Influence of Current Pulse Shape on Directly Modulated Systems Performance in Metro Area Optical Networks

Due to the fact that a metro network market is very cost sensitive, direct modulated schemes appear attractive. In this paper a CWDM (Coarse Wavelength Division Multiplexing) system is studied in detail by means of an Optical Communication System Design Software; a detailed study of the modulated current shape (exponential, sine and gaussian) for 2.5 Gb/s CWDM Metropolitan Area Networks is performed to evaluate its tolerance to linear impairments such as signal-to-noise-ratio degradation and dispersion. Point-to-point links are investigated and optimum design parameters are obtained. Through extensive sets of simulation results, it is shown that some of these shape pulses are more tolerant to dispersion when compared with conventional gaussian shape pulses. In order to achieve a low Bit Error Rate (BER), different types of optical transmitters are considered including strongly adiabatic and transient chirp dominated Directly Modulated Lasers (DMLs). We have used fibers with different dispersion characteristics, showing that the system performance depends, strongly, on the chosen DML?fiber couple.

OntoTag - A Linguistic and Ontological Annotation Model Suitable for the Semantic Web

OntoTag - A Linguistic and Ontological Annotation Model Suitable for the Semantic Web 1. INTRODUCTION. LINGUISTIC TOOLS AND ANNOTATIONS: THEIR LIGHTS AND SHADOWS Computational Linguistics is already a consolidated research area. It builds upon the results of other two major ones, namely Linguistics and Computer Science and Engineering, and it aims at developing computational models of human language (or natural language, as it is termed in this area). Possibly, its most well-known applications are the different tools developed so far for processing human language, such as machine translation systems and speech recognizers or dictation programs. These tools for processing human language are commonly referred to as linguistic tools. Apart from the examples mentioned above, there are also other types of linguistic tools that perhaps are not so well-known, but on which most of the other applications of Computational Linguistics are built. These other types of linguistic tools comprise POS taggers, natural language parsers and semantic taggers, amongst others. All of them can be termed linguistic annotation tools. Linguistic annotation tools are important assets. In fact, POS and semantic taggers (and, to a lesser extent, also natural language parsers) have become critical resources for the computer applications that process natural language. Hence, any computer application that has to analyse a text automatically and ‘intelligently’ will include at least a module for POS tagging. The more an application needs to ‘understand’ the meaning of the text it processes, the more linguistic tools and/or modules it will incorporate and integrate. However, linguistic annotation tools have still some limitations, which can be summarised as follows: 1. Normally, they perform annotations only at a certain linguistic level (that is, Morphology, Syntax, Semantics, etc.). 2. They usually introduce a certain rate of errors and ambiguities when tagging. This error rate ranges from 10 percent up to 50 percent of the units annotated for unrestricted, general texts. 3. Their annotations are most frequently formulated in terms of an annotation schema designed and implemented ad hoc. A priori, it seems that the interoperation and the integration of several linguistic tools into an appropriate software architecture could most likely solve the limitations stated in (1). Besides, integrating several linguistic annotation tools and making them interoperate could also minimise the limitation stated in (2). Nevertheless, in the latter case, all these tools should produce annotations for a common level, which would have to be combined in order to correct their corresponding errors and inaccuracies. Yet, the limitation stated in (3) prevents both types of integration and interoperation from being easily achieved. In addition, most high-level annotation tools rely on other lower-level annotation tools and their outputs to generate their own ones. For example, sense-tagging tools (operating at the semantic level) often use POS taggers (operating at a lower level, i.e., the morphosyntactic) to identify the grammatical category of the word or lexical unit they are annotating. Accordingly, if a faulty or inaccurate low-level annotation tool is to be used by other higher-level one in its process, the errors and inaccuracies of the former should be minimised in advance. Otherwise, these errors and inaccuracies would be transferred to (and even magnified in) the annotations of the high-level annotation tool. Therefore, it would be quite useful to find a way to (i) correct or, at least, reduce the errors and the inaccuracies of lower-level linguistic tools; (ii) unify the annotation schemas of different linguistic annotation tools or, more generally speaking, make these tools (as well as their annotations) interoperate. Clearly, solving (i) and (ii) should ease the automatic annotation of web pages by means of linguistic tools, and their transformation into Semantic Web pages (Berners-Lee, Hendler and Lassila, 2001). Yet, as stated above, (ii) is a type of interoperability problem. There again, ontologies (Gruber, 1993; Borst, 1997) have been successfully applied thus far to solve several interoperability problems. Hence, ontologies should help solve also the problems and limitations of linguistic annotation tools aforementioned. Thus, to summarise, the main aim of the present work was to combine somehow these separated approaches, mechanisms and tools for annotation from Linguistics and Ontological Engineering (and the Semantic Web) in a sort of hybrid (linguistic and ontological) annotation model, suitable for both areas. This hybrid (semantic) annotation model should (a) benefit from the advances, models, techniques, mechanisms and tools of these two areas; (b) minimise (and even solve, when possible) some of the problems found in each of them; and (c) be suitable for the Semantic Web. The concrete goals that helped attain this aim are presented in the following section. 2. GOALS OF THE PRESENT WORK As mentioned above, the main goal of this work was to specify a hybrid (that is, linguistically-motivated and ontology-based) model of annotation suitable for the Semantic Web (i.e. it had to produce a semantic annotation of web page contents). This entailed that the tags included in the annotations of the model had to (1) represent linguistic concepts (or linguistic categories, as they are termed in ISO/DCR (2008)), in order for this model to be linguistically-motivated; (2) be ontological terms (i.e., use an ontological vocabulary), in order for the model to be ontology-based; and (3) be structured (linked) as a collection of ontology-based triples, as in the usual Semantic Web languages (namely RDF(S) and OWL), in order for the model to be considered suitable for the Semantic Web. Besides, to be useful for the Semantic Web, this model should provide a way to automate the annotation of web pages. As for the present work, this requirement involved reusing the linguistic annotation tools purchased by the OEG research group (http://www.oeg-upm.net), but solving beforehand (or, at least, minimising) some of their limitations. Therefore, this model had to minimise these limitations by means of the integration of several linguistic annotation tools into a common architecture. Since this integration required the interoperation of tools and their annotations, ontologies were proposed as the main technological component to make them effectively interoperate. From the very beginning, it seemed that the formalisation of the elements and the knowledge underlying linguistic annotations within an appropriate set of ontologies would be a great step forward towards the formulation of such a model (henceforth referred to as OntoTag). Obviously, first, to combine the results of the linguistic annotation tools that operated at the same level, their annotation schemas had to be unified (or, preferably, standardised) in advance. This entailed the unification (id. standardisation) of their tags (both their representation and their meaning), and their format or syntax. Second, to merge the results of the linguistic annotation tools operating at different levels, their respective annotation schemas had to be (a) made interoperable and (b) integrated. And third, in order for the resulting annotations to suit the Semantic Web, they had to be specified by means of an ontology-based vocabulary, and structured by means of ontology-based triples, as hinted above. Therefore, a new annotation scheme had to be devised, based both on ontologies and on this type of triples, which allowed for the combination and the integration of the annotations of any set of linguistic annotation tools. This annotation scheme was considered a fundamental part of the model proposed here, and its development was, accordingly, another major objective of the present work. All these goals, aims and objectives could be re-stated more clearly as follows: Goal 1: Development of a set of ontologies for the formalisation of the linguistic knowledge relating linguistic annotation. Sub-goal 1.1: Ontological formalisation of the EAGLES (1996a; 1996b) de facto standards for morphosyntactic and syntactic annotation, in a way that helps respect the triple structure recommended for annotations in these works (which is isomorphic to the triple structures used in the context of the Semantic Web). Sub-goal 1.2: Incorporation into this preliminary ontological formalisation of other existing standards and standard proposals relating the levels mentioned above, such as those currently under development within ISO/TC 37 (the ISO Technical Committee dealing with Terminology, which deals also with linguistic resources and annotations). Sub-goal 1.3: Generalisation and extension of the recommendations in EAGLES (1996a; 1996b) and ISO/TC 37 to the semantic level, for which no ISO/TC 37 standards have been developed yet. Sub-goal 1.4: Ontological formalisation of the generalisations and/or extensions obtained in the previous sub-goal as generalisations and/or extensions of the corresponding ontology (or ontologies). Sub-goal 1.5: Ontological formalisation of the knowledge required to link, combine and unite the knowledge represented in the previously developed ontology (or ontologies). Goal 2: Development of OntoTag’s annotation scheme, a standard-based abstract scheme for the hybrid (linguistically-motivated and ontological-based) annotation of texts. Sub-goal 2.1: Development of the standard-based morphosyntactic annotation level of OntoTag’s scheme. This level should include, and possibly extend, the recommendations of EAGLES (1996a) and also the recommendations included in the ISO/MAF (2008) standard draft. Sub-goal 2.2: Development of the standard-based syntactic annotation level of the hybrid abstract scheme. This level should include, and possibly extend, the recommendations of EAGLES (1996b) and the ISO/SynAF (2010) standard draft. Sub-goal 2.3: Development of the standard-based semantic annotation level of OntoTag’s (abstract) scheme. Sub-goal 2.4: Development of the mechanisms for a convenient integration of the three annotation levels already mentioned. These mechanisms should take into account the recommendations included in the ISO/LAF (2009) standard draft. Goal 3: Design of OntoTag’s (abstract) annotation architecture, an abstract architecture for the hybrid (semantic) annotation of texts (i) that facilitates the integration and interoperation of different linguistic annotation tools, and (ii) whose results comply with OntoTag’s annotation scheme. Sub-goal 3.1: Specification of the decanting processes that allow for the classification and separation, according to their corresponding levels, of the results of the linguistic tools annotating at several different levels. Sub-goal 3.2: Specification of the standardisation processes that allow (a) complying with the standardisation requirements of OntoTag’s annotation scheme, as well as (b) combining the results of those linguistic tools that share some level of annotation. Sub-goal 3.3: Specification of the merging processes that allow for the combination of the output annotations and the interoperation of those linguistic tools that share some level of annotation. Sub-goal 3.4: Specification of the merge processes that allow for the integration of the results and the interoperation of those tools performing their annotations at different levels. Goal 4: Generation of OntoTagger’s schema, a concrete instance of OntoTag’s abstract scheme for a concrete set of linguistic annotations. These linguistic annotations result from the tools and the resources available in the research group, namely • Bitext’s DataLexica (http://www.bitext.com/EN/datalexica.asp), • LACELL’s (POS) tagger (http://www.um.es/grupos/grupo-lacell/quees.php), • Connexor’s FDG (http://www.connexor.eu/technology/machinese/glossary/fdg/), and • EuroWordNet (Vossen et al., 1998). This schema should help evaluate OntoTag’s underlying hypotheses, stated below. Consequently, it should implement, at least, those levels of the abstract scheme dealing with the annotations of the set of tools considered in this implementation. This includes the morphosyntactic, the syntactic and the semantic levels. Goal 5: Implementation of OntoTagger’s configuration, a concrete instance of OntoTag’s abstract architecture for this set of linguistic tools and annotations. This configuration (1) had to use the schema generated in the previous goal; and (2) should help support or refute the hypotheses of this work as well (see the next section). Sub-goal 5.1: Implementation of the decanting processes that facilitate the classification and separation of the results of those linguistic resources that provide annotations at several different levels (on the one hand, LACELL’s tagger operates at the morphosyntactic level and, minimally, also at the semantic level; on the other hand, FDG operates at the morphosyntactic and the syntactic levels and, minimally, at the semantic level as well). Sub-goal 5.2: Implementation of the standardisation processes that allow (i) specifying the results of those linguistic tools that share some level of annotation according to the requirements of OntoTagger’s schema, as well as (ii) combining these shared level results. In particular, all the tools selected perform morphosyntactic annotations and they had to be conveniently combined by means of these processes. Sub-goal 5.3: Implementation of the merging processes that allow for the combination (and possibly the improvement) of the annotations and the interoperation of the tools that share some level of annotation (in particular, those relating the morphosyntactic level, as in the previous sub-goal). Sub-goal 5.4: Implementation of the merging processes that allow for the integration of the different standardised and combined annotations aforementioned, relating all the levels considered. Sub-goal 5.5: Improvement of the semantic level of this configuration by adding a named entity recognition, (sub-)classification and annotation subsystem, which also uses the named entities annotated to populate a domain ontology, in order to provide a concrete application of the present work in the two areas involved (the Semantic Web and Corpus Linguistics). 3. MAIN RESULTS: ASSESSMENT OF ONTOTAG’S UNDERLYING HYPOTHESES The model developed in the present thesis tries to shed some light on (i) whether linguistic annotation tools can effectively interoperate; (ii) whether their results can be combined and integrated; and, if they can, (iii) how they can, respectively, interoperate and be combined and integrated. Accordingly, several hypotheses had to be supported (or rejected) by the development of the OntoTag model and OntoTagger (its implementation). The hypotheses underlying OntoTag are surveyed below. Only one of the hypotheses (H.6) was rejected; the other five could be confirmed. H.1 The annotations of different levels (or layers) can be integrated into a sort of overall, comprehensive, multilayer and multilevel annotation, so that their elements can complement and refer to each other. • CONFIRMED by the development of: o OntoTag’s annotation scheme, o OntoTag’s annotation architecture, o OntoTagger’s (XML, RDF, OWL) annotation schemas, o OntoTagger’s configuration. H.2 Tool-dependent annotations can be mapped onto a sort of tool-independent annotations and, thus, can be standardised. • CONFIRMED by means of the standardisation phase incorporated into OntoTag and OntoTagger for the annotations yielded by the tools. H.3 Standardisation should ease: H.3.1: The interoperation of linguistic tools. H.3.2: The comparison, combination (at the same level and layer) and integration (at different levels or layers) of annotations. • H.3 was CONFIRMED by means of the development of OntoTagger’s ontology-based configuration: o Interoperation, comparison, combination and integration of the annotations of three different linguistic tools (Connexor’s FDG, Bitext’s DataLexica and LACELL’s tagger); o Integration of EuroWordNet-based, domain-ontology-based and named entity annotations at the semantic level. o Integration of morphosyntactic, syntactic and semantic annotations. H.4 Ontologies and Semantic Web technologies (can) play a crucial role in the standardisation of linguistic annotations, by providing consensual vocabularies and standardised formats for annotation (e.g., RDF triples). • CONFIRMED by means of the development of OntoTagger’s RDF-triple-based annotation schemas. H.5 The rate of errors introduced by a linguistic tool at a given level, when annotating, can be reduced automatically by contrasting and combining its results with the ones coming from other tools, operating at the same level. However, these other tools might be built following a different technological (stochastic vs. rule-based, for example) or theoretical (dependency vs. HPS-grammar-based, for instance) approach. • CONFIRMED by the results yielded by the evaluation of OntoTagger. H.6 Each linguistic level can be managed and annotated independently. • REJECTED: OntoTagger’s experiments and the dependencies observed among the morphosyntactic annotations, and between them and the syntactic annotations. In fact, Hypothesis H.6 was already rejected when OntoTag’s ontologies were developed. We observed then that several linguistic units stand on an interface between levels, belonging thereby to both of them (such as morphosyntactic units, which belong to both the morphological level and the syntactic level). Therefore, the annotations of these levels overlap and cannot be handled independently when merged into a unique multileveled annotation. 4. OTHER MAIN RESULTS AND CONTRIBUTIONS First, interoperability is a hot topic for both the linguistic annotation community and the whole Computer Science field. The specification (and implementation) of OntoTag’s architecture for the combination and integration of linguistic (annotation) tools and annotations by means of ontologies shows a way to make these different linguistic annotation tools and annotations interoperate in practice. Second, as mentioned above, the elements involved in linguistic annotation were formalised in a set (or network) of ontologies (OntoTag’s linguistic ontologies). • On the one hand, OntoTag’s network of ontologies consists of − The Linguistic Unit Ontology (LUO), which includes a mostly hierarchical formalisation of the different types of linguistic elements (i.e., units) identifiable in a written text; − The Linguistic Attribute Ontology (LAO), which includes also a mostly hierarchical formalisation of the different types of features that characterise the linguistic units included in the LUO; − The Linguistic Value Ontology (LVO), which includes the corresponding formalisation of the different values that the attributes in the LAO can take; − The OIO (OntoTag’s Integration Ontology), which  Includes the knowledge required to link, combine and unite the knowledge represented in the LUO, the LAO and the LVO;  Can be viewed as a knowledge representation ontology that describes the most elementary vocabulary used in the area of annotation. • On the other hand, OntoTag’s ontologies incorporate the knowledge included in the different standards and recommendations for linguistic annotation released so far, such as those developed within the EAGLES and the SIMPLE European projects or by the ISO/TC 37 committee: − As far as morphosyntactic annotations are concerned, OntoTag’s ontologies formalise the terms in the EAGLES (1996a) recommendations and their corresponding terms within the ISO Morphosyntactic Annotation Framework (ISO/MAF, 2008) standard; − As for syntactic annotations, OntoTag’s ontologies incorporate the terms in the EAGLES (1996b) recommendations and their corresponding terms within the ISO Syntactic Annotation Framework (ISO/SynAF, 2010) standard draft; − Regarding semantic annotations, OntoTag’s ontologies generalise and extend the recommendations in EAGLES (1996a; 1996b) and, since no stable standards or standard drafts have been released for semantic annotation by ISO/TC 37 yet, they incorporate the terms in SIMPLE (2000) instead; − The terms coming from all these recommendations and standards were supplemented by those within the ISO Data Category Registry (ISO/DCR, 2008) and also of the ISO Linguistic Annotation Framework (ISO/LAF, 2009) standard draft when developing OntoTag’s ontologies. Third, we showed that the combination of the results of tools annotating at the same level can yield better results (both in precision and in recall) than each tool separately. In particular, 1. OntoTagger clearly outperformed two of the tools integrated into its configuration, namely DataLexica and FDG in all the combination sub-phases in which they overlapped (i.e. POS tagging, lemma annotation and morphological feature annotation). As far as the remaining tool is concerned, i.e. LACELL’s tagger, it was also outperformed by OntoTagger in POS tagging and lemma annotation, and it did not behave better than OntoTagger in the morphological feature annotation layer. 2. As an immediate result, this implies that a) This type of combination architecture configurations can be applied in order to improve significantly the accuracy of linguistic annotations; and b) Concerning the morphosyntactic level, this could be regarded as a way of constructing more robust and more accurate POS tagging systems. Fourth, Semantic Web annotations are usually performed by humans or else by machine learning systems. Both of them leave much to be desired: the former, with respect to their annotation rate; the latter, with respect to their (average) precision and recall. In this work, we showed how linguistic tools can be wrapped in order to annotate automatically Semantic Web pages using ontologies. This entails their fast, robust and accurate semantic annotation. As a way of example, as mentioned in Sub-goal 5.5, we developed a particular OntoTagger module for the recognition, classification and labelling of named entities, according to the MUC and ACE tagsets (Chinchor, 1997; Doddington et al., 2004). These tagsets were further specified by means of a domain ontology, namely the Cinema Named Entities Ontology (CNEO). This module was applied to the automatic annotation of ten different web pages containing cinema reviews (that is, around 5000 words). In addition, the named entities annotated with this module were also labelled as instances (or individuals) of the classes included in the CNEO and, then, were used to populate this domain ontology. • The statistical results obtained from the evaluation of this particular module of OntoTagger can be summarised as follows. On the one hand, as far as recall (R) is concerned, (R.1) the lowest value was 76,40% (for file 7); (R.2) the highest value was 97, 50% (for file 3); and (R.3) the average value was 88,73%. On the other hand, as far as the precision rate (P) is concerned, (P.1) its minimum was 93,75% (for file 4); (R.2) its maximum was 100% (for files 1, 5, 7, 8, 9, and 10); and (R.3) its average value was 98,99%. • These results, which apply to the tasks of named entity annotation and ontology population, are extraordinary good for both of them. They can be explained on the basis of the high accuracy of the annotations provided by OntoTagger at the lower levels (mainly at the morphosyntactic level). However, they should be conveniently qualified, since they might be too domain- and/or language-dependent. It should be further experimented how our approach works in a different domain or a different language, such as French, English, or German. • In any case, the results of this application of Human Language Technologies to Ontology Population (and, accordingly, to Ontological Engineering) seem very promising and encouraging in order for these two areas to collaborate and complement each other in the area of semantic annotation. Fifth, as shown in the State of the Art of this work, there are different approaches and models for the semantic annotation of texts, but all of them focus on a particular view of the semantic level. Clearly, all these approaches and models should be integrated in order to bear a coherent and joint semantic annotation level. OntoTag shows how (i) these semantic annotation layers could be integrated together; and (ii) they could be integrated with the annotations associated to other annotation levels. Sixth, we identified some recommendations, best practices and lessons learned for annotation standardisation, interoperation and merge. They show how standardisation (via ontologies, in this case) enables the combination, integration and interoperation of different linguistic tools and their annotations into a multilayered (or multileveled) linguistic annotation, which is one of the hot topics in the area of Linguistic Annotation. And last but not least, OntoTag’s annotation scheme and OntoTagger’s annotation schemas show a way to formalise and annotate coherently and uniformly the different units and features associated to the different levels and layers of linguistic annotation. This is a great scientific step ahead towards the global standardisation of this area, which is the aim of ISO/TC 37 (in particular, Subcommittee 4, dealing with the standardisation of linguistic annotations and resources).

Combining a Similar Coefficient Identification Algorithm with the Boundary Element Method

The boundary element method (BEM) has been applied successfully to many engineering problems during the last decades. Compared with domain type methods like the finite element method (FEM) or the finite difference method (FDM) the BEM can handle problems where the medium extends to infinity much easier than domain type methods as there is no need to develop special boundary conditions (quiet or absorbing boundaries) or infinite elements at the boundaries introduced to limit the domain studied. The determination of the dynamic stiffness of arbitrarily shaped footings is just one of these fields where the BEM has been the method of choice, especially in the 1980s. With the continuous development of computer technology and the available hardware equipment the size of the problems under study grew and, as the flop count for solving the resulting linear system of equations grows with the third power of the number of equations, there was a need for the development of iterative methods with better performance. In [1] the GMRES algorithm was presented which is now widely used for implementations of the collocation BEM. While the FEM results in sparsely populated coefficient matrices, the BEM leads, in general, to fully or densely populated ones, depending on the number of subregions, posing a serious memory problem even for todays computers. If the geometry of the problem permits the surface of the domain to be meshed with equally shaped elements a lot of the resulting coefficients will be calculated and stored repeatedly. The present paper shows how these unnecessary operations can be avoided reducing the calculation time as well as the storage requirement. To this end a similar coefficient identification algorithm (SCIA), has been developed and implemented in a program written in Fortran 90. The vertical dynamic stiffness of a single pile in layered soil has been chosen to test the performance of the implementation. The results obtained with the 3-d model may be compared with those obtained with an axisymmetric formulation which are considered to be the reference values as the mesh quality is much better. The entire 3D model comprises more than 35000 dofs being a soil region with 21168 dofs the biggest single region. Note that the memory necessary to store all coefficients of this single region is about 6.8 GB, an amount which is usually not available with personal computers. In the problem under study the interface zone between the two adjacent soil regions as well as the surface of the top layer may be meshed with equally sized elements. In this case the application of the SCIA leads to an important reduction in memory requirements. The maximum memory used during the calculation has been reduced to 1.2 GB. The application of the SCIA thus permits problems to be solved on personal computers which otherwise would require much more powerful hardware.

Fibras ópticas: interacción dispersion-chirp en sistemas ópticos modulados directamente

En los sistemas de comunicación por fibra óptica, la configuración usualmente empleada para velocidades de transmisión no superiores a 10 Gb/s es la modulación directa del láser (DML). Esta configuración presenta diversas ventajas frente a la modulación externa, como son un bajo coste, simplicidad de diseño, tamaño reducido y una elevada potencia de emisión. Sin embargo, el desplazamiento de la frecuencia nominal del láser (chirp) asociado al DML es un grave inconveniente al que deben enfrentarse los sistemas que trabajan con este modelo de transmisor. En este trabajo se propone un método para la optimización de los sistemas modulados directamente. Este método determina bajo qué condiciones se consigue contrarrestar la dispersión acumulada en el enlace ajustando adecuadamente el chirp del láser y los fenómenos no lineales que se generan en la fibra óptica.

Comunicaciones Ópticas de Banda Ancha con Fase Modulada: "Estudio de la Degradación de la Señal Óptica"

En el presente proyecto final de carrera se lleva a cabo un estudio de los sistemas de comunicaciones ópticas de 100 Gb/s. En la primera parte del proyecto se repasan las principales técnicas de modulación y de recepción de la portadora óptica, se presentan los diferentes formatos avanzados de modulación digital empleados para transmisiones de banda ancha y se discute por qué las modulaciones QPSK y DQPSK ofrecen mejores prestaciones que el resto a 100 Gb/s. La segunda parte compone el grueso del proyecto. Se centra en el estudio y la optimización de los sistemas ópticos de 100 Gb/s que hacen uso de los formatos de fase en cuadratura anteriores. De dicho análisis se pretende conocer cómo se degradan este tipo de señales a medida que se propagan por la fibra a estas velocidades. Intentaremos descubrir además cómo controlar ciertos parámetros de diseño como el ciclo de trabajo de la portadora óptica, el mapa de dispersión del enlace, la potencia inyectada a la fibra, la longitud de los vanos de amplificación …, para conseguir reducir la penalización sufrida por las limitaciones anteriores. La detección óptica coherente, la multiplexación en polarización, fibras de gran área efectiva y elevado coeficiente de dispersión cromática, unidas al uso de los formatos de fase en cuadratura, componen la mejor solución tecnológica para conseguir hacer realidad las transmisiones ópticas a 100 Gb/s de larga y ultra-larga distancia. Con el objetivo de completar el estudio teórico anterior, se diseñará una red óptica de banda ancha sobre la que se aplicarán las técnicas de diseño desarrolladas a lo largo del proyecto.

High data rate modulation of high power 1060-nm DBR tapered lasers with separate contacts

Direct optical modulation at 2.5 Gb/s with amplitude of more than 0.5 W has been demonstrated in single longitudinal mode distributed Bragg reflector tapered lasers emitting at 1060 nm with separated injection of the ridge waveguide and tapered sections. The modulating signal of ~110 mA peak to peak was applied to the ridge waveguide section, yielding a high modulation efficiency of ~5 W/A. The large-signal frequency response of the experimental set-up was limited by the bandwidth of the electrical amplifier rather than by the internal dynamics of the laser, indicating that higher bit rates could be achieved with improved driving electronics.

Comunicaciones Ópticas de Banda Ancha con Fase Modulada: "Estudio de la Degradación de la Señal Óptica"

En el presente proyecto final de carrera se lleva a cabo un estudio de los sistemas de comunicaciones ópticas de 100 Gb/s. En la primera parte del proyecto se repasan las principales técnicas de modulación y de recepción de la portadora óptica, se presentan los diferentes formatos avanzados de modulación digital empleados para transmisiones de banda ancha y se discute por qué las modulaciones QPSK y DQPSK ofrecen mejores prestaciones que el resto a 100 Gb/s. La segunda parte compone el grueso del proyecto. Se centra en el estudio y la optimización de los sistemas ópticos de 100 Gb/s que hacen uso de los formatos de fase en cuadratura anteriores. De dicho análisis se pretende conocer cómo se degradan este tipo de señales a medida que se propagan por la fibra a estas velocidades. Intentaremos descubrir además cómo controlar ciertos parámetros de diseño como el ciclo de trabajo de la portadora óptica, el mapa de dispersión del enlace, la potencia inyectada a la fibra, la longitud de los vanos de amplificación …, para conseguir reducir la penalización sufrida por las limitaciones anteriores. La detección óptica coherente, la multiplexación en polarización, fibras de gran área efectiva y elevado coeficiente de dispersión cromática, unidas al uso de los formatos de fase en cuadratura, componen la mejor solución tecnológica para conseguir hacer realidad las transmisiones ópticas a 100 Gb/s de larga y ultra-larga distancia. Con el objetivo de completar el estudio teórico anterior, se diseñará una red óptica de banda ancha sobre la que se aplicarán las técnicas de diseño desarrolladas a lo largo del proyecto.

Modelo Híbrido para la Ayuda al Capitán

En esta Tesis se plantea una nueva forma de entender la evacuación apoyándonos en tecnologías existentes y accesibles que nos permitirán ver este proceso como un ente dinámico. Se trata de una metodología que implica no solo el uso de herramientas de análisis que permitan la definición de planes de evacuación en tiempo real, sino que también se apunta hacia la creación de una infraestructura física que permita alimentar con información actualizada al sistema de forma que, según la situación y la evolución de la emergencia, sea posible realizar planes alternativos que se adapten a las nuevas circunstancias. En base a esto, el sistema asimilará toda esa información y aportará soluciones que faciliten la toma de decisiones durante toda la evolución del incidente. Las aportaciones originales de esta Tesis son múltiples y muy variadas, pudiéndolas resumir en los siguientes puntos: 1. Estudio completo del estado del arte: a. Detección y análisis de diferentes proyectos a nivel internacional que de forma parcial tratan algunos aspectos desarrollados en la Tesis. b. Completo estudio a nivel mundial del software desarrollado total o parcialmente para la simulación del comportamiento humano y análisis de procesos de evacuación. Se ha generado una base de datos que cataloga de forma exhaustiva estas aplicaciones, permitiendo realizar un completo análisis y posibilitando la evolución futura de los contenidos de la misma. En la tesis se han analizado casi un centenar de desarrollos, pero el objetivo es seguir completando esta base de datos debido a la gran utilidad y a las importantes posibilidades que ofrece. 2. Desarrollo de un importante capítulo que trata sobre la posibilidad de utilizar entornos virtuales como alternativa intermedia al uso de simuladores y simulacros. En esta sección se divide en dos bloques: a. Ensayos en entornos reales y virtuales. b. Ensayos en entornos virtuales (pruebas realizadas con varios entornos virtuales). 3. Desarrollo de e-Flow net design: paquete de herramientas desarrolladas sobre Rhinoceros para el diseño de la red de evacuación basada en los elementos definidos en la tesis: Nodes, paths, Relations y Areas. 4. Desarrollo de e-Flow Simulator: Conjunto de herramientas que transforman Rhinoceros en un simulador 3D de comportamiento humano. Este simulador, de desarrollo propio, incorpora un novedoso algoritmo de comportamiento a nivel de individuo que incluye aspectos que no se han encontrado en otros simuladores. Esta herramienta permite realizar simulaciones programadas de grupos de individuos cuyo comportamiento se basa en el análisis del entorno y en la presencia de referencias dinámicas. Incluye otras importantes novedades como por ejemplo: herramientas para análisis de la señalización, elementos de señalización dinámica, incorporación sencilla de obstáculos, etc. También se ha creado una herramienta que posibilita la implementación del movimiento del propio escenario simulando la oscilación del mismo, con objeto de reflejar la influencia del movimiento del buque en el desplazamiento de los individuos. 5. En una fase avanzada del desarrollo, se incorporó la posibilidad de generar un vídeo de toda la simulación, momento a partir del cual, se han documentado todas las pruebas (y se continúan documentando) en una base de datos que recoge todas las características de las simulaciones, los problemas detectados, etc. Estas pruebas constituyen, en el momento en que se ha cerrado la redacción de la Tesis, un total de 81 GB de datos. Generación y análisis de rutas en base a la red de evacuación creada con e-Flow Net design y las simulaciones realizadas con e-Flow Net simulator. a. Análisis para la optimización de la configuración de la red en base a los nodos por área existentes. b. Definición de procesos previos al cálculo de rutas posibles. c. Cálculo de rutas: i. Análisis de los diferentes algoritmos que existen en la actualidad para la optimización de rutas. ii. Desarrollo de una nueva familia de algoritmos que he denominado “Minimum Decision Algorithm (MDA)”, siendo los algoritmos que componen esta familia: 1. MDA básico. 2. MDA mínimo. 3. MDA de no interferencia espacial. 4. MDA de expansión. 5. MDA de expansión ordenada para un único origen. 6. MDA de expansión ordenada. iii. Todos estos algoritmos se han implementado en la aplicación e-Flow creada en la Tesis para el análisis de rutas y que constituye el núcleo del Sistema de Ayuda al Capitán. d. Determinación de las alternativas para el plan de evacuación. Tras la definición de las rutas posibles, se describen diferentes procesos existentes de análisis por ponderación en base a criterios, para pasar finalmente a definir el método de desarrollo propio propuesto en esta Tesis y cuyo objetivo es responder en base a la población de rutas posibles obtenidas mediante los algoritmos MDA, qué combinación de rutas constituyen el Plan o Planes más adecuados para cada situación. La metodología creada para la selección de combinaciones de rutas que determinan un Plan completo, se basa en cuatro criterios básicos que tras su aplicación ofrecen las mejores alternativas. En esta fase también se incluye un complejo análisis de evolución temporal que incorpora novedosas definiciones y formulaciones. e. Derivado de la definición de la metodología creada en esta Tesis para la realización de los análisis de evolución temporal, se ha podido definir un nuevo teorema matemático que se ha bautizado como “Familia de cuadriláteros de área constante”. 7. Especificación de la infraestructura física del Sistema de Ayuda al Capitán: parte fundamental de sistema es la infraestructura física sobre la que se sustentaría. Esta infraestructura estaría compuesta por sensores, actuadores, aplicaciones para dispositivos móviles, etc. En este capítulo se analizan los diferentes elementos que la constituirían y las tecnologías implicadas. 8. Especificación de la infraestructura de servicios. 9. Creación del Blog Virtual Environments (http://epcinnova-virtualenvironments.blogspot.com.es/) en el que se han publicado todas las pruebas realizadas en el capítulo que analiza los entornos virtuales como alternativa a los simuladores y a los ensayos en laboratorio o los simulacros, incluyendo en muchos casos la posibilidad de que el visitante del blog pueda realizar la simulación en el entorno virtual. Este blog también incluye otras secciones que se han trabajado durante la Tesis: • Recopilación de diferentes entornos virtuales existentes. • Diagrama que recopila información sobre accidentes tanto en el ámbito marítimo como en el terrestre (en desarrollo). • Esquema propuesto para el acopio de información obtenida a partir de un simulacro. 10. Esta Tesis es la base para el proyecto e-Flow (nombre de una de las aplicaciones que desarrolladas en esta obra), un proyecto en el que el autor de esta Tesis ha trabajado como Project Manager. En el proyecto participa un consorcio de empresas y la UPM, y tiene como objetivo trasladar a la realidad gran parte de los planteamientos e ideas presentadas en esta Tesis. Este proyecto incluye el desarrollo de la infraestructura física y de servicios que permitirán, entre otras cosas, implementar en infraestructuras complejas una plataforma que posibilita la evacuación dinámica y un control ubicuo de los sistemas de monitorización y actuación implementados. En estos momentos se está finalizando el proyecto, cuyo objetivo final es la implementación de un piloto en un Hospital. También destacamos los siguientes avances a nivel de difusión científico-tecnológico: • Ponencia en el “52 congreso de la Ingeniería Naval en España” presentando un artículo “e-Flow- Sistema integral inteligente de soporte a la evacuación”. En este artículo se trata tanto el proyecto e-Flow del que soy Project Manager, como esta Tesis Doctoral, al ser temas estrechamente vinculados. En 2014 se publicó en dos números de la Revista Ingeniería Naval el artículo presentado a estas jornadas. • Co-autor en el artículo “E-Flow: A communication system for user notification in dynamic evacuation scenarios” presentado en el 7th International Conference on Ubicuous Computing & Ambient Intelligence (UCAMI) celebrado en Costa Rica. Por último, una de las aportaciones más interesantes, es la definición de un gran número de líneas de investigación futuras en base a todos los avances realizados en esta Tesis. ABSTRACT With this Thesis a new approach for understanding evacuation process is considered, taking advantage of the existing and open technologies that will allow this process to be interpreted as a dynamic entity. The methodology involves not only tools that allows on.-time evacuation plans, but also creates a physical insfrastructure that makes possible to feed the system with information on real time so, considering in each moment the real situation as well as the specific emergency development it will be feasible to generate alternative plans that responds to the current emergency situation. In this respect, the system will store all this information and will feedback with solutions that will help the decision making along the evacuation process. The innovative and singular contributions of this Thesis are numerous and rich, summarised as follows: 1.- Complete state-of-art study: a. Detection and analysis of different projects on an international level that, although partially, deal with some aspects developed in this Thesis. b. Thorough study at a international level of the developed software - total or partially done - for the simulation of the human behaviour and evacuation processes analysis. A database has been generated that classifies in detail these applications allowing to perform a full analysis and leading to future evolution of its contents. Within the Thesis work, almost a hundred of developments have been analysed but the purpose is to keep up updating this database due to the broad applications and possibilities that it involves. 2. Development of an important chapter that studies the possibility of using virtual scenarios as mid-term alternative for the use of simulations. This section is divided in two blocks: a. Trials in virtual and real scenarios b. Trials in virutal scenarios (trials performed with several ones). 3. E-Flow net design development: Set of tools developed under Rhinoceros for the evacuation net design based on the elements defined in the Thesis: Nodes, Paths, Relations, Areas 4. E-Flow simulator development: Set of tools that uses Rhinoceros as a 3D simulator of human behaviour. This simulator, of my own design, includes a new and original algorithm of human behaviour that involves aspects that are not found in other simulators. This tool allows to perform groups programmed simulations which behaviour is based on their enviroment analysis and presence of dynamic references. It includes other important innovations as for example: tools for signals analysis, dynamic signal elements, easy obstacle adding etc... More over, a tool that allows the own scenario movement implementation has been created by simulating the own oscillation movement, with the purpose of playing the vessel movement's influences in the individuals' displacements. 5. In an advanced stage of the development, the possibility of generating a video recording of all the simulation was also integrated, then from that moment all tests have been filed (and keep on doing so) in a database that collects all simulation characteristics, failures detected, etc. These stored tests amounts to a total of 81 GB at the moment of finishing the Thesis work. Generation and analysis of paths regarding the evacuation net created with E-Flow design and the simulations performed with E-Flow net Simulator. a. Analysis for the optimisation of the network configuration based in the existing nodes per area. b. Definition of the processes previous to the calculation of the feasible paths c. Paths calculation: i. Analysis of the different algorithms on existance nowadays for the routes optimisation. ii. Development of a new family of algorithms that I have called “Minimum Decision Algorithm (MDA)”, being composed of: 1. MDA basic 2. MDA minimum 3. MDA of not spacial interference 4. MDA of expansion (es de extenderse) o enlargement ( es de crecimiento) 5. MDA of organised expansion for a single origin (of organised enlargement for a single origin) 6. MDA of organised expansion (of organised enlargement) iii. All these algorithms have been implemented in the E-Flow application created in the Thesis dfor the routes analysis and it is the core of the Captain's support system. d. Determination of the alternatives for the evacuation plan. After defining all possible paths, different processes of analysis existing for weighing-based criteria are described, thus to end defining the own development method proposed in this Thesis and that aims to respond in an agreggation of possible routes basis obtained by means of the MDA algorithms what is the routes' combination more suitable for the Plan or Plans in every situation. The methodology created fot the selection of the combinations of routes that determine a complete Plan is baesd in four basic criteria that after applying, offer the best alternatives. In this stage a complex analysis of the progress along time is also included, that adds original and innovative defintions and formulations. e. Originated from the methodology created in this Thesis for the perfoming of the analysy of the progress along time, a new mathematic theorem has been defined, that has been called as "Family of quadrilateral of constant area". 7. Specification of the physiscal infrastructure of the Captain's help system: essential part is this physical infrastructure that will support it. This system will be made of sensors, actuators, apps for mobile devices etc... Within this chapter the different elements and technologies that make up this infrastructure will be studied. 8. Specification for the services infrastructure. 9. Start up of the Blog. " Virtual Environments (http://epcinnova-virtualenvironments.blogspot.com.es/)" in which all tests performed have been published in terms of analysis of the virtual enviroments as alternative to the simulators as well as to the laboratory experiments or simulations, including in most of the cases the possibility that the visitor can perform the simulation within the virtual enviroment. This blog also includes other sections that have been worked along and within this Thesis: - Collection of different virtual scenarios existent. - Schema that gathers information concerning accidents for maritime and terrestrial areas (under development) - Schema proposed for the collecting of information obtained from a simulation. 10. This Thesis is the basis of the E-Flow project (name of one of the applications developed in this work), a project in which the Thesis' author has worked in as Project Manager. In the project takes part a consortium of firms as well as the UPM and the aim is to bring to real life most part of the approaches and ideas contained in this Thesis. This project includes the development of the physical infrastructure as well as the services that will allow, among others, implement in complex infrastrucutres a platform that will make possible a dynamic evacuation and a continuous control of the monitoring and acting systems implemented. At the moment the project is getting to an end which goal is the implementation of a pilot project in a Hospital. We also would like to highlight the following advances concerning the scientific-technology divulgation: • Talk in the " 52th Congress of the Naval Engineering in Spain" with the article "E-Flow . Intelligent system integrated for supporting evacuation". This paper is about project E-Flow which I am Project Manager of, as well as this Thesis for the Doctorate, being both closely related. Two papers published In 2014 in the Naval Engineering Magazine. • Co-author in the article “E-Flow: A communication system for user notification in dynamic evacuation scenarios” [17] introduced in the 7th International Conference on Ubicuous Computing & Ambient Intelligence (UCAMI) held in Costa Rica. Last, but not least, one of the more interesting contributions is the defintion of several lines of research in the future, based on the advances made in this Thesis.

Efficient parallelization of a regional ocean model for the western Mediterranean Sea

This paper focuses on the parallelization of an ocean model applying current multicore processor-based cluster architectures to an irregular computational mesh. The aim is to maximize the efficiency of the computational resources used. To make the best use of the resources offered by these architectures, this parallelization has been addressed at all the hardware levels of modern supercomputers: firstly, exploiting the internal parallelism of the CPU through vectorization; secondly, taking advantage of the multiple cores of each node using OpenMP; and finally, using the cluster nodes to distribute the computational mesh, using MPI for communication within the nodes. The speedup obtained with each parallelization technique as well as the combined overall speedup have been measured for the western Mediterranean Sea for different cluster configurations, achieving a speedup factor of 73.3 using 256 processors. The results also show the efficiency achieved in the different cluster nodes and the advantages obtained by combining OpenMP and MPI versus using only OpenMP or MPI. Finally, the scalability of the model has been analysed by examining computation and communication times as well as the communication and synchronization overhead due to parallelization.

Hepatitis C virus and other Flaviviridae viruses enter cells via low density lipoprotein receptor

Endocytosis of the Flaviviridae viruses, hepatitis C virus, GB virus C/hepatitis G virus, and bovine viral diarrheal virus (BVDV) was shown to be mediated by low density lipoprotein (LDL) receptors on cultured cells by several lines of evidence: by the demonstration that endocytosis of these virus correlated with LDL receptor activity, by complete inhibition of detectable endocytosis by anti-LDL receptor antibody, by inhibition with anti-apolipoprotein E and -apolipoprotein B antibodies, by chemical methods abrogating lipoprotein/LDL receptor interactions, and by inhibition with the endocytosis inhibitor phenylarsine oxide. Confirmatory evidence was provided by the lack of detectable LDL receptor on cells known to be resistant to BVDV infection. Endocytosis via the LDL receptor was shown to be mediated by complexing of the virus to very low density lipoprotein or LDL but not high density lipoprotein. Studies using LDL receptor-deficient cells or a cytolytic BVDV system indicated that the LDL receptor may be the main but not exclusive means of cell entry of these viruses. Studies on other types of viruses indicated that this mechanism may not be exclusive to Flaviviridae but may be used by viruses that associate with lipoprotein in the blood. These findings provide evidence that the family of LDL receptors may serve as viral receptors.

Increasing the quality of seismic interpretation

Euan Macrae was funded by a NERC Open CASE PhD award (NE/F013728/1) with Midland Valley Exploration Ltd. as the industry partner. We thank the 763 geoscientists for their participation, and in particular, the reference experts who gave their time freely to the project. Marian Scott (University of Glasgow, UK) is thanked for assisting with the statistical analysis. Four reviewers are thanked for their constructive comments which improved the manuscript.

Global modulation of cellular transcription by human cytomegalovirus is initiated by viral glycoprotein B

Human cytomegalovirus (HCMV) infection alters the expression of many cellular genes, including IFN-stimulated genes (ISGs) [Zhu, H., Cong, J.-P., Mamtora, G., Gingeras, T. & Shenk, T. (1998) Proc. Natl. Acad. Sci. USA 95, 14470–14475]. By using high-density cDNA microarrays, we show that the HCMV-regulated gene expression profile in fibroblasts does not differ substantially from the response generated by IFN. Furthermore, we identified the specific viral component triggering this response as the envelope glycoprotein B (gB). Cells treated with gB, but not other herpesviral glycoproteins, exhibited the same transcriptional profile as HCMV-infected cells. Thus, the interaction of gB with its as yet unidentified cellular receptor is the principal mechanism by which HCMV alters cellular gene expression early during infection. These findings highlight a pioneering paradigm for the consequences of virus–receptor interactions.