Geosynthetic Reinforced Soil for Low-Volume Bridge Abutments, January 2012

This report presents a review of literature on geosynthetic reinforced soil (GRS) bridge abutments, and test results and analysis from two field demonstration projects (Bridge 1 and Bridge 2) conducted in Buchanan County, Iowa, to evaluate the feasibility and cost effectiveness of the use of GRS bridge abutments on low-volume roads (LVRs). The two projects included GRS abutment substructures and railroad flat car (RRFC) bridge superstructures. The construction costs varied from $43k to $49k, which was about 50 to 60% lower than the expected costs for building a conventional bridge. Settlement monitoring at both bridges indicated maximum settlements ≤1 in. and differential settlements ≤ 0.2 in transversely at each abutment, during the monitoring phase. Laboratory testing on GRS fill material, field testing, and in ground instrumentation, abutment settlement monitoring, and bridge live load (LL) testing were conducted on Bridge 2. Laboratory test results indicated that shear strength parameters and permanent deformation behavior of granular fill material improved when reinforced with geosynthetic, due to lateral restraint effect at the soilgeosynthetic interface. Bridge LL testing under static loads indicated maximum deflections close to 0.9 in and non-uniform deflections transversely across the bridge due to poor load transfer between RRFCs. The ratio of horizontal to vertical stresses in the GRS fill was low (< 0.25), indicating low lateral stress on the soil surrounding GRS fill material. Bearing capacity analysis at Bridge 2 indicated lower than recommended factor of safety (FS) values due to low ultimate reinforcement strength of the geosynthetic material used in this study and a relatively weak underlying foundation layer. Global stability analysis of the GRS abutment structure revealed a lower FS than recommended against sliding failure along the interface of the GRS fill material and the underlying weak foundation layer. Design and construction recommendations to help improve the stability and performance of the GRS abutment structures on future projects, and recommendations for future research are provided in this report.

Safer Constrauction and Maintenance Practices to Minimize Potential Liabiliy by Counties from Accidents, Septemeber 1979

Tort claims resulting from alleged highway defects have introduced an additional element in the planning, design, construction, and maintenance of highways. A survey of county governments in Iowa was undertaken in order to quantify the magnitude and determine the nature of this problem. This survey included the use of mailed questionnaires and personal interviews with County Engineers. Highway-related claims filed against counties in Iowa amounted to about $52,000,000 during the period 1973 through 1978. Over $30,000,000 in claims was pending at the end of 1978. Settlements of judgments were made at a cost of 12.2% of the amount claimed for those claims that had been disposed of, not including costs for handling claims, attorney fees, or court costs. There was no clear time trend in the amount of claims for the six-year period surveyed, although the anount claimed in 1978 was about double the average for the preceding five years. Problems that resulted in claims for damages from counties have generally related to alleged omissions in the use of traffic control devices or defects, often temporary, resulting from alleged inadequacies in highway maintenance. The absence of stop signs or warning signs often has been the central issue in a highway-related tort claim. Maintenance problems most frequently alleged have included inadequate shoulders, surface roughness, ice o? snow conditions, and loose gravel. The variation in the occurrence of tort claims among 85 counties in Iowa could not be related to any of the explanatory variables that were tested. Claims hppeared to have occurred randomly. However, using data from a subsample of 11 counties, a significant relationship was shown probably to exist between the amount of tort claims and the extensiveness of use of wcirning signs on the respective county road systems. Although there was no indication in any county that their use of warning signs did not conform with provisions of the Manual on Uniform Traffic Control Devices (Federal Highway Administration, Government Printing Office, Washington, D.C., 1978), many more warning signs were used in some counties than would be required to satisfy this minimum requirement. Sign vandalism reportedly is a problem in all counties. The threat of vandalism and the added costs incurred thereby have tended to inhibit more extensive use of traffic control devices. It also should be noted that there is no indication from this research of a correlation between the intensiveness of sign usage and highway safety. All highway maintenance activities introduce some extraordinary hazard for motorists. Generally effective methodologies have evolved for use on county road systems for routine maintenance activities, procedures that tend to reduce the hazard to practical and reasonably acceptable levels. Blading of loose-surfaced roads is an examples such a routine maintenance activity. Alternative patterns for blading that were investigated as part of this research offered no improvements in safety when compared with the method in current use and introduced a significant additional cost that was unacceptable, given the existing limitations in resources available for county roads.

RECOVERY OF AN OXISOL DEGRADED BY THE CONSTRUCTION OF A HYDROELECTRIC POWER PLANT

ABSTRACT The removal of thick layers of soil under native scrubland (Cerrado) on the right bank of the Paraná River in Selvíria (State of Mato Grosso do Sul, Brazil) for construction of the Ilha Solteira Hydroelectric Power Plant caused environmental damage, affecting the revegetation process of the stripped soil. Over the years, various kinds of land use and management systems have been tried, and the aim of this study was to assess the effects of these attempts to restore the structural quality of the soil. The experiment was conducted considering five treatments and thirty replications. The following treatments were applied: stripped soil without anthropic intervention and total absence of plant cover; stripped soil treated with sewage sludge and planted to eucalyptus and grass a year ago; stripped soil developing natural secondary vegetation (capoeira) since 1969; pastureland since 1978, replacing the native vegetation; and soil under native vegetation (Cerrado). In the 0.00-0.20 m layer, the soil was chemically characterized for each experimental treatment. A 30-point sampling grid was used to assess soil porosity and bulk density, and to assess aggregate stability in terms of mean weight diameter (MWD) and geometric mean diameter (GMD). Aggregate stability was also determined using simulated rainfall. The results show that using sewage sludge incorporated with a rotary hoe improved the chemical fertility of the soil and produced more uniform soil pore size distribution. Leaving the land to develop secondary vegetation or turning it over to pastureland produced an intermediate level of structural soil quality, and these two treatments produced similar results. Stripped soil without anthropic intervention was of the lowest quality, with the lowest values for cation exchange capacity (CEC) and macroporosity, as well as the highest values of soil bulk density and percentage of aggregates with diameter size <0.50 mm, corroborated by its lower organic matter content. However, the percentage of larger aggregates was higher in the native vegetation treatment, which boosted MWD and GMD values. Therefore, assessment of some land use and management systems show that even decades after their implementation to mitigate the degenerative effects resulting from the installation of the Hydroelectric Plant, more efficient approaches are still required to recover the structural quality of the soil.

Signing on Very Low Volume Rurd Roads Iowa DOT Project HR-262, July, 1984

Research was undertaken to define an appropriate level of use of traffic control devices on rural secondary roads that carry very low traffic volumes. The goal of this research was to improve the safety and efficiency of travel on the rural secondary road system. This goal was to be accomplished by providing County Engineers with guidance concerning the cost-effective use of traffic control devices on very low volume rural roads. A further objective was to define the range of traffic volumes on the roads for which the recommendations would be appropriate. Little previous research has been directed toward roads that carry very low traffic volumes. Consequently, the factual input for this research was developed by conducting an inventory of the signs and markings actually in use on 2,069 miles of rural road in Iowa. Most of these roads carried 15 or fewer vehicles per day. Additional input was provided by a survey of the opinions of County Engineers and Supervisors in Iowa. Data from both the inventory and the opinion survey indicated a considerable lack of uniformity in the application of signs on very low volume rural roads. The number of warning signs installed varied from 0.24 per mile to 3.85 per mile in the 21 counties in which the inventory was carried out. The use of specific signs not only varied quite widely among counties but also indicated a lack of uniform application within counties. County officials generally favored varying the elaborateness of signing depending upon the type of surface and the volume of traffic on different roads. Less elaborate signing would be installed on an unpaved road than on a paved road. A concensus opinion was that roads carrying fewer than 25 vehicles per day should have fewer signs than roads carrying higher volumes. Although roads carrying 0 to 24 vehicles per day constituted over 24% of the total rural secondary system, they carried less than 3% of the total travel on that system. Virtually all of these roads are classified as area service roads and would thus be expected to carry only short trips primarily by local motorists. Consequently, it was concluded that the need for warning signs rarely can be demonstrated on unpaved rural roads with traffic volumes of fewer than 25 vehicles per day. It is recommended that each county designate a portion of its roads as an Area Service Level B system. All road segments with very low traffic volumes should be considered for inclusion in this system. Roads included in this system may receive a lesser level of maintenance and a reduced level of signing. The county is also afforded protection from liability arising from accidents occurring on roads designated as part of an Area Service Level B system. A uniform absence of warning signs on roads of this nature is not expected to have any discernible effect on the safety or quality of service on these very low volume roads. The resources conserved may be expended more effectively to upgrade maintenance and traffic control on roads carrying higher volumes where the beneficial effect on highway safety and service will be much more consequential.

Evaluation of 1977 Asphalt Concrete Sprinkle Treatments, December 1980

Iowa's first sprinkle treatment in 1974 was applied to a short section of old US 30 west of Ames. A roll type seal coat spreader was used to apply several types of sprinkle aggregates. The following year a spinner type tailgate spreader was used for sprinkle application of an Iowa 7 project in Webster County. Uniform spreading and tire marks were problems in these early projects. A special spinner spreader was built in 1976 and mounted on a truck specially equipped with smooth tires. This special unit was tested in early 1977 on a project that had been scheduled for 1976. Spinner type spreaders proved unacceptable due to non-uniformity of spreading.

Iowa Traffic Control Devices and Pavement Markings: A Manual for Cities and Counties April 2001

Iowa Traffic Control Devices and Pavement Markings: A Manual for Cities and Counties has been developed to provide state and local transportation agencies with suggestions and examples related to traffic control devices and pavement markings. Both rural and urban applications are included. The primary source of information for this document is the Manual on Uniform Traffic Control Devices (MUTCD), but many additional references have also been used. A complete listing of these is included in the appendix to this manual, and the reader is invited to consult these references for more in-depth information. The contents of this manual are not intended to represent standard practice or to imply legal requirements for installation in any particular manner. This document should be used as a supplement to the MUTCD, not as a substitute for any requirements contained therein. Engineering judgement should be applied to all decisions regarding traffic control devices and pavement markings. All references to the MUTCD in this manual apply to the millennium edition. The reader should be aware that many millennium revisions are allowed phase-in periods by the Federal Highway Administration (FHWA), ranging from two to ten years. These extended compliance periods should be considered when making decisions regarding traffic control devices and pavement markings. A new addition to the MUTCD, Part 5, “Traffic Control Devices for Low-Volume Roads,” also contains valuable recommendations for signing and marking low volume roads. This manual is presented in an easy to use threering format. Topics included in the complete guide manual may not apply to all jurisdictions and can easily be removed or modified as desired. Desired millennium MUTCD sections may be added for quick reference using the divider at the end of this document. Contents may also be available on CD-ROM in the future.

Roadway Design Standards for Rural and Suburban Subdivisions Final Report, June 2007

In Iowa, there are currently no uniform design standards for rural and suburban subdivision development roadways. Without uniform design standards, many counties are unable to provide adequate guidance for public facilities, particularly roadways, to be constructed as part of a rural subdivision development. If a developer is not required to install appropriate public improvements or does not do so properly, significant liability and maintenance expenses can be expected, along with the potential for major project costs to correct the situation. Not having uniform design standards for rural and suburban subdivision development improvements in Iowa creates situations where there is potential for inconsistency and confusion. Differences in the way development standards are applied also create incentives or disincentives for developers to initiate subdivision platting in a particular county. With the wide range of standards or lack of standards for local roads in development areas, it is critical that some level of uniformity is created to address equity in development across jurisdictional lines. The standards must be effective in addressing the problem, but they must not be so excessive as to curtail development activities within a local jurisdiction. In order to address the concerns, cities and counties have to work together to identify where growth is going to be focused. Within that long-term growth area, the roadways should be constructed to urban standards to provide an easier transition to traditional urban facilities as the area is developed. Developments outside of the designated growth area should utilize a rural cross section since it is less likely to have concentrated urban development. The developers should be required to develop roadways that are designed for a minimum life of 40 years, and the county should accept dedication of the roadway and be responsible for its maintenance.

Medication use in pregnancy: a cross-sectional, multinational web-based study.

OBJECTIVES: Intercountry comparability between studies on medication use in pregnancy is difficult due to dissimilarities in study design and methodology. This study aimed to examine patterns and factors associated with medications use in pregnancy from a multinational perspective, with emphasis on type of medication utilised and indication for use. DESIGN: Cross-sectional, web-based study performed within the period from 1 October 2011 to 29 February 2012. Uniform collection of drug utilisation data was performed via an anonymous online questionnaire. SETTING: Multinational study in Europe (Western, Northern and Eastern), North and South America and Australia. PARTICIPANTS: Pregnant women and new mothers with children less than 1 year of age. PRIMARY AND SECONDARY OUTCOME MEASURES: Prevalence of and factors associated with medication use for acute/short-term illnesses, chronic/long-term disorders and over-the-counter (OTC) medication use. RESULTS: The study population included 9459 women, of which 81.2% reported use of at least one medication (prescribed or OTC) during pregnancy. Overall, OTC medication use occurred in 66.9% of the pregnancies, whereas 68.4% and 17% of women reported use of at least one medication for treatment of acute/short-term illnesses and chronic/long-term disorders, respectively. The extent of self-reported medicated illnesses and types of medication used by indication varied across regions, especially in relation to urinary tract infections, depression or OTC nasal sprays. Women with higher age or lower educational level, housewives or women with an unplanned pregnancy were those most often reporting use of medication for chronic/long-term disorders. Immigrant women in Western (adjusted OR (aOR): 0.55, 95% CI 0.34 to 0.87) and Northern Europe (aOR: 0.50, 95% CI 0.31 to 0.83) were less likely to report use of medication for chronic/long-term disorders during pregnancy than non-immigrants. CONCLUSIONS: In this study, the majority of women in Europe, North America, South America and Australia used at least one medication during pregnancy. There was a substantial inter-region variability in the types of medication used.

Whole-rat protein content estimation: applicability of the Nx6.25 factor

The amino acid composition of the protein from three strains of rat (Wistar, Zucker lean and Zucker obese), subjected to reference and high-fat diets has been used to determine the mean empirical formula, molecular weight and N content of whole-rat protein. The combined whole protein of the rat was uniform for the six experimental groups, containing an estimate of 17.3% N and a mean aminoacyl residue molecular weight of 103.7. This suggests that the appropriate protein factor for the calculation of rat protein from its N content should be 5.77 instead of the classical 6.25. In addition, an estimate of the size of the non-protein N mass in the whole rat gave a figure in the range of 5.5 % of all N. The combination of the two calculations gives a protein factor of 5.5 for the conversion of total N into rat protein.

Different modulation of adipocytokine expression in four main white adipose tissue sites in the rat: mesenteric, perigonadal, retroperitoneal and subcutaneous

White adipose tissue (WAT) is a disperse organ acting as energy storage depot and endocrine/paracrine controlling factor in the management of energy availability and inflammation. WAT sites response under energy-related stress is not uniform. In the present study we have analyzed how different WAT sites respond to limited food restriction as a way to better understand the role of WAT in the pathogenesis of the metabolic syndrome.

Post-Plutonic Magmatism: from the Source to the Emplacement of an Upper Crustal Dyke Swarm, Adamello Massif, Italy

Magmas of the arc-tholeiitic and calc-alkaline differentiation suites contribute substantially to the formation of continental crust in subduction zones. Different geochemical-petrological models have been put forward to achieve evolved magmas forming large volumes of tonalitic to granitic plutons, building an important part of the continental crust. Primary magmas produced in the mantle wedge overlying the subducted slab migrate through the mantle and the crust. During the transfer, magma can accumulate in intermediate reservoirs at different levels where crystallization leads to differentiation and the heat transfer from the magma, together with gained heat from solidification, lead to partial melting of the crust. Partial melts can be assimilated and mix with more primitive magma. Moreover, already formed crystal cumulates or crystal mushes can be recycled and reactivated to transfer to higher crustal levels. Magma transport in the crust involves fow through fractures within a brittle elastic rock. The solidified magma filled crack, a dyke, can crosscut previously formed geological structures and thus serves as a relative or absolute time marker. The study area is situated in the Adamello massif. The Adamello massif is a composite of plutons that were emplaced between 42 and 29 million years. A later dyke swarm intruded into the southern part of the Adamello Batholith. A fractionation model covering dyke compositions from picrobasalts to dacites results in the cummulative crystallization of 17% olivine, 2% Cr-rich spinel, 18% clinopyroxene, 41% amphibole, 4% plagioclase and 0.1% magnetite to achieve an andesitic composition out of a hydrous primitive picrobasalt. These rocks show a similar geochemical evolution as experimental data simulating fractional crystallization and associated magma differentiation at lower crustal depth (7-10 kbar). The peraluminous, corundum normative composition is one characteristic of more evolved dacitic magmas, which has been explained in a long lasting debate with two di_erent models. Melting of mafic crust or politic material provides one model, whereas an alternative is fractionation from primary mantle derived melts. Amphibole occurring in basaltic-andesitic and andesitic dyke rocks as fractionating cumulate phase extracted from lower crustal depth (6-7.5 kbar) is driving the magmas to peraluminous, corundum normative compositions, which are represented by tonalites forming most of the Adamello Batholith. Most primitive picrobasaltic dykes have a slightly steepened chondrite normalized rare earth elements (REE) pattern and the increased enrichment of light-REE (LREE) for andesites and dacites can be explained by the fractional crystallization model originating from a picrobasalt, taking the changing fractionating phase assemblage and temperature into account. The injection of hot basaltic magma (~1050°C) in a closely spaced dyke swarm increases the surface of the contact to the mainly tonalitic wallrock. Such a setting induces partial melting of the wall rock and selective assimilation. Partial melting of the tonalite host is further expressed through intrusion breccias from basaltic dykes. Heat conduction models with instantaneous magma injection for such a dyke swarm geometry can explain features of partial melting observed in the field. Geochemical data of minerals and bulk rock further underline the selective or bulk assimilation of the tonalite host rock at upper crustal levels (~2-3 kbar), in particular with regard to light ion lithophile elements (LILE) such as Sr, Ba and Rb. Primitive picrobasalts carry an immiscible felsic assimilant as enclaves that bring along refractory rutile and zircon with textures typically found in oceanic plagiogranites or high pressure/low-temperature metamorphic rocks in general. U-Pb data implies a lower Cretaceous age for zircon not yet described as assimilant in Eocene to Oligocene magmatic rocks of the Central Southern Alps. The distribution of post-plutonic dykes in large batholiths such as the Adamello is one of the key features for understanding the regional stress field during the post-batholith emplacement cooling history. The emplacement of the regional dyke swarm covering the southern part of the Adamello massif was associated with consistent left lateral strike-slip movement along magma dilatation planes, leading to en echelon segmentation of dykes. Through the dilation by magma of pre-existing weaknesses and cracks in an otherwise uniform host rock, the dyke propagation and according orientation in the horizontal plane adjusted continuously perpendicular to least compressive remote stress σ3, resulting in an inferred rotation of the remote principal stress field. Les magmas issus des zones de subduction contribuent substantiellement à la formation de la croûte continentale. Les plutons tonalitiques et granitiques représentent, en effet, une partie importante de la croûte continentale. Des magmas primaires produits dans le 'mantle wedge ', partie du manteau se trouvant au-dessus de la plaque plongeante dans des zones de subduction, migrent à travers le manteau puis la croûte. Pendant ce transfert, le magma peut s'accumuler dans des réservoirs intermédiaires à différentes profondeurs. Le stockage de magma dans ces réservoirs engendre, d'une part, la différentiation des magmas par cristallisation fractionnée et, d'autre part, une fusion partielle la croûte continentale préexistante associée au transfert de la chaleur des magmas vers l'encaissant. Ces liquides magmatiques issus de la croûte peuvent, ensuite, se mélanger avec des magmas primaires. Le transport du magma dans la croûte implique notamment un flux de magma à travers différentes fractures recoupant les roches encaissantes élastiques. Au cours de ce processus de migration, des cumulats de cristaux ou des agrégats de cristaux encore non-solidifiés, peuvent être recyclés et réactivés pour être transportés à des niveaux supérieures de la croûte. Le terrain d'étude est situé dans le massif d'Adamello. Celui-ci est composé de plusieurs plutons mis en place entre 42 et 29 millions d'années. Dans une phase tardive de l'activité magmatique liée à ce batholite, une série de filons de composition variable allant de picrobasalte à des compositions dacitiques s'est mise en place la partie sud du massif. Deux modèles sont proposés dans la littérature, pour expliquer la formation des magmas dacitiques caractérisés par des compositions peralumineux (i.e. à corindon normatif). Le premier modèle propose que ces magmas soient issus de la fusion de matériel mafique et pélitique présent dans la partie inférieur de la croûte, alors que le deuxième modèle suggère une évolution par cristallisation fractionnée à partir de liquides primaires issus du manteau. Un modèle de cristallisation fractionnée a pu être développé pour expliquer l'évolution des filons de l'Adamello. Ce modèle explique la formation des filons dacitiques par la cristallisation fractionnée de 17% olivine, 2% spinelle riche en Cr, 18% clinopyroxène, 41% amphibole, 4% plagioclase et 0.1% magnetite à partir de liquide de compositions picrobasaltiques. Ce modèle prend en considération les contraintes pétrologiques déduites de l'observation des différents filons ainsi que du champ de stabilité des différentes phases en fonction de la température. Ces roches montrent une évolution géochimique similaire aux données expérimentales simulant la cristallisation fractionnée de magmas évoluant à des niveaux inférieurs de la croûte (7-10 kbar). Le modèle montre, en particulier, le rôle prépondérant de l'amphibole, une phase qui contrôle en particulier le caractère peralumineux des magmas différentiés ainsi que leurs compositions en éléments en traces. Des phénomènes de fusion partielle de l'encaissant tonalitique lors de la mise en place de _lons mafiques sont observée sur le terrain. L'injection du magma basaltique chaud (~1050°C) sous forme de filons rapprochés augmente la surface du contact avec l'encaissante tonalitique. Une telle situation produit la fusion partielle des roches encaissantes nécessaire à l'incorporation d'enclaves mafiques observés au sein des tonalites. Pour comprendre les conditions nécessaires pour la fusion partielle des roches encaissantes, des modèles de conduction thermique pour une injection simultanée d'une série de filons ont été développées. Des données géochimiques sur les minéraux et sur les roches totales soulignent qu'au niveau supérieur de la croûte, l'assimilation sélective ou totale de l'encaissante tonalitique modifie la composition du liquide primaire pour les éléments lithophiles tel que le Sr, Ba et Rb. Un autre aspect important concernant la pétrologie des filons de l'Adamello est la présence d'enclaves felsiques dans les filons les plus primitifs. Ces enclaves montrent, en particulier, des textures proches de celles rencontrées dans des plagiogranites océaniques ou dans des roches métamorphiques de haute pression/basse température. Ces enclaves contiennent du zircon et du rutile. La datations de ces zircons à l'aide du géochronomètre U-Pb indique un âge Crétacé inférieur. Cet âge est important, car aucune roche de cet âge n'a été considérée comme un assimilant potentiel pour des roches magmatiques d'âge Eocène à Oligocène dans les Alpes Sud Centrales. La réparation spatiale des filons post-plutoniques dans des grands batholites tel que l'Adamello, est une caractéristique clé pour la compréhension des champs de contraintes lors du refroidissement du batholite. L'orientation des filons va, en particulier, indiqué la contrainte minimal au sein des roches encaissante. La mise en place de la série de filon recoupant la partie Sud du massif de l'Adamello est associée à un décrochement senestre, un décrochement que l'on peut lié aux contraintes tectoniques régionales auxquelles s'ajoutent l'effet de la dilatation produite par la mise en place du batholite lui-même. Ce décrochement senestre produit une segmentation en échelon des filons.

Noise-induced Brownian motion of spiral waves

We study the erratic displacement of spiral waves forced to move in a medium with random spatiotemporal excitability. Analytical work and numerical simulations are performed in relation to a kinematic scheme, assumed to describe the autowave dynamics for weakly excitable systems. Under such an approach, the Brownian character of this motion is proved and the corresponding dispersion coefficient is evaluated. This quantity shows a nontrivial dependence on the temporal and spatial correlation parameters of the external fluctuations. In particular, a resonantlike behavior is neatly evidenced in terms of the noise correlation time for the particular situation of spatially uniform fluctuations. Actually, this case turns out to be, to a large extent, exactly solvable, whereas a pair of dispersion mechanisms are discussed qualitatively and quantitatively to explain the results for the more general scenario of spatiotemporal disorder.

Feedback control of unstable cellular solidification fronts

We present a feedback control scheme to stabilize unstable cellular patterns during the directional solidification of a binary alloy. The scheme is based on local heating of cell tips which protrude ahead of the mean position of all tips in the array. The feasibility of this scheme is demonstrated using phase-field simulations and, experimentally, using a real-time image processing algorithm, to track cell tips, coupled with a movable laser spot array device to heat the tips locally. We demonstrate, both numerically and experimentally, that spacings well below the threshold for a period-doubling instability can be stabilized. As predicted by the numerical calculations, cellular arrays become stable with uniform spacing through the feedback control which is maintained with minimal heating.

Periodic forcing of scroll rings and control of Winfree turbulence in excitable media

By simulations of the Barkley model, action of uniform periodic nonresonant forcing on scroll rings and wave turbulence in three-dimensional excitable media is investigated. Sufficiently strong rapid forcing converts expanding scroll rings into the collapsing ones and suppresses the Winfree turbulence caused by the negative tension of wave filaments. Slow strong forcing has an opposite effect, leading to expansion of scroll rings and induction of the turbulence. These effects are explained in the framework of the phenomenological kinematic theory of scroll waves.

Spontaneous mirror symmetry breaking in the limited enantioselective autocatalysis model: abyssal hydrotermal vents as scenario for the emergence of chirality in prebiotic chemistry

The emergence of chirality in enantioselective autocatalysis for compounds unable to transform according to the Frank-like reaction network is discussed with respect to the controversial limited enantioselectivity (LES) model composed of coupled enantioselective and non-enantioselective autocatalyses. The LES model cannot lead to spontaneous mirror symmetry breaking (SMSB) either in closed systems with a homogeneous temperature distribution or in closed systems with a stationary non-uniform temperature distribution. However, simulations of chemical kinetics in a two-compartment model demonstrate that SMSB may occur if both autocatalytic reactions are spatially separated at different temperatures in different compartments but coupled under the action of a continuous internal flow. In such conditions, the system can evolve, for certain reaction and system parameters, toward a chiral stationary state; that is, the system is able to reach a bifurcation point leading to SMSB. Numerical simulations in which reasonable chemical parameters have been used suggest that an ade- quate scenario for such a SMSB would be that of abyssal hydrothermal vents, by virtue of the typical temper- ature gradients found there and the role of inorganic solids mediating chemical reactions in an enzyme-like role. Key Words: Homochirality Prebiotic chemistry.