Direct determination of calcium in milk by atomic absorption spectrometry using flow-injection analysis

A flow-injection system with sample and reagent addition by the synchronous merging zones approach for calcium determination in milk by flame AAS is proposed. Main parameters were optimized using a factorial design with central point. The optimum conditions were 2.5% (m/v) for La concentration, 8 mL min-1 for the carrier flow-rate, 20 cm for coiled reactor and 250 ìL for sample volume. Different sample preparation procedures were evaluated such as dilution in water or acid and microwave-assisted decomposition using concentrated or diluted acids. The optimized flow system was applied to determine Ca in eleven commercial milk samples and two standard reference materials diluted in water. Similar calcium levels were encountered comparing the results obtained by the proposed method (dilution in water) with those obtained using microwave-oven digestion. Results obtained in two standard reference materials were in agreement at 95% confidence level with those certified. Recoveries of spiked samples were in the 93% - 116% range. Relative standard deviation (n = 12) was < 5.4% and the sample throughput was 150 measurements per hour, corresponding to a consumption of 250 µL of sample and 6.25 mg La per determination.

SMB-laitteiston suunnittelu hydrometallurgisiin sovelluksiin

Työn tarkoituksena oli suunnitella, ohjelmoida ja koekäyttää SMB-laitteisto (Simulated Moving Bed) hydrometallurgisiin erotuksiin. Simuloitu liikkuvapeti saadaan aikaan vaihtamalla sisään- ja ulostuloporttien paikkaa nestevirran suuntaan. Tällöin aikaansaadaan kiintoaineen vastavirtaus minkä johdosta erotustehokkuus kasvaa. Komponenttien retentiotaipumuseroista johtuen komponentit liikkuvat eri nopeuksilla kolonnijärjestelmässä. Enemmän pidättäytyvät komponentit liikkuvat nestevirtaa vastaan ja vähemmän pidättäytyvät komponentit nestevirran mukana. Hydrometallurgiassa vastavirtauksen käyttöä ei ole tieteellisissä julkaisuissa käsitelty laajalti ja saatavilla oleva informaatio onkin kaupallisten yritysten tuottamaa. Hydrometallurgiassa vastavirtausta käyttävissä ioninvaihtolaitteistoissa hyödynnetään irrallisia regenerointivyöhykkeitä. Venttiilijärjestelmän osalta päädyttiin ratkaisuun jossa käytetään yhtä kiertoventtiiliä kullekin virralle, minkä lisäksi kolonnien väleillä käytetään solenoidiventtiiliä. Tämä järjestelmä mahdollistaa yleisimpien SMB-menetelmien käytön mukaan lukien irralliset vyöhykkeet. Laitteiston ohjauksesta vastaa LabVIEW 2010:llä ohjelmoitu ohjelmisto, joka sisältää kaikkien tarvittavien laitteiden ohjausrutiinit. Se mahdollistaa venttiilien synkroniset ja epäsynkroniset vaihdot. Laitteiston puhdistusta varten on ohjelmistoon rakennettu oma rutiini venttiilejä varten. Pumppujen osalta ohjelmisto mahdollistaa vakiovirtauksen sekä lineaaristen ja porrasmuotoisten gradienttien käytön. Ongelmatilanteita varten ohjelmisto valvoo pumppujen ja venttiilien toimintaa ja pysäyttää laitteiston tarvittaessa. Koekäytön avulla pystyttiin todentamaan laitteiston toimivuus.

Design of marine generators for alternative diesel-electric power systems

This study compares different electric propulsion systems. Results of the analysis of all the advantages and disadvantages of the different propulsion systems are given. This thesis estimates possibilities to apply different diesel-electric propulsion concepts for different vessel types. Small and medium size vessel’s power ranges are studied. The optimal delivery system is chosen. This choice is made on the base of detailed study of the concepts, electrical equipment market and comparison of mass, volume and efficiency parameters. In this thesis three marine generators are designed. They are: salient pole synchronous generator and two permanent magnet synchronous generators. Their electrical, dimensional, cost and efficiency parameters are compared. To understand all the benefits diagrams with these parameters are prepared. Possible benefits and money savings are estimated. As the result the advantages, disadvantages and boundary conditions for the permanent magnet synchronous generator application in marine electric-power systems are found out.

Laakerivirrat kestomagneettitahtikoneissa

Diplomityössä on esitelty ja tutkittu laakerivirtailmiötä sähkökoneissa. Työn pääpaino on suurissa kestomagneettitahtikoneissa, joissa niin sanotut kiertävät laakerivirrat ovat dominoivia. Työssä on lisäksi tarkasteltu staattorin segmentoinnin aiheuttamia matalataajuisia kiertovirtoja. Laakerivirran ja akselijännitteen ehkäisyyn on esitetty sekä testattu mahdollisia ratkaisuja.

Field Weakening, Parameters and Operation Range of the Permanent Magnet Traction Motors

The main focus of this thesis is to define the field weakening point of permanent magnet synchronous machine with embedded magnets in traction applications. Along with the thesis a modelling program is made to help the designer to define the field weakening point in practical applications. The thesis utilizes the equations based on the current angle. These equations can be derived from the vector diagram of permanent magnet synchronous machine. The design parameters of the machine are: The maximum rotational speed, saliency ratio, maximum induced voltage and characteristic current. The main result of the thesis is finding out the rated rotational speed, from which the field weakening starts. The action of the machine is estimated at a wide speed range and the changes of machine parameters are examined.

Design Aspects of Megawatt-Range Direct-Driven Permanent MagnetWind Generators

Direct-driven permanent magnet synchronous generator is one of the most promising topologies for megawatt-range wind power applications. The rotational speed of the direct-driven generator is very low compared with the traditional electrical machines. The low rotational speed requires high torque to produce megawatt-range power. The special features of the direct-driven generators caused by the low speed and high torque are discussed in this doctoral thesis. Low speed and high torque set high demands on the torque quality. The cogging torque and the load torque ripple must be as low as possible to prevent mechanical failures. In this doctoral thesis, various methods to improve the torque quality are compared with each other. The rotor surface shaping, magnet skew, magnet shaping, and the asymmetrical placement of magnets and stator slots are studied not only by means of torque quality, but also the effects on the electromagnetic performance and manufacturability of the machine are discussed. The heat transfer of the direct-driven generator must be designed to handle the copper losses of the stator winding carrying high current density and to keep the temperature of the magnets low enough. The cooling system of the direct-driven generator applying the doubly radial air cooling with numerous radial cooling ducts was modeled with a lumped-parameter-based thermal network. The performance of the cooling system was discussed during the steady and transient states. The effect of the number and width of radial cooling ducts was explored. The large number of radial cooling ducts drastically increases the impact of the stack end area effects, because the stator stack consists of numerous substacks. The effects of the radial cooling ducts on the effective axial length of the machine were studied by analyzing the crosssection of the machine in the axial direction. The method to compensate the magnet end area leakage was considered. The effect of the cooling ducts and the stack end area effects on the no-load voltages and inductances of the machine were explored by using numerical analysis tools based on the three-dimensional finite element method. The electrical efficiency of the permanent magnet machine with different control methods was estimated analytically over the whole speed and torque range. The electrical efficiencies achieved with the most common control methods were compared with each other. The stator voltage increase caused by the armature reaction was analyzed. The effect of inductance saturation as a function of load current was implemented to the analytical efficiency calculation.

FLOWERING AND POLLINATORS OF THREE DISTYLOUS SPECIES OF Psychotria (Rubiaceae) CO-OCCURRING IN THE BRAZILIAN ATLANTIC FOREST1

ABSTRACT This study investigates the flowering and pollinators of the floral morphs of three co-occurring distylous species, Psychotria conjugens Müll, P. hastisepala Müll. Arg. and P. sessilis Vell., in two consecutive flowering seasons in an Atlantic Forest fragment in southeastern Brazil. The species have diurnal, cream-colored, tubular, nectariferous flowers and their flowering occurs in the rainy season, from September to April, with little or no overlapping between species, characterizing a staggered flowering. The flowering of the long-and short-styled floral morphs of each species was synchronous, but the number of open flowers per day per morph tended to vary in each flowering season. These numbers were higher in P. sessilis and P. conjugens and, probably, resulted in higher total numbers of visits on its flowers (up to 1084 visits in P. sessilis and 756 in P. conjugens), compared to that observed in P. hastisepala (up to 71). There was a higher frequency of visits to long-styled flowers of all species. The bee Ariphanarthra palpalis was a common pollinator to all species. This bee is native to Brazil, solitary, considered relatively rare and its host plants were unknown. Other native bees (Melipona spp.) also visited the flowers of the Psychotria species. The availability of flowers with similar floral features over eight months, the staggered flowering and common pollinators appear to be part of a strategy to attract floral visitors, minimizing the competition for pollinators and then favoring the legitimate pollination of these plants.

Observations on the Pharmacokinetics and Pharmacodynamics of Dexmedetomidine. Clinical Studies on Healthy Volunteers and Intensive Care Patients

Patients treated in intensive care units require sedation and analgesia. However, sedative drugs also have potential adverse effects, and there is no single ideal sedativeanalgesic drug for these patients. Dexmedetomidine is an apha2-adrenoceptor agonist licenced for sedation of intensive care patients and patients undergoing surgery and other invasive procedures. Several routes of parenteral administration (intravenous, intramuscular, subcutaneous and intranasal) have been utilized. In the present series of studies, the pharmacokinetics and pharmacodynamics of intranasally administered dexmedetomidine as well as the gastrointestinal effects of intravenous dexmedetomidine were determined in healthy volunteers. Pharmacokinetics of dexmedetomidine during long lasting, high-dose infusions were characterized in intensive care patients. The bioavailability of intranasal dexmedetomidine was relatively good (65%), but interindividual variation was large. Dexmedetomidine significantly inhibited gastric emptying and gastrointestinal transit. In intensive care patients, the elimination half-life of dexmedetomidine was somewhat longer than reported for infusions of shorter duration and in less ill patients or healthy volunteers. Dexmedetomidine appeared to have linear pharmacokinetics up to the studied dose rate of 2.5 μg/kg/h. Dexmedetomidine clearance was decreasing with age and its volume of distribution was increased in hypoalbuminaemic patients, resulting in a longer elimination half-life and context-sensitive half-time. Intranasally administered dexmedetomidine was efficacious and well tolerated, making it appropriate for clinical situations requiring light sedation. The clinical significance of the gastrointestinal inhibitory effects of dexmedetomidine should be further evaluated in intensive care patients. The possibility of potentially altered potency and effect duration should be taken into account when administering dexmedetomidine to elderly or hypoalbuminaemic patients.

Leiomioma do esôfago removido por videolaparoscopia

This report describes a leiomyoma of the inferior third section of the esophagus removed during laparoscopic cholecystectomy. The patient is a woman 55-years-age, carrying esophageal myoma of 40 mm in diameter wide, situated in the posterior wall of the lower esophagus. Indications for surgery were based mainly on the growth of the mass (6 mm when discovered 7 years previously, increased to 40 mm). Recently the patient returned suffering from pain, which could be attributed to his litiasic cholecystopaty. A small degree of low disphagia could also be observed. Radiologic imaging, direct endoscopic examination and endoscopic ultrasound showed that the mioma protruded on to the oesophagic lumen, discreetly diminishing there. A laparoscopic esophageal myomectomy was indicated at the same session of the laparoscopic cholecystectomy. Once the pneunoperitoneum was installed, five ports were placed as if for a hiatus hernia surgery. The cholecystectomy was uneventful. Next, an esophagoscopy was performed so as to determine the precise area covering the base of the tumour; at the right-lateral site. Longitudinal and circular fibres of the esophagus was severed over the lesion and the enucleation of the tumour was performed alternating the monopolar dissection, bipolar and hidrodisection. Control-endoscopy was carried out to verify mucosa integrity. Four suture points with poliglactine 3-0 string so as to close the musculature followed this. One suture was placed in for diminution of the size of the esophagean hiatus. Total time of intervention: two hours (30m for the cholecystectomy and one hour and thirty minutes for the myomectomy). Postoperative period: uneventful. Disappearance of the disphagia was observed. Radiologic transit control with water-soluble contrast at 4th post-operative day: good passage. Diagnosis from laboratory of pathology: conjunctive tumour formed by muscle non-striated cells: leiomyoma. The patient was re-examined on the two-month postoperative follow-up. General conditions were good and there were no complain of dysphagia. Neither there were any symptoms of gastro-esophageal reflux.

Anastomose duodenoduodenal na pancreatoduodenectomia por pancreatite crônica

Literature has been showing a tendency of reducing the limits of Whipple's resection. The main technical advance was the pylorus preserving resection, technique proposed by Traverso and Longmire in 1978. The pancreticoduodenectomy for chronic pancreatitis, is probably the best opportunity to apply this type of procedure. In these specific patients, the author preserved the pylorus and the third portion of the duodenum. The gastrointestinal transit was reconstructed by the duodenumduodenal anastomosis and the bile duct and the pancreas were drained in a Roux-en-way loop . Follow-up showed no important complication, with no problems related to gastric emptying and without pain.

Tumor do apêndice vermiforme

Appendiceal tumors are rare and usually presented as acute appendicitis. They are incidentally discovered at an emergency surgery, in which case the decision-making is very difficult. The purpose of this report is discuss to the most appropriate management for appendiceal tumors. A retrospective analysis of one case treated at HU-UEL was undertaken and the literature was reviewed. The conclusion is that frozen section should be done whenever the appendiceal findings are atypical. For appendiceal carcinoids greater than 2 cm and adenocarcinomas, a right hemicolectomy is recommended. Appendectomy is apropriate for patients whose carcinoid tumors are 1 cm in diameter or less and for carcinoid tumors between 1 cm and 2 cm without extensive lymphatic permeation and mesenteric invasion. Every case should be searched for synchronous tumors.

Megacólon chagásico associado a pneumatose cística difusa do delgado e úlcera péptica duodenal

Diffuse intestinal pneumatosis appears as gaseous cysts in the intestinal wall in the submucosal layer or, more frequently, sub-serous layer. It affects more the jejunum than the ileum, can be diffuse and may extend into the colon. It's diagnosis is established during a small bowel transit examination, necropsy examination or during surgical exploration of the peritoneal cavity.

Building object-oriented software with the D-Bus messaging system

Object-oriented programming is a widely adopted paradigm for desktop software development. This paradigm partitions software into separate entities, objects, which consist of data and related procedures used to modify and inspect it. The paradigm has evolved during the last few decades to emphasize decoupling between object implementations, via means such as explicit interface inheritance and event-based implicit invocation. Inter-process communication (IPC) technologies allow applications to interact with each other. This enables making software distributed across multiple processes, resulting in a modular architecture with benefits in resource sharing, robustness, code reuse and security. The support for object-oriented programming concepts varies between IPC systems. This thesis is focused on the D-Bus system, which has recently gained a lot of users, but is still scantily researched. D-Bus has support for asynchronous remote procedure calls with return values and a content-based publish/subscribe event delivery mechanism. In this thesis, several patterns for method invocation in D-Bus and similar systems are compared. The patterns that simulate synchronous local calls are shown to be dangerous. Later, we present a state-caching proxy construct, which avoids the complexity of properly asynchronous calls for object inspection. The proxy and certain supplementary constructs are presented conceptually as generic object-oriented design patterns. The e ect of these patterns on non-functional qualities of software, such as complexity, performance and power consumption, is reasoned about based on the properties of the D-Bus system. The use of the patterns reduces complexity, but maintains the other qualities at a good level. Finally, we present currently existing means of specifying D-Bus object interfaces for the purposes of code and documentation generation. The interface description language used by the Telepathy modular IM/VoIP framework is found to be an useful extension of the basic D-Bus introspection format.

Advanced welding technologies used for arctic metal structures

Rapid depletion of easy-to-access fossil fuel, predominantly, oil and gas resources has now necessitated increase in need to develop new oil and gas sources in ever more remote and hostile environments. This is necessary in order to explore more oil and gas resources to meet rapidly rising long-term energy demand in the world, both at present and in the nearest future. Arctic is one of these harsh environments, where enormous oil and gas resources are available, containing about 20% of the world total oil and gas, but the environmental conditions are very harsh and hostile. However, virtually all the facilities required for the exploration and development of this new energy source are constructed with metals as well as their alloys and are predominantly joined together by welding processes and technologies. Meanwhile, due to entirely different environment from the usual moderate temperate region, conventional welding technologies, common metals and their alloys cannot be applied as this Arctic environment demand metals structures with very high toughness and strength properties under extremely low temperature. This is due to the fact that metals transit from ductility to brittleness as the temperature moves toward extreme negative values. Hence, this research work investigates and presents the advanced welding technologies applicable to Arctic metal structures which can give satisfactory weldments under active Arctic service conditions. .

Project Master Document adaption in order fulfillment process

This thesis discusses adaption of new project management tool at ABB Oy Motors and Generators business unit, Synchronous Machines profit centre. Thesis studies project modeling in general and buries in the Gate Model used at ABB Synchronous Machines. It is essential to understand Gate Model because this new project management tool, called Project Master Document, is created on the base of the existing project model. Thesis also analyzes goals and structure of Project Master Document in order to ease implementation of this new tool. Project Master Document aims to improved customer order fulfillment by clearing order handover interface. Office process, especially responsibilities and target dates, become also clearer after Master Document implementation. The document is built to be frame for whole order fulfillment process including check points for each gate of project model and updated memos from all project meetings. Furthermore, project progress will be clearly stated by status markings and visualized with colors.