Functional cellulose microspheres for pharmaceutical applications

Dissolving cellulose is the first main step in preparing novel cellulosicmaterials. Since cellulosic fibres cannot be easily dissolved in water-based solvents, fibres were pretreated with ethanol-acid solution prior to the dissolution. Solubility and changes on the surface of the fibres were studied with microscopy and capillary viscometry. After the treatment, the cellulose fibres were soluble in alkaline urea-water solvent. The nature of this viscous solution was studied rheologically. Cellulose microspheres were prepared by extruding the alkaline cellulose solution through the needle into an acidic medium. By altering the temperature and acidity of the mediumit was possible to adjust the specific surface area and pore sizes of themicrospheres. A typical skin-core structure was found in all samples. Microspheres were oxidised in order to introduce anionic carboxylic acid groups (AGs). Anionic microspheres are more hydrophilic; their water-uptake increased 25 times after oxidation and they could swell almost to their original state (88%) after drying and shrinking. Swelling was studied in simulated physiological environments, corresponding to stomach acid and intestines (pH 1.2-7.4). Oxidised microspheres were used as a drug carriers. They demonstrated a highmass uniformity, which would enable their use for personalised dosing among different patients, including children. The drug was solidified in microspheres in amorphous form. This enhanced solubility and could be used for more challenging drugs with poor solubility. The pores of themicrospheres also remained open after the drug was loaded and they were dried. Regardless of the swelling, the drug was released at a constant rate in all environments.

Spatial modeling techniques for mapping and characterization of acid sulfate soils

Acid sulfate (a.s.) soils constitute a major environmental issue. Severe ecological damage results from the considerable amounts of acidity and metals leached by these soils in the recipient watercourses. As even small hot spots may affect large areas of coastal waters, mapping represents a fundamental step in the management and mitigation of a.s. soil environmental risks (i.e. to target strategic areas). Traditional mapping in the field is time-consuming and therefore expensive. Additional more cost-effective techniques have, thus, to be developed in order to narrow down and define in detail the areas of interest. The primary aim of this thesis was to assess different spatial modeling techniques for a.s. soil mapping, and the characterization of soil properties relevant for a.s. soil environmental risk management, using all available data: soil and water samples, as well as datalayers (e.g. geological and geophysical). Different spatial modeling techniques were applied at catchment or regional scale. Two artificial neural networks were assessed on the Sirppujoki River catchment (c. 440 km2) located in southwestern Finland, while fuzzy logic was assessed on several areas along the Finnish coast. Quaternary geology, aerogeophysics and slope data (derived from a digital elevation model) were utilized as evidential datalayers. The methods also required the use of point datasets (i.e. soil profiles corresponding to known a.s. or non-a.s. soil occurrences) for training and/or validation within the modeling processes. Applying these methods, various maps were generated: probability maps for a.s. soil occurrence, as well as predictive maps for different soil properties (sulfur content, organic matter content and critical sulfide depth). The two assessed artificial neural networks (ANNs) demonstrated good classification abilities for a.s. soil probability mapping at catchment scale. Slightly better results were achieved using a Radial Basis Function (RBF) -based ANN than a Radial Basis Functional Link Net (RBFLN) method, narrowing down more accurately the most probable areas for a.s. soil occurrence and defining more properly the least probable areas. The RBF-based ANN also demonstrated promising results for the characterization of different soil properties in the most probable a.s. soil areas at catchment scale. Since a.s. soil areas constitute highly productive lands for agricultural purpose, the combination of a probability map with more specific soil property predictive maps offers a valuable toolset to more precisely target strategic areas for subsequent environmental risk management. Notably, the use of laser scanning (i.e. Light Detection And Ranging, LiDAR) data enabled a more precise definition of a.s. soil probability areas, as well as the soil property modeling classes for sulfur content and the critical sulfide depth. Given suitable training/validation points, ANNs can be trained to yield a more precise modeling of the occurrence of a.s. soils and their properties. By contrast, fuzzy logic represents a simple, fast and objective alternative to carry out preliminary surveys, at catchment or regional scale, in areas offering a limited amount of data. This method enables delimiting and prioritizing the most probable areas for a.s soil occurrence, which can be particularly useful in the field. Being easily transferable from area to area, fuzzy logic modeling can be carried out at regional scale. Mapping at this scale would be extremely time-consuming through manual assessment. The use of spatial modeling techniques enables the creation of valid and comparable maps, which represents an important development within the a.s. soil mapping process. The a.s. soil mapping was also assessed using water chemistry data for 24 different catchments along the Finnish coast (in all, covering c. 21,300 km2) which were mapped with different methods (i.e. conventional mapping, fuzzy logic and an artificial neural network). Two a.s. soil related indicators measured in the river water (sulfate content and sulfate/chloride ratio) were compared to the extent of the most probable areas for a.s. soils in the surveyed catchments. High sulfate contents and sulfate/chloride ratios measured in most of the rivers demonstrated the presence of a.s. soils in the corresponding catchments. The calculated extent of the most probable a.s. soil areas is supported by independent data on water chemistry, suggesting that the a.s. soil probability maps created with different methods are reliable and comparable.

Morphological and functional alterations of the intestine of rats with iron-deficiency anemia

The present study was designed to assess the intestinal absorption of D-xylose and jejunal morphometry in rats with iron-deficiency anemia. Male Wistar rats were randomly divided into a control group (diet containing 50 mg Fe/kg, N = 12) and an anemic group (diet containing <5 mg Fe/kg, N = 12). The animals were housed in individual metabolic cages and deionized water and diet were provided ad libitum for 6 weeks. Hemoglobin and hematocrit were determined at 0, 2, 4, and 6 weeks. At the end of the study the rats were submitted to a D-xylose absorption test (50 mg/100 g body weight) and sacrificed and a jejunal specimen was obtained for morphometric study. At the end of the study the hemoglobin and hematocrit of the anemic rats (8.7 ± 0.9 g/dl and 34.1 ± 2.9%, respectively) were significantly (P < 0.05) lower than those of the controls (13.9 ± 1.4 g/dl and 47.1 ± 1.5%, respectively). There was no statistical difference in D-xylose absorption between the anemic (46.5 ± 7.4%) and control (43.4 ± 9.0%) groups. The anemic animals presented statistically greater villus height (445.3 ± 36.8 µm), mucosal thickness (614.3 ± 56.3 µm) and epithelial surface (5063.0 ± 658.6 µm) than control (371.8 ± 34.3, 526.7 ± 62.3 and 4401.2 ± 704.4 µm, respectively; P < 0.05). The increase in jejunum villus height, mucosal thickness and epithelial surface in rats with iron-deficiency anemia suggests a compensatory intestinal mechanism to increase intestinal iron absorption.

Protein-mediated surface structuring in biomembranes

The lipids and proteins of biomembranes exhibit highly dissimilar conformations, geometrical shapes, amphipathicity, and thermodynamic properties which constrain their two-dimensional molecular packing, electrostatics, and interaction preferences. This causes inevitable development of large local tensions that frequently relax into phase or compositional immiscibility along lateral and transverse planes of the membrane. On the other hand, these effects constitute the very codes that mediate molecular and structural changes determining and controlling the possibilities for enzymatic activity, apposition and recombination in biomembranes. The presence of proteins constitutes a major perturbing factor for the membrane sculpturing both in terms of its surface topography and dynamics. We will focus on some results from our group within this context and summarize some recent evidence for the active involvement of extrinsic (myelin basic protein), integral (Folch-Lees proteolipid protein) and amphitropic (c-Fos and c-Jun) proteins, as well as a membrane-active amphitropic phosphohydrolytic enzyme (neutral sphingomyelinase), in the process of lateral segregation and dynamics of phase domains, sculpturing of the surface topography, and the bi-directional modulation of the membrane biochemical reactivity.

Bacterial community structure and petroleum hydrocarbon degradation in the Baltic Sea

The Baltic Sea is unique by its biological, geochemical and physical features. The number of species of larger organisms is small and the species composition is distinctive. On the contrary microbial communities are diverse. Because of the low salinity levels, bacterial communities differ from the ones in the oceans. Knowing the structure of these communities better and how they response to different environmental conditions helps us to estimate how different factors affect the balance and function of the Baltic Sea ecosystem. Bacteria are the key players when it comes to natural biogeochemical processes and human-induced phenomena like eutrophication, oil spills or disposal of other harmful substances to the sea ecosystem. In this thesis, bacterial community structure in the sea surface microlayer and subsurface water of the Archipelago Sea were compared. In addition, the effect of diatom derived polyunsaturated aldehydes on bacterial community structure was studied by a mesocosm experiment. Diesel, crude oil and polycyclic aromatic hydrocarbon degradation capacity of the Baltic Sea bacteria was studied in smaller scale microcosm experiments. In diesel oil experiments bacteria from water phase of the Archipelago Sea was studied. Sediment and iron manganese concretions collected from the Gulf of Finland were used in the crude oil and polycyclic aromatic hydrocarbon experiments. The amount of polycyclic aromatic hydrocarbon degradation genes was measured in all of the oil degradation experiments. The results show how differences in bacterial community structure can be seen in the sea surface when compared to the subsurface waters. The mesocosm experiment demonstrated how diatom-bacteria interactions depend on other factors than diatom derived polyunsaturated aldehydes, which do not seem to have an effect on the bacterial community structure as has been suggested in earlier studies. The dominant bacterial groups in the diesel microcosms differed in samples taken from a pristine site when compared to a site with previous oil exposure in the Archipelago Sea area. Results of the study with sediment and iron-manganese concretions indicate that there are diverse bacterial communities, typical to each bottom type, inhabiting the bottoms of the Gulf of Finland capable to degrade oil and polycyclic aromatic hydrocarbon compounds.  

Geochemistry and water quality of Lake Qarun, Egypt

Water geochemistry is a very important tool for studying the water quality in a given area. Geology and climate are the major natural factors controlling the chemistry of most natural waters. Anthropogenic impacts are the secondary sources of contamination in natural waters. This study presents the first integrative approach to the geochemistry and water quality of surface waters and Lake Qarun in the Fayoum catchment, Egypt. Moreover, geochemical modeling of Lake Qarun was firstly presented. The Nile River is the main source of water to the Fayoum watershed. To investigate the quality and geochemistry of this water, water samples from irrigation canals, drains and Lake Qarun were collected during the period 2010‒2013 from the whole Fayoum drainage basin to address the major processes and factors governing the evolution of water chemistry in the investigation area. About 34 physicochemical quality parameters, including major ions, oxygen isotopes, trace elements, nutrients and microbiological parameters were investigated in the water samples. Multivariable statistical analysis was used to interpret the interrelationship between the different studied parameters. Geochemical modeling of Lake Qarun was carried out using Hardie and Eugster’s evolutionary model and a model simulated by PHREEQC software. The crystallization sequence during evaporation of Lake Qarun brine was also studied using a Jänecke phase diagram involving the system Na‒K‒Mg‒ Cl‒SO4‒H2O. The results show that the chemistry of surface water in the Fayoum catchment evolves from Ca- Mg-HCO3 at the head waters to Ca‒Mg‒Cl‒SO4 and eventually to Na‒Cl downstream and at Lake Qarun. The main processes behind the high levels of Na, SO4 and Cl in downstream waters and in Lake Qarun are dissolution of evaporites from Fayoum soils followed by evapoconcentration. This was confirmed by binary plots between the different ions, Piper plot, Gibb’s plot and δ18O results. The modeled data proved that Lake Qarun brine evolves from drainage waters via an evaporation‒crystallization process. Through the precipitation of calcite and gypsum, the solution should reach the final composition "Na–Mg–SO4–Cl". As simulated by PHREEQC, further evaporation of lake brine can drive halite to precipitate in the final stages of evaporation. Significantly, the crystallization sequence during evaporation of the lake brine at the concentration ponds of the Egyptian Salts and Minerals Company (EMISAL) reflected the findings from both Hardie and Eugster’s evolutionary model and the PHREEQC simulated model. After crystallization of halite at the EMISAL ponds, the crystallization sequence during evaporation of the residual brine (bittern) was investigated using a Jänecke phase diagram at 35 °C. This diagram was more useful than PHREEQC for predicting the evaporation path especially in the case of this highly concentrated brine (bittern). The predicted crystallization path using a Jänecke phase diagram at 35 °C showed that halite, hexahydrite, kainite and kieserite should appear during bittern evaporation. Yet the actual crystallized mineral salts were only halite and hexahydrite. The absence of kainite was due to its metastability while the absence of kieserite was due to opposed relative humidity. The presence of a specific MgSO4.nH2O phase in ancient evaporite deposits can be used as a paleoclimatic indicator. Evaluation of surface water quality for agricultural purposes shows that some irrigation waters and all drainage waters have high salinities and therefore cannot be used for irrigation. Waters from irrigation canals used as a drinking water supply show higher concentrations of Al and suffer from high levels of total coliform (TC), fecal coliform (FC) and fecal streptococcus (FS). These waters cannot be used for drinking or agricultural purposes without treatment, because of their high health risk. Therefore it is crucial that environmental protection agencies and the media increase public awareness of this issue, especially in rural areas.

Overexpression of hsa-miR-125b during osteoblastic differentiation does not influence levels of Runx2, osteopontin, and ALPL gene expression

Multipotent mesenchymal stromal cells (MSCs) were first isolated from bone marrow and then from various adult tissues including placenta, cord blood, deciduous teeth, and amniotic fluid. MSCs are defined or characterized by their ability to adhere to plastic, to express specific surface antigens, and to differentiate into osteogenic, chondrogenic, adipogenic, and myogenic lineages. Although the molecular mechanisms that control MSC proliferation and differentiation are not well understood, the involvement of microRNAs has been reported. In the present study, we investigated the role of miR-125b during osteoblastic differentiation in humans. We found that miR-125b increased during osteoblastic differentiation, as well as Runx2 and ALPL genes. To study whether the gain or loss of miR-125b function influenced osteoblastic differentiation, we transfected MSCs with pre-miR-125b or anti-miR-125b and cultured the transfected cells in an osteoblastic differentiation medium. After transfection, no change was observed in osteoblastic differentiation, and Runx2, OPN, and ALPL gene expression were not changed. These results suggest that the gain or loss of miR-125b function does not influence levels of Runx2, OPN, and ALPL during osteoblastic differentiation.

Modifications in the chemical compounds and sensorial attributes of Engraulis anchoita fillet during marinating process

Marinated fish are fish products preserved by the combined action of salt and organic acids. The objective of this work was to analyze the variations in the chemical compounds of anchovy fillets that give them sensorial characteristics during the marinating process of Engraulis anchoita. The protein content decreased slightly and the TVB-N level decreased significantly in both the brining and marinating stages. In the marinating stage an increase in the total free aminoacids was observed. The NBV level in the brining and marinating solutions increased during these stages due to the solubilization of the non-protein nitrogenous compounds and the degradation of some protein compounds.The decrease of the contents of protein and TVB-N, and the increase of the acidity and the free aminoacids content during the marinating process give the marinated fillets the characteristic texture and aroma.

Monolithic zirconium dioxide as a full contour restorative material: With special emphasis on the optical and mechanical properties

Full contour monolithic zirconia restorations have shown an increased popularity in the dental field over the recent years, owing to its mechanical and acceptable optical properties. However, many features of the restoration are yet to be researched and supported by clinical studies to confirm its place among the other indirect restorative materials This series of in vitro studies aimed at evaluating and comparing the optical and mechanical properties, light cure irradiance, and cement polymerization of multiple monolithic zirconia material at variable thicknesses, environments, treatments, and stabilization. Five different monolithic zirconia materials, four of which were partially stabilized and one fully stabilized were investigated. The optical properties in terms of surface gloss, translucency parameter, and contrast ratio were determined via a reflection spectrophotometer at variable thicknesses, coloring, sintering method, and after immersion in an acidic environment. Light cure irradiance and radiant exposure were quantified through the specimens at variable thicknesses and the degree of conversion of two dual-cure cements was determined via Fourier Transform Infrared spectroscopy. Bi-axial flexural strength was evaluated to compare between the partially and fully stabilized zirconia prepared using different coloring and sintering methods. Surface characterization was performed using a scanning electron microscope and a spinning disk confocal microscope. The surface gloss and translucency of the zirconia investigated were brand and thickness dependent with the translucency values decreasing as the thickness increased. Staining decreased the translucency of the zirconia and enhanced surface gloss as well as the flexural strength of the fully stabilized zirconia but had no effect on partially stabilized zirconia. Immersion in a corrosive acid increased surface gloss and decreased the translucency of some zirconia brands. Zirconia thickness was inversely related to the amount of light irradiance, radiant exposure, and degree of monomer conversion. Type of sintering furnace had no effect on the optical and mechanical properties of zirconia. Monolithic zirconia maybe classified as a semi-translucent material that is well influenced by the thickness, limiting its use in the esthetic zones. Conventional acid-base reaction, autopolymerizing and dual-cure cements are recommended for its cementation. Its desirable mechanical properties give it a high potential as a restoration for posterior teeth. However, close monitoring with controlled clinical studies must be determined before any definite clinical recommendations can be drawn.

Discrimination of Brazilian red wines according to the viticultural region, varietal, and winery origin

This work evaluated the physicochemical composition of 171 red Brazilian wines from the 2006 vintage, which were represented by 21 varietals. These wines were produced by 58 Brazilian wineries in different regions of the country, with latitudes varying from 9º to 31º South. Physicochemical wine analysis was performed in the same year and discrimination in the viticultural regions, varietal wines, and wineries was performed by means of the principal component analysis (PCA). The main results show that wines from São Joaquim had higher values of A420, A520, A620, color intensity, total phenolic compounds, anthocyanins, and dry extracts, while those from Toledo had lower values of these variables; those from Vale do São Francisco had higher values of potassium, pH, density, and volatile acidity; from Serra do Nordeste A, they had higher titratable acidity; and from Planalto Superior B, higher hue. Regarding the varietal wines, PCA mainly discriminated the wines produced from the varieties Ancellotta, Teroldego, Egiodola, Refosco, Marselan, Cabernet Sauvignon, Pinotage, Pinot Noir, Malbec, Arinarnoa, Barbera, and Alfrocheiro. In relation to wineries, twenty two of them were discriminated by their higher values of some variables, i.e., three were characterized by color intensity; three by hue; eight by alcohol content; six by potassium, dry extract, density, and pH; and two by titratablel acidity.

Foresight of physical-chemical characteristics of apple juice blends appointed to sparkling drink elaboration

The purpose of this research was to combine the use of the component blend design to the response surface methodology, in order to foresee the effect of ternary apple juice blends (Catarina, Granny Smith and Pink Lady cultivars) on the physical-chemical characteristics of musts appointed to sparkling drink elaboration. Twelve mixes were made (three individual samples, three binary mixes and six ternary mixes), analyzed on the content of total reducing sugars, total titratable acidity and phenolic compounds; and adjusted, respectively, to the linear, quadratic and special cubic models. The results were organized in ternary charts of surface response and, from the overlap of these charts, it was determined a viable region which delimited the range of apple juice compositions that make musts physically and chemically suitable to sparkling drink elaboration. To represent the various possible combinations, the central point of the triangular area of the viable region was calculated and, this point, which represents the proportions of 23.22% of Catarina, 66.23% of Granny Smith and 10.55% of Pink Lady cultivars, was chosen to constitute the formulation of the must to be used in the elaboration of apple sparkling drinks.

Chemical and physicochemical characteristics changes during passion fruit juice processing

Passion fruit is widely consumed due to its pleasant flavour and aroma acidity, and it is considered very important a source of minerals and vitamins. It is used in many products such as ice-cream, mousses and, especially, juices. However, the processing of passion fruit juice may modify the composition and biodisponibility of the bioactive compounds. Investigations of the effects of processing on nutritional components in tropical juices are scarce. Frequently, only losses of vitamin C are evaluated. The objective of this paper is to investigate how some operations of passion fruit juice processing (formulation/homogeneization/thermal treatment) affect this product's chemical and physicochemical characteristics. The results showed that the chemical and physicochemical characteristics are little affected by the processing although a reduction in vitamin C contents and anthocyanin, large quantities of carotenoids was verified even after the pasteurization stage.

Characterization of maturity and quality of Brazilian apirenic grapes in the São Francisco river Valley

The objective of this study was to characterize and correlate maturity and quality of the first varieties of Brazilian seedless grapes 'BRS Clara', 'BRS Linda', 'BRS Morena', and 'Advanced Selection 8' compared with the American variety 'Crimson Seedless' in compliance with the Brazilian Normative/2002 and export standards Advanced Selection 8' is dark reddish, has large clusters, and is a very large ellipsoid berry; 'BRS Morena' is black with medium sized clusters and large berry shaped as ellipsoid to globoid; 'BRS Linda' is light green and has large sized clusters; 'Crimson' is pink and has small clusters with berries varying from medium to large sizes and ellipsoid shaped; and 'BRS Clara' is green yellowish has medium sized clusters and small berry of elongated ellipsoid shape. All varieties evaluated meet the standard for domestic market established as berry size minimum diameter 12 mm. 'BRS Clara' does not meet the export requirements of diameter. Berries of the red grapes 'BRS Morena' and 'Crimson Seedless' are firmer. The pH, titratable acidity, and soluble solids meet the official standards. Larger clusters are less acidic and present higher soluble solids/titratable acidity ratios implying that they are the sweetest type when ripe.

Influence of the extraction method and storage time on the physicochemical properties and carotenoid levels of pequi (Caryocar brasiliense Camb.) oil

The objective of this study was to analyze the physicochemical properties and carotenoid levels of pequi oil obtained by different extraction methods and to evaluate the preservation of these properties and pigments during storage time. The pequi oil was obtained by solvent extraction, mechanical extraction, and hot water flotation. It was stored for over 180 days in an amber bottle at ambient conditions. Analyses for the determination of the acidity, peroxide, saponification and iodine values, coloration, total carotenoids, and β-carotene levels were conducted. The oil extraction with solvents produced the best yield and carotenoid levels. The oil obtained by mechanical extraction presented higher acidity (5.44 mg KOH.g-1) and peroxide values (1.07 mEq.kg-1). During the storage of pequi oil, there was an increase in the acidity and the peroxide values, darkening of the oil coloration, and a reduction of the carotenoid levels. Mechanical extraction is the less advantageous method for the conservation of the physicochemical properties and carotenoid levels in pequi oil.

Estimate of respiration rate and physicochemical changes of fresh-cut apples stored under different temperatures

In this study, the influence of storage temperature and passive modified packaging (PMP) on the respiration rate and physicochemical properties of fresh-cut Gala apples (Malus domestica B.) was investigated. The samples were packed in flexible multilayer bags and stored at 2 °C, 5 °C, and 7 °C for eleven days. Respiration rate as a function of CO2 and O2 concentrations was determined using gas chromatography. The inhibition parameters were estimated using a mathematical model based on Michaelis-Menten equation. The following physicochemical properties were evaluated: total soluble solids, pH, titratable acidity, and reducing sugars. At 2 °C, the maximum respiration rate was observed after 150 hours. At 5 °C and 7 °C the maximum respiration rates were observed after 100 and 50 hours of storage, respectively. The inhibition model results obtained showed a clear effect of CO2 on O2 consumption. The soluble solids decreased, although not significantly, during storage at the three temperatures studied. Reducing sugars and titratable acidity decreased during storage and the pH increased. These results indicate that the respiration rate influenced the physicochemical properties.