Conversão do metanol em olefinas catalisada por zeólitas com diferentes características ácidas e estruturais

A reação de transformação de metanol em olefinas leves foi investigada sobre as peneiras moleculares HZSM-5, HFER, SAPO-34 e HMCM-22. A caracterização físico-química das amostras foi realizada através das técnicas de FRX, DRX, fisissorção de nitrogênio, MEV, espectrometria no IV com adsorção de piridina e TPD de NH3. O desempenho catalítico das mesmas foi comparado em condições de isoconversão inicial de 755%. Verificou-se que as características ácidas e estruturais exerceram forte influência sobre o desempenho catalítico quanto à atividade, estabilidade e seletividade aos produtos da reação. A amostra mais estável foi a HZSM-5 que apresentou maior densidade de sítios fortes e uma estrutura porosa que permite uma circulação tridimensional das moléculas. Já a menos estável, SAPO-34, apresentou a menor concentração de sítios ácidos fortes dentre os materiais estudados e uma estrutura com cavidades com aberturas estreitas (4Å) que oferecem restrições ao acesso dos reagentes aos sítios ácidos do catalisador. Quanto à seletividade a olefinas, a primeira foi mais seletiva a propeno e a segunda, a eteno. A ferrierita não se mostrou seletiva às olefinas leves tendo apresentado, no entanto, comportamento promissor quanto a formação de DME a partir do metanol. Já a HMCM-22 foi seletiva às olefinas leves e aos hidrocarbonetos com 4, 5 e 6 ou mais átomos de carbono. A influência da temperatura no desempenho catalítico foi investigada variando-se a temperatura de reação (300, 400 e 500C). Verificou-se que para a HZSM-5 e HMCM-22, perda da atividade catalítica foi intensificada a partir de 400C. Quanto à seletividade a olefinas leves, apenas a SAPO-34 não se mostrou sensível a variações na temperatura, efeito este que foi nitidamente observado nos outros três catalisadores: um aumento na temperatura promoveu um aumento na seletividade a olefinas leves no caso da HZSM-5 e da HMCM-22 e queda nesse valor para a HFER

Remoção de compostos sulfurados e nitrogenados de diesel hidrotratado por adsorção em argila, alumina e sílica-alumina, impregnadas com metais de transição

Na matriz energética brasileira, o óleo diesel tem lugar de destaque, porém ainda é comercializado com teores de compostos sulfurados e nitrogenados considerados altos para as legislações ambientais que entrarão em vigor nos próximos anos. Tradicionalmente, a remoção desses compostos de enxofre de correntes de petróleo é realizada por processos de hidrotratamento (HDT). No entanto, devido as características do diesel brasileiro, se faz necessária maior severidade para atingir as novas especificações dos combustíveis. Isto implica em investimentos e custos operacionais crescentes para atender a demanda que se instala. Neste contexto, a adsorção está sendo estudada para a purificação da corrente de óleo diesel oriunda da etapa de hidrotratamento como polimento final para alcançar as especificações mais exigentes. Sabe-se que os adsorventes comerciais apresentam limitações na remoção destes contaminantes e uma alternativa que tem se mostrado promissora é a incorporação de metais de transição na estrutura do sólido. No presente trabalho foram modificados adsorventes comerciais, tais como aluminas, sílica-aluminas e argilas pela introdução dos elementos níquel, colbalto e molibdênio e testado o desempenho dessas modificações frente à adsorção de compostos sulfurados e nitrogenados presentes em um diesel hidrotratado. Foram feitas caracterizações químicas, físicas, texturais e morfológicas dos sólidos com e sem incorporação de metais de transição na estrutura original. Os experimentos de adsorção foram realizados a 40C. Avaliando todos os sólidos, o adsorvente que mostrou o melhor desempenho na remoção de compostos sulfurados e nitrogenados por massa de adsorvente foi a sílica-alumina sem modificações, que foi capaz de remover em torno de 90% de compostos nitrogenados e 55 % de sulfurados para 2 g de sólido / 10 mL de diesel. Para os materiais modificados, observou-se que a incorporação dos metais de transição ocasionou redução da sua área superficial e do volume total de poros. Desta maneira, os efeitos esperados pelas interações entre o sítios metálicos e os compostos de nitrogênio e enxofre foram reduzidos

Force chains, friction, and flow: Behavior of granular media across length scales

We study the behavior of granular materials at three length scales. At the smallest length scale, the grain-scale, we study inter-particle forces and "force chains". Inter-particle forces are the natural building blocks of constitutive laws for granular materials. Force chains are a key signature of the heterogeneity of granular systems. Despite their fundamental importance for calibrating grain-scale numerical models and elucidating constitutive laws, inter-particle forces have not been fully quantified in natural granular materials. We present a numerical force inference technique for determining inter-particle forces from experimental data and apply the technique to two-dimensional and three-dimensional systems under quasi-static and dynamic load. These experiments validate the technique and provide insight into the quasi-static and dynamic behavior of granular materials.

At a larger length scale, the mesoscale, we study the emergent frictional behavior of a collection of grains. Properties of granular materials at this intermediate scale are crucial inputs for macro-scale continuum models. We derive friction laws for granular materials at the mesoscale by applying averaging techniques to grain-scale quantities. These laws portray the nature of steady-state frictional strength as a competition between steady-state dilation and grain-scale dissipation rates. The laws also directly link the rate of dilation to the non-steady-state frictional strength.

At the macro-scale, we investigate continuum modeling techniques capable of simulating the distinct solid-like, liquid-like, and gas-like behaviors exhibited by granular materials in a single computational domain. We propose a Smoothed Particle Hydrodynamics (SPH) approach for granular materials with a viscoplastic constitutive law. The constitutive law uses a rate-dependent and dilation-dependent friction law. We provide a theoretical basis for a dilation-dependent friction law using similar analysis to that performed at the mesoscale. We provide several qualitative and quantitative validations of the technique and discuss ongoing work aiming to couple the granular flow with gas and fluid flows.

Study of oscillatory behavior of recording process arising from electron-hole competition in strongly oxidized LiNbO3 : Ce : Cu

We have investigated ultraviolet (UV) photorefractive effect of lithium niobate doubly doped with Ce and Cu. It is found the diffraction efficiency shows oscillating behavior Under UV-1ight-recording. A model in which electrons and holes can be excited from impurity centers in the UV region is proposed to study the oscillatory behavior of the diffraction efficiency. Oil the basis of the material equations and the coupled-wave equations, we found that the oscillatory behavior is due to the oscillation of the relative spatial phase shift Phi. And the electron-hole competition may cause the oscillation of the relative spatial phase shift. A switch point from electron grating to hole grating is chosen to realize nonvolatile readout by a red light with high sensitivity (0.4 cm/J). (c) 2005 Elsevier GmbH. All rights reserved.

Behavior of spherical particles at low Reynolds numbers in a fluctuating translational flow

The behavior of spheres in non-steady translational flow has been studied experimentally for values of Reynolds number from 0.2 to 3000. The aim of the work was to improve our qualitative understanding of particle transport in turbulent gaseous media, a process of extreme importance in power plants and energy transfer mechanisms.

Particles, subjected to sinusoidal oscillations parallel to the direction of steady translation, were found to have changes in average drag coefficient depending upon their translational Reynolds number, the density ratio, and the dimensionless frequency and amplitude of the oscillations. When the Reynolds number based on sphere diameter was less than 200, the oscillation had negligible effect on the average particle drag.

For Reynolds numbers exceeding 300, the coefficient of the mean drag was increased significantly in a particular frequency range. For example, at a Reynolds number of 3000, a 25 per cent increase in drag coefficient can be produced with an amplitude of oscillation of only 2 per cent of the sphere diameter, providing the frequency is near the frequency at which vortices would be shed in a steady flow at the mean speed. Flow visualization shows that over a wide range of frequencies, the vortex shedding frequency locks in to the oscillation frequency. Maximum effect at the natural frequency and lock-in show that a non-linear interaction between wake vortex shedding and the oscillation is responsible for the increase in drag.

Analysis and adsorption of phosalone on aquatic sediment

Phosalone is a non systematic, wide spectrum organophosphate pesticide which was discovered in 1961 in the laboratories of the Societe des Usines Chimique Rhone-Poulenc in France. It has been approved for commercial use since 1964 in France, in Australia since 1966, in the United Kingdom in 1967 and in many other countries including Japan, Egypt, USSR and the USA. This study provides a full literature review on all aspects of phosalone including its physical, biological and chemical characteristics, and analytical methods of analysis with particular reference to soils/sediments. Furthermore, it aims to develop a method for the determintion of phosalone in aquatic sediments and to determine the adsorption of phosalone onto kaolinite.

Thermodynamic and kinetic behavior of an argon plasma jet. Decomposition of nitric oxide between 1300 - 1750 degrees K in an argon plasma

In the first part of the study, an RF coupled, atmospheric pressure, laminar plasma jet of argon was investigated for thermodynamic equilibrium and some rate processes.

Improved values of transition probabilities for 17 lines of argon I were developed from known values for 7 lines. The effect of inhomogeneity of the source was pointed out.

The temperatures, T, and the electron densities, n_e , were determined spectroscopically from the population densities of the higher excited states assuming the Saha-Boltzmann relationship to be valid for these states. The axial velocities, v_z, were measured by tracing the paths of particles of boron nitride using a three-dimentional mapping technique. The above quantities varied in the following ranges: 10¹² ˂ n_e ˂ 10¹⁵ particles/cm³, 3500 ˂ T ˂ 11000 °K, and 200 ˂ v_z ˂ 1200 cm/sec.

The absence of excitation equilibrium for the lower excitation population including the ground state under certain conditions of T and n_e was established and the departure from equilibrium was examined quantitatively. The ground state was shown to be highly underpopulated for the decaying plasma.

Rates of recombination between electrons and ions were obtained by solving the steady-state equation of continuity for electrons. The observed rates were consistent with a dissociative-molecular ion mechanism with a steady-state assumption for the molecular ions.

In the second part of the study, decomposition of NO was studied in the plasma at lower temperatures. The mole fractions of NO denoted by x_NO were determined gas-chromatographically and varied between 0.0012 ˂ x_NO ˂ 0.0055. The temperatures were measured pyrometrically and varied between 1300 ˂ T ˂ 1750°K. The observed rates of decomposition were orders of magnitude greater than those obtained by the previous workers under purely thermal reaction conditions. The overall activation energy was about 9 kcal/g mol which was considerably lower than the value under thermal conditions. The effect of excess nitrogen was to reduce the rate of decomposition of NO and to increase the order of the reaction with respect to NO from 1.33 to 1.85. The observed rates were consistent with a chain mechanism in which atomic nitrogen and oxygen act as chain carriers. The increased rates of decomposition and the reduced activation energy in the presence of the plasma could be explained on the basis of the observed large amount of atomic nitrogen which was probably formed as the result of reactions between excited atoms and ions of argon and the molecular nitrogen.

Chemical and Electrochemical Behavior of Graphene-Covered Silicon Photoanodes

This dissertation describes efforts over the last five years to develop protective layers for semiconductor photoelectrodes based on monolayer or few-layer graphene sheets. Graphene is an attractive candidate for a protective layer because of its known chemical inertness, transparency, ease of deposition, and limited number of electronic states. Monolayer graphene was found to effectively inhibit loss of photocurrent over 1000 seconds at n-Si/aqueous electrolyte interfaces that exhibit total loss over photocurrent over 100 seconds. Further, the presence of graphene was found to effect only partial Fermi level pinning at the Si/graphene interface with respect to a range of nonaqueous electrolytes. Fluorination of graphene was found to extend the stability imparted on n-Si by the monolayer sheet in aqueous Fe(CN)₆^3-/4- electrolyte to over 100,000 seconds. It was demonstrated that the stability of the photocurrent of n-Si/fluorinated graphene/aqueous electrolyte interfaces relative to n-Si/aqueous electrolyte interfaces is likely attributable to the inhibition of oxidation of the silicon surface.

This dissertation also relates efforts to describe and define terminology relevant to the field of photoelectrochemistry and solar fuels production. Terminology describing varying interfaces employed in electrochemical solar fuels devices are defined, and the research challenges associated with each are discussed. Methods for determining the efficiency of varying photoelectrochemical and solar-fuel-producing cells from the current-voltage behavior of the individual components of such a device without requiring the device be constructed are described, and a range of commonly employed performance metrics are explored.

Estudo de adsorção de ácidos naftênicos a partir de correntes de hidrocarbonetos

Ácidos naftênicos correspondem à complexa mistura de ácidos carboxílicos presentes no petróleo, responsáveis diretamente pela sua acidez e pela sua corrosividade em fase líquida durante o refino. Tais compostos também estão presentes nas frações destiladas do petróleo, causando diversos problemas na qualidade final do produto. Uma possível forma de remover esses ácidos das frações destiladas é através da adsorção em materiais porosos. Contudo, os resultados até então apresentados indicam que resinas trocadoras de íons seriam os melhores adsorventes destes compostos, o que poderia aumentar o custo do processo e diminuir sua viabilidade. Neste trabalho, dois adsorventes comerciais (argila e alumina ativada) foram caracterizados por diversas técnicas físico-químicas e avaliados quanto à sua capacidade de remover os ácidos naftênicos de frações médias e pesadas de petróleo. Avaliou-se, ainda, para fins de comparação, o comportamento de ácidos naftênicos comerciais em óleos sintéticos preparados com óleo mineral. Em complementação, a corrosividade do aço carbono nos meios estudados foi também verificada. A argila apresentou maior afinidade com os ácidos naftênicos, tendo capacidade de adsorção superior e cinética de processo ligeiramente mais rápida às da alumina para as cargas sintéticas. No entanto, em virtude da maior concorrência pelos sítios de adsorção, apresentada pelos outros componentes presentes em óleos reais, observou-se uma perda na eficiência para estas amostras. Neste caso, a alumina apresentou melhores resultados. Embora ambos adsorventes tenham apresentado boa capacidade de remoção do soluto, a resina trocadora de íons ainda apresentou resultado mais eficaz para as amostras reais. Nas condições desse estudo, a taxa de corrosão do aço nas amostras sintéticas e em duas das reais não foi significativa e apenas uma delas apresentou-se corrosiva (Óleo 1). No entanto, a remoção dos ácidos naftênicos por adsorção conseguiu reduzir a taxa de corrosão neste meio em até 99%

Produção de biodiesel a partir da alcoólise do óleo de palma

No presente trabalho foi investigada a produção de biodiesel a partir da alcoólise do óleo de palma catalisada por lipase imobilizada comercial. O efeito da razão molar de álcool:óleo, da forma de adição do álcool (única e escalonada), da temperatura de reação, da concentração de enzima, do tipo de álcool (metanol e etanol), do tipo de enzima e da reutilização da enzima no rendimento final de reação foi avaliado. As reações conduzidas com etanol apresentaram rendimentos superiores aos obtidos com o emprego de metanol devido à maior desativação da lipase pelo álcool de menor número de átomos de carbono. O maior rendimento em biodiesel (54%) foi obtido empregando razão molar de álcool:óleo de 3:1, com adição escalonada de etanol (0, 30 e 60 minutos), 9% (m/m) de Lipozyme TL IM a 50C. Não foi possível recuperar a lipase ao final das reações, pois a matriz de imobilização se solubilizou no meio. Além disso, para comparação, foi investigada a utilização das lipases comerciais imobilizadas Lipozyme RM IM e Novozym 435 e dos catalisadores químicos KOH, MgO e La2O3. O rendimento em biodiesel nas reações catalisadas pelas lipases foi maior do que os obtidos com catalisadores químicos. A menor eficiência dos catalisadores químicos pode ser justificada pelo alto índice de acidez do óleo de palma (6,26 mg KOH.g-1) que promove o consumo do catalisador (KOH), devido à neutralização dos ácidos graxos livres presentes no óleo, e o bloqueio dos sítios ativos dos catalisadores químicos sólidos devido à adsorção dos ácidos graxos nestes sítios

A singular perturbation method of calculating the behavior of supercavitating hydrofoils with rounded noses

A simple, direct and accurate method to predict the pressure distribution on supercavitating hydrofoils with rounded noses is presented. The thickness of body and cavity is assumed to be small. The method adopted in the present work is that of singular perturbation theory. Far from the leading edge linearized free streamline theory is applied. Near the leading edge, however, where singularities of the linearized theory occur, a non-linear local solution is employed. The two unknown parameters which characterize this local solution are determined by a matching procedure. A uniformly valid solution is then constructed with the aid of the singular perturbation approach.

The present work is divided into two parts. In Part I isolated supercavitating hydrofoils of arbitrary profile shape with parabolic noses are investigated by the present method and its results are compared with the new computational results made with Wu and Wang's exact "functional iterative" method. The agreement is very good. In Part II this method is applied to a linear cascade of such hydrofoils with elliptic noses. A number of cases are worked out over a range of cascade parameters from which a good idea of the behavior of this type of important flow configuration is obtained.

Some of the computational aspects of Wu and Wang's functional iterative method heretofore not successfully applied to this type of problem are described in an appendix.

Chemical and electrochemical investigations of cobalt cyanide and ruthenium ammine complexes

Part I.

The stoichiometry and kinetics of the reaction between Co(CN₅H^3- and HgX₂ (X = CN, OH) have been investigated. The products of the reaction are two new complexes, [(NC)₅Co-HgX]^3- and [(NC)₅Co-Hg-Co(CN)₅]^6-, whose spectra are reported. The kinetic measurements produced a value for the forward rate constant of the reaction Co(CN)₅H^3- + OH^- k₁/k_-1 Co(CN)₅^4- +H₂O, k1 = (9.7 ± 0.8) x 10^-2 M^-1 sec^-1 at 24°C, and an equilibrium constant for the reaction K = 10^-6 M^-1.

Part II.

Unusually large and sharp "adsorption waves" appear in cyclic voltammograms of Co(CN)₅^3- and several cobalt(III) pentacyano complexes at stationary mercury electrodes. The nature of the adsorbed species and the reasons for the absence of the adsorption waves in polarograms taken with a d.m.e. have been examined. The data are compatible with the adsorption, in all cases, of a coordinatively unsaturated cobalt(II) complex, Co(CN)₄^2-, by means of a cobalt-mercury bond. When the resulting adsorbed complex is reduced, a series of subsequent chemical and electrode reactions is initiated in which three faradays of charge are consumed for each mole of adsorbed complex. The adsorption of the anionic complex strongly retards the reduction of other negatively charged complexes.

Part III.

A number of formal redox potentials for Ru^III (NH₃)₅L + e = Ru^II (NH₃)₅L and Ru^III(NH₃)₄L₂ + e = Ru^II (NH₃)₄L₂ (where L is various ligands) has been measured by cyclic voltammetry, potentiometry, and polarography and are discussed in terms of the properties of the ligands, such as π-accepting capability. Reduction of coordinated pyrazine in the complexes, Ru(NH₃)₅ Pz²⁺, cis- and trans-Ru(NH₃)₄Pz₂²⁺, on a mercury electrode has been observed. The behavior of this reduction in various acidity of the solution as well as the reoxidation of the reduction products are discussed.

Behavior ecology of the Humboldt squid, Dosidicus gigas: insights from an animal-borne video and data logging system

Dosidicus gigas is a large pelagic cephalopod of the eastern Pacific that has recently undergone an unexpected, significant range expansion up the coast of North America. The impact that such a range expansion is expected to have on local fisheries and marine ecosystems has motivated a thorough study of this top predator, a squid whose lifestyle has been quite mysterious until recently. Unfortunately, Dosidicus spends daylight hours at depths prohibitive to making observations without significant artificial interference. Observations of this squid‟s natural behaviors have thus far been considerably limited by the bright illumination and loud noises of remotely-operated-vehicles, or else the presence of humans from boats or with SCUBA. However, recent technological innovations have allowed for observations to take place in the absence of humans, or significant human intrusion, through the use of animal-borne devices such as National Geographic‟s CRITTERCAM. Utilizing the advanced video recording and data logging technology of this device, this study seeks to characterize unknown components of Dosidicus gigas behavior at depth. Data from two successful CRITTERCAM deployments reveal an assortment of new observations concerning Dosidicus lifestyle. Tri-axial accelerometers enable a confident description of Dosidicus orientation during ascents, descents, and depth maintenance behavior - previously not possible with simple depth tags. Video documentation of intraspecific interactions between Dosidicus permits the identification of ten chromatic components, a previously undescribed basal chromatic behavior, and multiple distinct body postures. And finally, based on visualizations of spermatophore release by D. gigas and repetitive behavior patterns between squid pairs, this thesis proposes the existence of a new mating behavior in Dosidicus. This study intends to provide the first glimpse into the natural behavior of Dosidicus, establishing the groundwork for a comprehensive ethogram to be supported with data from future CRITTERCAM deployments. Cataloguing these behaviors will be useful in accounting for Dosidicus‟ current range expansion in the northeast Pacific, as well as to inform public interest in the impacts this expansion will have on local fisheries and marine ecosystems.