Ordering and stability in conducting polypyrrole

X-ray diffraction (XRD) was employed to characterize electrochemically synthesized polypyrrole (PPy) films with 1,5-naphthalene disulfonate (1,5-NDS) counterions treated with simple acid and base. Results show that the as-synthesized film is amorphous with short-range ordering in the polymer backbone. This ordering is soon lost after thermal ageing at 150°C for 60 days and there is evidence of counterion degradation. Base treatment of the PPy/1,5-NDS films has similar effects leading to a complete loss of ordering in the polymer backbone and dedoping of the polymer. Acid treatment at high temperatures increases the ordering of the polymer backbone and results in the development of a secondary interdopant peak confirming that ion exchange has occurred. Conductivity of the PPy was also increased substantially. The enhanced ordering was maintained even after thermal ageing. Room-temperature acid treatment also results in improved ordering of the polymer as well as the counterion but the increase in conductivity is only marginal and most of the ordering is soon lost after thermal ageing. Increase in ordering of the polymer structure seems to lead to better conductivity, although not necessarily improved thermal stability.

Mechanisms governing the enhanced thermal stability of acid and base treated polypyrrole

One of the major problems associated with the use of polypyrrole (PPy) in a practical engineering application is its poor thermal stability at elevated temperatures, especially in the presence of oxygen and moisture. Several authors have shown that enhanced stability can be achieved through treatment with simple acids and bases. This paper presents a summary of the possible structural changes which occur as a result of these treatments and those that appear to be related to enhanced conductivity stability. A slight increase in conductivity (10–20%) is observed for acid treated PPy films which is found to be the result of protonation of the pyrrole structure. This effect is dramatically enhanced by treatment at high temperatures where an increase in conductivity of >84% can be achieved. Base treatment of the PPy films results in the deprotonation of the pyrrole structure leading to the loss of conductivity (>40%). Preliminary X-ray Photoelectron Spectroscopy (XPS) results indicate that both acid and base treatment resulted in the elimination of reactive sites for oxygen. Long term thermal ageing of these treated films were conducted at 150 °C in air. The conductivity decay behaviour was found to follow multiple first order chemical reaction kinetics.

Lithium-polymer battery based on an ionic liquid–polymer electrolyte composite for room temperature applications

A lithium-polymer battery based on an ionic liquid–polymer electrolyte (IL–PE) composite membrane operating at room temperature is described. Utilizing a polypyrrole coated LiV₃O₈ cathode material, the cell delivers >200 mAh g⁻¹ with respect to the mass of the cathode material. Discharge capacity is slightly higher than those observed for this cathode material in standard aprotic electrolytes; it is thought that this is the result of a lower solubility of the LiV₃O₈ material in the IL–PE composite membrane.

A study of acid/base treatments of polypyrrole films using 13C n.m.r. spectroscopy

Electrodeposited polypyrrole films prepared with paratoluenesulfonate (pTS), dodecylsulfate (DDS) and perchlorate anions were treated with acidic and basic solutions, and their structure was investigated by 13C solid state n.m.r. spectroscopy. This technique has confirmed that pTS is completely removed from the film in both acidic and basic solutions whilst DDS is only partially removed and tends to decompose upon treatment with H2SO4. The appearance of shoulders at 143 ppm upon treatment with 0.5 M base indicates formation of a quinoid pyrrole structure. Substitution on the β-carbon by OH cannot be confirmed from the present spectra. Stronger base causes a more dramatic change in the polypyrrole backbone with an obvious increase in the electron density on the β-carbons, consistent with the reduction of the carbon backbone. There is no indication of quinoid units in this case. Acid treatments result in considerable broadening of the main 127 ppm polypyrrole peak.

Structural characterization of conducting polypyrrole using 13C cross-polarization/magic-angle spinning solid-state nuclear magnetic resonance spectroscopy

¹³C nuclear magnetic resonance (n.m.r.) has been used to study polypyrrole and N-substituted polypyrrole in the solid state. The extent of oxidation appears to be counterion-dependent; in particular, the quinoid structure appears favoured in the films prepared with dodecyl sulfate. Resonances associated with the quinoid unit are lost upon reduction of the polypyrrole film, which supports the idea that the quinoid structure is associated with the oxidized form of polypyrrole. N-substituted polypyrroles have a more distinct resonance at 110 ppm, which is linked to lower degrees of oxidation or charge delocalization in these systems. The decrease in conductivity of polypyrrole upon thermal ageing in air is associated with both the loss of counterion (‘thermal dedoping’) and the decomposition of the quinoid structure in the polymer backbone. There is no indication of carbonyl formation in the solid-state n.m.r. spectra obtained in the present study.

Electrochemical synthesis of polypyrrole in ionic liquids

Electrochemical synthesis of inherently conducting polymers such as polypyrrole is traditionally performed in a molecular solvent/electrolyte system such acetonitrile/lithium perchlorate. We report the use of ionic liquids 1-butyl-3-methylimidazolium hexafluorophosphate, 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl) amide and N,N-butylmethylpyrrolidinium bis(trifluoromethanesulfonyl) amide, both as the growth medium and as an electrolyte for the electrochemical cycling of polypyrrole films. Use of the ionic liquid as the growth medium results in significantly altered film morphologies and improved electrochemical activities.

Solid state NMR analysis of polypyrrole grown in a phosphonium ionic liquid

³¹P, ¹⁹F and ¹³C solid state NMR analysis has been used to investigate the intercalation/de-intercalation of both anions and cations in electrochemically synthesized polypyrrole films. Use of a phosphonium-based ionic liquid, tri(hexyl)(tetradecyl)phosphonium bis(trifluoromethanesulfonyl)amide, allows the separate detection of the cation and anion by analysis of the phosphorous and fluorine resonances, respectively. Initial results indicate the incorporation of both cations and anions during film growth in the ionic liquid. There is a notable change in the ³¹P chemical shift of the cation on incorporation into the film, consistent with a significant change in environment compared to the pure ionic liquid. Despite its large size, the phosphonium cation can be completely expelled from the film by oxidation.

Platinum electrodeposition for polymer electrolyte membrane fuel cells

A novel electrodeposition technique for preparing the catalyst layer in polymer electrolyte membrane fuel cells has been designed, which may enable an increase in the level of platinum utilisation currently achieved in these systems. This method consists of a two-step procedure involving the impregnation of platinum ions into a preformed catalyst layer (via an ion-exchange into the Nafion polymer electrolyte), followed by a potentiostatic reduction. The concentration of Nafion within the catalyst layer was found to have a significant bearing on the size of the platinum deposits. The preparation of catalyst layers containing a desired platinum loading should also be possible using this method. Surface areas of the platinum deposits were determined using cyclic voltammetry. The prepared catalyst was compared with a conventional electrode made from E-TEK Pt/C. Scanning electron microscopy was used to investigate the dispersion of the platinum particles. Platinum loadings were determined quantitatively by atomic absorption spectroscopy.

Enhanced thermal properties and morphology of ion-exchanged polypyrrole films

The thermal stability of electrochemically prepared polypyrrole (PPy) films with p-toluenesulfonate (pTS) or perchlorate (ClO₄⁻) counterion (PPy/pTS and PPy/ClO₄⁻) is improved by simple treatment with aqueous sulfuric acid, sodium sulfate or sodium bisulfate. The degree of stabilization achieved depends on the solution, temperature and duration of treatment. Although the mechanism for improved stability is not yet clear, it is apparent that the level of ion exchange and the original polymer microstructure are important. A model for the conductivity decay as a function of thickness has been proposed. The early stages of ion exchange are not symmetrical, and diffusion is facilitated at the electrode side of the film. Furthermore, X-ray diffraction shows no evidence of morphological change after treatment of PPy/pTS (43 μm), but in PPy/pTS (12 μm) and PPy/ClO₄⁻ (41 μm) films an additional peak is indicative of more ordered structure following treatment. The glass transition temperature, T_g, of PPy/pTS and PPy/ClO₄⁻ films obtained by modulated differential scanning calorimetry is approximately 155°C.

Ion exchange, anisotropic structure and thermal stability of polypyrrole films

The thermal stability of electrochemically prepared polypyrrole (PPy) films with p-toluene sulfonate (pTS) or perchlorate (CIOP₄⁻) counter ion (PPy/pTS and PPy/ClO₄⁻) is improved by simple treatment with aqueous sulfuric acid, sodium sulfate or sodium bisulfate. The degree of stabilization achieved depends on the solution, temperature and duration of treatment. PPy/pTS is easily stabilized and thick films (43μm) retain 90 % of the initial conductivity after long period (300 h) at 150 °C, while thinner films (12 μm) retain slightly less (70 %). A model for the conductivity decay has been proposed. Although the mechanism for improved stability is not yet clear it is apparent that the level of ion exchange and the original polymer microstructure are important. The early stages of ion exchange are not symmetrical and diffusion is facilitated at the electrode side of the film. Furthermore, X-ray diffraction shows no evidence of morphological change after treatment of thick PPy/pTS but in thin PPy/pTS and PPy/ClO₄⁻ films an additional peak is indicative of more ordered structure following treatment. These observation may imply that there is a higher density of crosslinks and branching at the growth side than at the electrode side of the film.

Solid state actuators based on polypyrrole and polymer-in-ionic liquid electrolytes

Novel polymer-in-ionic liquid electrolytes (PILEs) have been developed for solid state electrochemical actuators based on polypyrrole. The active polymer electrodes are readily oxidized/reduced without degradation in the PILE. It was found that the actuator cycle life is significantly enhanced in the PILE as is the ‘shelf life’ of the device.

Effects of backwashing on PVDF membrane fouling by organic foulants

Membrane is usually subject to fouling by various organic foulants, such as yeast, protein and sodium alginate during filtration. Backwashing is a common practice to reduce membrane fouling. It is essential to evaluate the effects of backwashing on fouling in order to optimize operational parameters. In this experiment, poly(vinylidene fluoride) (PVDF) membranes were used to filter organic foulants from suspensions in a dead-end stirred cell. Three types of organic foulants including yeast, protein and sodium alginate which were stained with fluorescent dyes before filtration were used with different combinations in the experiments. After filtration, the PVDF membrane was backwashed.

Consequently, a stack of images, instrumental data and sample data were captured from the fouling layers on the PVDF membrane surface using confocal laser scanning microscope (CLSM) and its associated image acquisition software LAS AF. Then, the quality of the images was enhanced for better visualization and a set of quantitative fouling data were derived by using the software code developed by the project team at Deakin University.

This collection contains raw image data of poly(vinylidene fluoride) (PVDF) membrane’s fouling layer when three types of organic foulants present, which are captured by confocal laser scanning microscopy (CLSM) and its software, and the instrumental and sample metadata, the processed image data and the geometrical structure properties of the fouling layer. By comparing with the same membrane without backwashing, the efficiency of backwashing was computed.

This data collection would be useful to evaluate the backwashing efficiency of PVDF membrane in order to optimize frequency and operational conditions of backwashing by membrane materials researchers and water researchers.

An investigation of polypyrrole coated conductive textiles: this research aimed at clarifying some issues occurred in the research project on coloured conductive textiles

Coloured conducting textiles have shown a wide range of potential applications in heating fabrics, electromagnetic wave absorption, and wearable optoelectronic devices. This research aimed at clarifying some issues occurred in the research project on coloured conductive textiles. The investigation firstly clarified a possible chemical reaction that took place between a commercial dispersing dye (Terasil Red G) and the conducting polymer polypyrrole, through chemical separation, structural identification and spectrum characterisations. Then, a series of acidic dyes were introduced into polypyrrole matrix during the vapour coating of conducting polymer on the wool fabrics. Colour and thermal stability studies were conducted. Finally, the polypyrrole nanoparticles (particle size several~200nm) were prepared by a microemulsion polymerisation technique. An acid dye was used as the dopant to re-dope the nanoparticles. The effect of the acidic dye on the optical absorption of nanoparticles was studied. Applying the conducting nanoparticles on wool fabrics may open an alternative path to achieve the coloured conducting textiles.