Large-scale isolation and purification of R-phycoerythrin from red alga Palmaria palmata using the expanded bed adsorption method

R-phycoerythrin, a light-harvesting protein in some marine algae, and can be widely used in medicine, was isolated and purified from a red alga, Palmaria palmata (Lannaeus) Kuntze, using the streamline column (expanded bed adsorption) combined with ion-exchange chromatography. Because the crude extract was applied to the column upwardly, the column would not be blocked by polysaccharides usually very abundant in the extract of marine alga, this kind of blockage could hardly lie overcome in ordinary chromatographic column. After applying the crude extract containing 0.5 mol/L (NH4)(2)SO4, (NH4)(2)SO4 solution of different concentrations (0.2 mol/L, 0.1 mol/L and 0.05 mol/L) was used to elute the column downwardly and the eluates were collected and desalted. The desalted eluates were then applied onto all ion-exchange chromatographic column loaded with Q-sepharose for further purification of the R-phycoerythrin. Through these two steps, the purity (OD565/OD280) of the R-phycoerythrin from P. palmata was up to 3.5, more than 3.2, the commonly accepted criterion for purity, and the yield of the purified R-phycoerythrin could reach 0.122 mg/g of frozen P. palmata, much higher than that of phycobiliproteins purified with the previous methods. The result indicated that the cost of R-phycoerythrin will drop down with the method reported in this article.

Three-stage transformation of chlorophyll transient fluorescence pattern under sustained dehydration and the discovery of critical water content in seaweeds

The chlorophyll fluorescence kinetics of marine red alga Grateloupia turutunt Yamada, green alga Ulva pertusa Kjellm and brown alga Laminaria japonica Aresch during natural sustained dehydration were monitored and investigated. The pulse amplified modulation (PAM) system was used to analyze the distinct fluorescence parameters during thallus dehydration. Results proved that the fluorescence kinetics of different seaweed all showed three patterns of transformation with sustained water loss. These were: 1) peak kinetic pattern (at the early stage of dehydration fluorescence enhanced and quenched subsequently, representing a normal physiological state). 2) plateau kinetic pattern (with sustained water loss fluorescence enhanced continuously but quenching became slower, finally reaching its maximum). 3) Platform kinetic pattern (fluorescence fell and the shape of kinetic curve was similar to plateau kinetic pattern). A critical water content (CWC) could be found and defined as the percentage of water content just prior to the fluorescence drop and to be a significant physiological index for evaluation of plant drought tolerance. Once thallus water content became lower than this value the normal peak pattern can not be recovered even through rehydration, indicating an irreversible damage to the thylakoid membrane. The CWC value corresponding to different marine species were varied and negatively correlated with their desiccation tolerance, for example. Laminaria japonica had the highest CWC value (around 90%) and the lowest dehydration tolerance of the three. In addition, a fluorescence "burst" was found only in red algae during rehydration. The different fluorescence parameters F-o, F-v and F-v, F-m were measured and compared during water loss. Both F-o and F-v increased in the first stage of dehydration but F-v/F-m. kept almost constant. So the immediate response of in vivo chlorophyll fluorescence to dehydration was an enhancement. Later with sustained dehydration F-o increased continuously while F-v decreased and tended to become smaller and smaller. The major changes in fluorescence (including fluorescence drop during dehydration and the burst during rehydration) were all attributed to the change in F-o instead of F-v This significance of F-o indicates that it is necessary to do more research on F-o as well as on its relationship with the state of thylakoid membrane.

Fine-grained Pleistocene deepwater turbidite channel system on the slope of Qiongdongnan Basin, northern South China Sea

Recently, as oil exploitation has become focused on deepwater slope areas. more multi-channel high resolution 2D and 3D seismic data were acquired in the deepwater part of the Qiongdongnan Basin, northern South China Sea. Based on 3D seismic data and coherence time slice, RMS and 3D visualization, a series of deepwater channels were recognized on the slope that probably developed in the late Quaternary period. These channels trend SW-NE to W-E and show bifurcations, levees, meander loops and avulsions. High Amplitude Reflections (HARs), typical for channel-levee complexes, are of only minor importance and were observed in one of the channel systems. Most of the detected channels are characterized by low-amplitude reflections, and so are different from the typical coarse-grained turbidite channels that had been discovered worldwide. The absence of well data in the study area made it difficult to determine the age and lithology of these channels. Using a neighboring drill hole and published data about such depositional systems worldwide, the lithology of these channels is likely to be dominated by mudstones with interbedded thin sandstones. These channels are formed by turbidity currents originated from the little scale mountain river of mid-Vietnam in SW direction and were probably accompanied by a relative sea level drop in the last glacial age. These channels discovered on the northern South China Sea slope are likely to be fine-grained, mud-dominant and low N:G deposits in a deepwater paleogeographic setting. (C) 2009 Elsevier Ltd. All rights reserved.

Seismic stratigraphy of the Qiongdongnan deep sea channel system, northwest South China Sea

Based on more than 4000 km 2D seismic data and seismic stratigraphic analysis, we discussed the extent and formation mechanism of the Qiongdongnan deep sea channel. The Qiongdongnan deep sea channel is a large incised channel which extends from the east boundary of the Yinggehai Basin, through the whole Qiongdongnan and the Xisha trough, and terminates in the western part of the northwest subbasin of South China Sea. It is more than 570 km long and 4-8 km wide. The chaotic (or continuous) middle (or high) amplitude, middle (or high) continuity seismic facies of the channel reflect the different lithological distribution of the channel. The channel formed as a complex result of global sea level drop during early Pliocene, large scale of sediment supply to the Yinggehai Basin, inversion event of the Red River strike-slip fault, and tilted direction of the Qiongdongnan Basin. The large scale of sediment supply from Red River caused the shelf break of the Yinggehai Basin to move torwards the S and SE direction and developed large scale of prograding wedge from the Miocene, and the inversion of the Red River strike-slip fault induced the sediment slump which formed the Qiongdongnan deep sea channel.

Paleoenvironmental change in the middle Okinawa Trough since the last deglaciation: Evidence from the sedimentation rate and planktonic foraminiferal record

Well-dated, high-resolution records of planktonic foraminifera and oxygen isotopes from two sediment cores, A7 and E017, in the middle Okinawa Trough reveal strong and rapid millennial-scale climate changes since similar to 18 to 17 thousand years before present (kyr B.P.). Sedimentation rate shows a sudden drop at similar to 11.2 cal. kyr B.P. due to a rapid rise of sea level after the Younger Dryas (YD) and consequently submergence of the large continental shelf on the East China Sea (ECS) and the retreat of the estuary providing sediment to the basin. During the last deglaciation, the relative abundance of warm and cold species of planktonic foraminifera fluctuates strongly, consistent with the timing of sea surface temperature (SST) variations determined from Mg/Ca measurements of planktonic foraminifera from one of the two cores. These fluctuations are coeval with climate variation recorded in the Greenland ice cores and North Atlantic sediments, namely Heinrich event 1 (H1), Bolling-Allerod (B/A) and YD events. At about 9.4 kyr B.P., a sudden change in the relative abundance of shallow to deep planktonic species probably indicates a sudden strengthening of the Kuroshio Current in the Okinawa Trough, which was synchronous with a rapid sea-level rise at 9.5-9.2 kyr B.P. in the ECS, Yellow Sea (YS) and South China Sea (SCS). The abundance of planktonic foraminiferal species, together with Mg/Ca based SST, exhibits millennial-scale oscillations during the Holocene, with 7 cold events (at about 1.7, 2.3-4.6, 6.2, 7.3, 8.2, 9.6, 10.6 cal. kyr BP) superimposed on a Holocene warming trend. This Holocene trend, together with centennial-scale SST variations superimposed on the last deglacial trend, suggests that both high and low latitude influences affected the climatology of the Okinawa Trough. (c) 2006 Elsevier B.V. All rights reserved.

评价水产动物生长性能的生理生化指标和分子生物学指标

以奥利亚罗非鱼(Oreochromis aureus)为实验对象，设计了3种不同的摄食类型，分别是鲜活饵料组、饥饿3周后饱食投喂组和人工饲料组。鲜活饵料组投喂冰冻赤子爱胜蚓，利用蚯蚓体内丰富的营养成分和活性物质，以期获得奥利亚罗非鱼良好的生长状况；饥饿后饱食组是指饥饿3周后，以人工饲料饱食投喂2周，用于研究饥饿与补偿生长获得快速生长时血液理化指标的变化情况；人工饲料组作为对照组。纯淡水条件下养殖，水温25±2℃。测定了奥利亚罗非鱼在3种摄食类型饲喂下某些血液生理生化指标变化的情况，并将指标变化情况与增重率做相关性分析，试图找出能够反映奥利亚罗非鱼生长性能的血液生理生化指标。 研究结果表明，奥利亚罗非鱼在饥饿3周后获得了补偿生长，补偿生长时的增重率和特定生长率显著高于人工饲料组(P<0.05)，高于鲜活饵料组，但差别不显著；相关性分析研究表明血清总蛋白、胆固醇、四碘甲状腺原氨酸（T4）与增重率极显著相关(P<0.01)，血红蛋白显著相关(P<0.05)，红细胞、白细胞、碱性磷酸酶高度相关(相关系数为0.580、0.551和0.557)，因此，建议血清总蛋白、胆固醇和血红蛋白可作为能够反映罗非鱼生长性能的新指标。 根据序列设计引物，PCR反应条件：变性温度：95 ℃，3 min；退火温度：57℃，20 sec；延伸温度：72℃，5 min，共36个循环，从牙鲆、黑鲪和鲈鱼中克隆出胰岛素样生长因子（IGF-Ⅰ）部分序列，首次证实了IGF-Ⅰ在3种海水鱼中的存在。 利用蛋氨酸与ZnSO4•7H2O，在pH 5.5、80℃下，反应1小时，采用蛋氨酸与硫酸锌2：1的配料比，合成出了产物蛋氨酸螯合锌，蛋氨酸螯合锌外观白色，粉状，室温下微溶于水，不溶于乙醇，并用原子吸收光谱法测定其含锌量为15%，螯合率为88.2%。

Simultaneous Determination of Multi-Organotin Compounds in Seawater by Liquid-Liquid Extraction-High Performance Liquid Chromatography-Inductively Coupled Plasma Mass Spectrometry

The hyphenated technique of high performance liquid chromatography coupled with inductively coupled plasma mass spectrometry (HPLC-ICP-MS) was applied to the simultaneous determination of five organotin compounds (trimethyltin, dibutyltin, tributyltin, diphenyltin and triphenyltin) in seawater samples. Agilent TC-C18 column was used for the separation, the mobile phase of HPLC was CH3CN : H2O: CH3COOH=65 : 23 : 12 (phi), 0.05% TEA, and pH value was adjusted to 3.0 by diluent ammonia. The flow rate was 0.6 mL . min(-1). Five mixed organotin compounds in a mix standard solution from 100 to 0.5 mu g . L-1 were applied for the method assessment. The experimental results indicate that the correlation coefficient of calibration curves (R-2) for each organotin compound was over 0.998 and the detection limits of the five organotin compounds were lower than 3 ng . L-1. Different mixed organic solvents including dichloromethane or toluene were used for extraction of organotin and the extraction condition of organotin from seawater was optimized. The 100 mL seawater acidized by hydrochloric acid was extracted by 10 mL carbon dichloride (CH2Cl2) with 2% tropolone for 10 min twice. Extracted organic solvents were mixed And blown to one drop by nitrogen with the rate of 1.7 mL . min(-1), then 1 mL acetonitrile was added to the drop for redissolving the organotin compounds. Finally, the mixed redissolution was filtered by 0.22 mu m organic filter membrane before analysis. it was found that the only organotin compound in seawater was triphenyltin (TPHT) and the content was 53.2 ng . L-1. The recoveries test from the standard addition for diphenyltin (DPHT), dibutyltin (DBT), tributyltin (TBT) and triphenyltin (TPHT) were over 80%. However, the recovery for trimethyltin (TMT) was relatively low and the value was 50%. The reason might be attributed to the decomposition or adsorption of those compounds during the extraction procedure. Further study on this subject is in progress.

Study on corrosion of steels in marine environment by corrosion simulation device

Three kinds of steels were studied using electrically connected hanging specimen in the corrosion simulation device and offshore long scale hanging specimen. The experimental results obtained by the two methods show that the device can better reflect the offshore corrosion environment. A Ni-Cu-P steel specimen was studied through analysis of the specimen's corrosion products and corrosion types. The surface of the samples before and after the removal of the rust layer produced by these two methods were observed and compared after some experiments. The microstructure of the corrosion products under different marine environments were analyzed and compared through IR. It indicated good correlation between the electrically connected hanging specimen method and the long scale hanging specimen method.

Study on corrosion simulation device for marine structural steel

A corrosion simulation device was studied using offshore long scale hanging specimens. An Ni-Cu-P steel specimen was studied by analysing its corrosion products and corrosion types. The appearance of the samples and the surface of the metallic substrate after the removal of the rust layer produced by these two methods were observed and compared after 470 days of exposure. The phase structure of the corrosion products under different marine environments were analysed and compared. It further indicated good correlation between the electrically connected hanging specimen method and the long scale hanging specimen method.

Study on steel corrosion in different seabed sediments

A series of simulation experiments on carbon steel (A(3) steel) and low alloy steel (16 Mn steel) in marine atmosphere (MA), seawater (SW) and seabed sediment (SBS) including rough sea sand, fine sea sand and seabed mud were carried out indoors for a year or so by means of individually hanging plates (IHP) and electrically connected hanging plates (ECHP). The corrosion of steels in SBS was mainly due to the macrogalvanic cell effect. The steel plates at the bottom of SBS, as the anode of a macrogalvanic cell, showed the heaviest corrosion with a corrosion rate of up to 0.12 mm/a, approximately equal to that of steel plates in marine atmosphere. The test results showed that the corrosion rates of A(3) and 16 Mn steel in marine environment were in the order: MA > SW > SBS by the IHP method; and MA > SBS > SW by the ECHP method. The corrosion rates of steels in the water/sediment interface were directly proportional to the grain size of the SBS by the ECHP method, but those of steels in the water/sediment interface did not vary with the grain size of SBS by the IHP method. The corrosion rate of low-alloy steel was a little higher than that of carbon steel. The results of this study have important applications for design of offshore steel structures such as oil platform, pier, and port.

水下机械手液压控制系统动力机构参数的分析计算

本文所介绍的水下机械手液压控制系统为一典型的具有变回油压力封闭式系统。文中阐述了此种系统液压动力机构的设计原理及静、动态参数的分析计算方法。对于在变回油压力下,由四通阀控制的非对称油缸的静态特性进行了详细的分析。给出了在不同回油压力下,不同面积比的非对称油缸、阀的负载压降及最大空载流量的变化规律。这对于确定水下机械手的液压动力机构的参数提供了依据。

海上时移地震综合解释技术研究与应用

The practical application and development of the time-lapse seismic reservoir monitor technology has indicated which has already become one of most important development technologies in seeking the surplus oil distribution and improving the reservoir recovering. The paper, first obtained the rock physics experiment analysis data according to the Bohai Sea loose sandstone in-situ measure technical, and determined the feasibility research of the S oil-field on the time-lapse seismic reservoir monitoring combining with the time-lapse numeric simulation technology, which was used to analyze the time-lapse seismic respond raw of the reservoir parameters change and pointed out the attentive problems during the real time-lapse seismic processing and interpretation. Next, simply introduced the technical link and the effect of the time-lapse mutual constrained fidelity and match processing aiming at the local complex gathering condition, geological condition, development engineering condition. Third, introduced the time-lapse integrated interpretation and the technical system with the innovative key technology that includes the time-lapse difference explanation technology, the time-lapse seismic multi-attributes integrated interpretation technology, and the time-lapse constrained reservoir parameters inversion technology, and so on. Using the time-lapse difference direct explanation technology, directly obtained the surplus oil macroscopic distribution through the difference seismic data; Using the presenting 8 big principles of the sublayer isochronisms comparison, carried on the time-lapse integrated interpretation analysis on the fine sublayer comparison and the thin oil-layer(group) contrast and the oil layer (group); The paper putted up the research, contrast, applications of the multi-sides sensitive attribute analysis and the RBF nerve network on the nearest study algorithm, and predicted the reservoir parameters and the surplus oil distribution with them; Combining with innovative researches and the time-lapse seismic constrained reservoir parameters inversion technology realized the good combination of the seismic and the reservoir engineering. Fourth, under fully analyzing the geology condition, the reservoir condition, the exploit dynamic data, and the seismic data of the S oil-field, and analyzing the time-lapse difference factors with reservoir dynamic exploit data, calibrated the oil-gas saturation change, the pressure change, the water saturation change, and determined the rationality of the time-lapse seismic difference, and finally obtained the surplus oil distribution, the water flood characteristic understanding, reservoir degasification, and pressure drop raw, and so on, which had been used in the well pattern tightening plan proof of the S oil-field development adjustment plan. Finally, the paper summarized the knowledge and understanding of the marine time-lapse seismic integrated interpretation, also had pointed out the further need researched question.

金川镍矿岩体移动与开采稳定性研究

The two major issues in mining industry are work safety and protection of ground environment when carrying on underground mining activities. Cut-and-fill mining method is increasingly applied in China owing to its advantages of controlling ground pressure and protecting the ground environment effectively. However, some cut-and-fill mines such as Jinchuan nickel mine which has big ore body, broken rock mass and high geostress have unique characteristics on the law of ground pressure and rock mass movement that distinguish from other mining methods. There are still many problems unknown and it is necessary for the further analysis. In this dissertation, vast field survey, geology trenching and relative data analysis are carried out. The distribution of ground fissures and the correlation of the fissures with the location of underground ore body is presented. Using of monitoring data by three-dimension fissure meter and GPS in Jinchuan Deposit Ⅱ, the rule of the surface deformation and the reason of ground fissures generation are analyzed. It is shown that the stress redistribution in surrounding rocks resulting from mining, the existence of the void space underground and the influence of on-going mining activities are three main reasons for the occurrence of ground fissures. Based on actual section planes of No.1 ore body, a large-scale 3D model is established. By this model, the complete process of excavation and filling is simulated and the law of rock mass movement and stability caused by Cut-and-fill Mining is studied. According to simulation results, it is concluded that the deformation of ground surface is still going on developing; the region of subsidence on the ground surface is similar with a circle; the area on the hanging wall side is larger than one on the lower wall side; the contour plots show the centre of subsidence lay on the hanging wall side and the position is near the ore body boundary of 1150m and 1250m where ore body is the thickest. Along strike-line of Jinchuan Deposit Ⅱ, the deformation at the middle of filling body is larger than that in the two sides. Because of the irregular ore body, stress concentrates at the boundary of ore body. With the process of excavation and filling, the high stress release and the stress focus disappear on the hanging wall side. The cut-and-fill mechanism is studied based on monitoring data and numerical simulation. The functions of filling body are discussed. In this dissertation, it is concluded that the stress of filling body is just 2MPa, but the stress of surrounding rock mass is 20MPa. We study the surface movement influenced by the elastic modulus of backfill. The minimal value of the elastic modulus of backfill which can guarantee the safety production of cut-and-fill mine is obtained. Finally, based on the real survey results of the horizontal ore layer and numerical simulation, it is indicated that the horizontal ore layer has destroyed. Key words: cut-and-filling mining, 3D numerical simulation, field monitoring, rock mass movement, cut-and-filling mechanism, the elastic modulus of backfill, the horizontal ore layer

华北克拉通孔玆岩系中石榴子石花岗岩的成因：熔体与残留相混合机制的研究

The most widespread rock associations in the Western Block of North China Craton are khondalites distributed mainly in Jining, Liangcheng and Datong. A large quantitiy of garnet-bearing granites are contained in the khondalites. A great deal of research has been carried out on them by previous researchers. Studies of these garnet-bearing granites consist essentially of structural characteristics, petrography and geochemistry, and finally geochronological determinations. Summing up these researches, it will not be difficult to see that all of these authors have regarded these large numbers of garnets (up to 20%) contained in granites as crystallized products from magmas, but they have not proved this from petrological perspective. Theoretically, there are possibly three kinds of petrogenesis as to these garnets. The first one is that they have been transferred to the granites from khondalites by melt when anatexis happened to khondalites, and they, in essence, are residual metamorphic garnets; The second one is that when the khondalites were being melted, these garnets were produced from biotite dehydration melting, and the newly formed garnets intruded together with the melt and eventually molded the garnet-bearing granites. Garnets of this possible kind either showed independent crystals, or garnets from khondalites took place secondary growth under favorable temperature and pressure conditions for their crystallization; The last possibility is that these garnets were crystallized from magmas in which suitable pressure, temperature and composition were available. These garnets, generally, should be fine-grained. The aim of this study is, through examining the mineral chemistry of the garnets and the whole rock chemistry, to ascertain under which kind of mechanism, in the world, did these garnets form? Besides, we try to calculate the temperatures under which khondalites began melting and reactions of the garnets and the cooled melts happened by garnet-biotite thermometry. The whole rock chemistry analyses of the garnet-bearing granites tell us that all the samples are strongly peraluminous (A/CNK greater than 1.1) on the A/NK vs. A/CNK plot. On the SiO2-K2O plot, the granites are mainly constrained to be high-K calc-alkaline and calc-alkaline series, consistent with previous researches. On the ACF（（Al2O3-Na2O-K2O）-FeO(T)-CaO） discrimination plot, all the six garnet-bearing granite samples drop into the area of S-type granites. The relationship between CaO/Na2O and SiO2 shows that the overwhelming majority of garnet-bearing granites have a CaO/Na2O value over 0.3, revealing that they probably come from metagreywacke precursors or mediate-felsic orthogeneisses compositionally similar to them. Detailed EPMA analyses conducted on the garnets contained in the garnet-bearing granites show that all the garnets are dominated by almandine and pyrope, which occupy 92-96% (Weight Percentage) of each garnet analyzed, typical of granulite facies. Their chemical composition is entirely different from those crystallized in magmas, but extremely similar to those of typical granulite facies metapelites in khondalites and typical granulites, indicating all the garnets to be metamorphogenic. In addition, REEs distribution patterns of the garnets are totally different from typical biotite granites and peraluminous granites. In other words, both LREE and HREE of our garnets are evidently lower than those from these two kinds of rocks. Moreover, compared to the REE pattern of the garnets from typical amphibolites, LREE content of our garnets is obviously higher and HREE content is a little lower. However, REE patterns of our garnets are completely in harmony with those of garnets from typical granulites. So, the REE patterns of garnets, again, prove that all the garnets we studied are metamorphogenic. Biotites appear in two forms, being as inclusions in the garnet and as selvages immediately adjacent to the garnet, respectively. Two reactions and their corresponding temperatures, with the help of petrography and Garnet-Biotite geothermometers, could be obtained, which are Bt+ Pl+ Qtz→Kfs+ Opx+ Grt+ melt as positive reaction and Kfs+ Grt+ melt→Bt+ Pl+ Qtz as reverse reaction, respectively. Summing up the discussion above, we declare that the garnet-bearing granites distributed in the Western Block of North China Craton are the mixture of melts and restites resulted from biotite dehydration melting. The garnets contained in the restites are the products from biotite dehydration melting and restites from the khondalites, respectively.

鄂尔多斯盆地东部地区奥陶系马家沟组沉积相与储层特征研究

Ordos Basin is one of the primary bases for petroleum exploration in our country. A series of Ordovician large gas fields were discovered, which suggest that the Lower Paleozoic carbonate, especiallly for Ordovician carbonate rocks, preserve plenty of hydrocarbon resources. Well Longtong 1 is studied as the typical exploration well. Acorrding to the specific research on the type of lithology, texture, structure and sedimentary sequence in Ordovician Majiagou Formation as well as additional data from another 20 wells, the sedimentary model has been built in Majiagou Formation. The sedimentary characteristics for each Member in Majiagou Formaiton and the feature of distribution are well understood as below: It suggests that period of Member 1, Member 3 and Member 5 in Majiagou Formation characterize with dry and hot climate as well as drop of the sea level. The area of Well Longtan 1 in the eastern basin is abundant of platform evaporite lithofacies with the depositional anhyrock and salt rock, whereas yield a suite of dolomite intercalated by the thin layers of anhyrock from the anhyrcok-dolomite platform sediment. It deposits muddy dolomite, dolomitic limestone and fine-grain dolomite in limestone-dolomite platform and restricted sea. During the stage of Member 2 and Member 4 in Majiagou Formation, the climate is wet and hot with increasing sea level. The study region occurs limestone with little dolomite in the open sea environment; but the margin area is the restricted sea settings with interbeding dolomite and limestone. Based on the thin section identification, element and isotope analysis as well as the study of texture and structure, it sugguests that the main reserviors are dolomite while the gypsum are major cap rocks. The Member 2 in Majiagou Formation is both the source rocks and the resveroirs; gypsum rocks widely occur in Member 3 as the better cap; similar to the Member 2, the Member 4 in Majiagou Formation is both the source rocks and the resveroirs; there are two source-reservoir-cap assemblages in the Member 5 alone and the cap is gypsum with high quality and great thickness, which is a favorite source-reservoir-cap assemblage.