Stochastic modelling of flexible manufacturing systems

Mathematical modelling plays a vital role in the design, planning and operation of flexible manufacturing systems (FMSs). In this paper, attention is focused on stochastic modelling of FMSs using Markov chains, queueing networks, and stochastic Petri nets. We bring out the role of these modelling tools in FMS performance evaluation through several illustrative examples and provide a critical comparative evaluation. We also include a discussion on the modelling of deadlocks which constitute an important source of performance degradation in fully automated FMSs.

Thermodynamic modelling of absorption-resorption heating cycles with some new working pairs

This paper presents the results of a thermodynamic cycle analysis of single stage resorption heat pump (RHP) and resorption heat transformer (RHT) cycles with the new working pairs R22-NMP and R22-DMA. The coefficients of performance (COP) are correlated with the low grade source temperature, temperature at which useful heat is obtained and ambient temperature. The COPs are in the range 1.20–1.60 for the RHP mode and 0.25–0.45 for the RHT mode. Absorber temperatures (useful temperatures) as high as 50°C in the RHP mode and 87°C in the RHT mode have been obtained. It is observed that absorption-resorption systems are inflexible in their range of operating temperature and necessitate a higher pump work as compared with simple single-stage absorption heating systems. However, single stage RHTs show higher temperature boosts than simple absorption heat transformers.

SCF and electron correlation studies on structure, force constants and vibrational spectra of borane monoammoniate complex

Effects of basis set and electron correlation on the equilibrium geometry, force constants and vibrational spectra of BH3NH3 have been studied. A series of basis sets ranging from double zeta to triple zeta including polarization and diffuse functions have been utilized. All the SCF based calculations overestimate the dative B-N bond distance and considerable improvement occurs when the treatment for electron correlation is introduced. Detailed vibrational analysis for BH3NH3 has been carried out. The mean absolute percentage deviation of the ab initio predicted vibration frequencies of (BH3NH3)-B-11 from the experiment is about 10% for the SCF based calculations and the MP2 method shows better agreement, the overall deviation being 5-6%. The ground state effective force constants of BH3NH3 were obtained using RECOVES procedure. The RECOVES sets of force constants are found to be highly satisfactory for the prediction of the vibrational frequencies of different isotopomers of BH3NH3. The mean absolute percentage deviation of the calculated frequencies of different isotopomers from the experiment is much less than 1%. The RECOVES-MP2/augDZP set of force constants was found to be the best set among the different sets for this molecule. Theoretical infrared intensities are in fair agreement with the observed spectral features.

Theoretical Analysis of the Electromotive Force of a Cell Incorporating a Composition Gradient Solid Electrolyte

New composition gradient solid electrolytes have been designed for application in high temperature solid-state galvanic sensors and in thermodynamic measurements. The functionally gradient electrolyte consists of a solid solution between two or more ionic conductors with a common ion and gradual variation in composition of the other ionic species. Unequal rates of migration of the ions, caused by the presence of the concentration gradient, may result in the development of space charge, manifesting as diffusion potential. Presented is a theoretical analysis of the EMF of cells incorporating gradient solid electrolytes. An analytical expression is derived for diffusion potential, using the thermodynamics of irreversible processes, for different types of concentration gradients and boundary conditions at the electrode/electrolyte interfaces. The diffusion potential of an isothermal cell incorporating these gradient electrolytes becomes negligible if there is only one mobile ion and the transport numbers of the relatively immobile polyionic species and electrons approach zero. The analysis of the EMF of a nonisothermal cell incorporating a composition gradient solid electrolyte indicates that the cell EMF can be expressed in terms of the thermodynamic parameters at the electrodes and the Seebeck coefficient of the gradient electrolyte under standard conditions when the transport number of one of the ions approaches unity.

Mathematical modelling of neurons and neural networks

The basic concepts and techniques involved in the development and analysis of mathematical models for individual neurons and networks of neurons are reviewed. Some of the interesting results obtained from recent work in this field are described. The current status of research in this field in India is discussed

Modelling plane mixing layers using vortex points and sheets

We present here a critical assessment of two vortex approaches (both two-dimensional) to the modelling of turbulent mixing layers. In the first approach the flow is represented by point vortices, and in the second it is simulated as the evolution of a continuous vortex sheet composed of short linear elements or ''panels''. The comparison is based on fresh simulations using approximately the same number of elements in either model, paying due attention in both to the boundary conditions far downstream as well as those on the splitter plate from which the mixing layer issues. The comparisons show that, while both models satisfy the well-known invariants of vortex dynamics approximately to the same accuracy, the vortex panel model, although ultimately not convergent, leads to smoother roll-up and values of stresses and moments that are in closer agreement with the experiment, and has a higher computational efficiency for a given degree of convergence on moments. The point vortex model, while faster for a given number of elements, produces an unsatisfactory roll-up which (for the number of elements used) is rendered worse by the incorporation of the Van der Vooren correction for sheet curvature.

Mathematical modelling of divided blast cupola

A pseudo 2-D mathematical model has been developed to simulate a cupola with one row and two rows of tuyere. The simulation results predicted higher spout temperature and combustion ratio for cupola with two rows of tuyere compared to that with one row. Further, the model has been used to study the effect of the distance of separation between the two rows of tuyere on cupola performance. The computed results shows that the spout temperature increases with tuyere level separation and attains the maximum at an optimum distance of separation between two rows of tuyere. Above the optimum, the spout temperature starts decreasing. The exit gas temperature and combustion ratio increases monotonously with the increase in tuyere level separation. These results agree well with the reported experimental observations. The mechanism behind the improved cupola performance with two rows of tuyere has been deduced from the computed temperature and composition profiles inside the cupola.

Modelling transport processes during microwave heating: A review

The review is concerned with models that analyze transport:processes that occur during microwave heating. Early models on microwave. heating used Lambert's law to describe the microwave power absorption. Over the last decade, models for transport processes have been developed with the microwave power derived from Maxwell's equations. Those models, primarily based on plane waves, have been used for analyzing microwave heating of solids, liquids, emulsions, microwave thawing and drying. The models illustrate phenomena such a resonances, hot spots, edge and runaway heating. The literature on microwave sintering, susceptor heating and microwave assisted synthesis is largely experimental in nature and only key issues are highlighted. To fully appreciate the models for microwave heating, a section on the theory of electromagnetic wave propagation is included, where expressions for the electric field in dielectric slabs and cylinders are presented.

Simulation and modelling of orbital debris environment by equivalent breakups

It is well known that the increasing space activities pose a serious threat to future missions. This is mainly due to the presence of spent stages, rockets spacecraft and fragments which can lead to collisions. The calculation of the collision probability of future space vehicles with the orbital debris is necessary for estimating the risk. There is lack of adequately catalogued and openly available detailed information on the explosion characteristics of trackable and untrackable debris data. Such a situation compels one to develop suitable mathematical modelling of the explosion and the resultant debris environment. Based on a study of the available information regarding the fragmentation, subsequent evolution and observation, it turns out to be possible to develop such a mathematical model connecting the dynamical features of the fragmentation with the geometrical/orbital characteristics of the debris and representing the environment through the idea of equivalent breakup. (C) 1997 COSPAR.

Volume modelling for emerging manufacturing technologies

The next generation manufacturing technologies will draw on new developments in geometric modelling. Based on a comprehensive analysis of the desiderata of next generation geometric modellers, we present a critical review of the major modelling paradigms, namely, CSG, B-Rep, non-manifold, and voxel models. We present arguments to support the view that voxel-based modellers have attributes that make it the representation scheme of choice in meeting the emerging requirements of geometric modelling.

Modelling electricity demand with representative load curves

Models for electricity planning require inclusion of demand. Depending on the type of planning, the demand is usually represented as an annual demand for electricity (GWh), a peak demand (MW) or in the form of annual load-duration curves. The demand for electricity varies with the seasons, economic activities, etc. Existing schemes do not capture the dynamics of demand variations that are important for planning. For this purpose, we introduce the concept of representative load curves (RLCs). Advantages of RLCs are demonstrated in a case study for the state of Karnataka in India. Multiple discriminant analysis is used to cluster the 365 daily load curves for 1993-94 into nine RLCs. Further analyses of these RLCs help to identify important factors, namely, seasonal, industrial, agricultural, and residential (water heating and air-cooling) demand variations besides rationing by the utility. (C) 1999 Elsevier Science Ltd. All rights reserved.

Modelling of a patch repair to a thin cracked sheet

Integrity enhancement of damaged or design deficient structures through repairs is attracting considerable engineering attention. Bonded composite patch repairs to cracked metallic sheets offer various advantages over riveted doubler type, particularly for airframe applications. This paper first reviews the R&D activity in the area of structural repairs. It then approaches the problem of a composite patch repair to a cracked aluminium sheet with different finite element modelling strategies and compares their outcome. The efficient finite element modelling approach thus established is used to study the effect of patch material, patch size, patch symmetry and adhesive thickness on repair performance as the crack grows in the repair configuration. (C) 1999 Elsevier Science Ltd. All rights reserved.