Some examples of modeling in chemical engineering: thermal treatment of polymers, phase equilibrium calculations and process design

Presentation submitted to PSE Seminar, Chemical Engineering Department, Center for Advanced Process Design-making (CAPD), Carnegie Mellon University, Pittsburgh (USA), October 2012.

Coordination polymers, metal–organic frameworks and the need for terminology guidelines

Coordination polymers (CPs) and metal–organic frameworks (MOFs) are among the most prolific research areas of inorganic chemistry and crystal engineering in the last 15 years, and yet it still seems that consensus is lacking about what they really are, or are not.

Terminology of metal–organic frameworks and coordination polymers (IUPAC Recommendations 2013)

A set of terms, definitions, and recommendations is provided for use in the classification of coordination polymers, networks, and metal–organic frameworks (MOFs). A hierarchical terminology is recommended in which the most general term is coordination polymer. Coordination networks are a subset of coordination polymers and MOFs a further subset of coordination networks. One of the criteria an MOF needs to fulfill is that it contains potential voids, but no physical measurements of porosity or other properties are demanded per se. The use of topology and topology descriptors to enhance the description of crystal structures of MOFs and 3D-coordination polymers is furthermore strongly recommended.

Rapid carbon nanotubes suspension in organic solvents using organosilicon polymers

A strategy for a simple dispersion of commercial multi-walled carbon nanotubes (MWCNTs) using two organosilicones, polycarbosilane SMP10 and polysilazane Ceraset PSZ20, in organic solvents such as cyclohexane, tetrahydrofuran (THF), m-xylene and chloroform is presented. In just a few minutes the combined action of sonication and the presence of Pt(0) catalyst is sufficient to obtain a homogeneous suspension, thanks to the rapid hydrosilylation reaction between SiH groups of the polymer and the CNT sidewall. The as-produced suspensions have a particle size distribution <1μm and remain unchanged after several months. A maximum of 0.47 and 0.50mg/ml was achieved, respectively, for Ceraset in THF and SMP10 in chloroform. Possible applications as polymeric and ceramic thin films or aerogels are presented.

Radiation-induced reactions in swollen polymers /

The content was printed on only one side of the paper.

Radiation-induced reactions in swollen polymers /

The content was printed on only one side of the paper.

Stress history measurements with piezoelectric crystals : preliminary report /

"U.S. Atomic Energy Commission Plowshare Program ; Project Gnome, Carlsbad, New Mexico, December 10, 1961"--Cover.

Infrared spectra of polymers and resins.

Cover title: Infrared spectra of plastics and resins.

The electrical admittance of a homogeneous polarized fully electroded circular disc, loss-less and mechanically free : analysis, including Rayleigh correction, data for routine determination of elastic modulus and Piezoelectric coupling, and discussion of limitation of correction, anisotrophy parameters involved, and deductions concerning dimensional standarization /

"ONR Contract No. Nonr-1055(00)."

Synthesis and evaluation of new polymers prepared by sterospecific catalysis. Materials Central, Contract no. AF33(616)-6866, Project no. 7340.

"Prepared by the Polytechnic Institute of Brooklyn...under the supervision of Dr. C.G. Overberger."

Rheology of polymers

Mode of access: Internet.

Fundamentals of high polymers.

Includes bibliography.

Mechanical properties of polymers.

Includes bibliographical references.

Polymers and resins: their chemistry and chemical engineering.

Includes bibliography.

Modelling the input-output behaviour of piezoelectric structural health monitoring systems for composite plates

This paper investigates the input-output characteristics of structural health monitoring systems for composite plates based on permanently attached piezoelectric transmitter and sensor elements. Using dynamic piezoelectricity theory and a multiple integral transform method to describe the propagating and scattered flexural waves an electro-mechanical model for simulating the voltage input-output transfer function for circular piezoelectric transmitters and sensors adhesively attached to an orthotropic composite plate is developed. The method enables the characterization of all three physical processes, i.e. wave generation, wave propagation and wave reception. The influence of transducer, plate and attached electrical circuit characteristics on the voltage output behaviour of the system is examined through numerical calculations, both in frequency and the time domain. The results show that the input-output behaviour of the system is not properly predicted by the transducers' properties alone. Coupling effects between the transducers and the tested structure have to be taken into account, and adding backing materials to the piezoelectric elements can significantly improve the sensitivity of the system. It is shown that in order to achieve maximum sensitivity, particular piezoelectric transmitters and sensors need to be designed according to the structure to be monitored and the specific frequency regime of interest.