5.5W CWYb3+ : Y2O3 ceramic laser pumped with 970 nm laser diode

CW laser output has been demonstrated for polycrystalline transparent 10 at.% Yb3+-doped Y2O3 ceramics. End-pumped with 970 nm laser diode, a maximum output power of 5.5 W has been obtained with absorbed pump power of 31.1 W. The slope efficiency is 25% while the threshold pump power is 5.6 W. Saturation is not observed in our experiments, indicating higher laser output can be expected with higher pump power. (C) 2004 Elsevier B.V. All rights reserved.

High-energy LDA switched side-pumped electro-optical Q-switched Nd : YAG ceramic laser

By employing a uniformly compact side-pumping system, a high-energy electro-optical Q-switched Nd:YAG ceramic laser has been demonstrated. With 420 W quasi-cw laser-diode-array pumping at 808 ran and a 100 Hz modulating repetition rate, 50 mJ output energy at 1064 nm was obtained with 10 ns pulse width, 5 W average output power, and 5 MW peak power. Its corresponding slope efficiency was 29.8%. The laser system operated quite stably and no saturation phenomena have been observed, which means higher output energy could be expected. Laser parameters between ceramic and single-crystal Nd:YAG lasers have been compared, and pulse characteristics of Nd:YAG ceramic with different repetition rate have been investigated in detail. The still-evolving Nd:YAG ceramics are potential super excellent media for high-energy laser applications. (C) 2007 Optical Society of America.

Comparison of Yb-doped fiber laser with one-end and double-end pumping configuration

A high-power Ytterbium-doped fiber laser (YDFL) with homemade double clad fiber (DCF) is introduced in this paper. The output power characteristics of a linear cavity fiber laser have been studied theoretically by solving the rate equations and experimentally tested with single- and double-end-pumping configurations. When both ends of the fiber are pumped by two high-power laser diodes with a launched power of similar to 300 W each, a maximum CW output of 444 W is obtained with a slope efficiency of similar to 75%. (c) 2006 Elsevier Ltd. All rights reserved.

高效率,窄脉冲1198.5nm Ba(NO_3)_2喇曼激光器(英文)

利用1 064 nm的Nd∶YAG激光抽运振荡腔内的硝酸钡晶体,获得高效率、窄脉冲的喇曼激光输出.硝酸钡晶体由水溶液降温法生长,长度为48 mm.喇曼振荡腔由对抽运光、一阶、二阶斯托克斯光有不同反射率的双色平面镜构成.当抽运光功率达到4.5 W时,获得最高的一阶斯托克斯喇曼激光功率为1.48 W,相应的转换效率为32.9%,并测得斜率效率为40%.由于受激喇曼散射的作用,喇曼脉冲光由抽运脉冲光的19.8 ns压缩为2.4 ns,获得的喇曼激光脉冲波形具有的＂上升沿陡峭、下降沿缓慢＂的特性,对其形成过程作了

Interações sobre a pluviosidade em encostas de clima tropical úmido e os movimentos de massa: o caso de sub-bacias do Alto Rio São João - RJ

Cada vez são mais comuns problemas relacionados a movimentos de massa nas encostas de clima tropical no Estado do Rio de Janeiro, especialmente na Serra do Mar, provocados por acumulados pluviométricos intensos. A ocupação humana desordenada de áreas sensíveis a tais processos geomorfológicos, bem como as condicionantes geológicas, geomorfológicas, pedológicas e de uso e cobertura do solo são apontadas como fatores cruciais na explicação desses processos. O maior conhecimento da dinâmica pluviométrica bem como suas interações com tais aspectos físicos ligados ao relevo parece ser a chave dessa maior compreensão desses fenômenos. Assim foram realizadas pesquisas relacionadas aos volumes e intensidades das chuvas na região do Alto Curso do Rio São João, bem como uma análise dos movimentos de massa identificados através de imagens de satélite e in loco, como forma de fornecer subsídios à melhor gestão do espaço dessas regiões montanhosa estão vulneráveis a movimentos de massa. A correlação entre os acumulados e a intensidade pluviométrica com fenômenos climáticos de escala global, como El Niño e La Niña também foi contemplada nessa pesquisa, mostrando uma relação mais alta com relação à intensidade da chuva mensal para anos de El Niño e para anos de La Niña uma reduzida ocorrência dessas intensidades pluviométricas. Os estudos revelaram que os tipos de solos e sua cobertura e uso têm uma grande influência na deflagração de movimentos de massa. Foram observados um número reduzido de movimentos de massa em áreas naturais e uma maior proporção desses movimentos em áreas utilizadas para a atividade da pecuária na região. Grande parte dos movimentos de massa ocorreram em áreas de Cambissolos (áreas mais elevadas) e Latossolos (áreas de encostas em menores altitudes). Ambos os solos são mais espessos do que os encontrados em áreas mais declivosas, apresentando maior acúmulo de materiais a serem mobilizados durante grandes acumulados pluviométricos, gerando movimentos de massa. A análise mostrou também que áreas mais chuvosas e com maior ocorrência de acumulados pluviométricos extremos, acima de 100 mm/dia e acima de 30mm/mês concentraram um número maior de movimentos de massa, como a região mais próxima da estação de Quartéis (porção leste). Por outro lado áreas bastante elevadas, com altas declividades, porém com predomínio de Mata Atlântica e áreas com solos menos espessos, como os Neossolos Litólicos, se mostraram com um número reduzido desses processos. Enfim esse estudo mostrou a necessidade de se gerir melhor os espaços dessas áreas sensíveis sob o ponto de vista geomorfológico, até por que são áreas na periferia de regiões densamente habitadas e cujas demandas tendem a se tornar cada vez mais marcantes, o que pode gerar problemas locais, atingindo sua população e economia, com sérias conseqüências para o ambiente.

Radially polarized and pulsed output from passively Q-switched Nd:YAG ceramic microchip laser

For the first time, to the best of our knowledge, a radially polarized laser pulse was produced from a passively Q-switched Nd:YAG ceramic microchip laser with a piece of Cr4+:YAG crystal as the saturable absorber and multilayer concentric subwavelength grating as the polarization-selective output coupler. The averaged laser power reached 450 mW with a slope efficiency of 30.2%. The laser pulse had a maximum peak power of 759 W, a minimum pulse duration of 86 ns, and a 6.7 kHz repetition rate at 3.7 W absorbed pump power. The polarization degree of the radially polarized pulse was measured to be as high as 97.4%. Such a radially polarized laser pulse with a high peak power and a short width is important to numerous applications such as metal cutting. (C) 2008 Optical Society of America

High-power Nd:YAG planar waveguide laser with YAG and Al2O3 claddings

Thermal effects in Nd:YAG planar waveguide lasers with non-symmetrical claddings are discussed. The heat generated in the active core can be removed more efficiently by directly contacting the active core to the heat sink. Several cladding materials are compared to optimize the heat removal. Furthermore, uniform pumping is achieved with oblique edge-pumping technique. Using quasi-CW pumping at 1 KHz repetition rate, an average output power of 280 W with a slope efficiency of 38% is obtained with a positive unstable resonator. (C) 2008 Elsevier B.V. All rights reserved.

High power single transverse mode operation of a tapered large-mode-area fiber laser

To get high output power with good beam quality, a tapered section is introduced to large-mode-area (LMA) Yb-doped fiber laser. Output characteristics of the fiber laser without tapered section and with tapered section are compared experimentally. When the launched pump power is 119.1 W, 77.9 W with M-2 3.08 and 56.4 W with M-2 1.14 can be obtained, respectively. The corresponding slope efficiencies are 71.8% and 54.1%, respectively. Although output power of the tapered fiber laser has 30.6% penalty, brightness of it is as much as 5.28 times of the fiber laser without tapered section. Moreover, spectra of them are measured. It is found that tapered section makes lasing wavelength of the fiber laser shorter. (c) 2007 Elsevier B.V. All rights reserved.

Efficient excitations of radially and azimuthally polarized Nd 3+:YAG ceramic microchip laser by use of subwavelength multilayer concentric gratings composed of Nb2O5/SiO2

Cylindrical vector beams were produced from laser diode end-pumped Nd:YAG ceramic microchip laser by use of two types of subwavelength multilayer gratings as the axisymmetric-polarization output couplers respectively. The grating mirrors are composed of high- and low-refractive-index (Nb2O5/SiO2) layers alternately while each layer is shaped into triangle and concentric corrugations. For radially polarized laser output, the beam power reached 610mW with a polarization extinction ratio ( PER) of 61: 1 and a slope efficiency of 68.2%; for azimuthally polarized laser output, the beam power reached 626mW with a PER of 58: 1 and a slope efficiency of 47.6%. In both cases, the laser beams had near-diffraction limited quality. Small differences of beam power, PER and slope efficiency between radially and azimuthally polarized laser outputs were not critical, and could be minimized by further optimized adjustment to laser cavity and the reflectances of respective grating mirrors. The results manifested, by use of the photonic crystal gratings mirrors and end-pumped microchip laser configuration, CVBs can be generated efficiently with high modal symmetry and polarization purity. (C) 2008 Optical Society of America.

Cr^3＋，Yb^3＋，Er^3＋共掺磷酸盐铒玻璃转镜调Q激光性质研究

研究了Cr^3＋，Yb^3＋，Er^3＋共掺磷酸盐铒玻璃转镜调Q激光性质．三种Er2O3掺杂浓度的激光实验结果表明，在Er2O3名义掺杂浓度为0．5wt％时，玻璃的综合激光性质最好，重复频率为0．1Hz时，它的激光阈值功率为14．5mJ，最大输出能量为9．6mJ，斜率效率为0．55％．在同种实验条件下，比较了Cr14和Kigre公司生产的QE-7S激光性质参数，实验表明，前者激光阈值功率稍低，而后者的斜率效率和最大输出功率略高．

铬镱铒共掺磷酸盐玻璃的激光性质

研究了氙灯抽运脉宽、输出耦合镜的反射率、铒玻璃工作温度以及工作重复频率对铬镱铒共掺磷酸盐玻璃激光输出能量的影响。结果表明, 对于输出能量, 抽运脉宽为2.3 ms(10%最大幅度间)时较好; 综合考虑激光阈值和斜率效率, 输出耦合镜的反射率为85%时较好。此外, 如同大多数激光介质那样, 铬镱铒共掺磷酸盐玻璃的激光输出能量随铒玻璃工作温度的升高和工作重复频率的增加而降低。

Er3+离子浓度对Er3+/Yb3+共掺磷酸盐玻璃上转换 发光的影响

The upconversion emission of Er³⁺/Yb³⁺ codoped phosphate glass with 980 nm excitation was investigated. In the glass Er³⁺ concentration has a great influence on the intensity and the ratio of green and red light upconversion. The slope of the green luminenscence intensity as a function of pumping power ranges from 2.52 to 3.27, is the evidence of the three photon excitation process. The three photon process can also be concluded from excitation spectra when emission wavelength is 545 nm. The effect of Er³⁺ concentration is also discussed.

铒镱共掺磷酸盐玻璃的激光性质

制备了镱铒共掺的磷酸盐玻璃并研究了室温下LD泵浦的连续激光输出性质。在泵浦功率为496mW时实现了最大输出功率77mW。讨论了在不同玻璃样品厚度和谐振腔长度时的斜率效率的变化以及在不同玻璃样品厚度，泵浦功率和谐振腔长度时的不同激光模式竞争的动力学行为。结果表明：激光光谱受到光学增益和光学损耗相对大小的限制。

Upconversion emission in Er3+ doped novel bismuthate glass

Novel Er3+-doped bismuth lead strontiam glass was fabricated and characterized, and the absorption spectrum and upconversion spectrum of the glass were studied. The Judd-Ofelt intensity parameters Omega(t)(t = 2, 4, 6) were found to be Omega(2) = 3.27 x 10(-20) cm(2), Omega(4) = 1.15 x 10(-20) cm(2), and Omega(6) = 0.38 x 10(-20) cm(2). The oscillator strength, the spontaneous transition probabilities, the fluorescence branching ratios, and excited state lifetimes were also measured and calculated. The upconversion emission intensity varies with the power of infrared excitation intensity. A plot of log I-up vs log I-IR yields a straight line with slope 1.86, 1.88 and 1.85, corresponding to 525, 546, and 657 nm emission bands, respectively, which indicates that a two-photon process for the red and green emission.

室温下连续波运行Tm:YAP泵浦的Ho:YAG激光器

我们报道了一种以二极管泵浦的 1.94 μm Tm:YAP激光器为泵浦源，常温下在2.1 μm连续运行的Ho:YAG激光器。最大输出功率1.5 W，相应斜率效率为17.9%，二极管到的转换效率为5.6%。