Evaluation of the kinetics of xylose formation from dilute sulfuric acid hydrolysis of forest residues of Eucalyptus grandis

Dilute acid hydrolysis studies were performed on forest residues of Eucalyptus grandis, in a cylindrical reactor of stainless steel. The kinetics of this hydrolysis reaction was investigated employing 0.65% sulfuric acid, a residue/acid solution ratio of 1/9 (w/w), temperatures of 130, 140, 150, and 160 degrees C, and reaction times in the range 20-100 min. The results showed that, under the optimized conditions of acid hydrolysis employed in this study, the variables temperature and reaction time had a strong influence on hemicellulose removal and a small influence on the degree of lignin and cellulose removal. The highest xylose extraction yield was 87.6% attained at 160 degrees C, after 70 min reaction time, simultaneously with the formation of decomposition products, namely 2.8% acetic acid, 0.6% furfural, and 0.06% 5-hydroxymethylfurfural. A similar xylose extraction yield (82.8%) was observed at 150 degrees C after 100 min, with the formation of 3.2% acetic acid, 1.0% furfural, and 0.07% 5-hydroxymethylfurfural. The kinetic parameters determined at 130, 140, 150, and 160 degrees C for degradation of xylan present in the hemicellulose of the eucalyptus forest residue during the formation of xylose were the first-order reaction rate constants (k) for each temperature, 1.22 x 10(-4), 2.12 x 10(-4), 5.43 x 10(-4), and 9.05 x 10(-4) s(-1), respectively, and an activation energy (E-a) of 101.3 kJ mol(-1).

Optimisation of environmental gas cleaning routes for solid wastes cogeneration systems. Part II - Analysis of waste incineration combined gas/steam cycle

In the first paper of this paper (Part I), conditions were presented for the gas cleaning technological route for environomic optimisation of a cogeneration system based in a thermal cycle with municipal solid waste incineration. In this second part, an environomic analysis is presented of a cogeneration system comprising a combined cycle composed of a gas cycle burning natural gas with a heat recovery steam generator with no supplementary burning and a steam cycle burning municipal solid wastes (MSW) to which will be added a pure back pressure steam turbine (another one) of pure condensation. This analysis aims to select, concerning some scenarios, the best atmospheric pollutant emission control routes (rc) according to the investment cost minimisation, operation and social damage criteria. In this study, a comparison is also performed with the results obtained in the Case Study presented in Part I. (c) 2007 Elsevier Ltd. All rights reserved.

Mechanical properties of HIPS/sugarcane bagasse fiber composites after accelerated weathering

The effect of accelerated weathering on the visual appearance and on mechanical properties of high impact polystyrene (HIPS) as well as HIPS reinforced with mercerized and bleached sugarcane bagasse fibers composites are investigated. After accelerated weathering period of 900 h, under UV-B radiation and moisture regular cycles, changes in mechanical properties are investigated by tensile tests. Materials fracture surfaces are investigated by scanning electron microscopy (SEM). The study showed that the exposure time was sufficient to change the visual appearance of HIPS as the composites. From this study, it was observed that composites reinforced with bleached fibers are less susceptible to accelerated weathering exposure than composites reinforced with mercerized fibers, which is explained by the higher amount of lignin present in mercerized fibers. (C) 2010 Published by Elsevier Ltd. Selection and peer-review under responsibility of [name organizer]

UV exposure of polymeric geomembranes

The break of polymer chemical bonds may occur due to penetration of sun short wavelengths. In sanitary landfills for instance, ultraviolet radiation affects uncovered materials and can be dangerous during the installation of the liner and before the placement of the waste. Only the ultraviolet part of the light is harmful to the geosynthetic materials, moreover, each material is sensitive to a particular wavelength. This article evaluates the effects of UV degradation and condensation in black HDPE (1.0 and 1.5 mm) and white HDPE (textured - 1.0 mm) geomembrane that were tested in laboratory during 6 months. The tests were performed using a weatherometer assembled at EESC-USP in accordance to ASTM G154. The results have shown variations in punction and tear resistance after each period of exposure.

Levenberg-Marquardt application to two-phase nonlinear parameter estimation for finned-tube coil evaporators

A procedure for calculation of refrigerant mass flow rate is implemented in the distributed numerical model to simulate the flow in finned-tube coil dry-expansion evaporators, usually found in refrigeration and air-conditioning systems. Two-phase refrigerant flow inside the tubes is assumed to be one-dimensional, unsteady, and homogeneous. In themodel the effects of refrigerant pressure drop and the moisture condensation from the air flowing over the external surface of the tubes are considered. The results obtained are the distributions of refrigerant velocity, temperature and void fraction, tube-wall temperature, air temperature, and absolute humidity. The finite volume method is used to discretize the governing equations. Additionally, given the operation conditions and the geometric parameters, the model allows the calculation of the refrigerant mass flow rate. The value of mass flow rate is computed using the process of parameter estimation with the minimization method of Levenberg-Marquardt minimization. In order to validate the developed model, the obtained results using HFC-134a as a refrigerant are compared with available data from the literature.

Uso do pó da palha de carnaúba em compósitos de quitosana

In this work a biodegradable composite using the carnauba straw s powder as reinforcement on chitosan matrix polymeric were manufactured. Firstly, were carried out the chemistry characterization of the carnauba straw s powder before and after treatments with NaOH and hexane. Goering and Van Soest method (1970), flotation test, moisture absorption, FTIR, TG/DTG, DSC and SEM have also being carried out. Composites were developed with variations in granulometry and in powder concentrations. They were characterized by TG/DTG, SEM and mechanicals properties. The results of chemical composition showed that the carnauba straw s powder is composed of 41% of cellulose; 28,9% of hemicellulose and 14% of lignin.The flotation test have indicated that the chemical treatment with NaOH decreased the powder s hidrophilicity.The thermal analysis showed increased of thermal stability of material after treatments. The results of FTIR and SEM revealed the removal of soluble materials from the powder (hemicelluloses and lignin), the material became rougher and clean. The composites obtained showed that the mechanicals properties of the composites were decreased in respect at chitosan films, and the composites with the powder at 150 Mesh showed less variation in the modulus values. The speed test of 10 mm/min showed the better reproducibility of the results and is in agreement to the standard ASTM D638. The SEM analysis of fracture showed the low adhesion between the fiber/matrix. The increase of volume of powder in the composite caused a decrease in values of stress and strain for the samples with untreated powder and treated with hexane. The composite with 50% of the powder s treated in NaOH didn t have significant variation in the values of stress and strain as compared with the composites with 10% of the powder, showing that the increase in the volume of fiber didn t affect the stress and strain of the composite. Thereby, it is concluded that the manufacture of polymeric composites of chitosan using carnauba straw s powder can be done, without need for pre-treatment of reinforcement, become the couple of carnauba straw s powder-chitosan a good alternative for biodegradable composites

Cellulose nanowhiskers from coconut husk fibers: Effect of preparation conditions on their thermal and morphological behavior

Cellulose nanowhiskers were prepared by sulfuric acid hydrolysis from coconut husk fibers which had previously been submitted to a delignification process. The effects of preparation conditions on the thermal and morphological behavior of the nanocrystals were investigated. Cellulose nanowhisker suspensions were characterized by Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), thermogravimetric analysis (TGA) and X-ray diffraction. Results showed that it was possible to obtain ultrathin cellulose nanowhiskers with diameters as low as 5 nm and aspect ratio of up to 60. A possible correlation between preparation conditions and particle size was not observed. Higher residual lignin content was found to increase thermal stability indicating that by controlling reaction conditions one can tailor the thermal properties of the nanowhiskers. Published by Elsevier Ltd.

Straw decomposition of nitrogen-fertilized grasses intercropped with irrigated maize in an integrated crop-livestock system

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo comparativo entre a pirólise do polietileno de baixa densidade, utilizando vermiculita modificada e SBA-15

Catalytic processes are widely present in everyday life. This results in large number of studies seeking materials that may combine the low cost catalytic efficiency. Based on this assumption, the clays have long been used as catalysts, with its huge availability, diversity and possibility of improving their properties from structural changes, primarily responsible for this great use. Among the natural clays, vermiculite due to their characteristic properties (high cation exchange capacity and expansion), is suitable for various applications including as catalysts and catalyst supports. In this work, the acid leaching of clay vermiculite was performed, coming from Santa Luzia-PB, with nitric acid (2, 3 and 4 mol / L) and subsequent calcination of the materials obtained. The materials were named as Vx/400, where x is the acid concentration employed and 400 used in calcination temperature. The effectiveness of changes made was determined by XRD techniques, FT-IR, EDS, TG/DTG, nitrogen physisorption and DTP of n-butylamine. Acid leaching has improved some properties of the clay - specific area and acidity - but the control of the acid concentration used is of vital importance, since the highest concentration caused the partial destruction of vermiculite entailing a decline in their properties. For analysis of the catalytic activity of the modified clay was made a comparative study with the SBA -15 mesoporous materials, synthesized via hydrothermal method, using the pyrolysis of low density polyethylene (LDPE). The results showed that the acid plays a fundamental role in the conversion of the polymer into smaller molecules, the material V3/400 was more selective for the source monomer (ethylene) due to their increased acidity, which promotes more breaks bonds in the polymeric chain, while materials and V0/400 V2/400, lower acidity, showed higher selectivity to light hydrocarbons, the range of fuel (41.96 and 41.23%, respectively), due to less breakage and secondary condensation reactions chains; already V4/400 SBA-15/550 and resulted in lower percentages of light hydrocarbons and the partial destruction of the structure and low acidity, respectively, responsible for the inefficiency of materials

Yield, chemical composition and chlorophyll relative content of Tanzania and Mombaça grasses irrigated and fertilized with nitrogen after corn intercropping

Avaliou-se o efeito da ausência e da aplicação de três doses de nitrogênio (50, 100 e 200 kg ha-1 de N) e quatro épocas de corte no inverno/primavera (julho a outubro) sobre a produtividade de massa seca (PMS), os teores relativos de clorofila (ICF _ índice de clorofila foliar) e os teores de nutrientes digestíveis totais (NDT), proteína bruta (PB), fibra em detergente neutro (FDN), fibra em detergente ácido (FDA) e lignina, bem como suas respectivas correlações nos capins tanzânia e mombaça após o consórcio com milho em um Latossolo Vermelho distroférrico. O delineamento experimental utilizado foi o de blocos casualizados, em parcelas subdivididas, com quatro repetições. As maiores PMS ocorreram com o aumento do fotoperíodo (a partir de agosto), no entanto, as respostas à adubação nitrogenada ao longo dos cortes diferiram entre e dentre os capins. em sistema de integração lavoura-pecuária irrigado sob condições de cerrado, é tecnicamente viável o estabelecimento dos capins tanzânia e mombaça em consórcio com o milho no momento da semeadura ou por ocasião da adubação nitrogenada de cobertura, visto que, mesmo na ausência de adubação nitrogenada, foi produzida quantidade satisfatória de forragem, com PMS média de 2.000 kg ha-1 por corte na época de maior escassez de volumoso para os animais (inverno/primavera). A adubação nitrogenada após a colheita do milho eleva a PMS e melhora a composição bromatológica dos capins, com aumento dos teores relativos de clorofila e PB no inverno/primavera, além de aumento dos teores de NDT e redução dos teores de FDN e FDA até o mês de setembro. O índice de clorofila foliar pode ser utilizado para estimar a PMS e o teor de PB, bem como indicar a necessidade de adubação nitrogenada dos capins tanzânia e mombaça submetidos a corte.

Produtividade e valor nutricional de variedades de cana-de-açúcar sob diferentes fontes de fósforo

Due to the expansion of sugarcane in areas that are not traditional in it's cultivation, there is need of study the management of fertilizer, mainly phosphorus, since it's the nutrient that most limits the production in the tropics. The aim of this work was to evaluate the productivity and nutritional value of two varieties of sugarcane grown under different phosphorus sources, for three production cycles in North of Mato Grosso State, Brazil. The experimental design was randomized blocks in factorial scheme 4x2, with four replications. The sources of phosphorus used were bone meal, Arad phosphate and triple superphosphate at a dose of 100 kg P2O5 ha(-1), and a control without nutrient application at planting. The varieties of sugarcane were planted IAC86-2480 and SP79-1011. We evaluated the productivity of dry matter, dry matter content, neutral detergent fiber and acid detergent, lignin, cellulose, in vitro digestibility and crude protein of forage. The phosphorus sources provided higher yields during the first cycle of sugarcane and did not cause significant effect on productivity in subsequent cycles. Phosphorus fertilization did not cause significant changes in the nutritional value of sugarcane. The variety IAC86-2480 showed higher crude protein content in three cycles and higher dry matter yield in the first two cycles, compared to SP79-1011. Regarding the fiber constituents, both showed similar results.

Screening and Production Study of Microbial Xylanase Producers from Brazilian Cerrado

Hemicelluloses are polysaccharides of low molecular weight containing 100 to 200 glycosidic residues. In plants, the xylans or the hemicelluloses are situated between the lignin and the collection of cellulose fibers underneath. The xylan is the most common hemicellulosic polysaccharide in cell walls of land plants, comprising a backbone of xylose residues linked by beta-1,4-glycosidic bonds. So, xylanolytic enzymes from microorganism have attracted a great deal of attention in the last decade, particularly because of their biotechnological characteristics in various industrial processes, related to food, feed, ethanol, pulp, and paper industries. A microbial screening of xylanase producer was carried out in Brazilian Cerrado area in Selviria city, Mato Grosso do Sul State, Brazil. About 50 bacterial strains and 15 fungal strains were isolated from soil sample at 35 A degrees C. Between these isolated microorganisms, a bacterium Lysinibacillus sp. and a fungus Neosartorya spinosa as good xylanase producers were identified. Based on identification processes, Lysinibacillus sp. is a new species and the xylanase production by this bacterial genus was not reported yet. Similarly, it has not reported about xylanase production from N. spinosa. The bacterial strain P5B1 identified as Lysinibacillus sp. was cultivated on submerged fermentation using as substrate xylan, wheat bran, corn straw, corncob, and sugar cane bagasse. Corn straw and wheat bran show a good xylanase activity after 72 h of fermentation. A fungus identified as N. spinosa (strain P2D16) was cultivated on solid-state fermentation using as substrate source wheat bran, wheat bran plus sawdust, corn straw, corncob, cassava bran, and sugar cane bagasse. Wheat bran and corncobs show the better xylanase production after 72 h of fermentation. Both crude xylanases were characterized and a bacterial xylanase shows optimum pH for enzyme activity at 6.0, whereas a fungal xylanase has optimum pH at 5.0-5.5. They were stable in the pH range 5.0-10.0 and 5.5-8.5 for bacterial and fungal xylanase, respectively. The optimum temperatures were 55C and 60 A degrees C for bacterial and fungal xylanase, respectively, and they were thermally stable up to 50 A degrees C.

Parâmetros físico-químicos de estrelas com planetas na missão CoRoT

In the present study we compute the atmospheric parameters (Teff , log g and vmic, [Fe/H]) and chemical abundance of 16 ions (Fe I, Fe II, O I, Si I, Na I, Mg I, Al I, Ca I, Ti I, Co I, Ni I, Rb I, Zr I, Ba II, La II and Cr I) for 16 solar-like stars with masses between 0:8 and 1:2 Mfi aproximatedly, including 10 planet-host stars detected by the CoRoT Space Mission. For this study, we use data from the ESO public archive: (i) high resolution spectra (R 47000) from the UVES spectrograph on the VLT/UT2-ESO (for 7 stars, covering the wavelength range 3450-4515 Å and 5500-9400 Å) and (ii) high resolution spectra from HARPS spectrograph on the La Silla-ESO 3.60 m telescope (for 9 stars, covering the wavelength range 4200-6865 Å). Our spectral analysis is based on MARCS models of atmosphere and Turbospectrum spectroscopic tools. On the base of the computed parameters, the referred abundances appears to follow the same behavior of the solar curve abundances. Further, one observes a signifficant correlation between the abundance ratio [m/Fe] and condensation temperature (Tc) of refractory elements (Tc > 900 K). The behavior of the projected rotational velocity (v sin i) versus the computed abundances [m/Fe] is also analyzed, presenting no clear trends. This study oers additional constraints to trace the evolutive history of solar-like stars with planets, including the search for chemical dierences between stars with and without transit planets and anomalies in the studied abundances

Qualidade da Dieta Selecionada por Bovinos na Sub-Região da Nhecolândia, Pantanal

Objetivou-se com o estudo determinar o valor nutritivo da dieta selecionada por vacas de cria, numa área característica da sub-região da Nhecolândia, Pantanal, durante dois anos hidrológicos (outubro de 1997 a setembro de 1999). Mensalmente foram colhidas manualmente amostras das partes das principais forrageiras selecionadas por bovinos, identificadas por meio de observação direta, para análise de proteína bruta (PB), fibra em detergente neutro (FDN), fibra em detergente ácido (FDA) e lignina (LIG). A digestibilidade da matéria orgânica (DMO) da dieta foi avaliada em amostras fecais com o uso da espectrofotometria de reflectância no infravermelho proximal (NIRS). Houve efeito interativo de ano e época para todos os constituintes químicos analisados na dieta. O valor nutritivo da dieta selecionada por bovinos diminuiu no período de abril a junho, em ambos os anos estudados. As vacas apresentaram uma melhor condição corporal de setembro a março do ano hidrológico 1998/99, no qual a dieta apresentou valores médios de 60,4% de digestibilidade, 10% de PB; 40,20% de FDA; 71% de FDN e 6,0% de lignina, considerada adequada para obtenção de um desempenho reprodutivo satisfatório. Portanto, o valor nutritivo da dieta selecionada por bovinos na sub-região da Nhecolândia depende especialmente da intensidade e distribuição das chuvas, responsáveis pela maior ou menor presença de água nas unidades mais baixas, que possuem forrageiras de melhor qualidade.

Preference of Atta capiguara (Hymenoptera, Formicidae) for Different Grasses

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)