Gel electrolytes based on lithium macro-anion salt

Montmorillonites are composed of aluminosilicate layers stacked one above the other, and the layer thickness is approximately 1 nm. In this work lithium modified montmorillonite (Li-MMT) was prepared and used as a lithium macro-anion salt in gel electrolytes. It was found that Li-MMT exhibited good compatibility with poly(ethylene glycol), DMSO and the ionic liquid, 1-ethyl-3-methylimidazolium dicyanamide (EMIdca), and a few of novel gel electrolytes based on Li-MMT were obtained. These gel electrolytes were investigated by X-ray powder diffraction, solid state NMR, conductivity measurements and cyclic voltammetry. High conductivities up to 10^{− 4} to 10^{− 3} S/cm at room temperature were observed with these macro-anion gel electrolytes. These gel materials were promising to be used as lithium conductive electrolytes in electrochemical devices, such as lithium batteries.

Ionic liquid electrolyte porphyrin dye sensitised solar cells

Ionic liquid electrolytes based on a number of imidazolium, quaternary ammonium and phosphonium cations have been developed for porphyrin dye sensitised solar cells yielding efficiencies of up to 5.2% at 0.68 Sun.

Proton transport in choline dihydrogen phosphate/H3PO4 mixtures

Mixtures of the plastic crystal material choline dihydrogen phosphate [Choline][DHP] and phosphoric acid, from 4.5 mol% to 18 mol% H₃PO₄, were investigated and shown to have significantly higher proton conductivity compared to the pure [Choline][DHP]. This was particularly evident from the electrochemical hydrogen reduction reaction and the proton NMR diffusion measurements, in addition to ionic conductivity measured from the impedance spectroscopy. The ionic conductivity was observed to increase by more than an order of magnitude in phase I (i.e. the highest temperature solid phase in [Choline][DHP]) reaching up to 10⁻² S cm⁻¹. The multinuclear NMR spectroscopy data suggest that, at least on the timescale of the NMR measurement, the H⁺ cations and [DHP] anions are equivalent in both phases. The pulsed field gradient NMR diffusion measurements of the 18 mol% acid sample indicate that all three ions are mobile, however the H⁺ diffusion coefficient is an order of magnitude higher than for the [Choline] cation or the [DHP] anion, and therefore conduction in these materials is dominated by proton conductivity. The thermal stability, as measured by TGA, is unaffected with increasing acid additions and remains high; i.e. no significant mass loss below 200 °C.

Extraction of copper(II) ions from aqueous solutions with a methimazole-based ionic liquid

The recently synthesized ionic liquid (IL) 2-butylthiolonium bis(trifluoromethanesulfonyl)amide, [mimSBu][NTf2], has been used for the extraction of copper(II) from aqueous solution. The pH of the aqueous phase decreases upon addition of [mimSBu]+, which is attributed to partial release of the hydrogen attached to the N(3) nitrogen atom of the imidazolium ring. The presence of sparingly soluble water in [mimSBu][NTf2] also is required in solvent extraction studies to promote the incorporation of Cu(II) into the [mimSBu][NTf2] ionic liquid phase. The labile copper(II) system formed by interacting with both the water and the IL cation component has been characterized by cyclic voltammetry as well as UV−vis, Raman, and 1H, 13C, and 15N NMR spectroscopies. The extraction process does not require the addition of a complexing agent or pH control of the aqueous phase. [mimSBu][NTf2] can be recovered from the labile copper−water−IL interacting system by washing with a strong acid. High selectivity of copper(II) extraction is achieved relative to that of other divalent cobalt(II), iron(II), and nickel(II) transition-metal cations. The course of microextraction of Cu2+ from aqueous media into the [mimSBu][NTf2] IL phase was monitored in situ by cyclic voltammetry using a well-defined process in which specific interaction with copper is believed to switch from the ionic liquid cation component, [mimSBu], to the [NTf2] anion during the course of electrochemical reduction from Cu(II) to Cu(I). The microextraction−voltammetry technique provides a fast and convenient method to determine whether an IL is able to extract electroactive metal ions from an aqueous solution.

Physical and electrochemical properties of thioether-functionalized ionic liquids

The preparation and characterization of a series of ionic liquids based on S-alkyl thiolonium, S-alkyl thiotetrazolium, or S-alkyl thiobenzolium cations coupled with bis(trifluoromethanesulfonyl)amide, trifluoromethanesulfonate, alkyl phosphate, chloride, and hexafluorophosphate anions are reported. All are liquid at room temperature, except the chloride salt, which has a melting point of 92 °C. The electrochemical characteristics of this class of ionic liquid have been determined by cyclic voltammetry. Potential windows of the ionic liquids have been obtained at glassy carbon, platinum, and gold electrodes and found to be the largest at glassy carbon, but are limited by oxidation of the thioether-functionalized cation. The voltammetry of IUPAC reference potential scale systems, ferrocene/ferrocenium, cobaltocenium/cobaltocene, and decamethylferrocene/decamethylferrocenium have been evaluated, with the last being most widely applicable. Nonadditivity of Faradaic current is found in the voltammograms of decamethylferrocene in the presence of ferrocene and cobaltocenium. Diffusion coefficient, viscosity, ionic conductivity, double layer capacitance, and other physical properties have also been measured. The dependence of the diffusion coefficient vs viscosity follows the Stokes−Einstein relationship. The properties of the ionic liquids are compared with the related imidazolium family of ionic liquids.

Electrochemistry of room temperature protic ionic liquids

Eighteen protic ionic liquids containing different combinations of cations and anions, hydrophobicity, viscosity, and conductivity have been synthesized and their physicochemical properties determined. In one series, the diethanolammonium cations were combined with acetate, formate, hydrogen sulfate, chloride, sulfamate, and mesylate anions. In the second series, acetate and formate anions were combined with amine bases, triethylamine, diethylamine, triethanolamine, di-n-propylamine, and di-n-butylamine. The electrochemical characteristics of the eight protic ionic liquids that are liquid at room temperature (RTPILs) have been determined using cyclic, microelectrode, and rotating disk electrode voltammetries. Potential windows of the RTPILs have been compared at glassy carbon, platinum, gold, and boron-doped diamond electrodes and generally found to be the largest in the case of glassy carbon. The voltammetry of IUPAC recommended potential scale reference systems, ferrocene/ferrocenium and cobaltocenium/cobaltocene, have been evaluated and found to be ideal in the case of the less viscous RTPILs but involve adsorption in the highly viscous ones. Other properties such as diffusion coefficients, ionic conductivity, and double layer capacitance also have been measured. The influence of water on the potential windows, viscosity, and diffusion has been studied systematically by deliberate addition of water to the dried ionic liquids. The survey highlights the problems with voltammetric studies in highly viscous room temperature protic ionic liquids and also suggests the way forward with respect to their possible industrial use.

Effect of natural organic compounds on the removal of organic carbon in coagulation and flocculation processes

Natural organic matter (NOM) in water contains organic compounds that are both hydrophobic and hydrophilic with a wide range of molecular weights. It is composed of non-homogeneous organic compounds such as humic substances, amino acids, sugars, aliphatic and aromatic acids, and other chemical synthetic organic matters. NOM in water is a major concern not only because of its contribution to the formation of disinfection by-products (DBPs) and taste and odor, but also its influence on the demand for coagulants and disinfectants, the removal efficiency of water treatment processes, etc. This research aims at identifying the influence of NOM in coagulation and flocculation processes in order to optimize the coagulation and flocculation conditions. In this study, pretreated pond water was used as the source water. It was observed from the experimental results that: (1) The optimum pH for coagulation to remove NOM is around 7. (2) The optimum alum dose at this pH can vary from 125-1,225 mgl-1 when the TOC is increased from 4 to 25 mgl-1. (3) The presence of secondary compounds such as Ca2+, Mg2+ divalent cations had no significant effect on the removal of organic matter. (4) The presence of clay increased the organic removal by 15%. (5) The organic compound with higher molecular weight has higher removal affinity in coagulation process. (6) Floc size and settling velocity of floc and sludge production all increased with the increase in NOM concentration. From the results of Capillary Suction Time (CST) tests, the floc formed with lower TOC readily released the water to make the dewatering process easier. (7) The organic removal efficiency was significantly different for natural water containing non-homogeneous organic compounds compared to the synthetic water containing humic acid only (homogeneous organic matter). For example, the NOM removal efficiency was 80% for the synthetic water containing humic acid with TOC of 7 mgl-1 at pH 7; but the NOM removal for the pretreated pond water was 60%.

Evidence of changes in membrane pore characteristics due to filtration of dye bath liquors

This study was carried out to investigate the treatment of various salt solutions and synthetic dye bath liquors by nanofiltration using Nanomax-50 membrane in a stirred cell with 150 mL working volume. Donnan exclusion was compared by filtering salts with monovalent and divalent cations and anions. This was done by comparing three salts including sodium chloride (NaCl), calcium chloride (CaCl2) and sodium sulphate (Na2SO4). The rejection order determined was Na2SO4>NaCl>CaCl2 which is typical of a negatively charged membrane where Donnan and steric exclusion play an important role in separation. Studies on the flux and rejection characteristics of sodium sulphate were undertaken for concentrations ranging from 10 to 40 gl−1 thereby replicating actual dye bath salt concentrations. Synthetic dye bath liquors were prepared using acidic dye (Acid Green 25) at a fixed concentration of 100 mgl−1 with 10 and 15 gl−1 of sodium sulphate solutions. While, the results showed evidence of flux decline due to increased resistance and decreased transmembrane pressure, pore enlargement occurred after the filtration experiments with sodium sulphate solutions greater than 20 gl−1. Pore enlargement was even more prominent in the two synthetic dye bath liquors filtered. Pore enlargement was determined by observing the pure water flux before and after filtering sodium sulphate solutions or dye bath liquors. An increase in pore diameter of 58 and 94 %was estimated when dye bath liquors containing 10 and 15 gl−1 of sodium sulphate, respectively were filtered through the membrane. The following equation was derived in estimating the pore enlargement, where de1 and de2 are the apparent diameter of membrane pore sizes before and after filtration of salt solutions or dye bath liquors and Rm1 and Rm2 are the membrane resistance of pure water flux before and after filtration of salt solutions or dye bath liquors. These results have important implications for the application of nanofiltration technology to textile wastewater treatment and reuse.

Double layer structure of ionic liquids at the Au(111) electrode interface : an atomic force microscopy investigation

The double layer structure of two ionic liquids (ILs), 1-butyl-1- methylpyrrolidinium tris(pentafluoroethyl)trifluorophosphate ([Py ₁,₄]FAP) and 1-ethyl-3-methylimidazolium tris(pentafluoroethyl) trifluorophosphate ([EMIm]FAP) at the polarized Au(111) electrode interface is probed using Atomic Force Microscopy force measurements. The force-separation profiles suggest a multilayered morphology is present at the electrified Au(111)-IL interface, with more near surface layers detected at higher potentials. At the (slightly negative) open circuit potential, multiple ion layers are present, and the innermost layer, in contact with the Au(111) surface, is enriched in the cation due to electrostatic adsorption. Upon applying negative electrode potentials (-1.0 V, -2.0 V), stronger IL near surface structure is detected: both the number of ion layers and the force required to rupture these layers increases. Positive electrode potentials (+1.0 V, +2.0 V) also enhance IL near surface structure, but not as much as negative potentials, because surface-adsorbed anions are less effective at templating structure in subsequent layers than cations. This interfacial structure is not consistent with a double layer in the Stern-Gouy-Chapman sense, as there is no diffuse layer. The structure is consistent with a capicitative double-layer model, with a very small separation distance between the planes of charge.

Novel halogen-free chelated orthoborate-phosphonium ionic liquids : synthesis and tribophysical properties

We report on the synthesis, characterisation, and physical and tribological properties of halogen-free ionic liquids based on various chelated orthoborate anions with different phosphonium cations, both without halogen atoms in their structure. Important physical properties of the ILs including glass transition temperatures, density, viscosity and ionic conductivity were measured and are reported here. All of these new halogen-free orthoborate ionic liquids (hf-BILs) are hydrophobic and hydrolytically stable liquids at room temperature. As lubricants, these hf-BILs exhibit considerably better antiwear and friction reducing properties under boundary lubrication conditions for steel–aluminium contacts as compared with fully formulated (15W-50 grade) engine oil. Being halogen free these hf-BILs offer a more environmentally benign alternative to ILs being currently developed for lubricant applications.

Physiological metal uptake by Nostoc punctiforme

Trace metals are required for many cellular processes. The acquisition of trace elements from the environment includes a rapid adsorption of metals to the cell surface, followed by a slower internalization. We investigated the uptake of the trace elements Co²⁺, Cu²⁺, Mn²⁺, Ni²⁺, and Zn²⁺ and the non-essential divalent cation Cd²⁺ in the cyanobacterium Nostoc punctiforme. For each metal, a dose response study based on cell viability showed that the highest non-toxic concentrations were: 0.5 μM Cd²⁺, 2 μM Co²⁺, 0.5 μM Cu²⁺, 500 μM Mn²⁺, 1 μM Ni²⁺, and 18 μM Zn²⁺. Cells exposed to these non-toxic concentrations with combinations of Zn²⁺ and Cd²⁺, Zn²⁺ and Co²⁺, Zn²⁺ and Cu²⁺ or Zn²⁺ and Ni²⁺, had reduced growth in comparison to controls. Cells exposed to metal combinations with the addition of 500 μM Mn²⁺ showed similar growth compared to the untreated controls. Metal levels were measured after one and 72 h for whole cells and absorbed (EDTA-resistant) fractions and used to calculate differential uptake rates for each metal. The differences in binding and internalisation between different metals indicate different uptake processes exist for each metal. For each metal, competitive uptake experiments using ⁶⁵Zn showed that after 72 h of exposure Zn²⁺ uptake was reduced by most metals particularly 0.5 μM Cd²⁺, while 2 μM Co²⁺ increased Zn²⁺ uptake. This study demonstrates that N. punctiforme discriminates between different metals and favourably substitutes their uptake to avoid the toxic effects of particular metals.

Spectroscopic characterization of alkali-metal exchanged natrolites

Synchrotron infrared (IR) and micro-Raman spectroscopic studies have been performed on zeolite natrolites as a function of the non-framework composition at ambient conditions. This establishes the spectroscopic characterization of the ion-exchanged natrolites in the alkali-metal series both in the as-prepared hydrated (M-NAT-hyd, M = Li, Na, K, Rb, and Cs) and some stable dehydrated forms (M-NAT-deh, M = Rb and Cs). The former series exhibits non-framework cation-size dependent opening of the helical channels to span ca. 21° range in terms of the chain rotation angle, ? (or ca. 45° range in terms of the chain bridging angle, T-O2-T). For these hydrated phases, both IR and Raman spectra reveal that the degree of the red-shifts in the frequencies of the helical 8-ring channel as well as the 4-ring unit is proportional to the ionic radius of the non-framework cations. Linear fits to the data show negative slopes of -55.7 from Raman and -18.3 from IR in the 8-ring frequencies and ionic radius relationship. The spectroscopic data are also used to identify the modes of the dehydration-induced "collapse" of the helical 8-ring channels as observed in the stable anhydrous Rb-NAT-deh and Cs-NAT-deh. In addition, we demonstrate that the spectroscopic data in the hydrated series can be used to distinguish different water arrangements along the helical channels based on the frequency shifts in the H-O-H bending band and the changes in the O-H stretching vibration modes.

In-situ dehydration studies of fully K-, Rb-, and Cs-exchanged natrolites

In-situ synchrotron X-ray powder diffraction studies of K-, Rb-, and Cs-exchanged natrolites between room temperature and 425 °C revealed that the dehydrated phases with collapsed frameworks start to form at 175, 150, and 100 °C, respectively. The degree of the framework collapse indicated by the unit-cell volume contraction depends on the size of the non-framework cation: K-exchanged natrolite undergoes an 18.8% unit-cell volume contraction when dehydrated at 175 °C, whereas Rb- and Cs-exchanged natrolites show unit-cell volume contractions of 18.5 and 15.2% at 150 and 100 °C, respectively. In the hydrated phases, the dehydration-induced unit-cell volume reduction diminishes as the cation size increases and reveals increasingly a negative slope as smaller cations are substituted into the pores of the natrolite structure. The thermal expansion of the unit-cell volumes of the dehydrated K-, Rb-, and Cs-phases have positive thermal expansion coefficients of 8.80 × 10⁻⁵ K⁻¹, 1.03 × 10⁻⁴ K⁻¹, and 5.06 × 10⁻⁵ K⁻¹, respectively. Rietveld structure refinements of the dehydrated phases at 400 °C reveal that the framework collapses are due to an increase of the chain rotation angles, ψ, which narrow the channels to a more elliptical shape. Compared to their respective hydrated structures at ambient conditions, the dehydrated K-exchanged natrolite at 400 °C shows a 2.2-fold increase in ψ, whereas the dehydrated Rb- and Cs-natrolites at 400 °C reveal increases of ψ by ca. 3.7 and 7.3 times, respectively. The elliptical channel openings of the dehydrated K-, Rb-, to Cs-phases become larger as the cation size increases. The disordered non-framework cations in the hydrated K-, Rb-, and Cs-natrolite order during dehydration and the subsequent framework collapse. The dehydrated phases of Rb- and Cs-natrolite can be stabilized at ambient conditions.

Halogen-free chelated orthoborate ionic liquids and organic ionic plastic crystals

Five halogen-free orthoborate salts comprised of three different cations (cholinium, pyrrolidinium and imidazolium) and two orthoborate anions, bis(mandelato)borate and bis(salicylato)borate, were synthesised and characterised by DSC, X-ray diffraction and NMR. DSC measurements revealed that glass transition points of these orthoborate salts are in the temperature range from −18 to −2 °C. In addition, it was found that [EMPy][BScB] and [EMIm][BScB] salts have solid–solid phase transitions below their melting points, i.e. they exhibit typical features of plastic crystals. Salts of the bis(salicylato)borate anion [BScB]− have higher melting points compared with corresponding salts of the bis(mandelato)borate anion [BMB]−. Single crystal X-ray diffraction crystallography (for [Chol][BScB] crystals) and solid-state multinuclear (13C, 11B and 15N) NMR spectroscopy were employed for the structural characterisation of [Chol][BScB], [EMPy][BScB] and [EMIm][BScB], which are solids at room temperature: a strong interaction between [BScB]− anions and [Chol]+ cations was identified as (i) hydrogen bonding between OH of [Chol]+ and carbonyl groups of [BScB]− and (ii) as the inductive C–Hπ interaction. In the other salt, [EMIm][BScB], anions exhibit ππ stacking in combination with C–Hπ interactions with [EMIm]+ cations. These interactions were not identified in [EMPy][BScB] probably because of the lack of aromaticity in cations of the latter system. Our data on the formation of a lanthanum complex with bis(salicylato)borate in the liquid mixture of La3+(aq) with [Chol][BScB] suggest that this class of novel ILs can be potentially used in the extraction processes of metal ions of rare earth elements.

Oxygen reduction reaction activity of La-based perovskite oxides in alkaline medium : a thin-film rotating ring-disk electrode study

In this work, LaMO₃ and LaNi_0.5M_0.5O₃ (M = Ni, Co, Fe, Mn and Cr) perovskite oxide electrocatalysts were synthesized by a combined ethylenediaminetetraacetic acid-citrate complexation technique and subsequent calcinations at 1000 °C in air. Their powder X-ray diffraction patterns demonstrate the formation of a specific crystalline structure for each composition. The catalytic property of these materials toward the oxygen reduction reaction (ORR) was studied in alkaline potassium hydroxide solution using the rotating disk and rotating ring-disk electrode techniques. Carbon is considered to be a crucial additive component because its addition into perovskite oxide leads to optimized ORR current density. For LaMO₃ (M = Ni, Co, Fe, Mn and Cr)), in terms of the ORR current densities, the performance is enhanced in the order of LaCrO₃, LaFeO₃, LaNiO₃, LaMnO₃, and LaCoO3. For LaNi_0.5M_0.5O₃, the ORR current performance is enhanced in the order of LaNi_0.5Fe_0.5O₃, LaNi_0.5Co_0.5O₃, LaNi_0.5Cr_0.5O₃, and LaNi_0.5Mn_0.5O₃. Overall, LaCoO₃ demonstrates the best performance. Most notably, substituting half of the nickel with cobalt, iron, manganese, or chromium translates the ORR to a more positive onset potential, suggesting the beneficial catalytic effect of two transition metal cations with Mn as the most promising candidate. Koutecky–Levich analysis on the ORR current densities of all compositions indicates that the four-electron pathway is favored on these oxides, which are consistent with hydroperoxide ion formation of <2%.