Calibração da Reflectometria no Domínio do Tempo (TDR) para a estimativa da concentração da solução no solo

Time Domain Reflectometry (TDR) is a reliable method for in-situ measurements of the humidity and the solution concentration at the same soil volume. Accurate interpretation of electrical conductivity (and soil humidity) measurements may require a specific calibration curve. The primary goal of this work was to establish a calibration procedure for using TDR to estimate potassium nitrate concentrations (KNO3) in soil solution. An equation relating the electrical conductivity measured by TDR and KNO3 concentration was established enabling the use of TDR technique to estimate soil water content and nitrate concentration for efficient fertigation management.

Colheita de cana-de-açúcar com auxílio mecânico

Civil society and sugarcane farmer demands indicate that harvesting technology has enough limitations to jeopardize production in large sugar cane producing areas. This work analyses the current mechanical harvesting compared to a semi-mechanical harvesting proposal, on the bases of eleven characteristics considered determinant for a quick spreading of green cane harvesting on hilly areas, with lower impact on agricultural labor and farmers investment capacity.

Avaliação física do tomate de mesa 'Romana' durante manuseio na pós-colheita

Tomato postharvest losses are very high in Brazil and the goal of this research was to evaluate the effect of handling and the transport of tomato fruits, cultivar Romana on the steps of harvesting, weight and transportation to the packinghouse, pointing some critical points. Tomatoes were harvested at plastic boxes, weighted and shipped to a packinghouse. Fruits taken directly from the plant were determined as reference. The parameters evaluated were weight loss and mechanical injury and tomato physical quality after storage during 21 days. It was observed an increasing on the weight loss, external damage, and postharvest losses, after storage. Handling and transportation were the cause of an increase in 6.6% in external damage and 1.93% of weight loss after storage, when comparing harvested fruits and fruits evaluated on the packing-house. The main reason for postharvest losses was due to mechanical injury caused during transportation mainly due to the compressure force among fruits and against the plastic boxes.

Equipamento microprocessado para geração de sinal de correção diferencial, em tempo real, para GPS

This work presents the development of low cost microprocessor-based equipment for generation of differential GPS correction signal, in real time, and configuration and supervision of the GPS base. The developed equipment contains a dedicated microcontroller connected to the GPS receiver, alphanumeric display and multifunction keyboard for configuration and operation of the system and communication interfaces. The electronic circuit has the function of receiving the information from GPS base; interpret them, converting the sentence in the RTCM SC-104 protocol. The microcontroller software makes the conversion of the signal received by the GPS base from the specific format to RTCM SC-104 protocol. The processing main board has two serials RS-232C standard interfaces. One of them is used for configuration and receiving the information generated by the GPS base. The other operates as output, sending the differential correction signal for the transmission system. The development of microprocessor-based equipment showed that it is possible the construction of a low cost private station for real time generation of differential GPS correction signal.

Influência do auxílio mecânico na colheita de tomates

Fresh tomato harvest is traditionally made without harvesting aids. The main goal of this research was to evaluate performance parameters of fresh tomato harvesting aid equipment and compare it to traditional harvest, in the state of São Paulo. Therefore, an equipment was developed and the harvest process was evaluated in four different ways: traditional system (harvest system used in Santa Luzia farm, Brotas, SP, Brazil), picker walking with a harvesting aid equipment, picker seated in a harvesting aid equipment and a composition of both systems: two pickers seated and one picker walking in two different velocities ranges. The different systems using harvesting aid showed an average yield by picker more efficient than reference. Harvest system using three pickers showed an increase of 290% on yield average by picker, on the range of 0.5-1.0 fruit per plant, followed by the systems with a walking picker, that increased productivity in 41%, and picker seated harvester, that showed an increase of 35%. These results demonstrate the importance of using a harvesting aid equipment.

Avaliação de perdas invisíveis na colheita mecanizada em dois fluxos de massa de cana-de-açúcar

In this work the performance of a sugar cane chopped harvester was analysed when fed with two sugar cane mass flows, measuring the invisible losses, which are impossible to measure in the field, harvester sugar cane cleaning efficiency and air velocity on extractors exit. The trial was done under controlled conditions at Copersucar Technology Center in January 2000. The results showed that the flow of sugar cane through the harvester doesn't influence the magnitudes of total invisible losses and raw material cleaning efficiency. The mean air velocity on the primary extractors exit was 12.0 m s-1, and 9.2 m s-1 on the secondary extractor, with a coefficient of variation of 21%, indicating that the poor cleaning performance of the harvester could be related to air velocity difference inside the extractor. Analyzing the data collected in the trials, it was possible to conclude that invisible losses in sugar cane harvester were 10% and the cleaning efficiency was 87%.

Transferência de massa e secagem em leitos vibrofluidizados: uma revisão

Development of processing technology and equipments requires new methods and better quality of the processed product. In the continuous drying process, utilization of equipments that promotes an increment in the transfer coefficients becomes of the major interest. The use of vibrational energy has been recommended to the dispersed materials. Such method is based on the use of vibrational energy applied to disperse media. Thus, a literature review on the mass transfer and drying in vibro-fluidized beds was carried out, showing experimental results and mathematical modeling.

Aerodinâmica de leitos vibrofluidizados: uma revisão

Application of mechanical vibration to aid fluidization and to improve heat, mass and momentum transfer are usual processes in agricultural industry and it has found nowadays extensive applications in particle processing of materials difficult-to-fluidized. Equations and experimental data found in literature for the aerodynamics characteristics of vibro-fluidized beds are presented and discussed, emphasizing the vibration effect in the bed.

Ambiência aérea em alojamento de frangos de corte: poeira e gases

Air quality in animal production environment has been refereed as an interesting point for studies in environmental control systems with the focus both to the animal health which live in total confinement, as to the workers. The objective of this research was to determine the variation on the aerial environmental quality in two types of broiler housing: conventional (Gc) and tunnel type (Gt). The total dust values in both houses offered adequate rearing conditions to the birds; however, regarding the inhale dust in the air was above the limits recommended for humans. Carbon monoxide concentration in the heating phase during the evaluated period was above the 10 ppm maximum recommended, and it was higher during the cold season in Gt house (30 ppm) when compared to the Gc house (18 ppm). Ammonia concentration peaks in the air were above the 20 ppm recommended from the 20th day of production in both houses and in daily average, for a period higher in Gt (4h30) when compared to Gt (2h45). Only traces of nitrate oxide and methane were found while carbonic dioxide gas concentration evaluated during daytime met the limits allowed for both birds and labor.

Qualidade da classificação do tomate de mesa em unidades de beneficiamento

Quality evaluation of classification was done in two fresh market tomatoes packing house, using electronically and mechanical equipments in two harvest periods, summer and winter seasons. The main goal of this work was to evaluate size and color grading conformity with the standards proposed by the Brazilian Program for Horticulture Modernization and size grading obtainded with the one established by the packer. The cultivar studied was Carmen. The results showed that there was no grade conformity with the fresh tomato quality standards proposed by the Brazilian Program for Horticulture Modernization. The grade conformity obtained when compared with the one programmed by the packer, was only for large sizes, in both equipments. The electronically equipment has presented better performance, over the mechanical, considering grading quality and fruits post-harvest quality. However, the electronically equipment must be constantly monitored to achieve efficiency and investment return. On the other side, for mechanical equipment it will be necessary to review the actual system of size grading, in order to follow the fresh tomato quality standards.

Caracterização de dois equipamentos de beneficiamento e classificação de tomates para mesa

On the last years, in Brazil, sorting and classifying fruits and vegetables using packing lines have increased. This work aimed at characterizing the cleaning process for fresh market tomatoes at two packing lines, one imported and one national located at Campinas, São Paulo State. Characterization included data, number, types and brushes velocity, water use, fruit standing time and cleaning efficiency. Standing time was measured correlating to fruit diameter (CEAGESP). For measuring cleaning efficiency an equipment was developed that was mainly composed of a ring involved with white cloth. Samples were taken before and after the cleaning step and evaluated using a colorimeter HUNTER Lab. The results showed a strong difference between the two equipments. The imported equipment showed lower number on brushes and rotation than national one, however a higher water consumption. For imported equipments this relation was not found. Both packing lines showed the same cleaning efficiency. Cleaning efficiency is related to be an interaction among the studies parameters, and it could be necessary a better management than the one used on both equipments.

Sistema de sincronismo entre a colhedora de cana-de-açúcar e o veículo de transbordo

One of the problems found in mechanical harvest of sugar cane is the lack of synchronism between the harvest machine and the infield wagon, causing crop losses as well as operational capacity. The objective of the present research was to design a system capable of helping to synchronize the sugar cane harvest machine with the wagon. The communication between tractor and harvest machine is wireless. Two ultrasound sensors coupled to the elevator and a microprocessor manage such information, generating a correct synchronization among the machines. The system was tested in laboratory and on field performing its function adequately, maintaining the two machines in synchronization, indicating and alerting the operators their relative positions. The developed system reduced the sugar cane lost in 60 kg ha-1 comparing to the harvest with the system turned off.

Otimização da eficiência de limpeza em equipamento de beneficiamento de tomate de mesa

The post-harvesting cleaning process in fresh market tomatoes production is essential to the consumer acceptance, since the degree of dirtiness of the fruits is directly related to its quality. However, the washing stage of the cleaning process of commercial packinghouse demands an excessive water volume, bringing serious environmental concerns. The objective of this work was to compare the cleaning efficiency in two cleaning systems through the evaluation of different operational conditions of the cleaning process, related with the brush rotation, water flow and fruit standing time under the system. It was compared the conventional system utilized in commercial equipment with a system using commercial sprays. The results showed that the cleaning efficiency was not directly related to the water volume used, but to the water pressure, standing time and brushes rotation. Therefore, the use of commercial sprays can bring benefits to the cleaning efficiency, increasing it up to 13%, and to the environmental, decreasing water consumption.

Produção de alface hidropônica em três ambientes de cultivo

It was proposed to evaluate the hydroponic lettuce production, variety Vera, on inclined benches with channels of 100 mm, and Nutrient Film Technique, as answer to carbon dioxide application and evaporative cooling. There were five cycles of cultivation from March, 20th to April, 17th (C1); from May, 25th to June, 29th (C2); from July, 13th to August, 20th (C3); from August, 27th to October, 10th (C4); from December, 12th to January, 10th (C5). In three greenhouses were tested the following systems: (A1) without evaporative cooling air CO2 aerial injection, (A2) with CO2 aerial injection and without evaporative cooling and (A3) with CO2 aerial injection and pad-fan evaporative cooling system. The fresh and dry mass of leaves in grams, number of leaves and leaf area in square millimeter were evaluated. The completely randomized statistical analysis was used. The cycle C1 were used 48 replications, for cycles C2, C3 and C5 were used 64 replications and C5 were used 24 replications. The results showed that greenhouse with evaporative cooling system and CO2 allow better development and greater lettuce yield. It was possible to conclude that the aerial injection of CO2, in the absence of evaporative cooling system, did not lead increasing the lettuce productivity to most cycles. Bigger lettuce leaf areas were found in periods with higher temperatures.

Determinação em tempo real da magnitude de danos físicos por impacto em linhas de beneficiamento e em condições de laboratório e seus efeitos na qualidade de tomate

Tomatoes are one of the most important vegetable crops grown in Brazil and are among the crops that have one of the highest post-harvest losses indexes in the country. The present work aimed at evaluating impact damage observed in packing lines of fresh tomatoes as well as to determine, under laboratory conditions, quality alterations of tomato fruits submitted to impact damage in different surface types. Critical points evaluation was accomplished using an instrumented sphere. Critical transference points found showed variations in acceleration levels from 30 to 129 G (m s-2). Tests carried out under laboratory conditions showed that padded surfaces reduced up to 31% impact damage. Incidence of severe internal physical damage was evaluated by a subjective scale and increased by 79% on hard surfaces for the highest fall drop. On the other hand, it was observed an effective reduction in physical damage on fruits when padded surfaces were used. When a 10-cm drop was performed, the maximum reduction measured was 10% for hard surfaces and 5% for previously padded surfaces. For quality parameters, it was observed for high drops on hard surfaces, highest values for weight loss, total acidity, lower values for vitamin C and Soluble Solids.