Active cooling of low-concentrating hybrid PV/Thermal collectors

A series of measurements on the performance of solar cell string modules with low-concentrating CPC reflectors with a concentration factor C ˜ 4X have been carried out. To minimise the reduction in efficiency due to high cell temperatures, the modules were cooled. Four different way of cooling were tested:1) The thermal mass of the module was increased, 2) passive air cooling was used by introducing a small air gap between the module and the reflector, 3) the PV cells were cooled by a large cooling fin, 4) the module was actively cooled by circulating cold water on the back. The best performance was given with the actively cooled PV module which gave 2,2 times the output from a reference module while for the output from the module with a cooling fin the value was 1,8.Active cooling is also interesting due to the possibility of co-generation of thermal and electrical energy which is discussed in the paper. Simulations, based on climate data from Stockholm, latitude 59.4°N, show that there are good prospects for producing useful temperatures of the cooling fluid with only a slightly reduced performance of the electrical fraction of the PV thermal hybrid system.

Cathepsin S as a biomarker of low-grade inflammation, insulin resistance, and cardiometabolic disease risk

Cathepsin S is a protease important in major histocompatibility complex (MHC) class II antigen presentation and also in degrading the extracellular matrix. Studies, most of them experimental, have shown that cathepsin S is involved in different pathological conditions such as obesity, inflammation, atherosclerosis, diabetes, and cancer.    The overall hypothesis of this report is that high levels of circulating cathepsin S, is a biomarker that reflects pathology induced by inflammation and obesity. The overall aim of this report was to investigate possible associations between circulating cathepsin S, inflammation, glucometabolic disturbance, and its associated diseases in the community. As cathepsin S appears to be a novel risk marker for several pathological conditions, we also wanted to examine the effect of dietary intervention on circulating cathepsin S concentrations.    This thesis is based on data from three community-based cohorts, the Uppsala longitudinal study of adult men (ULSAM), the prospective investigation of the vasculature in Uppsala seniors (PIVUS), and a post-hoc study from the randomized controlled NORDIET trial.    In the first study, we identified a cross-sectional positive association between serum cathepsin S and two markers of cytokine-mediated inflammation, CRP and IL-6. These associations were similar in non-obese individuals. In longitudinal analyses, higher cathepsin S at baseline was associated with higher CRP and IL-6 levels after six years of follow-up. In the second study, we identified a cross-sectional association between increased serum levels of cathepsin S and reduced insulin sensitivity. These associations were similar in non-obese individuals. No significant association was observed between cathepsin S and insulin secretion. In longitudinal analysis, higher cathepsin S levels were associated with an increased risk of developing diabetes during the six-year follow-up. In the third study, we found that higher serum levels of cathepsin S were associated with increased mortality risk. Moreover, in the ULSAM cohort, serum cathepsin S was independently associated with cause-specific mortality from cardiovascular disease and cancer. In the fourth study, we identified that adherence to an ad libitum healthy Nordic diet for 6 weeks slightly decreased the levels of plasma cathepsin S in normal or marginally overweight individuals, relative to the control group. Changes in circulating cathepsin S concentrations were correlated with changes in body weight, LDL-C, and total cholesterol.    Conclusion: This thesis shows that circulating cathepsin S is a biomarker that independently reflects inflammation, insulin resistance, the risk of developing diabetes, and mortality risk. Furthermore, a Nordic diet moderately reduced cathepsin S levels in normal-weight and overweight men and women. This effect may be partially mediated by diet-induced weight loss and possibly by reduced LDL-C concentrations. 

Why do women of low socioeconomic status have poorer dietary behaviours than women of higher socioeconomic status? A qualitative exploration

In developed countries, persons of low socioeconomic status (SES) are generally less likely to consume diets consistent with dietary guidelines. Little is known about the mechanisms that underlie SES differences in eating behaviours. Since women are often responsible for dietary choices within households, this qualitative study investigated factors that may contribute to socioeconomic inequalities in dietary behaviour among women. Semi-structured interviews were conducted with 19 high-, 19 mid- and 18 low- SES women, recruited from Melbourne, Australia, using an area-level indicator of SES. An ecological framework, in which individual, social and environmental level influences on diet were considered, was used to guide the development of interview questions and interpretation of the data. Thematic analysis was undertaken to identify the main themes emerging from the data. Several key influences varied by SES. These included food-related values such as health consciousness, and a lack of time due to family commitments (more salient among higher SES women), as well as perceived high cost of healthy eating and lack of time due to work commitments (more important for low SES women). Reported availability of and access to good quality healthy foods did not differ strikingly across SES groups. Public health strategies aimed at reducing SES inequalities in diet might focus on promoting healthy diets that are low cost, as well as promoting time-efficient food preparation strategies for all women.

Safety of low-carbohydrate diets

Low-carbohydrate diets have re-emerged into the public spotlight and are enjoying a high degree of popularity as people search for a solution to the population's ever-expanding waistline. The current evidence though indicates that low-carbohydrate diets present no significant advantage over more traditional energy-restricted diets on long-term weight loss and maintenance. Furthermore, a higher rate of adverse side-effects can be attributed to low-carbohydrate dieting approaches. Short-term efficacy of low-carbohydrate diets has been demonstrated for some lipid parameters of cardiovascular risk and measures of glucose control and insulin sensitivity, but no studies have ascertained if these effects represent a change in primary outcome measures. Low-carbohydrate diets are likely effective and not harmful in the short term and may have therapeutic benefits for weight-related chronic diseases although weight loss on such a program should be undertaken under medical supervision. While new commercial incarnations of the low-carbohydrate diet are now addressing overall dietary adequacy by encouraging plenty of high-fibre vegetables, fruit, low-glycaemic-index carbohydrates and healthier fat sources, this is not the message that reaches the entire public nor is it the type of diet adopted by many people outside of the world of a well-designed clinical trial. Health effects of long-term ad hoc restriction of inherently beneficial food groups without a concomitant reduction in body weight remains unanswered.

The mechanical characterization of low work hardening, high strength steel

One of the major challenges in assessing the mechanical properties of recovery annealed steel is the strain localization that occurs almost immediately on the formation of the first Lüders band, such that no or limited propagation of the Lüders band occurs along the tensile coupon. The stress raiser associated with the geometry of the standard tensile coupon means that this plastic deformation is often completely outside the standard extensometers on the coupon. Hence, no strain is measured during the test. While this is not important for assessing the tensile strength of the steel, it does mean that the strain related properties, such as the elastic limit of the steel, cannot be measured using standard testing techniques.This work addresses this issue by examining three techniques for ensuring that the strain occurs inside the extensometer. It is shown that the best technique is the extended extensometer, where the gauge length covers slightly more than the tensile coupon parallel length. While this leads to some variation in the width of the material being measured, compensation can be be made by adjusting the strain to correct the Young's Modulus.This technique has direct implications not just for recovery annealed steels, but for other high strength, low work hardening materials such as ultrafine ferrite. A particular requirement of these high strength steels in structural applications is a high elastic limit; hence, measurement of the strain related properties for these high strength materials must be considered vital in their mechanical assessment.

An experimental study of low velocity impact response in 2/2 twill weave composite laminates manufactured by a novel fabrication process

A novel fabrication process for advanced composite components—the QuicktepTM process was described. 2/2 twill weave MTM56/CF0300 carbon epoxy composite laminates were manufactured by the Quickstep and the autoclave processes. The response of these laminates to drop-weight low velocity impact at energy levels ranging from 5 to 30 J was investigated. It was found that the laminates fabricated by the Quickstep had better impact damage tolerance than those fabricated by the autoclave. Optical microscopy revealed extensive matrix fracture in the center of the backside of the autoclave laminates indicating the more brittle property of the epoxy matrix cured by the autoclave process. Interfacial shear strength (IFSS) for two composite systems were measured by micro–debond experiments. The MTM56/CF0300 material cured by the Quickstep showed stronger fibre matrix adhesion. Since the thickness and density of the impact targets produced by two processes were different, finite element analysis (FEA) was performed to study the effect of these factors on the impact response. The simulation results showed that the difference in thickness and density affects the stress distribution under impact loading. Higher thickness and lower density caused by processing lead to less endurance to drop weight impact loading. Therefore the better performance of Quickstep laminates under impact loading was not due to the thickness and density change, but resulted from stronger mechanical properties.

Acute exercise and GLUT4 expression in human skeletal muscle: influence of exercise intensity

To examine the influence of exercise intensity on the increases in vastus lateralis GLUT4 mRNA and protein after exercise, six untrained men exercised for 60 min at 39 ± 3% peak oxygen consumption (VO2 peak) (Lo) or 27 ± 2 min at 83 ± 2% VO2 peak (Hi) in counterbalanced order. Preexercise muscle glycogen levels were not different between trials (Lo: 408 ± 35 mmol/kg dry mass; Hi: 420 ± 43 mmol/kg dry mass); however, postexercise levels were lower (P < 0.05) in Hi (169 ± 18 mmol/kg dry mass) compared with Lo (262 ± 35 mmol/kg dry mass). Thus calculated muscle glycogen utilization was greater (P < 0.05) in Hi (251 ± 24 mmol/kg) than in Lo (146 ± 34). Exercise resulted in similar increases in GLUT4 gene expression in both trials. GLUT4 mRNA was increased immediately at the end of exercise (~2-fold; P < 0.05) and remained elevated after 3 h of postexercise recovery. When measured 3 h after exercise, total crude membrane GLUT4 protein levels were 106% higher in Lo (3.3 ± 0.7 vs. 1.6 ± 0.3 arbitrary units) and 61% higher in Hi (2.9 ± 0.5 vs. 1.8 ± 0.5 arbitrary units) relative to preexercise levels. A main effect for exercise was observed, with no significant differences between trials. In conclusion, exercise at ~40 and ~80% VO2 peak, with total work equal, increased GLUT4 mRNA and GLUT4 protein in human skeletal muscle to a similar extent, despite differences in exercise intensity and duration.

Reliability of moderate-intensity and vigorous physical activity stage of change measures for young adults.

Background
The purpose of this study was to examine the reliability of stage of change (SOC) measures for moderate-intensity and vigorous physical activity in two separate samples of young adults. Staging measures have focused on vigorous exercise, but current public health guidelines emphasize moderate-intensity activity.
Method
For college students in the USA (n = 105) and in Australia (n = 123), SOC was assessed separately on two occasions for moderate-intensity activity and for vigorous activity. Test–retest repeatability was determined, using Cohen’s kappa coefficient.
Results
In both samples, the reliability scores for the moderate-intensity physical activity staging measure were lower than the scores for the vigorous exercise staging measure. Weighted kappa values for the moderate-intensity staging measure were in the “fair to good” range for both studies (0.50 and 0.45); for the vigorous staging measure kappa values were “excellent” and “fair to good” (0.76 and 0.72).
Conclusions
There is a need to standardize and improve methods for staging moderate-intensity activity, given that such measures are used in public health interventions targeting HEPA (health-enhancing physical activity).

Consumer acceptability of low fat foods containing inulin and oligofructose

Inulin and oligofructose were used as fat replacers in Anzac cookies, blueberry muffins, carrot cake, chocolate cake, lemon cheesecake, ice cream, and beef sausages at levels ranging from 4 to 13g/100g, achieving a significant reduction in fat content (20% to 80% relative). These foods were rated as acceptable by an untrained taste panel, but scored consistently lower than their full-fat counterparts (controls). Regression analysis showed that, unlike the controls, texture was more important than flavor in determining overall acceptability of the low-fat foods. Inulin and oligofructose are readily incorporated into bakery and meat formulations, but their use might be limited by adverse physiological effects when consumed at high levels.

Development of low cost motion-sensing system

Micro-electro-mechanical system (MEMS) technology offers sensors with lower cost, smaller size, lower power consumption. In this paper, a kind of low cost motion-sensing system based MEMS sensors is developed. The objective of the design is low cost, small volume and light weight in order to be used in many fields. The constituting principle of the system is described. Algorithms and hardware of the system are researched. And the definition of coordinate, calculation of pose angle, transform of acceleration and calculation of the velocities and displacement of the moving object are presented with corresponding mathematics model and algorithms. The experiments are carried out in principle and results are given. It is proved that the low cost motion-sensing system is effective and correct.

Leontief paradox and the role of factor intensity measurement

In contrast with the prediction of the Heckscher-Ohlin (HO) theorem, Leontief (1953) found that the capital-labor ratio embodied in the US exports is smaller than the capital-labor ratio embodied in the US competitive import replacements. In Leontief's analysis, the measured factor content of US imports is computed based on the assumption that all countries are using the US factor intensity techniques. This paper relaxes all assumption of identical factor intensity techniques. It uses an inferring method to infer the factor intensity techniques of different countries based on international relative factor price differences. With the inferred differentiated factor intensity techniques , the Leontief paradox is re-investigated and is found to be either disappeared or eased.

Effect of low-dose mobile versus traditional epidural techniques on mode of delivery: a randomised controlled trial

Background

Epidural analgesia is the most effective labour pain relief but is associated with increased rates of instrumental vaginal delivery and other effects, which might be related to the poor motor function associated with traditional epidural. New techniques that preserve motor function could reduce obstetric intervention. We did a randomised controlled trial to compare low-dose combined spinal epidural and low-dose infusion (mobile) techniques with traditional epidural technique.
Methods

Between Feb 1, 1999, and April 30, 2000, we randomly assigned 1054 nulliparous women requesting epidural pain relief to traditional (n=353), low-dose combined spinal epidural (n=351), or low-dose infusion epidural (n=350). Primary outcome was mode of delivery, and secondary outcomes were progress of labour, efficacy of procedure, and effect on neonates. We obtained data during labour and interviewed women postnatally.
Findings

The normal vaginal delivery rate was 35·1% in the traditional epidural group, 42·7% in the low-dose combined spinal group (odds ratio 1·38 [95% CI 1·01–1·89]; p=0·04); and 42·9% in the low-dose infusion group (1·39 [1·01–1·90]; p=0·04). These differences were accounted for by a reduction in instrumental vaginal delivery. Overall, 5 min APGAR scores of 7 or less were more frequent with low-dose technique. High-level resuscitation was more frequent in the low-dose infusion group.

Influence of low-strain deformation characteristics of high strength sheet steel on curl and springback in bend-under-tension tests

The influence of low-strain deformation behavior on curl and springback in advanced high strength steels (AHSS) was assessed using a bend-under-tension test. The effect of yielding behavior on curl and springback was examined by heat-treating two dual-phase steels to induce yield point elongation, while keeping a relatively constant tensile strength and a constant sheet thickness. A dual-phase and TRIP steel with similar initial thickness and tensile strengths were also examined to investigate the effect of work-hardening on curl and springback. It is shown that while current understanding limits prediction of curl and springback in bending under tension using only the initial sheet thickness and tensile strength, both the yielding and work-hardening behavior can affect the results. Explanations for these effects are proposed in terms of the discontinuous yielding and flow stress in the materials.

Effects of low dosage pyrene pollution on biochemical characters of earthworm (Eisenia fetida) in soil

By the method of artificial soil pollution, an exposure experiment with different concentrations of pyrene (0, 60, 120, 240, 480, 960 microg x kg(-1)) was conducted to determine the cytochrome P450 and MDA contents and the glutathione-S-transferase (GST), superoxide dismutase (SOD), peroxidase (POD) and catalase (CAT) activities in earthworm gut after exposure for 1, 3, 7 and 14 days. The results indicated that within the range of test pyrene concentrations, all the biochemical indices tested differed in their sensitivity to pyrene toxicity, among which, P450 content and GST and SOD activities were most sensitive, followed by POD and CAT activities, while MDA content did not show any obvious response. Exposure duration had stronger effects than exposure dosage. In diagnosing the ecotoxicity of soil pollutant, it could be necessary to use a combined multi-time and multi-index diagnostic method to enhance the sensitivity and effectiveness of the indices adopted.

2001 Volvo Award winner in clinical studies : effects of a media campaign on back pain beliefs and its potential influence on management of low back pain in general practice

Study Design. Quasi-experimental, nonrandomized, nonequivalent, parallel group-controlled study involving before and after telephone surveys of the general population and postal surveys of general practitioners was conducted, with an adjacent state used as a control group.


Objectives. To evaluate the effectiveness of a population-based intervention designed to alter beliefs about back pain, influence medical management, and reduce disability and workers’ compensation–related costs.


Summary of Background Data. A multimedia campaign begun during 1997 in Victoria, Australia, positively advised patients with back pain to stay active and exercise, not to rest for prolonged periods, and to remain at work.


Methods. The campaign’s impact on population beliefs about back pain and fear-avoidance beliefs was measured in telephone surveys, and the effect of the campaign on the potential management of low back pain by general practitioners was assessed by eliciting their likely approach to two hypothetical scenarios in mailed surveys. Demographically identical population groups in Victoria and the control state, New South Wales, were surveyed at three times: before, during, and after intervention in Victoria.


Results. The studies were completed by 4730 individuals in the general population and 2556 general practitioners. There were large statistically significant improvements in back pain beliefs over time in Victoria (mean scores on the Back Beliefs Questionnaire, 26.5, 28.4, and 29.7), but not in New South Wales (26.3, 26.2, and 26.3, respectively). Among those who reported back pain during the previous year, fear-avoidance beliefs about physical activity improved significantly in Victoria (mean scores on the Fear-Avoidance Beliefs Questionnaire for physical activity, 14, 12.5, and 11.6), but not in New South Wales (13.3, 13.6, and 12.7, respectively). General practitioners in Victoria reported significant improvements over time in beliefs about back pain management, as compared with their interstate colleagues. There were statistically significant interactions between state and time for 7 of 10 responses on management of acute low back pain, and for 6 of 10 responses on management of subacute low back pain.


Conclusion. A population-based strategy of providing positive messages about back pain improves the beliefs of the general population and general practitioners about back pain and appears to influence medical management.