Spin-Dynamics in Cold Gases of 87Rb and Atomic Hydrogen. The spins they are a-changin’

In this thesis the dynamics of cold gaseous atoms is studied. Two different atomic species and two different experimental techniques have been used. In the first part of the thesis experiments with Bose-Einstein condensates of Rb-87 are presented. In these experiments the methods of laser cooling and magnetic trapping of atoms were utilized. An atom chip was used as the experimental technique for implementation of magnetic trapping. The atom chip is a small integrated instrument allowing accurate and detailed manipulation of the atoms. The experiments with Rb-87 probed the behaviour of a falling beam of atoms outcoupled from the Bose-Einstein condensate by electromagnetic field induced spin flips. In the experiments a correspondence between the phases of the outcoupling radio frequency field and the falling beam of atoms was found. In the second part of the thesis experiments of spin dynamics in cold atomic hydrogen gas are discussed. The experiments with atomic hydrogen are conducted in a cryostat using a dilution refrigerator as the cooling method. These experiments concentrated on explaining and quantifying modulations in the electron spin resonance spectra of doubly polarized atomic hydrogen. The modifications to the previous experimental setup are described and the observation of electron spin waves is presented. The observed spin wave modes were caused by the identical spin rotation effect. These modes have a strong dependence on the spatial profile of the polarizing magnetic field. We also demonstrated confinement of these modes in regions of strong magnetic field and manipulated their spatial distribution by changing the position of the field maximum.

Work-related crisis exposure : psychological trauma and PTSD in news journalists

I avhandlingen undersöktes hur journalister själva reagerar efter att ha arbetat med en plötslig krissituation, samt vilka faktorer som kan bidra till en förhöjd risk för allvarliga långsiktiga stressymptom. Temat undersöktes (1) genom att se på hur journalisters tidigare erfarenheter av krisuppdrag och traumatiska upplevelser i privatlivet var relaterade till stressymptom (posttraumatiskt stressyndrom, sekundär traumatisk stress, depression och utmattningssyndrom), och (2) genom att studera riskfaktorer i en identifierad typ av kris, de finländska skolskjutningarna 2007-08. Avhandlingens resultat baserades på enkätsvar från finländska nyhetsjournalister (N = 503) och intervjuer med personer som jobbat på plats vid skolskjutningar (N = 28). En klar majoritet av journalisterna hade inte allvarliga långsiktiga stressymptom vid tiden för undersökningen. De som varit på ett tidigare krisuppdrag där man bevittnat många obehagliga detaljer hade fler allvarliga stressymptom. En annan riskfaktor var att ha ett förflutet med fler traumatiska händelser i privatlivet. Bland de som arbetat med skolskjutningar var starka kortsiktiga reaktioner, t.ex. hjälplöshet och chock, relativt vanliga. Reaktionerna hörde ändå oftast till den normala återhämtningsprocessen, och ledde inte till en långsiktig försämring av måendet. Journalister som i hög grad identifierade sig med krisen, t.ex. personer med egna barn, hade större risk för att drabbas av allvarliga symptom på lång sikt. Detsamma gällde de som på plats upplevt journalistiska etiska dilemman, t.ex. att beordras av överordnade till uppdrag som gick emot egna principer. För att förebygga psykisk stress bland journalister är det viktigt att inom branschen sprida kunskap om stressreaktioner och utveckla rekommendationer för etisk krisjournalistik. Därmed kan journalister få bättre verktyg för att minimera risken att via sitt yrkesutövande orsaka ytterligare skada åt krisdrabbade.

Work for your happiness - Theoretical and empirical study defining and measuring happiness at work

There are vast changes in the work environment, and the traditional rules and management methods might not be suitable for today’s employees anymore. The meaning of work is also changing due to the younger and higher educated generations entering the markets. Old customs need to be re-validated and new approaches should be taken into use. This paper strongly emphasizes the importance of happiness research and happiness at work. The values towards the meaning of work are changing; people demand happiness and quality from all aspects of their lives. The aim of this study is to define happiness - especially at work - and to explain how it can be measured and what kind of results achieved. I also want to find out how the contents of work and the working environment might enhance happiness. The correlation between education and happiness is discussed and examined. I am aware that the findings and theories are concentrating mainly on Western Countries and highlighting the values and work-environments of those societies. The main aim of the empirical study is to find out if there are connections between happiness and work in data collected by World Value Survey in 2005, and if the profession has effects on happiness. Other factors such as the correlation of age, sex, education and income are examined too. I also want to find out what kind of values people have towards work and how these affect the happiness levels. The focus is on two nations: Finland (N=1014) and Italy (N=1012). I have also taken the global comparison within, that is all 54 countries (N=66,566) included in the 5th wave (during the years 2005 -2008) of the World Value Survey. The results suggest that people are generally happy around the world; happiness decreasing with the age, the educated being happier than the uneducated and the employed happier than the unemployed. People working in neat “white collar” jobs are more likely happier than those working in factories or outdoors. Money makes us happier, until certain level is reached. Work is important to people and the importance of work adds happiness. Work is also highly appreciated, but there are more happy people among those who do not appreciate work that highly. Safety matters the most when looking for a job, and there are more happy people among those who have selected the importance of work as the first choice when looking for a job, than among those to whom an income is the most important aspect. People are more likely happy when the quality of work is high, that is when their job consists of creative and cognitive tasks and when they have a feeling of independence.

Russian metals for arctic offshore structures

With an increasingly growing demand for natural resources, the Arctic region has become an attractive area, holding about 15% of world oil. Ice shrinkage caused by global warming encourages the development of offshore and ship-building sectors. Russia, as one of the leading oil and gas production countries is participating actively in cold resistant materials research, since half of its territory belongs to the Arctic environment, which held considerable stores of oil. Nowadays most Russian offshore platforms are located in the Sakhalin Island area, which geographically does not belong to the Arctic, but has com-parable environmental conditions. Russia recently has manufactured several offshore platforms. It became clear that further development of the Arctic off-shore structures with necessary reliability is highly depending on the materials employed. This work pursues the following objectives:  to provide a comprehensive review on Russian metals used for Arctic offshore structures on the base of standards, books, journal articles and companies reports  to overview various Arctic offshore structures and its structural characteristics  briefly discuss materials testing methods for low temperatures Master`s thesis focuses on specifications and description of Russian metals which are already in use and can be used for Arctic offshore structures. Work overviews several groups of steel, such as low carbon, low alloy, chromium containing steels, stainless steels, aluminium and nanostructured steels. Materials under discussion are grouped based on the standards, for instance the work covers shipbuilding and structural steels at the different sections. This paper provides an overview of important Russian Arctic offshore projects built for use in Russia and ordered by foreign countries. Future trends in development of the Arctic materials are discussed. Based on the information provided in this Master`s thesis it is possible to learn about Russian metals used for ships and offshore platforms operated in the Arctic region. Paper can be used as the comprehensive review of current materials, such as various steels, aluminium and nanomaterials.

We do the work you enjoy the trip

kuv., 10 x 21 cm

We do the work you enjoy the trip

kuv., 10 x 21 cm

Surface transformation hardening of carbon steel with high power fiber laser

This study investigated the surface hardening of steels via experimental tests using a multi-kilowatt fiber laser as the laser source. The influence of laser power and laser power density on the hardening effect was investigated. The microhardness analysis of various laser hardened steels was done. A thermodynamic model was developed to evaluate the thermal process of the surface treatment of a wide thin steel plate with a Gaussian laser beam. The effect of laser linear oscillation hardening (LLOS) of steel was examined. An as-rolled ferritic-pearlitic steel and a tempered martensitic steel with 0.37 wt% C content were hardened under various laser power levels and laser power densities. The optimum power density that produced the maximum hardness was found to be dependent on the laser power. The effect of laser power density on the produced hardness was revealed. The surface hardness, hardened depth and required laser power density were compared between the samples. Fiber laser was briefly compared with high power diode laser in hardening medium-carbon steel. Microhardness (HV0.01) test was done on seven different laser hardened steels, including rolled steel, quenched and tempered steel, soft annealed alloyed steel and conventionally through-hardened steel consisting of different carbon and alloy contents. The surface hardness and hardened depth were compared among the samples. The effect of grain size on surface hardness of ferritic-pearlitic steel and pearlitic-cementite steel was evaluated. In-grain indentation was done to measure the hardness of pearlitic and cementite structures. The macrohardness of the base material was found to be related to the microhardness of the softer phase structure. The measured microhardness values were compared with the conventional macrohardness (HV5) results. A thermodynamic model was developed to calculate the temperature cycle, Ac1 and Ac3 boundaries, homogenization time and cooling rate. The equations were numerically solved with an error of less than 10-8. The temperature distributions for various thicknesses were compared under different laser traverse speed. The lag of the was verified by experiments done on six different steels. The calculated thermal cycle and hardened depth were compared with measured data. Correction coefficients were applied to the model for AISI 4340 steel. AISI 4340 steel was hardened by laser linear oscillation hardening (LLOS). Equations were derived to calculate the overlapped width of adjacent tracks and the number of overlapped scans in the center of the scanned track. The effect of oscillation frequency on the hardened depth was investigated by microscopic evaluation and hardness measurement. The homogeneity of hardness and hardened depth with different processing parameters were investigated. The hardness profiles were compared with the results obtained with conventional single-track hardening. LLOS was proved to be well suitable for surface hardening in a relatively large rectangular area with considerable depth of hardening. Compared with conventional single-track scanning, LLOS produced notably smaller hardened depths while at 40 and 100 Hz LLOS resulted in higher hardness within a depth of about 0.6 mm.

Kuormanohjauksen vaikutus kaksion sähkönkulutuskäyrään

Tutkimuksen tarkoituksena oli selvittää millainen kaksion sähkönkulutuskäyrä on ja mistä kuormista se koostuu. Tarkoituksena oli myös tutkia miten kuormansiirrot vaikuttavat sähkönkulutuskäyrään ja onko kuormansiirroissa säästöpotentiaalia ajatellen asiakkaan sähkökustannuksia. Säästöpotentiaalia laskettaessa oletettiin, että asiakkaalla on sähkösopimus, jonka hinta seuraa sähköpörssin (Nord Pool) spot-hintoja. Tutkimustuloksista nähdään, että asunnon pohjakuorma aiheutuu kylmälaitteista ja suuret sähkön kulutuspiikit aiheutuvat liedestä, astianpesukoneesta ja pyykinpesukoneesta. Kuormansiirtojen vaikutus normaaliin sähkönkulutus käyrään on se, että suurten kuormien aiheuttamat kulutuspiikit siirtyivät myöhemmäksi iltaan. Laskelmissa selvisi, että kuormansiirto ei tuo asiakkaalle merkittäviä säästöjä, koska säästöjen saanti edellyttäisi pidempiä mittausjaksoja sekä päivittäisiä suuria hinnanvaihteluita sähkön spot-hinnoissa. Tutkittiin myös millaisia kylmälaitteiden kulutuskäyrät ovat ja miten pysäytykset ja uudelleenkäynnistyksen vaikuttavat niihin.

Enhancing the development of military capabilities by a systems approach

The political environment of security and defence has changed radically in the Western industrialised world since the Cold War. As a response to these changes, since the beginning of the twenty-first century, most Western countries have adopted a ‘capabilities-based approach’ to developing and operating their armed forces. More responsive and versatile military capabilities must be developed to meet the contemporary challenges. The systems approach is seen as a beneficial means of overcoming traps in resolving complex real -world issues by conventional thinking. The main objectives of this dissertation are to explore and assess the means to enhance the development of military capabilities both in concept development and experimentation (CD&E) and in national defence materiel collaboration issues. This research provides a unique perspective, a systems approach, to the development areas of concern in resolving complex real-world issues. This dissertation seeks to increase the understanding of the military capability concept both as a whole and with in its life cycle. The dissertation follows the generic functionalist systems methodology by Jackson. The methodology applies a comprehensive set of constitutive rules to examine the research objectives. This dissertation makes contribution to current studies about military capability. It presents two interdepen dent conceptual capability models: the comprehensive capability meta-model (CCMM) and the holistic capability life cycle model (HCLCM). These models holistically and systematically complement the existing, but still evolving, understanding of military capability and its life cycle. In addition, this dissertation contributes to the scientific discussion of defence procurement in its broad meaning by introducing the holistic model about the national defence materiel collaboration between the defence forces, defence industry and academia. The model connects the key collaborative mechanisms, which currently work in isolation from each other, and take into consideration the unique needs of each partner. This dissertation contributes empirical evidence regarding the benefits of enterprise architectures (EA) to CD&E. The EA approach may add value to traditional concept development by increasing the clarity, consistency and completeness of the concept. The most important use considered for EA in CD&E is that it enables further utilisation of the concept created in the case project.

Adult education policy in the European Union during the Lisbon decade : the shift to vocational adult learning and work skills matching

This doctoral dissertation investigates the adult education policy of the European Union (EU) in the framework of the Lisbon agenda 2000–2010, with a particular focus on the changes of policy orientation that occurred during this reference decade. The year 2006 can be considered, in fact, a turning point for the EU policy-making in the adult learning sector: a radical shift from a wide--ranging and comprehensive conception of educating adults towards a vocationally oriented understanding of this field and policy area has been observed, in particular in the second half of the so--called ‘Lisbon decade’. In this light, one of the principal objectives of the mainstream policy set by the Lisbon Strategy, that of fostering all forms of participation of adults in lifelong learning paths, appears to have muted its political background and vision in a very short period of time, reflecting an underlying polarisation and progressive transformation of European policy orientations. Hence, by means of content analysis and process tracing, it is shown that the new target of the EU adult education policy, in this framework, has shifted from citizens to workers, and the competence development model, borrowed from the corporate sector, has been established as the reference for the new policy road maps. This study draws on the theory of governance architectures and applies a post-ontological perspective to discuss whether the above trends are intrinsically due to the nature of the Lisbon Strategy, which encompasses education policies, and to what extent supranational actors and phenomena such as globalisation influence the European governance and decision--making. Moreover, it is shown that the way in which the EU is shaping the upgrading of skills and competences of adult learners is modeled around the needs of the ‘knowledge economy’, thus according a great deal of importance to the ‘new skills for new jobs’ and perhaps not enough to life skills in its broader sense which include, for example, social and civic competences: these are actually often promoted but rarely implemented in depth in the EU policy documents. In this framework, it is conveyed how different EU policy areas are intertwined and interrelated with global phenomena, and it is emphasised how far the building of the EU education systems should play a crucial role in the formation of critical thinking, civic competences and skills for a sustainable democratic citizenship, from which a truly cohesive and inclusive society fundamentally depend, and a model of environmental and cosmopolitan adult education is proposed in order to address the challenges of the new millennium. In conclusion, an appraisal of the EU’s public policy, along with some personal thoughts on how progress might be pursued and actualised, is outlined.

Application of the finite element method in cold forging processes

The demand for more efficient manufacturing processes has been increasing in the last few years. The cold forging process is presented as a possible solution, because it allows the production of parts with a good surface finish and with good mechanical properties. Nevertheless, the cold forming sequence design is very empirical and it is based on the designer experience. The computational modeling of each forming process stage by the finite element method can make the sequence design faster and more efficient, decreasing the use of conventional "trial and error" methods. In this study, the application of a commercial general finite element software - ANSYS - has been applied to model a forming operation. Models have been developed to simulate the ring compression test and to simulate a basic forming operation (upsetting) that is applied in most of the cold forging parts sequences. The simulated upsetting operation is one stage of the automotive starter parts manufacturing process. Experiments have been done to obtain the stress-strain material curve, the material flow during the simulated stage, and the required forming force. These experiments provided results used as numerical model input data and as validation of model results. The comparison between experiments and numerical results confirms the developed methodology potential on die filling prediction.

An experimental investigation of the effects of nozzle ellipticity on the flow structure of co-flow jet diffusion flames

The flow structure of cold and ignited jets issuing into a co-flowing air stream was experimentally studied using a laser Doppler velocimeter. Methane was employed as the jet fluid discharging from circular and elliptic nozzles with aspect ratios varying from 1.29 to 1.60. The diameter of the circular nozzle was 4.6 mm and the elliptic nozzles had approximately the same exit area as that of the circular nozzle. These non-circular nozzles were employed in order to increase the stability of attached jet diffusion flames. The time-averaged velocity and r.m.s. value of the velocity fluctuation in the streamwise and transverse directions were measured over the range of co-flowing stream velocities corresponding to different modes of flame blowout that are identified as either lifted or attached flames. On the basis of these measurements, attempts were made to explain the existence of an apparent optimum aspect ratio for the blowout of attached flames observed at higher values of co-flowing stream velocities. The insensitivity of the blowout limits of lifted flames to nozzle geometry observed in our previous work at low co-flowing stream velocities was also explained. Measurements of the fuel concentration at the jet centerline indicated that the mixing process was enhanced with the 1.38 aspect ratio jet compared with the 1.60 aspect ratio jet. On the basis of the obtained experimental data, it was suggested that the higher blowout limits of attached flames for an elliptic jet of 1.38 aspect ratio was due to higher entrainment rates.

Mikrohuokoisen pinnoitteen kehittäminen suodatinkankaan päälle

Mikrohuokoisia membraaneja käytetään monissa suodatussovelluksissa kuten vedenpuhdistuksessa. Tämän työn tavoite oli pinnoittaa suodatinkankaita mikrohuokoisella membraanilla. Membraanimateriaalin ja suodatuskankaan yhdistelmällä tavoiteltiin komposiittimateriaalia, jolla on membraanin selektiivinen erotuskyky ja kankaan mekaaniset ominaisuudet. Tämän työn kirjallisuusosa käsittelee membraanin valmistusta faasi-inversiomenetelmällä, pinnoitteeksi soveltuvia membraanimateriaaleja sekä pinnoitteen lujittamista. Kokeellisessa osassa suodatuskankaalle kehitettiin sopivaa pinnoitusmenetelmää. Pinnoitemateriaaleina käytettiin akryylidispersioainetta, polyamidia ja polysulfonia. Tuloksista huomattiin, ettei akryylidispersioaine soveltunut pinnoitemateriaaliksi. Kangasta onnistuttiin pinnoittamaan polyamidilla ja pinnoitusolosuhteita kontrolloimalla saatiin aikaiseksi pinnoite, joka pysyi kankaassa kiinni ja jonka rakenne koostui noin 12 μm huokosista. Polymeeriliuoksen pitoisuuden huomattiin vaikuttavan pinnoitteen rakenteeseen, mutta siihen jäi edelleen suuria avoimia huokosia. Suuret yksittäiset huokoset laskivat kuplapistepainetta ja tekivät huokoskokojakaumasta leveämmän. Polyamidipitoisuudella 14 ja 16 m–% pinnoite oli tunkeutunut kankaan sisään ja sen rakenne oli huokoinen, mutta pintakerrokseen muodostunut tiivis ihokerros tukki materiaalia. Tulosten perusteella kankaiden pinnoittaminen membraanikerroksella on mahdollista mutta pinnoitusprosessia täytyy edelleen kehittää, jotta päästään pienempään huokoskokoon ja kapeampaan huokoskokojakaumaan pinnoitteessa.