Effects of furanace on Brachionus

Tiger prawn P.monodon) larvae utilize Brachionus a rotifer, as food in the Zoea 3 and mysis stages when they change from an herbivorous to an omnivorous diet. The present work aims to show the effects of furanace on the population growth of Brachionus. Cultures of Brachionus were obtained and fed with Chlorella at a density of 1-2x10 SUP-6 cells/ml. Five liters of the culture water were placed in each of 4 white, circular, 152x304 mm plastic basins. The mean initial densities of the rotifer ranged from 26 . 5 to 38 . 5 individuals/ml. The concentrations of furanace were 0, 1, 2 and 3 mg /l. The cultures were vigorously aerated. Population growth was observed after 3, 6, and 9 hours of exposure. The cultures were thoroughly mixed before samples were taken to ensure an almost equal distribution of the rotifers in the water. To facilitate the counting of the rotifer, one drop of Lugol's solution was added to each sample. This immobilizes the rotifer as well as stops further reproduction. Individuals with only the lorica left or with badly deformed lorica were considered dead. Population counts were done using a Sedgwick-Rafter counting chamber. Among the different durations of exposure, the percentage survival of the populations in the furanace baths were highest after 3 hr. There were slight increases in the control and 2 mg/l and slight decreases in 1 and 3 mg/l. The differences in the mean densities are statistically insignificant at . 01 significance level. After a 6-hr exposure, the control population reached its peak density with a survival of 89%. Populations in furanace baths decreased to 88 . 5% in both 2 and 3 mg /l followed closely by 87% in 1 mg/l. Again, no statistical differences exist among all the levels. The mean percentage survival in 1 and 2 mg/l increased (89% and 91%, respectively) after a 9-hr expsoure, while those in the control and 3 mg/l decreased to 86 . 5% and 88 . 25%, respectively. There were no marked differences in appearance noted among the individuals in furanace baths and those in the control.

Fishing gear selectivity of Lates niloticus L. (Nile perch), Oreochromis niloticus L. (Nile tilapia) and Rastrineobola argentea Pellegrin (Mukene) in lakes Victoria, Kyoga and Nabugabo

Catch effort data on which fisheries management regulations are sometimes based are not available for most lakes in Uganda. However, failure to regulate fishing gears and methods has been a major cause of collapse of fisheries in the country. Fisheries have been damaged by destructive and non-selective fishing gears and methods such as trawling and beach seining, by use of gill nets of mesh size which crop immature fish and by introduction of mechanised fishing. Selectivity of the gears used to crop Lates niloticus 1. (Nile perch), Oreochromis niloticus 1. (Nile tilapia) and Rastrineobola argentea (Mukene) which are currently the most important commercial species in Uganda were examined in order to recommend the most suitable types, sizes and methods that should be used in exploiting these fisheries . Gill nets of less than 127 mm mainly cropped immature Nile ti1apia and Nile perch. To protect these fisheries, the minimum mesh size of gill nets should be set at 127 mm. Seine nets of 5 mm do catch high proportions of immature Mukene while those of 10 mm catch mainly mature Mukene. When operated inshore, both sizes catch immature Nile perch and Nile ti1apia as by-catch. To protect the Mukene fishery and avoid catching immature byecatch, a minimum mesh size of the Mukene net should have been 10 mm operated as Lampara type net offshore but since most fishennen have been using the 5 mm seine for over five years the minimum size should not be allowed to drop below 5 mm pending further thorough investigations. Beach seining, trawling and are destructive to fisheries and should be prohibited until data that may justify their use is available.

Imbibition dynamics of nano-particulate ink-jet drops on micro-porous media

Ink-jet printing of nano-metallic colloidal fluids on to porous media such as coated papers has become a viable method to produce conductive tracks for low-cost, disposable printed electronic devices. However, the formation of well-defined and functional tracks on an absorbing surface is controlled by the drop imbibition dynamics in addition to the well-studied post-impact drop spreading behavior. This study represents the first investigation of the real-time imbibition of ink-jet deposited nano-Cu colloid drops on to coated paper substrates. In addition, the same ink was deposited on to a non-porous polymer surface as a control substrate. By using high-speed video imaging to capture the deposition of ink-jet drops, the time-scales of drop spreading and imbibition were quantified and compared with model predictions. The influences of the coating pore size on the bulk absorption rate and nano-Cu particle distribution have also been studied.

A study on stock enhancement/restocking of the Kyoga basin lakes

Increased management attention to the fisheries tn Uganda is fuelled by five major factors:socio-economic demands, human population increase,stock depletion, biodiversity loss and,environmental degradation.Fish exports from Uganda to overseas and regional markets have rapidly increased since the mid 1990s and it is estimated that total exports are worth at least US$ 200m three quarters of the value due mostly to Nile perch exports to overseas markets.Exports to regional markets are dominated by variously processed tilapia "mukene" (Rastrineobo/a argentea),Nile perch "angara"(A/estes baremose) and cat fishes.Virtually all major water bodies contribute to this trade. A combinatilm of exports and an increased human population has seen the per capita fish consumption in Uganda drop from 15kg in the early 1990s to almost 10kg by 2005.this figure is below the WHO recommended fish protein intake of 17kg. the apparent fish gap in a liberalised economic framework has stimulated interest in commercial fish farming

Switching characteristics of diamond-based m-i-p+ diodes in power electronic applications

Modeling and numerical analysis of diamond m-i-p+ diode have been performed for static and transient analysis using TCAD Sentaurus platform. The simulation results are compared with experimental measurements. Prediction of transient turn-off characteristics of diamond m-i-p+ diode at high temperature is performed for the first time. It was found that unlike conventional Si diode, peak reverse current in diamond m-i-p+ diode reduces with increasing temperature while on-state voltage drop increases. © 2011 IEEE.

Hardfacing using supersonic laser depostion of stellite-6

The capability of manufacturing coatings is of central importance in engineering design. Many components require nowadays the application of additional layers, to enhance mechanical properties and protect against hostile environments. Supersonic Laser Deposition (SLD) is a novel coating method, based upon Cold Spray (CS) principles. In this technique the deposition velocities can be significantly lower than those required for effective bonding in CS applications. The addition of laser heat energy permits a change in the thermodynamic experience of impacting particles, thereby offering a greater opportunity for metallurgical bonding at lower velocities compared to the CS process technology. The work reported in this paper demonstrates the ability of the SLD process to deliver hard facing materials to engineering surfaces. Stellite-6 has been deposited on low carbon steel tubes over a range of process parameters, determining the appropriate target power and traverse speeds for coating deposition. Coating properties and parameters were examined to determine the main properties, micro-structure and processing cost. Their morphology was studied through optical microscopy, SEM and X-Ray Diffraction. The results have shown that SLD is capable of depositing Stellite-6, with enhanced properties compared to laser clad counterparts.

Permeability and stiffness of sands at very low effective stresses

Loose saturated sandy soils may undergo liquefaction under cyclic loading, generating positive excess pore pressures due to their contractile nature and inability to dissipate pore pressures rapidly during earthquake loading. These liquefied soils have a near-zero effective stress state, and hence have very low strength and stiffness, causing severe damage to structures founded upon them. The duration for which this near-zero effective stress state persists is a function of the rate of reconsolidation of the liquefied soil, which in turn is a function of the permeability and stiffness of the soil at this very low effective stress. Existing literature based on observation of physical model tests suggests that the consolidation coefficient C v associated with this reconsolidation of liquefied sand is significantly lower than that of the same soil at moderate stress levels. In this paper, the results of a series of novel fluidisation tests in which permeability k and coefficient of consolidation C v were independently measured will be presented. These results allow calculation of the variation of stiffness E 0 and permeability k with effective stress. It is shown that while permeability increases markedly at very low effective stresses, the simultaneous drop in stiffness measured results in a decrease in consolidation coefficient and hence an increase in the duration for which the soil remains liquefied.

Discrete element calculations of the impact of a sand column against rigid structures

Discrete particle simulations of column of an aggregate of identical particles impacting a rigid, fixed target and a rigid, movable target are presented with the aim to understand the interaction of an aggregate of particles upon a structure. In most cases the column of particles is constrained against lateral expansion. The pressure exerted by the particles upon the fixed target (and the momentum transferred) is independent of the co-efficient of restitution and friction co-efficient between the particles but are strongly dependent upon the relative density of the particles in the column. There is a mild dependence on the contact stiffness between the particles which controls the elastic deformation of the densified aggregate of particles. In contrast, the momentum transfer to a movable target is strongly sensitive to the mass ratio of column to target. The impact event can be viewed as an inelastic collision between the sand column and the target with an effective co-efficient of restitution between 0 and 0.35 depending upon the relative density of the column. We present a foam analogy where impact of the aggregate of particles can be modelled by the impact of an equivalent foam projectile. The calculations on the equivalent projectile are significantly less intensive computationally and yet give predictions to within 5% of the full discrete particle calculations. They also suggest that "model" materials can be used to simulate the loading by an aggregate of particles within a laboratory setting. © 2012 Elsevier Ltd. All rights reserved.

Advanced applications of a computational design synthesis method

From modelling to manufacturing, computers have increasingly become partners in the design process, helping automate many phases once carried out by hand. In the creative phase, computational synthesis methods aim at facilitating designers' task through the automated generation of optimally directed design alternatives. Nevertheless, applications of these techniques are mainly academic and industrial design practice is still far from applying them routinely. This is due to the complex nature of many design tasks and to the difficulty of developing synthesis methods that can be easily adapted to multiple case studies and automated simulation. This work stems from the analysis of implementation issues and obstacles to the widespread use of these tools. The research investigates the possibility to remove these obstacles through the application of a novel technique to complex design tasks. The ability of this technique to scale-up without sacrificing accuracy is demonstrated. The successful results confirm the possibility to use synthesis methods in complex design tasks and spread their commercial and industrial application.

A framework for designing product service systems

In this competitive globalizing scenario, manufacturers are adopting a strategy of bundling products and services into an integrated solution to create sustainable competitive advantage. Servitizing manufacturers are increasingly transforming their processes and practices to build product-service systems (PSS). During this transformation they require substantial support to face stringent challenges. Research in the PSS domain is heading towards the development of a design theory and methodology that facilitates the systematic creation of viable PSS conceptual designs. In this paper, various proposed design methods are reviewed and research gaps are summarized. Primarily, it has been observed that the importance of the capabilities of the stakeholders involved in designing PSS has not been noted in the proposed methods. Regarding this capability view point, a framework for designing PSS has been proposed. This framework highlights the important features required in designing PSS such as co-creation, responsibilities and competences. Every step in the framework has been explained with a case study involving laser systems used for manufacturing cutting operation.

On the functions of products

Understanding the performance and manner of functioning of existing products is at the base of new product development activities. In engineering design the term function is generally used to refer to the technical actions performed by a product. However, products accomplish a wider range of goals. This research explores the opportunity to describe and model, through the concept of function, product actions across four dimensions including technical, aesthetic, social and economic. The research demonstrates that non-technical functions can be represented through active verbs and nouns and modelled using a method known as the Function Analysis Diagram (FAD). The research argues that when technical, aesthetic, social and economic perspectives on product development are considered as different types of function, stakeholders have a common language to communicate which can benefit design collaboration.

Use of automatic sand pourers for loose sand models

The consistency of laboratory sand model preparation for physical testing is a fundamental criterion in representing identical geotechnical issues at prototype scale. This objective led to the development of robotic apparatus to eliminate the non-uniformity in manual pouring. Previous studies have shown consistent sand models with high relative density between 50 to 90% produced by the automatic moving-hopper sand pourer at the University of Cambridge, based primarily on a linear correlation to flow rate. However, in the case of loose samples, the influence of other parameters, particularly the drop height, becomes more apparent. In this paper, findings on the effect of flow rate and drop height are discussed in relation to the layer thickness and relative density of loose sand samples. Design charts are presented to illustrate their relationships. The effect of these factors on different sand types is also covered to extend the use of the equipment. © 2010 Taylor & Francis Group, London.

The analysis of impact forces in randomly vibrating elastic systems

This work is concerned with the characteristics of the impact force produced when two randomly vibrating elastic bodies collide with each other, or when a single randomly vibrating elastic body collides with a stop. The impact condition includes a non-linear spring, which may represent, for example, a Hertzian contact, and in the case of a single body, closed form approximate expressions are derived for the duration and magnitude of the impact force and for the maximum deceleration at the impact point. For the case of two impacting bodies, a set of algebraic equations are derived which can be solved numerically to yield the quantities of interest. The approach is applied to a beam impacting a stop, a plate impacting a stop, and to two impacting beams, and in each case a comparison is made with detailed numerical simulations. Aspects of the statistics of impact velocity are also considered, including the probability that the impact velocity will exceed a specified value within a certain time. © 2012 Elsevier Ltd. All rights reserved.

2D PIV measurements in the near field of grid turbulence using stitched fields from multiple cameras

We present measurements of grid turbulence using 2D particle image velocimetry taken immediately downstream from the grid at a Reynolds number of Re M = 16500 where M is the rod spacing. A long field of view of 14M x 4M in the down- and cross-stream directions was achieved by stitching multiple cameras together. Two uniform biplanar grids were selected to have the same M and pressure drop but different rod diameter D and crosssection. A large data set (10 4 vector fields) was obtained to ensure good convergence of second-order statistics. Estimations of the dissipation rate ε of turbulent kinetic energy (TKE) were found to be sensitive to the number of meansquared velocity gradient terms included and not whether the turbulence was assumed to adhere to isotropy or axisymmetry. The resolution dependency of different turbulence statistics was assessed with a procedure that does not rely on the dissipation scale η. The streamwise evolution of the TKE components and ε was found to collapse across grids when the rod diameter was included in the normalisation. We argue that this should be the case between all regular grids when the other relevant dimensionless quantities are matched and the flow has become homogeneous across the stream. Two-point space correlation functions at x/M = 1 show evidence of complex wake interactions which exhibit a strong Reynolds number dependence. However, these changes in initial conditions disappear indicating rapid cross-stream homogenisation. On the other hand, isotropy was, as expected, not found to be established by x/M = 12 for any case studied. © Springer-Verlag 2012.