Pirólise termoquímica de pós da fibra de coco seco em um reator de cilindro rotativo para produção de bio-óleo

This master thesis aims at developing a new methodology for thermochemical degradation of dry coconut fiber (dp = 0.25mm) using laboratory rotating cylinder reactor with the goal of producing bio-oil. The biomass was characterized by infrared spectroscopy with Fourier transform FTIR, thermogravimetric analysis TG, with evaluation of activation energy the in non-isothermal regime with heating rates of 5 and 10 °C/min, differential themogravimetric analysis DTG, sweeping electron microscopy SEM, higher heating value - HHV, immediate analysis such as evaluated all the amounts of its main constituents, i.e., lignin, cellulose and hemicelluloses. In the process, it was evaluated: reaction temperature (450, 500 and 550oC), carrier gas flow rate (50 and 100 cm³/min) and spin speed (20 and 25 Hz) to condensate the bio-oil. The feed rate of biomass (540 g/h), the rotation of the rotating cylinder (33.7 rpm) and reaction time (30 33 min) were constant. The phases obtained from the process of pyrolysis of dry coconut fiber were bio-oil, char and the gas phase non-condensed. A macroscopic mass balance was applied based on the weight of each phase to evaluate their yield. The highest yield of 20% was obtained from the following conditions: temperature of 500oC, inert gas flow of 100 cm³/min and spin speed of 20 Hz. In that condition, the yield in char was 24.3%, non-condensable gas phase was 37.6% and losses of approximately 22.6%. The following physicochemical properties: density, viscosity, pH, higher heating value, char content, FTIR and CHN analysis were evaluated. The sample obtained in the best operational condition was subjected to a qualitative chromatographic analysis aiming to know the constituents of the produced bio-oil, which were: phenol followed by sirigol, acetovanilona and vinyl guaiacol. The solid phase (char) was characterized through an immediate analysis (evaluation of moisture, volatiles, ashes and fixed carbon), higher heating value and FTIR. The non-condensing gas phase presented as main constituents CO2, CO and H2. The results were compared to the ones mentioned by the literature.

Dissipation of triadimefon on the solid/gas interface

The dissipation or triadimefon, as pure solid and in the Bayleton 5 commercial formulation, was studied under controlled and natural conditions. Volatilization and photodegradation were shown to be the main dissipation processes. The volatilization results can be described by an empirical model assuming exponential decay of the volatilization rate. The filler of the commercial formulation is determinant for the volatilization but has little effect on the photodegradation rates. The main photoproducts were identified and a reaction mechanism proposed. (C) 2001 Elsevier Science Ltd. All rights reserved.

Photophysics and photochemistry of azole fungicides: triadimefon and triadimenol

Photophysics and photochemistry of pesticides triadimefon {1-(4-chlorophenoxy)-3,3-dimethyl-1-(1H-1,2,4-triazol-1-yl) butanone} and triadimenol {1-(4-chlorophenoxy)-3,3-dimethyl-1-(1H-1,2,4-triazol-1-yl) butan-2-ol} were studied in the solution. The excited singlet states were identified by comparison with the absorption spectra of adequate model compounds, in several solvents. The first excited singlet state of triadimefon is an n, pi* state localized on the carbonyl group, while higher excited states are localized on the chlorophenoxy group and have a pi, pi* character. The lowest singlet state of triadimenol is pi, pi* state, since a methoxyl group replaces the carbonyl group of triadimefon. Triadimefon shows a weak fluorescence from the n, pi* state, upon excitation at both 310 and 250 nm. This suggests a fast intramolecular energy transfer process from the localized pi, pi* state of the chlorophenoxy group to the n, pi* state of the carbonyl group. The photodegradation quantum yield of triadimefon in cyclohexane at 313 run is 0.022. Triadimenol is photostable, under the same conditions. Two major photodegradation products of triadimefon and triadimenol were identified: 4-chlorophenol and 1,2,4-triazole. 4-Chlorophenoxyl radicals were detected by flash photolysis, suggesting a homolytic cleavage of the C-O bond of the asymmetric carbon. (C) 2001 Elsevier Science B.V. All rights reserved.

Surface photochemistry of pesticides: an approach using diffuse reflectance and chromatography techniques

The photochemistry of pesticides triadimenol and triadimefon was studied on cellulose and beta-cyclodextrin (beta-CD) in controlled and natural conditions, using diffuse reflectance techniques and chromatographic analysis. The photochemistry of triadimenol occurs from the chlorophenoxyl moiety, while the photodegradation of triadimefon also involves the carbonyl group. The formation of 4-chlorophenoxyl radical is one of the major reaction pathways for both pesticides and leads to 4-chlorophenol. Triadimenol also undergoes photooxidation and dechlorination, leading to triadimefon and dechlorinated triadimenol, respectively. The other main reaction process of triadimefon involves alpha-cleavage from the carbonyl group, leading to decarbonylated compounds. Triadimenol undergoes photodegradation at 254 nm but was found to be stable at 313 nm, while triadimefon degradates in both conditions. Both pesticides undergo photochemical decomposition under solar radiation, being the initial degradation of rate per unit area of triadimefon 1 order of magnitude higher than the observed for triadimenol in both supports. The degradation rates of the pesticides were somewhat lower in beta-CD than on cellulose. Photoproduct distribution of triadimenol and triadimefon is similar for the different irradiation conditions, indicating an intramolecular energy transfer from the chlorophenoxyl moiety to the carbonyl group in the latter pesticide.

Photochemistry of 4-chlorophenol on cellulose and silica

The photochemistry of 4-chlorophenol (4-CP) was studied on silica and cellulose, using time-resolved diffuse reflectance techniques and product degradation analysis. The results have shown that the photochemistry of 4-CP depends on the support, on the concentration, and also on the sample preparation method. Transient absorption and photoproduct results can be understood by assuming the formation of the carbene 4-oxocyclohexa-2,5-dienylidene in both supports. On cellulose, at concentrations lower than 10 mumol g(-1), the carbene leads to the unsubstituted phenoxyl radical, and phenol is the main degradation product. At higher concentrations a new transient resulting from phenoxyl radicals coupling was also observed, and dihydroxybiphenyls are also formed. The reaction of the carbene with ground-state 4-CP was also detected through the formation of 5-chloro-2,4'-dihydroxybiphenyl. 4-Chlorophenoxyl radical and degradations products resulting from its coupling were also detected. Oxygen has little effect on the photochemistry of 4-CP on cellulose. On silica the transient benzoquinone O-oxide was formed in the presence of oxygen. Benzoquinone and hydroquinone are the main degradation products. In well-dried samples the formation of hydroquinone is reduced. At higher concentrations the same products as detected on cellulose were observed. 4-CP undergoes slow photochemical decomposition under solar radiation in both supports. The same main degradation products were observed in these conditions.

Aqueous photochemistry of pesticides triadimefon and triadimenol

The photochemistry of pesticides triadimefon and triadimenol was studied in aqueous solution and in methanol/water mixtures, in controlled and natural conditions. The photodegradation kinetics and product distribution are strongly dependent on the solvent and on the irradiation wavelength. The degradation rates are faster at 254 nm than at 313 nm. The kinetics is faster in water than methanol. Direct photoreaction is an important dissipation pathway of triadimefon in natural water systems while triadimenol is stable in these conditions. 1,2,4-Triazole and 4-chlorophenol are two of the major photodegradation products. The formation of the 4-chlorophenoxyl radical was detected for both pesticides in methanol and methanol/water mixtures. In methanol/water mixtures the reaction of both pesticides also occurs with 4-chlorophenolate formation, which increases with the water content. The photochemical studies of pesticides and other pollutants should be made in conditions as similar as possible to those observed in environmental systems. (C) 2003 Elsevier Science B.V. All rights reserved.

Novel laser-induced luminescence resulting from benzophenone/O-propylated p-tert-butylcalix[4]arene complexes. A diffuse reflectance study

Laser-induced room temperature luminescence of air-equilibrated benzophenone/O-propylated p-tert-butylcalix[ 4] arene solid powdered samples revealed the existence of a novel emission, in contrast with benzophenone/p-tertbutylcalix[ 4] arene complexes, where only benzophenone emits. This novel emission was identified as phosphorescence of 1-phenyl-1,2-propanedione, which is formed as the result of an hydrogen atom abstraction reaction of the triplet excited benzophenone from the propoxy substituents of the calixarene. Room temperature phosphorescence was obtained in air-equilibrated samples in all propylated hosts. The decay times of the benzophenone emission vary greatly with the degree of propylation, the shortest lifetimes being obtained in the tri- and tetrapropylated calixarenes. Triplet - triplet absorption of benzophenone was detected in all cases, and is the predominant absorption in the p-tert-butylcalix[ 4] arene case, where an endo-calix complex is formed. Benzophenone ketyl radical formation occurs with the O-propylated p-tert-butylcalix[ 4] arenes hosts, suggesting a different type of host/guest molecular arrangement. Diffuse reflectance laser. ash photolysis and gas chromatography - mass spectrometry techniques provided complementary information, the former about transient species and the latter regarding the final products formed after light absorption. Product analysis and identification clearly show that the two main degradation photoproducts following laser excitation in the propylated substrates are 1-phenyl-1,2- propanedione and 2- hydroxybenzophenone, although several other minor photodegradation products were identified. A detailed mechanistic analysis is proposed. While the solution photochemistry of benzophenone is dominated by the hydrogen abstraction reaction from suitable hydrogen donors, in these solid powdered samples, the alpha-cleavage reaction also plays an important role. This finding occurs even with one single laser pulse which lasts only a few nanoseconds, and is apparently related to the fact that scattered radiation exists, due to multiple internal reflections possibly trapping light within non-absorbing microcrystals in the sample, and is detected until at least 20 mus after the laser pulse. This could explain how photoproducts thus formed could also be excited with only one laser pulse.

Photo Degradation of Cotnaminants of Emerging concern (CECs) under Simulated Solar Radiation: Implications for their Environmental Fate

Contaminants of emerging concern (CECs) are continuously being released into the environment mainly because of their incomplete removal in the sewage treatment plants (STPs). The CECs selected for the study include antibiotics (macrolides, sulfonamides and ciprofloxacin), sucralose (an artificial sweetener) and dioctyl sulfosuccinate (DOSS, chemical dispersant used in the Deepwater Horizon oil spill). After being discharged into waterways from STPs, photo degradation is a key factor in dictating the environmental fate of antibiotics and sucralose. Photodegradation efficiency depends on many factors such as pH of the matrix, matrix composition, light source and structure of the molecule. These factors exert either synergistic or antagonistic effects in the environment and thus experiments with isolated factors may not yield the same results as the natural environmental processes. Hence in the current study photodegradation of 13 CECs (antibiotics, sucralose and dicotyl sulfosuccinate) were evaluated using natural water matrices with varying composition (deionized water, fresh water and salt water) as well as radiation of different wavelengths (254 nm, 350 nm and simulated solar radiation) in order to mimic natural processes. As expected the contribution of each factor on the overall rate of photodegradation is contaminant specific, for example under similar conditions, the rate in natural waters compared to pure water was enhanced for antibiotics (2-11 fold), significantly reduced for sucralose (no degradation seen in natural waters) and similar in both media for DOSS. In general, it was observed that the studied compounds degraded faster at 254 nm, while when using a simulated sunlight radiation the rate of photolysis of DOSS increased and the rates for antibiotics decreased in comparison to the 350 nm radiation. The photo stability of the studied CECs followed the order sucralose > DOSS > macrolides > sulfonamides > ciprofloxacin and a positive relationship was observed between photo stability and their ubiquitous presence in natural aquatic matrices. An online LC-MS/MS method was developed and validated for sucralose and further applied to reclaimed waters (n =56) and drinking waters (n = 43) from South Florida. Sucralose was detected in reclaimed waters with concentrations reaching up to 18 µg/L. High frequency of detection (> 80%) in drinking waters indicate contamination of ground waters in South Florida by anthropogenic activity.

The effect of sample and sample matrix on DNA processing: Mechanisms for the detection and management of inhibition in forensic samples

The presence of inhibitory substances in biological forensic samples has, and continues to affect the quality of the data generated following DNA typing processes. Although the chemistries used during the procedures have been enhanced to mitigate the effects of these deleterious compounds, some challenges remain. Inhibitors can be components of the samples, the substrate where samples were deposited or chemical(s) associated to the DNA purification step. Therefore, a thorough understanding of the extraction processes and their ability to handle the various types of inhibitory substances can help define the best analytical processing for any given sample. A series of experiments were conducted to establish the inhibition tolerance of quantification and amplification kits using common inhibitory substances in order to determine if current laboratory practices are optimal for identifying potential problems associated with inhibition. DART mass spectrometry was used to determine the amount of inhibitor carryover after sample purification, its correlation to the initial inhibitor input in the sample and the overall effect in the results. Finally, a novel alternative at gathering investigative leads from samples that would otherwise be ineffective for DNA typing due to the large amounts of inhibitory substances and/or environmental degradation was tested. This included generating data associated with microbial peak signatures to identify locations of clandestine human graves. Results demonstrate that the current methods for assessing inhibition are not necessarily accurate, as samples that appear inhibited in the quantification process can yield full DNA profiles, while those that do not indicate inhibition may suffer from lowered amplification efficiency or PCR artifacts. The extraction methods tested were able to remove >90% of the inhibitors from all samples with the exception of phenol, which was present in variable amounts whenever the organic extraction approach was utilized. Although the results attained suggested that most inhibitors produce minimal effect on downstream applications, analysts should practice caution when selecting the best extraction method for particular samples, as casework DNA samples are often present in small quantities and can contain an overwhelming amount of inhibitory substances.^

Effects in ultrafast laser micromachining PMMA-based optical fibre grating

Ultrafast laser owns extreme small beam size and high pulse intensity which enable spatial localised modification either on the surface or in the bulk of materials. Therefore, ultrafast laser has been widely used to micromachine optical fibres to alter optical structures. In order to do the precise control of the micromachining process to achieve the desired structure and modification, investigations on laser parameters control should be carried out to make better understanding of the effects in the laser micromachining process. These responses are important to laser machining, most of which are usually unknown during the process. In this work, we report the real time monitored results of the reflection of PMMA based optical fibre Bragg gratings (POFBGs) during excimer ultraviolet laser micromachining process. Photochemical and thermal effects have been observed during the process. The UV radiation was absorbed by the PMMA material, which consequently induced the modifications in both spatial structure and material properties of the POFBG. The POFBG showed a significant wavelength blue shift during laser micromachining. Part of it attributed to UV absorption converted thermal energy whilst the other did not disappear after POFBG cooling off, which attributed to UV induced photodegradation in POF.

Enzymatic activity on sediments and nematode assemblage responses during seagrass beds habitat recovery following the disturbance of the traditional digging activity of bivalves harvesting.

Sediment digging is an anthropogenic activity connected to the exploitation of living resources in estuarine and marine environments. The knowledge on the functional responses of the benthic assemblages to the physical disturbance is an important baseline to understand the ecological processes of the habitat recovery and restoration and to develop tools for the management of the harvesting activities. To investigate the effects of the digging activity of the bivalves on Zostera noltii seagrass beds a manipulative field experiment was conducted that included the enzymatic activity of sediments and the associated nematode assemblages. Four plots (two undisturbed serving as control and two dug to collect bivalves - treatment) with 18 subplots were randomly located at seagrass beds in the Mira estuary at the SW coast of Portugal. Samples were randomly and unrepeatably collected from three subplots of each plot in five different occasions, before sediment digging (T0) up to six months after disturbance (T5). Microbial activity in sediments was assess by determining the extracelular enzymatic activity of six hydrolytic enzymes (sulfatase, phosphatase, b -N-acetilglucosaminidase, b-glucosidase, urease, protease) and two oxidoreductases (phenol oxidase and peroxidase). The microbial community status was also assessed through the measurement of dehydrogenase, which reflects microbial respiration. The nematode assemblages composition, biodiversity and trophic composition at different sampling occasions were also analyzed. The fluorometric and biochemical parameters analysed of the Z. noltii plants during the experimental period showed a recovery of the seagrass beds, and it was detected an increase of the enzymatic activity of the sediments after disturbance. The nematodes assemblages were similar in all sampling occasions. The seagrass beds and the nematodes assemblages associated showed a high resilience to the stress caused by the traditional bivalves digging activity. The obtained results allow the development of a management programme for the commercial fishing activity to maintain the good environmental status and minimized the secondary environmental effects on marine and estuarine habitats through the establishment of a baseline for the regulation of the harvesting frequency.

Chemical and aromatic characteristics of Brazilian tropical wines.

Traditional winegrowing areas are located in temperate climate zones and allow to produce grapes only once per year. Tropical wines have been elaborated in India, Thailand, Venezuela and Brazil and present another kind of viticulture, as compared with countries located in temperate climate zones. Northeast of Brazil started wine production twenty six years ago. This region vines can produce two or three crops per year, depending of the cycle of different cultivars. Harvests can be scaled throughout the year, mainly between May and December, corresponding to the dry season. Red, white, rosé and sparkling wines are being elaborated in the region. The objective of this work was to determine the physico-chemical and aromatic characteristics of some tropical wines elaborated in Northeast of Brazil, with grapes harvested in November 2008. Wines were elaborated using traditional method with control of the alcoholic and malolactic fermentation temperatures, at 25 and 18ºC for red wines, respectively, and at 18ºC for alcoholic fermentation of the white wines. After stabilization and bottling and wines were analyzed to determine physico-chemical characteristics, like alcohol degree, pH, total and volatile acidities, dry extract, sulfur dioxide, total anthocyanin and total phenol index. Aromatic profile was determined by gas chromatography, while 19 esters and 6 superior alcohols were identified. Wines presented different chemical and aromatic characteristics according to different grape cultivars.

Theoretical and experimental study on the role of benzoquinone in the Guerbet reaction catalyzed by a ruthenium complex

The benzoquinone was found as an effective co-catalyst in the ruthenium/NaOEt-catalyzed Guerbet reaction. The co-catalyst behavior has therefore been investigated through experimental and computational methods. The reaction products distribution shows that the reaction speed is improved by the benzoquinone supplement since the beginning of the process, having a minimal effect on the selectivity toward alcoholic species. DFT calculations were performed to investigate two hypotheses for the kinetic effects: i) a hydrogen storage mechanism or ii) a basic co-catalysis of 4-hydroxiphenolate. The most promising results were found for the latter hypothesis, where a new mixed mechanism for the aldol condensation step of the Guerbet process involves the hydroquinone (i.e. the reduced form of benzoquinone) as proton source instead of ethanol. This mechanism was found to be energetically more favorable than an aldol condensation in absence of additive, suggesting that the hydroquinone derived from benzoquinone could be the key species affecting the kinetics of the overall process. To verify this theoretical hypothesis, new phenol derivatives were tested as additives in the Guerbet reaction. The outcomes confirmed that an aromatic acid (stronger than ethanol) could improve the reaction kinetics. Lastly, theoretical products distributions were simulated and compared to the experimental one, using the DFT computations to build the kinetic models.