Direct visualization of collapse process of porphyrin monolayers and porphyrin exclusion for mixed monolayers at the air-water interface

The collapse process of porphyrin monolayers at the air-water interface was studied by Brewster angle microscopy and by compression-recompression isotherms. It was found that the start of collapse observed by BAM is accordant with that measured by compression-recompression isotherms. The behavior of mixed monolayers was studied also and the results showed that porphyrin islands were excluded from mixed monolayers at 35mN/m.

STUDY ON THE REDOX PROCESS OF BILIRUBIN AND BILIVERDIN AT PLATINUM-ELECTRODE BY IN-SITU SPECTROELECTROCHEMISTRY

The electrochemical redox behavior of bilirubin (BR IValpha), biliverdin (BV IValpha) and their oxidized product bile-purpurin (Bi-Pu) have been studied by in situ spectroelectrochemical techniques, which reveals that the transformation of BR IValpha [GRA

VALENCY AND ITS CHANGE PROCESS OF SAMARIUM ION IN SAMARIUM FLUORIDE SYSTEM

Nonstoichiometric series SmF(x) (2.0 less-than-or-equal-to x less-than-or-equal-to 3.0) have been synthesized by reduction of samarium trifluoride with hydrogen for several times, and the stoichiometric samarium difluoride has been obtained. The structure of nonstoichiometric samarium fluoride series and the valency of samarium ion are briefly discussed. The valent change process of samarium ion at high temperatures in different atmospheres is investigated.

DYNAMIC PROCESS OF VALENCE CHANGE OF EUROPIUM ION IN EUROPIUM DIFLUORIDE AT HIGH-TEMPERATURE

The dynamic process of the ionic valence changing from Eu~(2+) to Eu~(3+) in EuF_2 at high temperature has been investigated by ESCA, high,temperature X-ray diffraction, high temperature spectrum, high temperature magnetic Isusceptibility and Mssbauer spectrum. It has been shown that the formed Eu~(3+) exists in different compounds when EuF_2 is heated to high temperature in different atmospheres. In air, Eu~(3+) exists in the form of hexagonal EuOF, in nitrogen, in the form of orthogonal EuF_3 and non-hexa...

Rifting process and formation mechanisms of syn-rift stage prolongation in the deepwater basin, northern South China Sea

Based on the latest seismic and geological data, tectonic subsidence of three seismic lines in the deepwater area of Pearl River Mouth Basin (PRMB), the northern South China Sea (SCS), is calculated. The result shows that the rifting process of study area is different from the typical passive continental margin basin. Although the seafloor spreading of SCS initiated at 32 Ma, the tectonic subsidence rate does not decrease but increases instead, and then decreases at about 23 Ma, which indicates that the rifting continued after the onset of seafloor spreading until about 23 Ma. The formation thickness exhibits the same phenomenon, that is the syn-rift stage prolonged and the post-rift thermal subsidence delayed. The formation mechanisms are supposed to be three: (1) the lithospheric rigidity of the northern SCS is weak and its ductility is relatively strong, which delayed the strain relaxation resulting from the seafloor spreading; (2) the differential layered independent extension of the lithosphere may be one reason for the delay of post-rift stage; and (3) the southward transition of SCS spreading ridge during 24 to 21 Ma and the corresponding acceleration of seafloor spreading rate then triggered the initiation of large-scale thermal subsidence in the study area at about 23 Ma.

Vertical transferring process of rare elements in coral reef lagoons of Nansha Islands, South China Sea

The vertical fluxes and vertical transferring forms of 18 rare elements were studied for the first time in the coral reef ecosystem of Nansha Islands, South China Sea, by deploying sediment traps, The results showed that the vertical transferring flux of most of the measured rare elements in Yongshu lagoon were higher than that in Zhubi lagoon. The vertical transferring forms of rare elements were mainly in the carbonate form, but Ta, As, Th mainly in the ion-exchange form, Ag in iron-manganese oxide form and Sb in the organic matter + sulphide form. None of the 18 rare elements was transferred mainly in the form of detritus silicate to sea floor. This proved that rare elements originating from the earth's crust were redistributed in sinking particulates after they were brought into ocean. The relation between the fluxes and surface seawater temperature (STT) was also studied. The sensitivity of rare elements to SST was in order: Rb>V>As>Ti>U>Zn>Sb>Hf>Ag>Cs.

Hydrogen ion reduction in the process of iron rusting

Since the acceptance of the electrochemical rusting mechanism, oxygen reduction has been considered the main cathodic process, while H+ reduction has been overlooked for the past four decades because oxygen can be readily renewed due to the thin layer Of Solution film formed during atmospheric corrosion. This study shows that measurable hydrogen call be detected at the surface opposite to the corroding side of the specimen during wet-dry cycles, and a clear correlation exists between the quantities of hydrogen permeated through iron sheet and weight loss. Results Suggest the intrinsic importance of H+ reduction that merits further investigation. (c) 2004 Elsevier Ltd. All rights reserved.

Hydrogen entry into steel during atmospheric corrosion process

Hydrogen entry and permeation into iron were measured by an electrochemical method during atmospheric corrosion reaction. The hydrogen permeation was enhanced on passive films because the hydrogen adsorption increased by the hydrogen evolution mechanism which is different from that on a bear iron surface. The permeation rate during a wet and dry corrosion cycle showed a maximum in the drying process depending upon the surface pH and the corrosion potential. The pollutant such as Na2SO3 which decreases the pH and the corrosion potential causes an increase in the permeation rate. The mechanism of the change in the permeation rate during the wet and dry cycles is explained by the polarization diagram of the electrode covered by thin water layer. (c) 2005 Elsevier Ltd. All rights reserved.

Effect of Process Conditions on Microstructure and Corrosion Resistance of Cold-Sprayed Ti Coatings

Ti and Ti alloys can be applied to steels as a protective coating in view of its excellent resistance to corrosive environment. Cold spraying, as a new coating technique, has potential advantages in fabrication of Ti coating in comparison with conventional thermal spraying techniques. In this study, Ti coatings were prepared on carbon steel substrates by cold spraying via controlling the process conditions. The microstructure of coatings was observed by SEM. The porosity of coatings was estimated by image analysis and the bond strength was tested for comparison of the process conditions. Potentiodynamic polarization and open-circuit potential (OCP) measurements were performed to understand the corrosion behavior of the coatings. The SEM examination shows that the coatings become more compact with the increases of pressure and temperature of driving gas. The potentiodynamic polarization curves indicate that the coating which has lower porosity has lower corrosion current. The polarization and OCP measurement reveal that cold-sprayed Ti coating can provide favorable protection to carbon steel substrate. The polishing treatment of coating surface polishes the rough outer layer including the small pores as well as decreases the actual surface area of the coating, leading to the considerable improvement of corrosion resistance.

An integrated air-POM syngas/dimethyl ether process from natural gas

A Cu-Zn-Al methanol catalyst combined with HZSM-5 was used for dimethyl ether (DME) synthesis from a syngas containing nitrogen, which was produced by air-partial oxidation of methane (air-POM). Air-POM occurred at 850 degreesC, 0.8 MPa, CH4/air/H2O/CO2 ratio of 1/2.4/0.8/0.4 over a Ni-based catalyst modified by magnesia and lanthanum oxide with 96% CH4 conversion and constantly gave syngas with a H-2/CO ratio of 2/1 during a period of 450 h. The obtained N-2-containing syngas was used directly for DME synthesis. About 90% CO per-pass conversion, 78% DME selectivity and 70% DME yield could be achieved during 450 h stability testing under the pressure of 5.0 MPa. the temperature of 240 degreesC and the space velocity of 1000 h(-1). (C) 2002 Elsevier Science B. V. All rights reserved.