Compact Coplanar Waveguide Fed Ground Meandered Antenna for Wireless Application

A compact Co-Planar Waveguide (CPW) fed antenna operating at 2.4GHz with 300MHz 2:1 VSWR bandwidth is presented. Compared to a conventional quarter wavelength CPW fed monopole antenna, the aperture area reduction of the present antenna is 85%. The prototype antenna fabricated on a substrate of εr = 4.4 and thickness 1.6mm is only 22x10x1.6mm3. This much size reduction and impedance matching is achieved by adjusting the signal to ground plane separation and meandering the ground plane of a 50Ω CPW transmission line

Frequency Coded Chipless RFID Tag using Spurline Resonators

A novel compact chipless RFID tag using spurline resonators is discussed in this paper. The detection of the tag's ID is using the spectral signature of a spurline resonator circuit. The tag has a data capacity of 8-bits in the range 2.38 to 4.04 GHz. The tag consists of a spurline multiresonating circuit and two cross polarized antennas. The prototype of the tag is fabricated on a substrate CMET/ LK4.3 of dielectric constant 4.3 and loss tangent 0.0018. The measured results show that group delay response can also be used to decode the tag’s identity

A Compiler Integrated Assistance for Optimum Data Allocation in Banked Memory Embedded Processors

Bank switching in embedded processors having partitioned memory architecture results in code size as well as run time overhead. An algorithm and its application to assist the compiler in eliminating the redundant bank switching codes introduced and deciding the optimum data allocation to banked memory is presented in this work. A relation matrix formed for the memory bank state transition corresponding to each bank selection instruction is used for the detection of redundant codes. Data allocation to memory is done by considering all possible permutation of memory banks and combination of data. The compiler output corresponding to each data mapping scheme is subjected to a static machine code analysis which identifies the one with minimum number of bank switching codes. Even though the method is compiler independent, the algorithm utilizes certain architectural features of the target processor. A prototype based on PIC 16F87X microcontrollers is described. This method scales well into larger number of memory blocks and other architectures so that high performance compilers can integrate this technique for efficient code generation. The technique is illustrated with an example

FEM based Virtual Prototyping and Design of Third Harmonic Excitation System for Low Voltage Brushless Alternators

Salient pole brushless alternators coupled to IC engines are extensively used as stand-by power supply units for meeting in- dustrial power demands. Design of such generators demands high power to weight ratio, high e ciency and low cost per KVA out- put. Moreover, the performance characteristics of such machines like voltage regulation and short circuit ratio (SCR) are critical when these machines are put into parallel operation and alterna- tors for critical applications like defence and aerospace demand very low harmonic content in the output voltage. While designing such alternators, accurate prediction of machine characteristics, including total harmonic distortion (THD) is essential to mini- mize development cost and time. Total harmonic distortion in the output voltage of alternators should be as low as possible especially when powering very sophis- ticated and critical applications. The output voltage waveform of a practical AC generator is replica of the space distribution of the ux density in the air gap and several factors such as shape of the rotor pole face, core saturation, slotting and style of coil disposition make the realization of a sinusoidal air gap ux wave impossible. These ux harmonics introduce undesirable e ects on the alternator performance like high neutral current due to triplen harmonics, voltage distortion, noise, vibration, excessive heating and also extra losses resulting in poor e ciency, which in turn necessitate de-rating of the machine especially when connected to non-linear loads. As an important control unit of brushless alternator, the excitation system and its dynamic performance has a direct impact on alternator's stability and reliability. The thesis explores design and implementation of an excitation i system utilizing third harmonic ux in the air gap of brushless al- ternators, using an additional auxiliary winding, wound for 1=3rd pole pitch, embedded into the stator slots and electrically iso- lated from the main winding. In the third harmonic excitation system, the combined e ect of two auxiliary windings, one with 2=3rd pitch and another third harmonic winding with 1=3rd pitch, are used to ensure good voltage regulation without an electronic automatic voltage regulator (AVR) and also reduces the total harmonic content in the output voltage, cost e ectively. The design of the third harmonic winding by analytic methods demands accurate calculation of third harmonic ux density in the air gap of the machine. However, precise estimation of the amplitude of third harmonic ux in the air gap of a machine by conventional design procedures is di cult due to complex geome- try of the machine and non-linear characteristics of the magnetic materials. As such, prediction of the eld parameters by conven- tional design methods is unreliable and hence virtual prototyping of the machine is done to enable accurate design of the third har- monic excitation system. In the design and development cycle of electrical machines, it is recognized that the use of analytical and experimental methods followed by expensive and in exible prototyping is time consum- ing and no longer cost e ective. Due to advancements in com- putational capabilities over recent years, nite element method (FEM) based virtual prototyping has become an attractive al- ternative to well established semi-analytical and empirical design methods as well as to the still popular trial and error approach followed by the costly and time consuming prototyping. Hence, by virtually prototyping the alternator using FEM, the important performance characteristics of the machine are predicted. Design of third harmonic excitation system is done with the help of results obtained from virtual prototype of the machine. Third harmonic excitation (THE) system is implemented in a 45 KVA ii experimental machine and experiments are conducted to validate the simulation results. Simulation and experimental results show that by utilizing third harmonic ux in the air gap of the ma- chine for excitation purposes during loaded conditions, triplen harmonic content in the output phase voltage is signi cantly re- duced. The prototype machine with third harmonic excitation system designed and developed based on FEM analysis proved to be economical due to its simplicity and has the added advan- tage of reduced harmonics in the output phase voltage.

Ein XML-basiertes Modell für synchrone Gruppenarbeit auf gemeinsamen Informationsräumen

In dieser Arbeit wird ein generisches Modell fuer synchrone Gruppenarbeit auf gemeinsamen Informationsraeumen entwickelt. Fuer die Entwicklung dieses Modells muessen die Grundfunktionen fuer Anwendungen der synchronen Gruppenarbeit realisiert werden. Neben der Modellierung des Datenraumes (Datenmodell) und der operationellen Schnittstelle (Interaktionsmodell), muessen Mechanismen fuer die Darstellung der Aktivitaeten der Gruppenmitglieder auf dem Informationsraum (Awareness), sowie fuer die Synchronisierung gleichzeitiger Zugriffe verschiedener Benutzer auf dem Datenraum realisiert werden (Nebenlaeufgkeitskontrolle). Das Grundproblem bei der Loesung der Nebenlaeufigkeit liegt bei der Aufgabe der Isolation aus den klassischen ACID-Transaktionen zu gunsten von Awareness. Die rapide Entwicklung von Techniken der mobilen Kommunikation ermoeglicht den Einsatz dieser Geraete fuer den Zugriff auf Daten im Internet. Durch UMTSund WLAN-Technologien koennen Mobilgeraete fuer Anwendungen ueber die reine Kommunikation hinaus eingesetzt werden. Eine natuerliche Folge dieser Entwicklung sind Anwendungen fuer die Zusammenarbeit mehrerer Benutzer. In der Arbeit wird daher auf die Unterstuetzung mobiler Geraete besonderen Wert gelegt. Die Interaktion der Benutzer auf den gemeinsamen Datenraum wird durch einfache Navigationsoperationen mit einem Cursor (Finger) realisiert, wobei der Datenraum durch XML-Dokumente dargestellt wird. Die Visualisierung basiert auf der Transformierung von XML-Dokumenten in andere XML-basierte Sprachen wie HTML oder SVG durch XSLT-Stylesheets. Awareness-Informationen werden, aehnlich dem Fokus/Nimbus-Modell, von der Interaktion der Benutzer und der Ermittlung der sichtbaren Objekte bei dem Benutzer hergeleitet. Fuer eine geeignete Kontrolle der Nebenlaeufigkeit wurde der Begriff der visuellen Transaktion eingefuehrt, wo die Auswirkungen einer Transaktion von anderen Benutzern (Transaktionen) beobachtet werden koennen. Die Synchronisierung basiert auf einem Sperrverfahren und der Einfuehrung der neuen W-Sperre und der Grundoperationen readV und writeV. Das Modell (Groupware-Server) wird in der Arbeit in einem Prototyp implementiert. Weiterhin wird eine Java-Anwendung sowohl auf einem Desktop PC als auch auf einem Pocket PC (iPAQ 3970) implementiert, welche die Einsetzbarkeit dieses Prototyps demonstriert.

Autonomes Performance-Management in dienstorientierten Architekturen

Die Bedeutung des Dienstgüte-Managements (SLM) im Bereich von Unternehmensanwendungen steigt mit der zunehmenden Kritikalität von IT-gestützten Prozessen für den Erfolg einzelner Unternehmen. Traditionell werden zur Implementierung eines wirksamen SLMs Monitoringprozesse in hierarchischen Managementumgebungen etabliert, die einen Administrator bei der notwendigen Rekonfiguration von Systemen unterstützen. Auf aktuelle, hochdynamische Softwarearchitekturen sind diese hierarchischen Ansätze jedoch nur sehr eingeschränkt anwendbar. Ein Beispiel dafür sind dienstorientierte Architekturen (SOA), bei denen die Geschäftsfunktionalität durch das Zusammenspiel einzelner, voneinander unabhängiger Dienste auf Basis deskriptiver Workflow-Beschreibungen modelliert wird. Dadurch ergibt sich eine hohe Laufzeitdynamik der gesamten Architektur. Für das SLM ist insbesondere die dezentrale Struktur einer SOA mit unterschiedlichen administrativen Zuständigkeiten für einzelne Teilsysteme problematisch, da regelnde Eingriffe zum einen durch die Kapselung der Implementierung einzelner Dienste und zum anderen durch das Fehlen einer zentralen Kontrollinstanz nur sehr eingeschränkt möglich sind. Die vorliegende Arbeit definiert die Architektur eines SLM-Systems für SOA-Umgebungen, in dem autonome Management-Komponenten kooperieren, um übergeordnete Dienstgüteziele zu erfüllen: Mithilfe von Selbst-Management-Technologien wird zunächst eine Automatisierung des Dienstgüte-Managements auf Ebene einzelner Dienste erreicht. Die autonomen Management-Komponenten dieser Dienste können dann mithilfe von Selbstorganisationsmechanismen übergreifende Ziele zur Optimierung von Dienstgüteverhalten und Ressourcennutzung verfolgen. Für das SLM auf Ebene von SOA Workflows müssen temporär dienstübergreifende Kooperationen zur Erfüllung von Dienstgüteanforderungen etabliert werden, die sich damit auch über mehrere administrative Domänen erstrecken können. Eine solche zeitlich begrenzte Kooperation autonomer Teilsysteme kann sinnvoll nur dezentral erfolgen, da die jeweiligen Kooperationspartner im Vorfeld nicht bekannt sind und – je nach Lebensdauer einzelner Workflows – zur Laufzeit beteiligte Komponenten ausgetauscht werden können. In der Arbeit wird ein Verfahren zur Koordination autonomer Management-Komponenten mit dem Ziel der Optimierung von Antwortzeiten auf Workflow-Ebene entwickelt: Management-Komponenten können durch Übertragung von Antwortzeitanteilen untereinander ihre individuellen Ziele straffen oder lockern, ohne dass das Gesamtantwortzeitziel dadurch verändert wird. Die Übertragung von Antwortzeitanteilen wird mithilfe eines Auktionsverfahrens realisiert. Technische Grundlage der Kooperation bildet ein Gruppenkommunikationsmechanismus. Weiterhin werden in Bezug auf die Nutzung geteilter, virtualisierter Ressourcen konkurrierende Dienste entsprechend geschäftlicher Ziele priorisiert. Im Rahmen der praktischen Umsetzung wird die Realisierung zentraler Architekturelemente und der entwickelten Verfahren zur Selbstorganisation beispielhaft für das SLM konkreter Komponenten vorgestellt. Zur Untersuchung der Management-Kooperation in größeren Szenarien wird ein hybrider Simulationsansatz verwendet. Im Rahmen der Evaluation werden Untersuchungen zur Skalierbarkeit des Ansatzes durchgeführt. Schwerpunkt ist hierbei die Betrachtung eines Systems aus kooperierenden Management-Komponenten, insbesondere im Hinblick auf den Kommunikationsaufwand. Die Evaluation zeigt, dass ein dienstübergreifendes, autonomes Performance-Management in SOA-Umgebungen möglich ist. Die Ergebnisse legen nahe, dass der entwickelte Ansatz auch in großen Umgebungen erfolgreich angewendet werden kann.

Abbildung von XML-Dokumenten auf SQL:2003-konforme Datentypen

Die Auszeichnungssprache XML dient zur Annotation von Dokumenten und hat sich als Standard-Datenaustauschformat durchgesetzt. Dabei entsteht der Bedarf, XML-Dokumente nicht nur als reine Textdateien zu speichern und zu transferieren, sondern sie auch persistent in besser strukturierter Form abzulegen. Dies kann unter anderem in speziellen XML- oder relationalen Datenbanken geschehen. Relationale Datenbanken setzen dazu bisher auf zwei grundsätzlich verschiedene Verfahren: Die XML-Dokumente werden entweder unverändert als binäre oder Zeichenkettenobjekte gespeichert oder aber aufgespalten, sodass sie in herkömmlichen relationalen Tabellen normalisiert abgelegt werden können (so genanntes „Flachklopfen“ oder „Schreddern“ der hierarchischen Struktur). Diese Dissertation verfolgt einen neuen Ansatz, der einen Mittelweg zwischen den bisherigen Lösungen darstellt und die Möglichkeiten des weiterentwickelten SQL-Standards aufgreift. SQL:2003 definiert komplexe Struktur- und Kollektionstypen (Tupel, Felder, Listen, Mengen, Multimengen), die es erlauben, XML-Dokumente derart auf relationale Strukturen abzubilden, dass der hierarchische Aufbau erhalten bleibt. Dies bietet zwei Vorteile: Einerseits stehen bewährte Technologien, die aus dem Bereich der relationalen Datenbanken stammen, uneingeschränkt zur Verfügung. Andererseits lässt sich mit Hilfe der SQL:2003-Typen die inhärente Baumstruktur der XML-Dokumente bewahren, sodass es nicht erforderlich ist, diese im Bedarfsfall durch aufwendige Joins aus den meist normalisierten und auf mehrere Tabellen verteilten Tupeln zusammenzusetzen. In dieser Arbeit werden zunächst grundsätzliche Fragen zu passenden, effizienten Abbildungsformen von XML-Dokumenten auf SQL:2003-konforme Datentypen geklärt. Darauf aufbauend wird ein geeignetes, umkehrbares Umsetzungsverfahren entwickelt, das im Rahmen einer prototypischen Applikation implementiert und analysiert wird. Beim Entwurf des Abbildungsverfahrens wird besonderer Wert auf die Einsatzmöglichkeit in Verbindung mit einem existierenden, ausgereiften relationalen Datenbankmanagementsystem (DBMS) gelegt. Da die Unterstützung von SQL:2003 in den kommerziellen DBMS bisher nur unvollständig ist, muss untersucht werden, inwieweit sich die einzelnen Systeme für das zu implementierende Abbildungsverfahren eignen. Dabei stellt sich heraus, dass unter den betrachteten Produkten das DBMS IBM Informix die beste Unterstützung für komplexe Struktur- und Kollektionstypen bietet. Um die Leistungsfähigkeit des Verfahrens besser beurteilen zu können, nimmt die Arbeit Untersuchungen des nötigen Zeitbedarfs und des erforderlichen Arbeits- und Datenbankspeichers der Implementierung vor und bewertet die Ergebnisse.

Simultaneous Drying and Separation of Composite Agricultural Material for Hay Processing

In composite agricultural materials such as grass, tee, medicinal plants; leaves and stems have a different drying time. By this behavior, after leaving the dryer, the stems may have greater moisture content than desired, while the leaves one minor, which can cause either the appearance of fungi or the collapse of the over-dried material. Taking into account that a lot of grass is dehydrated in forced air dryers, especially rotary drum dryers, this research was developed in order to establish conditions enabling to make a separation of the components during the drying process in order to provide a homogeneous product at the end. For this, a rotary dryer consisting of three concentric cylinders and a circular sieve aligned with the more internal cylinder was proposed; so that, once material enters into the dryer in the area of the inner cylinder, stems pass through sieve to the middle and then continue towards the external cylinder, while the leaves continue by the inner cylinder. For this project, a mixture of Ryegrass and White Clover was used. The characteristics of the components of a mixture were: Drying Rate in thin layer and in rotation, Bulk density, Projected Area, Terminal velocity, weight/Area Ratio, Flux through Rotary sieve. Three drying temperatures; 40°C, 60° C and 80° C, and three rotation speeds; 10 rpm, 20 rpm and 40 rpm were evaluated. It was found that the differences in drying time are the less at 80 °C when the dryer rotates at 40 rpm. Above this speed, the material adheres to the walls of the dryer or sieve and does not flow. According to the measurements of terminal velocity of stems and leaves of the components of the mixture, the speed of the air should be less than 1.5 m s-1 in the inner drum for the leaves and less than 4.5 m s-1 in middle and outer drums for stems, in such way that only the rotational movement of the dryer moves the material and achieves a greater residence time. In other hand, the best rotary sieve separation efficiencies were achieved when the material is dry, but the results are good in all the moisture contents. The best rotary speed of sieve is within the critical rotational speed, i.e. 20 rpm. However, the rotational speed of the dryer, including the sieve in line with the inner cylinder should be 10 rpm or less in order to achieve the greatest residence times of the material inside the dryer and the best agitation through the use of lifting flights. With a finite element analysis of a dryer prototype, using an air flow allowing speeds of air already stated, I was found that the best performance occurs when, through a cover, air enters the dryer front of the Middle cylinder and when the inner cylinder is formed in its entirety through a sieve. This way, air flows in almost equal amounts by both the middle and external cylinders, while part of the air in the Middle cylinder passes through the sieve towards the inner cylinder. With this, leaves do not adhere to the sieve and flow along drier, thanks to the rotating movement of the drums and the showering caused by the lifting flights. In these conditions, the differences in drying time are reduced to 60 minutes, but the residence time is higher for the stems than for leaves, therefore the components of the mixture of grass run out of the dryer with the same desired moisture content.

Passive and Active Grasping with a Prehensile Robot End-Effector

This report presents a design of a new type of robot end-effector with inherent mechanical grasping capabilities. Concentrating on designing an end-effector to grasp a simple class of objects, cylindrical, allowed a design with only one degree of actuation. The key features of this design are high bandwidth response to forces, passive grasping capabilities, ease of control, and ability to wrap around objects with simple geometries providing form closure. A prototype of this mechanism was built to evaluate these features.

Maygen: A Symbolic Debugger Generation System

With the development of high-level languages for new computer architectures comes the need for appropriate debugging tools as well. One method for meeting this need would be to develop, from scratch, a symbolic debugger with the introduction of each new language implementation for any given architecture. This, however, seems to require unnecessary duplication of effort among developers. This paper describes Maygen, a "debugger generation system," designed to efficiently provide the desired language-dependent and architecture-dependent debuggers. A prototype of the Maygen system has been implemented and is able to handle the semantically different languages of C and OPAL.

Parallel Coupled Micro-Macro Actuators

This thesis presents a new actuator system consisting of a micro-actuator and a macro-actuator coupled in parallel via a compliant transmission. The system is called the Parallel Coupled Micro-Macro Actuator, or PaCMMA. In this system, the micro-actuator is capable of high bandwidth force control due to its low mass and direct-drive connection to the output shaft. The compliant transmission of the macro-actuator reduces the impedance (stiffness) at the output shaft and increases the dynamic range of force. Performance improvement over single actuator systems was expected in force control, impedance control, force distortion and reduction of transient impact forces. A set of quantitative measures is proposed and the actuator system is evaluated against them: Force Control Bandwidth, Position Bandwidth, Dynamic Range, Impact Force, Impedance ("Backdriveability'"), Force Distortion and Force Performance Space. Several theoretical performance limits are derived from the saturation limits of the system. A control law is proposed and control system performance is compared to the theoretical limits. A prototype testbed was built using permanenent magnet motors and an experimental comparison was performed between this actuator concept and two single actuator systems. The following performance was observed: Force bandwidth of 56Hz, Torque Dynamic Range of 800:1, Peak Torque of 1040mNm, Minimum Torque of 1.3mNm. Peak Impact Force was reduced by an order of magnitude. Distortion at small amplitudes was reduced substantially. Backdriven impedance was reduced by 2-3 orders of magnitude. This actuator system shows promise for manipulator design as well as psychophysical tests of human performance.

Design and Control of an Anthropomorphic Robotic Finger with Multi-point Tactile Sensation

The goal of this research is to develop the prototype of a tactile sensing platform for anthropomorphic manipulation research. We investigate this problem through the fabrication and simple control of a planar 2-DOF robotic finger inspired by anatomic consistency, self-containment, and adaptability. The robot is equipped with a tactile sensor array based on optical transducer technology whereby localized changes in light intensity within an illuminated foam substrate correspond to the distribution and magnitude of forces applied to the sensor surface plane. The integration of tactile perception is a key component in realizing robotic systems which organically interact with the world. Such natural behavior is characterized by compliant performance that can initiate internal, and respond to external, force application in a dynamic environment. However, most of the current manipulators that support some form of haptic feedback either solely derive proprioceptive sensation or only limit tactile sensors to the mechanical fingertips. These constraints are due to the technological challenges involved in high resolution, multi-point tactile perception. In this work, however, we take the opposite approach, emphasizing the role of full-finger tactile feedback in the refinement of manual capabilities. To this end, we propose and implement a control framework for sensorimotor coordination analogous to infant-level grasping and fixturing reflexes. This thesis details the mechanisms used to achieve these sensory, actuation, and control objectives, along with the design philosophies and biological influences behind them. The results of behavioral experiments with a simple tactilely-modulated control scheme are also described. The hope is to integrate the modular finger into an %engineered analog of the human hand with a complete haptic system.

Model-Based Matching by Linear Combinations of Prototypes

We describe a method for modeling object classes (such as faces) using 2D example images and an algorithm for matching a model to a novel image. The object class models are "learned'' from example images that we call prototypes. In addition to the images, the pixelwise correspondences between a reference prototype and each of the other prototypes must also be provided. Thus a model consists of a linear combination of prototypical shapes and textures. A stochastic gradient descent algorithm is used to match a model to a novel image by minimizing the error between the model and the novel image. Example models are shown as well as example matches to novel images. The robustness of the matching algorithm is also evaluated. The technique can be used for a number of applications including the computation of correspondence between novel images of a certain known class, object recognition, image synthesis and image compression.

Model-Based Matching of Line Drawings by Linear Combinations of Prototypes

We describe a technique for finding pixelwise correspondences between two images by using models of objects of the same class to guide the search. The object models are 'learned' from example images (also called prototypes) of an object class. The models consist of a linear combination ofsprototypes. The flow fields giving pixelwise correspondences between a base prototype and each of the other prototypes must be given. A novel image of an object of the same class is matched to a model by minimizing an error between the novel image and the current guess for the closest modelsimage. Currently, the algorithm applies to line drawings of objects. An extension to real grey level images is discussed.

Example Based Learning for View-Based Human Face Detection

We present an example-based learning approach for locating vertical frontal views of human faces in complex scenes. The technique models the distribution of human face patterns by means of a few view-based "face'' and "non-face'' prototype clusters. At each image location, the local pattern is matched against the distribution-based model, and a trained classifier determines, based on the local difference measurements, whether or not a human face exists at the current image location. We provide an analysis that helps identify the critical components of our system.