015

Untersuchungen zum Verletzungspotential handelsüblicher Soft-Air-Waffen mit einer Geschossenergie zwischen 0,08 Joule und 0,5 Joule

Magdeburg, Univ., Med. Fak., Diss., 2015

Stability and error analysis for a numerical scheme to approximate elastic flow

Otto-von-Guericke-Universität Magdeburg, Fakultät für Mathematik, Univ., Dissertation, 2015

Functional design of the air ventilation apparatus and overland excurions by teleosts / Karel F. Liem.

n.s. no.37(1987)

Material flow accounting of Spain

Material throughput is a means of measuring the so-called social metabolism, or physical dimensions of a society’s consumption, and can be taken as an indirect and approximate indicator of sustainability. Material flow accounting can be used to test the dematerialisation hypothesis, the idea that technological progress causes a decrease in total material used (strong dematerialisation) or material used per monetary unit of output (weak dematerialisation). This paper sets out the results of a material flow analysis for Spain for the period from 1980 to 2000. The analysis reveals that neither strong nor weak dematerialisation took place during the period analysed. Although the population did not increase considerably, materials mobilised by the Spanish economy (DMI) increased by 85% in absolute terms, surpassing GDP growth. In addition, Spain became more dependent on external trade in physical terms. In fact, its imports are more than twice the amount of its exports in terms of weight.

Material flow accounting of Mexico (1970-2003)

This technical background paper describes the methods applied and data sources used in the compilation of the 1980-2003 data set for material flow accounts of the Mexican economy and presents the data set. It is organised in four parts: the first part gives an overview of the Material Flow Accounting (MFA) methodology. The second part presents the main material flows of the Mexican economy including biomass, fossil fuels, metal ores, industrial minerals and, construction minerals. The aim of this part is to explain the procedures and methods followed, the data sources used as well as providing a brief evaluation of the quality and reliability of the information used and the accounts established. Finally, some conclusions will be provided.

Material Flow Accounting in Chile, Ecuador, Mexico and Peru (1980-2000)

In this paper we compare the resource flows of Chile, Ecuador, Mexico and Peru between 1980 and 2000. In this time span, the domestic extraction of materials increased in the four countries, mainly due to the mining sector in Chile and Peru, biomass and oil in Ecuador and construction minerals in Mexico. Imports and exports increased too, due to the increasing integration in the international markets, prompted by the liberalization policies undertaken by the four countries between the late 1970s and the late 1990s. The four countries had a negative physical trade balance for most of the period analyzed, meaning that their exports exceeded their imports in terms of weight. However, the increase of imports reduced the physical deficit in Chile, Mexico and Peru. Ecuador’s physical deficit was the highest and did not decrease in the period analyzed. Also, a diversification of exports away from bulk commodities could be observed in Chile and Mexico, and to a lesser extent in Peru, whereas in Ecuador the export sector remained mainly based on oil and biomass. More research is needed to explore the environmental effects of this phenomenon. Also, the indirect flows associated to the direct physical flows deserve to be subject to further analysis.

PulseCath iVAC 3LTM hemodynamic performance for simple assisted flow.

The PulseCath iVAC 3L? left ventricular assist device is an option to treat transitory left heart failure or dysfunction post-cardiac surgery. Assisted blood flow should reach up to 3 l/min. In the present in vitro model exact pump flow, depending on various frequencies and afterload was examined. Optimal flow was achieved with inflation/deflation frequencies of about 70-80/min. The maximal flow rate was achieved at about 2.5 l/min with a minimal afterload of 22 mmHg. Handling of the device was easy due to the connection to a standard intra-aortic balloon pump console. With increasing afterload (up to a simulated mean systemic pressure of 66 mmHg) flow rate and cardiac support are in some extent limited.

Numerical simulation of combined heat transfer phenomena (conduction, convection, and radiation). Application to he optimisation of thermal systems

Thermal systems interchanging heat and mass by conduction, convection, radiation (solar and thermal ) occur in many engineering applications like energy storage by solar collectors, window glazing in buildings, refrigeration of plastic moulds, air handling units etc. Often these thermal systems are composed of various elements for example a building with wall, windows, rooms, etc. It would be of particular interest to have a modular thermal system which is formed by connecting different modules for the elements, flexibility to use and change models for individual elements, add or remove elements without changing the entire code. A numerical approach to handle the heat transfer and fluid flow in such systems helps in saving the full scale experiment time, cost and also aids optimisation of parameters of the system. In subsequent sections are presented a short summary of the work done until now on the orientation of the thesis in the field of numerical methods for heat transfer and fluid flow applications, the work in process and the future work.

The study of insect blood-feeding behaviour: 2. Recording techniques and the use of flow charts

This paper continues a discussion of approaches and methodologies we have used in our studies of feeding in haematophagous insects. Described are techniques for directly monitoring behaviour: electrical recording of feeding behaviour via resistance changes in the food canal, optical methods for monitoring mouthpart activity, and a computer technique for behavioural event recording. Also described is the use of "flow charts" or "decision diagrams" to model interrelated sequences of behaviours.