Confecção e caracterização físico-química de filmes compósitos autossustentáveis NaAlg-TiO2-WO3

A new self-sustainable film was prepared through the sol-gel modified method, previously employed in our research group; sodium alginate was used as the polymer matrix, along with plasticizer glycerol, doped with titanium dioxide (TiO2) and tungsten trioxide (WO3). By varying WO3 concentration (0,8, 1,6, 2,4 and 3,2 μmol) and keeping TiO2 concentration constant (059 mmol), it was possible to study the contribution of these oxides on the obtained films morphological and electrical properties. Self-sustainable films have analyzed by Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XDR), Scanning Electron Microscope (SEM), Energy Dispersive X-ray Spectroscopy (EDS) and Electrochemical Impedance Spectroscopy (EIS). By the IR specters, it was possible identify the TiO2, and posteriorly WO3, addition has provided dislocation of alginate characteristics bands to smaller vibrations frequencies indicating an electrostatic interaction between the oxides and the polymer matrix. Diffractograms show predominance of the amorphous phase in the films. SEM, along with EDX, analysis revealed self-sustainable films showed surface with no cracks and relative dispersion of the oxides throughout the polymer matrix. From Impedance analysis, it was observe increasing WO3 concentration to 2,4 μmol provided a reduction of films resistive properties and consequent improvement of conductive properties

Síntese, caracterização e estudo das propriedades magnéticas de ortoferritas de lantânio dopadas com manganês

Orthoferrites AFeO3 (A = rare earth) are an important class of perovskite oxides that exhibit weak ferromagnetism. These materials find numerous applications as chemical sensors, cathodes for fuel cells and catalysis, which make them interesting from the standpoint of science and technology. Their structural, electrical and magnetic properties are dependent on many factors such as the preparation method, heat treatment conditions, chemical composition and replacement of cations in sites A and/or B. In this paper, LaFe1-xMnxO3 (0 ≤ x ≤ 1) orthoferrites-type was prepared by Pechini method and Microwave-assisted combustion reaction in order to evaluate the influence of synthesis route on the formation of oxide, as well as the effect of parcial replacement of iron by manganese and heat treatment on the magnetic properties. The precursor powders were calcined at 700°C, 900°C, 1100°C and 1300°C for 4 hours and they were characterized by the techniques: Thermogravimetric analysis (TGA), X ray diffraction (XRD), Refinement by Rietveld method, Scanning electron microscopy (SEM), Reduction temperature programmed (RTP) and Magnetic hysteresis measurements performed at room temperature. According to the XRD patterns, the formation of perovskite phase with orthorhombic structure was observed for the systems where 0 ≤ x ≤ 0.5 and rhombohedral for x = 1. The results also showed a decrease of lattice parameters with the parcial replacement of iron by manganese and consequently a reduction in cell volume. The hysteresis curves exhibited weak ferromagnetism for the systems prepared by both synthesis methods. However, a dependence of magnetization as a function of dopant content was observed for samples produced by Pechini method. As for the systems prepared by combustion reaction, it was found that the secondary phases exert a strong influence on the magnetic behavior

Síntese, caracterização, propriedades e aplicação dos sistemas Mg- Al, Zn-Al e Mg-Fe

The Layered Double Hydroxides has become extremely promising materials due to its range of applications, easily obtained in the laboratory and reusability after calcination, so the knowledge regarding their properties is of utmost importance. In this study were synthesized layered double hydroxides of two systems, Mg-Al and Zn-Al, and such materials were analyzed with X-ray diffraction and, from these data, we determined the volume density, planar atomic density, size crystallite, lattice parameters, interplanar spacing and interlayer space available. Such materials were also subjected to thermogravimetric analysis reasons for heating 5, 10, 20 and 25 ° C / min to determine kinetic parameters for the formation of metaphases HTD and HTB based on theoretical models Ozawa, Flynn-Wall Starink and Model Free Kinetics. In addition, the layered double hydroxides synthesized in this working ratios were calcined heating 2.5 ° C / min and 20 ° C / min, and tested for adsorption of nitrate anion in aqueous solution batch system at time intervals 5 min, 15 min, 30 min, 1h, 2h and 4h. Such calcined materials were also subjected to exposure to the atmosphere and at intervals of 1 week, 2 weeks and 1 month were analyzed by infrared spectroscopy to study the kinetics of regeneration determining structural called "memory effect"

Uso de lodo de esgoto na reestruturação de solo degradado

O uso do solo nem sempre dá lugar a um novo sistema ecológico sustentável, seja de lavouras, seja de pastagens. Com isso, solos utilizados intensamente e de forma inadequada são levados à degradação. Nesse sentido, este trabalho teve como objetivo estudar a influência do lodo de esgoto na recuperação de propriedades físicas de um Latossolo Vermelho degradado, cultivado há 2,5 anos com eucalipto (Eucalyptus citriodora Hook) e braquiária (Brachiaria decumbens) no município de Selvíria, MS. O delineamento experimental utilizado foi em blocos casualizados com seis tratamentos e quatro repetições. Os tratamentos foram: 1-vegetação de Cerrado; 2-solo exposto sem tratamento para recuperação; 3-solo cultivado com eucalipto e braquiária sem uso do lodo de esgoto e adubação mineral; 4-solo cultivado com eucalipto e braquiária com adubação mineral; 5-solo cultivado com eucalipto e braquiária com uso de 30 Mg ha-1 de lodo de esgoto; e 6-solo cultivado com eucalipto e braquiária com uso de 60 Mg ha-1 de lodo de esgoto. Nas camadas do solo de 0,00-0,05; 0,05-0,10; 0,10-0,20; e 0,20-0,30 m, foram estudadas as propriedades físicas do solo: macroporosidade, microporosidade; porosidade; e densidade do solo. Na braquiária foram avaliadas as matérias verde e seca e, no eucalipto, a altura média de planta e o DAP (diâmetro à altura do peito). Concluiu-se que o solo estudado está sendo recuperado por meio dos tratamentos estabelecidos. Dentre eles, destacam-se os tratamentos com a utilização do lodo, que influenciaram as propriedades físicas do solo, proporcionaram mais rendimentos de matérias verde e seca da braquiária e promoveram maior crescimento das plantas de eucalipto. O crescimento vegetal, a densidade do solo, a porosidade total e a macroporosidade foram os melhores indicadores da recuperação do solo.

Rotação de culturas e propriedades físicas e químicas em Latossolo Vermelho de Cerrado sob preparo convencional e semeadura direta em adoção

O manejo inadequado do solo tem promovido a degradação de suas propriedades físicas, químicas e biológicas. O objetivo deste trabalho foi avaliar, após três anos da instalação de sistemas de manejo do solo, os efeitos da rotação com adubo verde, soja ou milho (verão) e feijão de inverno, sendo utilizadas as seguintes espécies na adubação verde: mucuna-preta, milheto, crotalária e guandu, nas propriedades físicas e químicas de um Latossolo Vermelho distroférrico e na produtividade das culturas. Outro tratamento foi adicionado como alternativa à adubação verde, o pousio. Os sistemas de manejo do solo foram: semeadura direta não consolidada e preparo convencional. O estudo foi realizado em Selvíria-MS, no ano agrícola de 1999/2000. O delineamento experimental foi em blocos casualizados com parcelas subdivididas e quatro repetições. O sistema de semeadura direta, após três anos de instalada a rotação, degradou mais as propriedades físicas do solo na camada superficial. Por outro lado, neste sistema e camada de solo, houve acréscimo no teor de matéria orgânica e no pH, bem como na produtividade do milho, superior à do sistema de preparo convencional. O feijão em rotação à cultura do milho, na semeadura convencional, e em rotação à soja, na semeadura direta, foi a melhor opção quanto à produtividade.

Síntese e caracterização de ferritas de níquel dopadas com cobalto e efeito da substituição nas suas propriedades magnéticas

The ferrite composition Ni1 - xCoxFe2O4 (0 ≤ x ≤ 0.75) were obtained by the method of microwave assisted synthesis and had their structural and magnetic properties evaluated due to the effect of the substitution of Ni by Co. The compounds were prepared: according to the concept of chemical propellants and heated in the microwave oven with power 7000kw. The synthesized material was characterized by absorption spectroscopy in the infrared (FTIR), Xray diffraction (XRD) using the Rietveld refinement, specific surface area (BET) , scanning electron microscopy (SEM) with aid of energy dispersive analysis (EDS) and magnetic measurements (MAV). The results obtained from these techniques confirmed the feasibility of the method of synthesis employed to obtain the desired spinel structure, the ferrite, nickel ferrite as for nickel doped with cobalt. The results from XRD refinement ally showed the formation of secondary phases concerning stages α - Fe2O3, FeO, (FeCo)O e Ni0. On the other hand, there is an increase in crystallite size with the increase of cobalt in systems, resulting in an increased crystallinity. The results showed that the BET systems showed a reduction in specific surface area with the increase of cobalt and from the SEM, the formation of irregular porous blocks and that the concentration of cobalt decreased the agglomerative state of the system. The magnetic ferrites studied showed different characteristics according to the amount of dopant used, ranging from a very soft magnetic material (easy magnetization and demagnetization ) - for the system without cobalt - a magnetic material with a little stiffer behavior - for systems containing cobalt. The values of the coercive field increased with the increasing growth of cobalt, and the values of saturation magnetization and remanence increased up to x = 0,25 and then reduced. The different magnetic characteristics presented by the systems according to the amount of dopant used, allows the use of these materials as intermediates magnetic

Densidade do solo e infiltração de água como indicadores da qualidade física de um Latossolo Vermelho distrófico em recuperação

A necessidade cada vez maior de alimentos, espaço e condições para sobrevivência faz com que as interferências antrópicas no ambiente sejam cada vez maiores. Solos intensivamente cultivados e de forma inadequada são degradados, assim como a construção de obras civis no meio rural sem atender à legislação pertinente tudo isso tem ocasionado problemas ao meio. Várias técnicas têm sido utilizadas para recuperar esses solos, sendo a principal delas a adição de MO. Contudo, informações sobre tempo para recuperação do solo, influência dos tipos de material orgânico e indicadores das alterações ainda são escassas. Este trabalho objetivou avaliar a recuperação das propriedades de um Latossolo Vermelho distrófico, de onde foi retirado material usado na terraplanagem e nas fundações da usina hidrelétrica de Ilha Solteira-SP, utilizando-se como indicadores de qualidade física a densidade do solo e a taxa de infiltração de água. A pesquisa foi feita em uma área onde se retirou uma camada de solo de 8,60 m. O delineamento experimental foi em blocos casualizados, com cinco repetições e cinco tratamentos: testemunha (solo exposto sem técnicas de recuperação); espécie arbórea gonçalo-alves (Astronium fraxinifolium Schott); gonçalo-alves + feijão-de-porco (Canavalia ensiformis); gonçalo-alves + nabo forrageiro (Raphanus sativus); e gonçalo-alves + gramínea (Brachiaria decumbens) + lodo de esgoto (60 Mg ha-1). A densidade do solo foi avaliada antes e 356 dias após a implantação dos tratamentos, e a infiltração de água no solo foi determinada 188 dias depois da instalação dos tratamentos. Concluiu-se que ocorrem melhorias na qualidade do solo quando efetuado o seu preparo e a adição de lodo de esgoto e adubos verdes. A densidade do solo e a infiltração de água do solo são bons indicadores na avaliação dessas melhorias. As diferentes fontes de MO adicionadas ao solo e a ação do preparo deste interagem de maneira semelhante na recuperação da sua qualidade, porém a combinação lodo de esgoto mais braquiária proporciona maior altura de planta da espécie gonçalo-alves.

Propriedades químicas de um latossolo vermelho distrófico de cerrado sob diferentes usos e manejos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Síntese, caracterização de ferritas espinélio com propriedades magnéticas e absorvedoras de microondas

Were synthesized spinel-type ferrites with general formula Ni0,8Mg0.2-xMxFe2O4, where M represents the doping Mn, Co or Mn + Co simultaneously, x ranges for the values 0.02, 0.05 and 0.1. The value of x was divided by 2 in cases where M equals Mn and Co conjugates. We used the citrate precursor method and heat treatment to obtain the phases at 1100°C. The materials were characterized by XRD, TGA/ DTGA, SEM, MAV and reflectivity measurements by the method of waveguide. Powders to 350°C/3.5 h were crystalline and nanosized. According to the results this temperature all powders have a percentage of ferrite phase over 90%. The composition had the addition of Mn and Co simultaneously showed a higher percentage of secondary phase NiO, 5.8%. The TGA/DTGA curves indicate that this sample reached phase (s) crystalline (s) at lowest temperatures. The X-ray diffractograms of the samples calcined at 350°C and 1100°C were treated with the Rietveld refinament technique. The powders calcined at 1100 °C/3h in air show to be 100% except spinel phase composition with 0.02 doping. The micrographs show clusters of particles with sizes smaller than 1 μm in calcination temperature of 1100°C which agreed with the result of Rietveld refinement. In the compositions doped with Mn were higher values of magnetization (45.90 and 53.20 Am2/kg), which did not cause high microwave absorption. The theoretical calculation of magnetization (MT) was consistent with the results, considering that there was agreement between the increase of magnetization experimental and theoretical. It was observed that there was the interrelation of the final effect of absorption with the thickness of MARE, the composition of ferrimagnetic materials and in particular the specific values of frequency. The analysis shows that the reflectivity increases in the concentration of cobalt increased the frequency range and also for absorption 10.17 GHz and 84%, respectively. The best result of chemical homogeneity and the value of 2.96 x 10-2 tesla coercive field were crucial for high performance ferrite absorber with 0.1 cobalt. The Cobalt has high magnetocrystalline anisotropy, it is associated with an increased coercive field, Hc. Therefore, this property improves the results of reflectivity of spinel ferrites

Entendendo as propriedades do arenito Botucatu e sua utilização como meio poroso para estudos envolvendo o deslocamento de fluidos poliméricos

The development of products whose purpose is to promote blockages in high permeability zones as well as to control the hydrate or scale formation also needs some tests in porous media before using the product in the field, where attempts and unavoidable operational errors costs would able to derail any projects. The aim of this study was to analyze and compare the Botucatu and Berea sandstones properties, involving problems related to loss permeability. It was observed that even cores of Berea, without expansible clays in their composition had their permeability reduced, as soon as the salinity of brine reached a lower limit. As expected, the same happened with the Botucatu sandstone samples, however, in this case, the sensitivity to low salinity was more pronounced. In a second phase, the research was focused on the Botucatu Sandstone behavior front of dilute polymer solutions injection, checking the main relationships between the Rock / Fluid interactions, considering the Mobility Reduction, Resistance and Residual Resistance Factors, as well as adsorption/desorption processes of these polymers, and the polymer molecules average size and porous sandstone average size ratio. The results for both phases showed a real feasibility of using the Botucatu sandstone in laboratory tests whose objective is the displacement of fluids through porous media

Interações entre a carboximetilcelulose, carbonato de cálcio e bentonita: repercussões sobre as propriedades dos fluidos de perfuração aquosos

The role of carboxymethylcellulose (CMC) in association to calcium carbonate particles (CaCO3) in most water-based drilling fluids is to reduce the fluid loss to the surrounding formation. Another essential function is to provide rheological properties capable of maintaining in suspension the cuttings during drilling operation. Therefore, it is absolutely essential to correlate the polymer chemical structure (degree of substitution, molecular weight and distribution of substituent) with the physical-chemical properties of CaCO3, in order to obtain the better result at lower cost. Another important aspect refers to the clay hydration inhibitive properties of carboxymethylcellulose (CMC) in drilling fluids systems. The clay swelling promotes an undesirable damage that reduces the formation permeability and causes serious problems during the drilling operation. In this context, this thesis consists of two main parts. The first part refers to understanding of interactions CMC-CaCO3, as well as the corresponding effects on the fluid properties. The second part is related to understanding of mechanisms by which CMC adsorption occurs onto the clay surface, where, certainly, polymer chemical structure, ionic strength, molecular weight and its solvency in the medium are responsible to affect intrinsically the clay layers stabilization. Three samples of carboximetilcellulose with different molecular weight and degree of substitution (CMC A (9 x 104 gmol DS 0.7), CMC B (2.5 x 105 gmol DS 0.7) e CMC C (2.5 x 105 gmol DS 1.2)) and three samples of calcite with different average particle diameter and particle size distribution were used. The increase of CMC degree of substitution contributed to increase of polymer charge density and therefore, reduced its stability in brine, promoting the aggregation with the increase of filtrate volume. On the other hand, the increase of molecular weight promoted an increase of rheological properties with reduction of filtrate volume. Both effects are directly associated to hydrodynamic volume of polymer molecule in the medium. The granulometry of CaCO3 particles influenced not only the rheological properties, due to adsorption of polymers, but also the filtration properties. It was observed that the lower filtrate volume was obtained by using a CaCO3 sample of a low average size particle with wide dispersion in size. With regards to inhibition of clay swelling, the CMC performance was compared to other products often used (sodium chloride (NaCl), potassium chloride (KCl) and quaternary amine-based commercial inhibitor). The low molecular weight CMC (9 x 104 g/mol) showed slightly lower swelling degree compared to the high molecular weight (2.5 x 105 g/mol) along to 180 minutes. In parallel, it can be visualized by Scanning Electron Microscopy (SEM) that the high molecular weight CMC (2.5 x 105 g/mol e DS 0.7) promoted a reduction in pores formation and size of clay compared to low molecular weight CMC (9.0 x 104 g/mol e DS 0.7), after 1000 minutes in aqueous medium. This behavior was attributed to dynamic of interactions between clay and the hydrodynamic volume of CMC along the time, which is result of strong contribution of electrostatic interactions and hydrogen bounds between carboxylate groups and hydroxyls located along the polymer backbone and ionic and polar groups of clay surface. CMC adsorbs on clay surface promoting the skin formation , which is responsible to minimize the migration of water to porous medium. With the increase of degree of substitution, it was observed an increase of pores onto clay, suggesting that the higher charge density on polymer is responsible to decrease its flexibility and adsorption onto clay surface. The joint evaluation of these results indicate that high molecular weight is responsible to better results on control of rheological, filtration and clay swelling properties, however, the contrary effect is observed with the increase of degree of substitution. On its turn, the calcite presents better results of rheological and filtration properties with the decrease of average viii particle diameter and increase of particle size distribution. According to all properties evaluated, it has been obvious the interaction of CMC with the minerals (CaCO3 and clay) in the aqueous medium

Estudo do comportamento mecânico de estruturas de solo-cimento reforçado com fibras de coco e hastes de bambu

In this work the use of coconut fiber (coir) and bamboo shafts as reinforcement of soil-cement was studied, in order to obtain an alternative material to make stakes for fences in rural properties. The main objective was to study the effect of the addition of reinforcement to the soil-cement matrix. The effect of humidity on the mechanical properties was also analyzed. The soil-cement mortar was composed by a mixture, in equal parts, of soil and river sand, 14% in weight of cement and 10 % in weight of water. As reinforcement, different combinations of (a) coconut fiber with 15 mm mean length (0,3 %, 0,6 % and 1,2 % in weight) and (b) bamboo shafts, also in crescent quantities (2, 4 and 8 shafts per specimen) were used. For each combination 6 specimens were made and these were submitted to three point flexural test after 28 days of cure. In order to evaluate the effect of humidity, 1 specimen from each of the coconut fiber reinforced combination was immersed in water 24 hours prior to flexural test. The results of the tests carried out indicated that the addition of the reinforcement affected negatively the mechanical resistance and, on the other hand, increased the tenacity and the ductility of the material.

Propriedades físicas de planetas extrasolares

ROTATION is one the most important aspects to be observed in stellar astrophysics. Here we investigate that particularly in stars with planets. This physical parameter supplies information about the distribution of angular momentum in the planetary system, as well as its role on the control of dierent phenomena, including coronal and cromospherical emission and on the ones due of tidal effects. In spite of the continuous solid advances made on the study of the characteristics and properties of planet host stars, the main features of their rotational behavior is are not well established yet. In this context, the present work brings an unprecedented study about the rotation and angular momentum of planet-harbouring stars, as well as the correlation between rotation and stellar and planetary physical properties. Our analysis is based on a sample of 232 extrasolar planets, orbiting 196 stars of dierent luminosity classes and spectral types. In addition to the study of their rotational behavior, the behavior of the physical properties of stars and their orbiting planets was also analyzed, including stellar mass and metallicity, as well as the planetary orbital parameters. As main results we can underline that the rotation of stars with planets present two clear features: stars with Tef lower than about 6000 K have slower rotations, while among stars with Tef > 6000 K we and moderate and fast rotations, though there are a few exceptions. We also show that stars with planets follow mostly the Krafts law, namely < J > / v rot. In this same idea we show that the rotation versus age relation of stars with planets follows, at least qualitatively, the Skumanich and Pace & Pasquini laws. The relation rotation versus orbital period also points for a very interesting result, with planet-harbouring stars with shorter orbital periods present rather enhanced rotation

Características físico-químicas de amidos modificados de grau alimentício comercializados no Brasil

Amidos nativos e modificados têm grande importância na indústria de alimentos, sendo empregados principalmente como espessantes e/ou estabilizantes. As limitações das pastas e géis obtidos a partir de amidos nativos tornaram necessário o desenvolvimento de muitos tipos de amidos modificados para aplicações alimentícias. Neste trabalho, algumas amostras de amidos modificados (n=20) disponíveis no Brasil foram recebidas de empresas produtoras e analisadas em relação a algumas características físico-químicas e propriedades tecnológicas. Um levantamento do uso de amidos modificados em alimentos também é apresentado, revelando crescente interesse pela indústria nesses ingredientes. Constatou-se que, enquanto alguns alimentos industrializados, como maioneses contêm em suas formulações amidos modificados, outros como condimento preparado de mostarda contêm apenas amido nativo. As análises físico-químicas permitiram concluir que alguns amidos modificados apresentavam teores elevados de acidez, relacionados à presença de reagentes utilizados em sua obtenção, não havendo presença de carboxilas nas suas macromoléculas. de maneira geral, os resultados de algumas propriedades tecnológicas avaliadas, tais como viscosidade aparente das pastas, resistência a congelamento/descongelamento e propriedade de expansão, estavam de acordo com a descrição dos produtos. As fontes mais observadas nas modificações foram, em ordem decrescente de importância, a mandioca, o milho ceroso e o milho regular.

Caracterização físico-química da mucilagem de inhame liofilizada

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)