(Table 1) Results from XRD analysis as well as sediment type and selected results from ring shear experiments

The location of the seaward tip of a subduction thrust controls material transfer at convergent plate margins, and hence global mass balances. At approximately half of those margins, the material of the subducting plate is completely underthrust so that no accretion or even subduction erosion takes place. Along the remaining margins, material is scraped off the subducting plate and added to the upper plate by frontal accretion. We here examine the physical properties of subducting sediments off Costa Rica and Nankai, type examples for an erosional and an accretionary margin, to investigate which parameters control the level where the frontal thrust cuts into the incoming sediment pile. A series of rotary-shear experiments to measure the frictional strength of the various lithologies entering the two subduction zones were carried out. Results include the following findings: (1) At Costa Rica, clay-rich strata at the top of the incoming succession have the lowest strength (µres = 0.19) while underlying calcareous ooze, chalk and diatomite are strong (up to µres = 0.43; µpeak = 0.56). Hence the entire sediment package is underthrust. (2) Off Japan, clay-rich deposits within the lower Shikoku Basin inventory are weakest (µres = 0.13-0.19) and favour the frontal proto-thrust to migrate into one particular horizon between sandy, competent turbidites below and ash-bearing mud above. (3) Taking in situ data and earlier geotechnical testing into account, it is suggested that mineralogical composition rather than pore-pressure defines the position of the frontal thrust, which locates in the weakest, clay mineral-rich (up to 85 wt.%) materials. (4) Smectite, the dominant clay mineral phase at either margin, shows rate strengthening and stable sliding in the frontal 50 km of the subduction thrust (0.0001-0.1 mm/s, 0.5-25 MPa effective normal stress). (5) Progressive illitization of smectite cannot explain seismogenesis, because illite-rich samples also show velocity strengthening at the conditions tested.

(Table 1) Age determination of sediment core SO139-74KL

A multiproxy record has been acquired from a piston core (SO139-74KL) taken offshore southern Sumatra, an area which is situated in the southwestern sector of the tropical Indo-Pacific Warm Pool. The high-resolution data sets (X-ray fluorescence, total organic carbon, and C37 alkenones) were used to track changes in paleoproductivity, freshwater budget, and sea surface temperature (SST) of the tropical climate system at orbital time scales over the past 300 ka. Our paleoclimatic data show that enhanced marine paleoproductivity was directly related to strengthening of coastal upwelling during periods of increased boreal summer insolation and associated SE monsoon strength with a precessional cyclicity. Changes in freshwater supply were primarily forced by precession-controlled changes in boreal NW winter monsoon rainfall enclosing an additional sea level component. SST variations of 2°-5°C occurred at eccentricity and precessional cyclicity. We suggest that the sea surface temperature variability off southern Sumatra is predominantly related to three major causes: (1) variations in upwelling intensity; (2) an elevated freshwater input into the southern Makassar Strait leading to reduced supply of warmer surface waters from the western Pacific and increased subsurface water transport via the Indonesian Throughflow into the Indian Ocean; and (3) long-term changes in the intensity or frequency of low-latitude climate phenomena, such as El Niño-Southern Oscillation.

Calibration of three year old child dummies (phase II). Final report.

Mode of access: Internet.

Implementation cost to consumers of Part 581 - Bumper Standard, Phase II; weight and cost study of three "X" body bumper systems; and consumer replacement cost for complete bumper systems studied. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Program Trixy : multi-group analysis of nuclear reactors in three space dimensions : for the IBM type 704 computer /

"Physics and Math. TID-4500 (15th Ed.)"--Title page.

Operator's and organizational maintenance manual : water purification unit, van-type, body mounted, electric driven, AC, 115, 208 V, single- and 3-phase, 60 hertz, 1/20 to 2 hp, 3000 gph (MET-PRO model 3000V), NSN 4610-00-168-1799.

"18 June 1980."

Operator's manual : grinding kit, valve seat, electric 35 degree angle type concentric drive, 1/4 horsepower, AC/DC, single phase, 115-volt, 14000 RPM rated no load speed (K.O. Lee Company model P300BB) (4910-060-9983) and (K.O. Lee Company model P300BB-M2) (4910-473-6437).

"February 1965."

Operator and organizational maintenance manual (including repair parts and special tool lists) : tester, engine distributor, bench type, 6, 12, and 24-volt distributors, single-phase, 60-cycle, 115-volt (Heyer Products Company Inc., model 168) (4910-392-2939).

"30 September 1963."

Operator's, manual : milling machine, ram type, swivel head, plain table, power feed, 1 1/2 horsepower, 110-volt, 60-cycle, single-phase (Van Norman Machine Company models IR-3-22 and IRQ-3-22) (3417-624-4254).

"March 1967."

Organizational maintenance manual : lathe, engine, bench mounted, solid bed type, 10 inch swing, no. 2 Morse taper center, 1-3/8 spindle hole, 110-volts, 60 cycle, single phase 3/4-horsepower, w/Army dwg. no. 7550151 bench (standard-modern tool series 2,000 model, 11 inch) (3416-517-0955).

"November 1965."

Operator, organizational, direct support, and general support maintenance manual for air conditioner, vertical compact : type I, vertical, size C, 18,000 BTU/hr, class I, 208 volt, 3 phase, 50/60 hertz, Keco model F18T-2 : NSN 4120-00-168-1781.

"21 December 1979."

Operator and organizational maintenance manual : water purification unit, van-type body mounted; electric driven, AC, 115, 208V single-and 3-phase, 60 hertz ... NS 4610-01-016-9964.

"5 March 1979."

Organizational maintenance repair parts and special tools lists : water purification unit, van-type, body mounted, electric driven, AC, 115/208 V, single and 3 phase, 60 hertz, 1/20 to 2 hp, 1500 GPH, model EMC-1500S, NSN 4610-01-037-8746.

"15 May 1980."

Direct support and general support maintenance manual : water purification unit, van type, body mounted, electric motor driven, AC, DC, 115, 208 V, single and 3 phase, 60 hertz, 1/20 to 2 hp, 1500 gph, model EMC-1500S, NSN 4610-01-037-8746, EMC Industries Inc., DAAKO1-76-C-5661.

"1 August 1979."