Extent and mechanism of phase separation during the extrusion of calcium phosphate pastes

The aim of this study was to increase understanding of the mechanism and dominant drivers influencing phase separation during ram extrusion of calcium phosphate (CaP) paste for orthopaedic applications. The liquid content of extrudate was determined, and the flow of liquid and powder phases within the syringe barrel during extrusion were observed, subject to various extrusion parameters. Increasing the initial liquid-to-powder mass ratio, LPR, (0.4-0.45), plunger rate (5-20 mm/min), and tapering the barrel exit (45°-90°) significantly reduced the extent of phase separation. Phase separation values ranged from (6.22 ± 0.69 to 18.94 ± 0.69 %). However altering needle geometry had no significant effect on phase separation. From powder tracing and liquid content determination, static zones of powder and a non-uniform liquid distribution was observed within the barrel. Measurements of extrudate and paste LPR within the barrel indicated that extrudate LPR remained constant during extrusion, while LPR of paste within the barrel decreased steadily. These observations indicate the mechanism of phase separation was located within the syringe barrel. Therefore phase separation can be attributed to either; (1) the liquid being forced downstream by an increase in pore pressure as a result of powder consolidation due to the pressure exerted by the plunger or (2) the liquid being drawn from paste within the barrel, due to suction, driven by dilation of the solids matrix at the barrel exit. Differentiating between these two mechanisms is difficult; however results obtained suggest that suction is the dominant phase separation mechanism occurring during extrusion of CaP paste.

Active corrosion protection of AA2024 by sol-gel coatings with corrosion inhibitors

A indústria aeronáutica utiliza ligas de alumínio de alta resistência para o fabrico dos elementos estruturais dos aviões. As ligas usadas possuem excelentes propriedades mecânicas mas apresentam simultaneamente uma grande tendência para a corrosão. Por esta razão essas ligas necessitam de protecção anticorrosiva eficaz para poderem ser utilizadas com segurança. Até à data, os sistemas anticorrosivos mais eficazes para ligas de alumínio contêm crómio hexavalente na sua composição, sejam pré-tratamentos, camadas de conversão ou pigmentos anticorrosivos. O reconhecimento dos efeitos carcinogénicos do crómio hexavalente levou ao aparecimento de legislação banindo o uso desta forma de crómio pela indústria. Esta decisão trouxe a necessidade de encontrar alternativas ambientalmente inócuas mas igualmente eficazes. O principal objectivo do presente trabalho é o desenvolvimento de prétratamentos anticorrosivos activos para a liga de alumínio 2024, baseados em revestimentos híbridos produzidos pelo método sol-gel. Estes revestimentos deverão possuir boa aderência ao substrato metálico, boas propriedades barreira e capacidade anticorrosiva activa. A protecção activa pode ser alcançada através da incorporação de inibidores anticorrosivos no prétratamento. O objectivo foi atingido através de uma sucessão de etapas. Primeiro investigou-se em detalhe a corrosão localizada (por picada) da liga de alumínio 2024. Os resultados obtidos permitiram uma melhor compreensão da susceptibilidade desta liga a processos de corrosão localizada. Estudaram-se também vários possíveis inibidores de corrosão usando técnicas electroquímicas e microestruturais. Numa segunda etapa desenvolveram-se revestimentos anticorrosivos híbridos orgânico-inorgânico baseados no método sol-gel. Compostos derivados de titania e zirconia foram combinados com siloxanos organofuncionais a fim de obter-se boa aderência entre o revestimento e o substrato metálico assim como boas propriedades barreira. Testes industriais mostraram que estes novos revestimentos são compatíveis com os esquemas de pintura convencionais actualmente em uso. A estabilidade e o prazo de validade das formulações foram optimizados modificando a temperatura de armazenamento e a quantidade de água usada durante a síntese. As formulações sol-gel foram dopadas com os inibidores seleccionados durante a primeira etapa e as propriedades anticorrosivas passivas e activas dos revestimentos obtidos foram estudadas numa terceira etapa do trabalho. Os resultados comprovam a influência dos inibidores nas propriedades anticorrosivas dos revestimentos sol-gel. Em alguns casos a acção activa dos inibidores combinou-se com a protecção passiva dada pelo revestimento mas noutros casos terá ocorrido interacção química entre o inibidor e a matriz de sol-gel, de onde resultou a perda de propriedades protectoras do sistema combinado. Atendendo aos problemas provocados pela adição directa dos inibidores na formulação sol-gel procurou-se, numa quarta etapa, formas alternativas de incorporação. Na primeira, produziu-se uma camada de titania nanoporosa na superfície da liga metálica que serviu de reservatório para os inibidores. O revestimento sol-gel foi aplicado por cima da camada nanoporosa. Os inibidores armazenados nos poros actuam quando o substrato fica exposto ao ambiente agressivo. Numa segunda, os inibidores foram armazenados em nano-reservatórios de sílica ou em nanoargilas (halloysite), os quais foram revestidos por polielectrólitos montados camada a camada. A terceira alternativa consistiu no uso de nano-fios de molibdato de cério amorfo como inibidores anticorrosivos nanoparticulados. Os nano-reservatórios foram incorporados durante a síntese do sol-gel. Qualquer das abordagens permitiu eliminar o efeito negativo do inibidor sobre a estabilidade da matriz do sol-gel. Os revestimentos sol-gel desenvolvidos neste trabalho apresentaram protecção anticorrosiva activa e capacidade de auto-reparação. Os resultados obtidos mostraram o elevado potencial destes revestimentos para a protecção anticorrosiva da liga de alumínio 2024.

Novel furan polymer materials based on the reversible Diels-Alder reaction

A futura e inevitável escassez dos recursos fósseis, juntamente com o aumento imprevisível dos seus preços, levou, nas últimas décadas, a um aumento impressionante de iniciativas dedicadas não só à procura de fontes alternativas de fornecedores de energia, mas também de produtos químicos e polímeros a partir de fontes renováveis, em particular da biomassa vegetal. Entre estes, os polímeros derivados de monómeros furânicos constituem uma classe única de materiais cujas estruturas podem, em princípio, simular virtualmente os seus homólogos actualmente derivados de recursos fósseis. O anel furânico é uma estrutura heterocíclica com um carácter diénico pronunciado, o que torna-o um dieno particularmente apropriado para a reacção de Diels-Alder (DA) com dienófilos como a maleimida. Um dos aspectos mais relevantes da reacção de DA é a sua reversibilidade em função da temperatura, a qual permite que os aductos sejam facilmente revertidos nos seus precursores por aumento da temperatura (reacção de retro-DA). No caso específico da combinação furano-maleimida, a formação do aducto predomina até cerca de 60ºC, enquanto a reacção inversa é dominante acima de 100ºC. A combinação desta característica da reacção de DA com a química de compostos furânicos pode abrir um novo caminho para a preparação de materiais macromoleculares funcionais com base em fontes renováveis e com aplicações promissoras como auto-reparação e reciclabilidade. O principal objectivo desta Tese, é a síntese e caracterização de novos materiais poliméricos termo-reversíveis, aplicando a reacção de DA a monómeros complementares com estruturas dos tipos furânico (o dieno, designado por A) e de maleimida (o dienófilo, designado por B). A primeira etapa neste trabalho envolveu a síntese, purificação e caracterização de novos monómeros furânicos e de maleimida do tipo AA, A3, BB, B3, AB, AB2, cada um com diferentes grupos separadores das funções reactivas. Posteriormente, estes monómeros foram polimerizados e despolimerizados por ciclos de DA/retro-DA utilizando diferentes combinações. A formação e dissociação de todos os aductos de DA foram seguidas por ambas espectroscopias de UV e RMN de 1H. O primeiro sistema de DA estudado foi uma combinação modelo entre reagentes mono-funcionais (-A+-B), nomeadamente o acetato furfurílico (FA) e a N-metilmaleimida (MM), ambos comercialmente disponíveis. O objectivo desta abordagem foi estudar a cinética e o equilíbrio da formação/dissociação dos aductos de DA e obter indicações sobre as condições mais adequadas a serem usadas na preparação dos correspondentes novos materiais macromoleculares. Além disso, pretendia-se verificar a presença ou ausência de reacções secundárias que poderiam intervir em ambas as vias directa e inversa das reacções, mesmo após vários ciclos. A espectroscopia de UV forneceu informação quantitativa sobre a cinética de formação do aducto através da diminuição progressiva da absorvência máxima a 293 nm correspondente ao grupo maleimida, a diferentes temperaturas (35, 50, 65 ºC) Reciprocamente, a correspondente reacção de retro-DA foi seguida a 90 ºC através do aumento do mesmo pico. A reversibilidade destes sistemas foi verificada com sucesso após uma sequência de ciclos de DA/retro-DA. Adicionalmente, verificou-se que os espectros originaram um ponto isosbéstico, provando que estes sistemas não envolvem quaisquer reacções secundárias. Uma vez que foi usado um excesso de FA, as reacções de DA modelo apresentaram um comportamento cinético de pseudo-primeira ordem, com a constante de velocidade k mais alta (2.1x10-5 dm3mol-1s-1) para T=65 ºC. A correspondente energia de activação foi de 39.0 kJ.mol-1. A reacção de retro-DA seguiu um comportamento de primeira ordem, com constante de velocidade de 1.6x10-6 s-1. A evolução deste sistema por RMN de 1H a 65ºC deu-nos informações mais detalhadas sobre a sua evolução estrutural, ou seja, à medida que a intensidade dos picos atribuídos à formação do aducto aumentaram progressivamente ao longo do tempo, os pertencentes aos reagentes iniciais diminuiram proporcionalmente. O “rendimento final”, calculado após 20 dias à temperatura ambiente, foi de aproximadamente 70%. A reacção de retro-DA foi depois seguida a 90ºC, observando-se tal como na espectroscopia de UV, o deslocamento da reacção no sentido da regeneração dos reagentes de partida. A viabilidade de múltiplos ciclos de DA/retro-DA estabelecidos pela espectroscopia de UV foi igualmente confirmada por RMN de 1H. O passo seguinte envolveu o estudo de um sistema de policondensação linear baseado no crescimento gradual por reacção de DA entre um monómero bisfurânico A-A e um do tipo bismaleimida B-B, seguindo a mesma abordagem que no sistema modelo. O poliaducto linear foi obtido a partir de soluções equimolares dos monómeros, por reacção de DA a 65ºC. O progresso desta polimerização foi seguido por espectroscopia de UV e RMN de 1H e, mais qualitativamente, pelo aumento da viscosidade do meio. A reacção seguiu um comportamento de segunda ordem, com uma constante de velocidade de 9.4x10-6 dm3mol-1s-1, e observou-se novamente um ponto isosbéstico nos dados de UV. Os espectros de RMN apresentaram o padrão esperado, nomeadamente o aumento progressivo dos sinais associados ao aducto e a correspondente diminuição dos grupos furano e maleimida livres. A despolimerização do poliaducto através da reacção de retro-DA foi seguida a 110ºC usando as mesmas técnicas. Os dados de UV mostraram o retorno progressivo da absorção dos grupos de maleimida, seguindo um comportamento cinético de primeira ordem, com constante de velocidade de 2.5x10-6 s-1, até à completa regeneração de ambos os monómeros. Os espectros de RMN providenciaram mais uma vez informação estrutural sobre o progresso da despolimerização, a qual foi acompanhada por uma diminuição progressiva da viscosidade. Adicionalmente, para seguir a retro- DA, adicionou-se um excesso de composto furânico monofuncional, nomeadamente o 2,5-dimetilfurano (DMFu), ao sistema de modo a bloquear as funções maleimida complementares, evitando assim a repolimerização após arrefecimento. Os productos isolados foram então o monómero bisfurânico AA, DMFu que não reagiu e o bisaducto não-polimerizável de BB com DMFu. Este resultado indicou claramente que o polímero foi de facto revertido nos seus monómeros durante a reacção de retro-DA. O terceiro sistema estudado foi outra polimerização linear, seguindo as mesmas condições experimentais que os anteriores, mas com uma estratégia diferente de modo a contornar o problema clássico de assegurar a estequiometria exacta dos monómeros. As estruturas dos monómeros utilizados incorporam ambos os grupos reactivos, i.e, moléculas do tipo A-B. A polimerização prematura destes monómeros intrinsecamente reactivos foi evitada com a protecção do grupo maleimida na forma de um aducto de DA com furano, até a incorporação do substituinte furânico na outra extremidade. Portanto, a policondensação destes monómeros foi iniciada após a desprotecção in situ deste composto mediante aquecimento, seguido de arrefecimento até à temperatura adequada para polimerizar. Os resultados obtidos por UV e RMN sugerem que de facto o uso de monómeros do tipo A-B oferece um melhor sistema linear. Em seguida, foram estudados sistemas de policondensação não-linear por reacção de DA, entre monómeros (um ou ambos) com funcionalidade superior a dois, nomeadamente sistemas do tipo A3+B-B ou A-A+B3, seguindo mais uma vez as mesmas condições experimentais. Uma vez que utilizam monómeros complementares contendo, em média, mais de duas funcionalidades, estes sistemas conduzem a materiais reticulados. Nestes estudos, foram usadas três razões molares de [maleimida]/[furano], nomeadamente 1.0, 0.75 e 0.5, de modo a estudar ambas as situações de não-gelificação e reticulação. Ambos sistemas apresentaram um comportamento regular e boa reciclabilidade quer para gerar situações que possam conduzir à formação de redes a diferentes graus de conversão, ou que possam parar antes da sua obtenção, conforme previsto pela equação de Flory-Stockmayer. Como esperado, a utilização de grupos complementares em quantidades estequiométricas produziu o espessamento mais rápido e a reticulação quase completa; à medida que a quantidade relativa de monómero trifuncional decresceu, as reacções pararam antes da reticulação, ou seja, originaram meios altamente viscosos contendo polímeros solúveis altamente ramificados. As reacções de retro-DA a 110 ºC conduziram à gradual dissolução das partículas de gel (quando presentes), tendo sido comprovado pelos espectros de UV e de RMN de 1H, evidenciado a regeneração dos monómeros. Tal como no sistema do tipo A-A+B-B, a reacção de retro-DA foi seguida adicionando um excesso de DMFu ao sistema reaccional. Como esperado, os produtos finais foram os monómeros furânicos, o DMFu em excesso e o trisaducto ou o bisaducto maleimida-DMFu, o que confirma a eficiência da despolimerização com regeneração dos monómeros iniciais. O último sistema de policondensação por reacção de DA envolveu um monómero assimetricamente substituído do tipo AB2, capaz de originar estruturas macromoleculares hiper-ramificadas que não reticulam. Este estudo preliminar deste sistema foi seguido nas mesmas condições experimentais que os anteriores, apresentando um comportamento com as características esperadas.

Study of multiferroic materials

The present PhD work aims the research and development of materials that exhibit multiferroic properties, in particular having a significant interaction between ferromagnetism and ferroelectricity; either directly within an intrinsic single phase or by combining extrinsic materials, achieving the coupling of properties through mechanic phenomena of the respective magnetostriction and piezoelectricity. These hybrid properties will allow the cross modification of magnetic and electric polarization states by the application of cross external magnetic and/or electric fields, giving way to a vast area for scientific investigation and potential technological applications in a new generation of electronic devices, such as computer memories, signal processing, transducers, sensors, etc. Initial experimental work consisted in chemical synthesis of nano powders oxides by urea pyrolysis method: A series of ceramic bulk composites with potential multiferroic properties comprised: of LuMnO3 with La0.7Sr0.3MnO3 and BaTiO3 with La0.7Ba0.3MnO3; and a series based on the intrinsic multiferroic LuMn1-zO3 phase modified with of Manganese vacancies. The acquisition of a new magnetron RF sputtering deposition system, in the Physics Department of Aveiro University, contributed to the proposal of an analogous experimental study in multiferroic thin films and multilayer samples. Besides the operational debut of this equipment several technical upgrades were completed like: the design and construction of the heater electrical contacts; specific shutters and supports for the magnetrons and for the substrate holder and; the addition of mass flow controllers, which allowed the introduction of N2 or O2 active atmosphere in the chamber; and the addition of a second RF generator, enabling co-deposition of different targets. Base study of the deposition conditions and resulting thin films characteristics in different substrates was made from an extensive list of targets. Particular attention was given to thin film deposition of magnetic phases La1-xSrxMnO3, La1-xBaxMnO3 and Ni2+x-yMn1-xGa1+y alloy, from the respective targets: La0.7Sr0.3MnO3, La0.7Ba0.3MnO3; and NiGa with NiMn. Main structural characterization of samples was performed by conventional and high resolution X-Ray Diffraction (XRD); chemical composition was determined by Electron Dispersion Spectroscopy (EDS); magnetization measurements recur to a Vibrating Sample Magnetometer (VSM) prototype; and surface probing (SPM) using Magnetic-Force (MFM) and Piezo-Response (PFM) Microscopy. Results clearly show that the composite bulk samples (LuM+LSM and BTO+LBM) feat the intended quality objectives in terms of phase composition and purity, having spurious contents below 0.5 %. SEM images confirm compact grain packaging and size distribution around the 50 nm scale. Electric conductivity, magnetization intensity and magneto impedance spreading response are coherent with the relative amount of magnetic phase in the sample. The existence of coupling between the functional phases is confirmed by the Magnetoelectric effect measurements of the sample “78%LuM+22%LSM” reaching 300% of electric response for 1 T at 100 kHz; while in the “78%BTO+22%LBM” sample the structural transitions of the magnetic phase at ~350 K result in a inversion of ME coefficient the behavior. A functional Magneto-Resistance measurement system was assembled from the concept stage until the, development and operational status; it enabled to test samples from 77 to 350 K, under an applied magnetic field up to 1 Tesla with 360º horizontal rotation; this system was also designed to measure Hall effect and has the potential to be further upgraded. Under collaboration protocols established with national and international institutions, complementary courses and sample characterization studies were performed using Magneto-Resistance (MR), Magneto-Impedance (MZ) and Magneto-Electric (ME) measurements; Raman and X-ray Photoelectron Spectroscopy (XPS); SQUID and VSM magnetization; Scanning Electron Microscopy (SEM) and Rutherford Back Scattering (RBS); Scan Probe Microscopy (SPM) with Band Excitation Probe Spectroscopy (BEPS); Neutron Powder Diffraction (NPD) and Perturbed Angular Correlations (PAC). Additional collaboration in research projects outside the scope of multiferroic materials provided further experience in sample preparation and characterization techniques, namely VSM and XPS measurements were performed in cubane molecular complex compounds and enable to identify the oxidation state of the integrating cluster of Ru ions; also, XRD and EDS/SEM analysis of the acquired targets and substrates implied the devolution of some items not in conformity with the specifications. Direct cooperation with parallel research projects regarding multiferroic materials, enable the assess to supplementary samples, namely a preliminary series of nanopowder Y1-x-yCaxØyMn1O3 and of Eu0.8Y0.2MnO3, a series of micropowder composites of LuMnO3 with La0.625Sr0.375MnO3 and of BaTiO3 with hexagonal ferrites; mono and polycrystalline samples of Pr1-xCaxMnO3, La1-xSrxMnO3 and La1-xCaxMnO3.

Estratégias de alteração da funcionalidade de proteínas de soja

Este trabalho teve como principal objetivo estudar e modificar as propriedades funcionais das proteínas de soja de forma a otimizar e diversificar a sua aplicação industrial. Para tal, foram propostas e estudadas quatro estratégias: i) extração do isolado de proteínas de soja (IPS) a partir de diferentes matérias-primas, ii) adição de galactomananas (GM) com graus de ramificação e massas moleculares diferentes, iii) hidrólise enzimática controlada das proteínas de soja, iv) processamento por alta pressão hidrostática. O estudo e a interpretação da influência destas estratégias sobre as propriedades funcionais das proteínas de soja, nomeadamente, na capacidade gelificante e emulsionante, foram realizados recorrendo fundamentalmente a ensaios reológicos dinâmicos a baixas deformação, espectroscopia de infravermelho, electroforeses, calorimetria diferencial de varrimento e ensaios de microscopia confocal de varrimento laser. O estudo da extração e caracterização dos isolados de proteínas de soja obtidos a partir de diferentes matérias-primas permitiu concluir que as caraterísticas físico-químicas dos isolados são dependentes da origem da matéria-prima de extração e da severidade dos tratamentos industriais prévios à extração do isolado. Contudo, as propriedades viscoelásticas dos géis obtidos por aquecimento controlado não foram significativamente distintas embora tenha sido possível relacionar o grau de agregação com a diminuição da temperatura de gelificação e com o aumento inicial dos módulos viscoelásticos. As alterações sofridas pelos isolados de origem comercial mostraram ser irreversíveis resultando em géis menos rígidos e com maior caráter viscoso. A adição de galactomanana alterou significativamente o mecanismo de gelificação induzido termicamente das proteínas de soja, bem como as propriedades viscoelásticas dos géis e a microestrutura dos géis, demonstrando-se a ocorrência de separação de fases, em virtude da incompatibilidade termodinâmica entre os biopolímeros, resultando em géis mais rígidos e no decréscimo da temperatura de gelificação. A extensão destas alterações foi dependente da massa molecular, grau de ramificação e da razão IPS/GM. O efeito da hidrólise enzimática por ação da bromelina, nas propriedades gelificantes e emulsionantes das proteínas de soja, mostrou ser dependente do grau de hidrólise (GH). Valores de GH inferiores a 15 % melhoraram as propriedades gelificantes das proteínas de soja. Por outro lado, o aumento do GH teve um efeito negativo nas propriedades emulsionantes, o qual foi atenuado por adição da goma de alfarroba, com efeito positivo na gelificação das proteínas de soja. A concentração crítica limite de compatibilidade entre os hidrolisados de proteína de soja e a goma de alfarroba aumentou com o decréscimo do GH e da massa molecular do polissacacrídeo. O efeito da AP sobre as propriedades físico-químicas e funcionais dos IPS foi influenciado pela origem do isolado e pelas condições de tratamento. O processamento até 100 MPa desencadeou um aumento da atividade emulsionante e considerável melhoria da capacidade gelificante. Contudo, valores de pressão superiores promoveram a desnaturação das proteínas constituintes dos isolados, resultando no decréscimo da temperatura de gelificação e numa re-associação das subunidades proteicas, diminuindo a elasticidade dos géis finais. Os resultados sugeriram que as alterações nas proteínas de soja promovidas durante o tratamento por AP constituem um fator limitante para o desdobramento e re-associação durante o aquecimento térmico, necessários para a formação e fortalecimento de gel formado. O processamento por AP influenciou a estrutura secundária e a microestrutura das amostras. A presença de GA teve um papel baroprotetor. Assim, com este trabalho demonstrou-se que com as estratégias seguidas para manipulação das propriedades funcionais de proteínas de soja, nomeadamente através da adição de um polissacarídeo com propriedades estruturais controladas, da adequada combinação da adição de um polissacarídeo neutro com a hidrólise controlada das proteínas ou com tratamento por alta pressão, é possível a criação de novas funcionalidades, com utilidade no desenvolvimento de novas formulações alimentares, permitindo expandir a aplicação destas proteínas vegetais.

Ferroelectric : CNTs structures fabrication for advanced functional nano devices

This work is about the combination of functional ferroelectric oxides with Multiwall Carbon Nanotubes for microelectronic applications, as for example potential 3 Dimensional (3D) Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Miniaturized electronics are ubiquitous now. The drive to downsize electronics has been spurred by needs of more performance into smaller packages at lower costs. But the trend of electronics miniaturization challenges board assembly materials, processes, and reliability. Semiconductor device and integrated circuit technology, coupled with its associated electronic packaging, forms the backbone of high-performance miniaturized electronic systems. However, as size decreases and functionalization increases in the modern electronics further size reduction is getting difficult; below a size limit the signal reliability and device performance deteriorate. Hence miniaturization of siliconbased electronics has limitations. On this background the Road Map for Semiconductor Industry (ITRS) suggests since 2011 alternative technologies, designated as More than Moore; being one of them based on carbon (carbon nanotubes (CNTs) and graphene) [1]. CNTs with their unique performance and three dimensionality at the nano-scale have been regarded as promising elements for miniaturized electronics [2]. CNTs are tubular in geometry and possess a unique set of properties, including ballistic electron transportation and a huge current caring capacity, which make them of great interest for future microelectronics [2]. Indeed CNTs might have a key role in the miniaturization of Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Moving from a traditional two dimensional (2D) design (as is the case of thin films) to a 3D structure (based on a tridimensional arrangement of unidimensional structures) will result in the high reliability and sensing of the signals due to the large contribution from the bottom electrode. One way to achieve this 3D design is by using CNTs. Ferroelectrics (FE) are spontaneously polarized and can have high dielectric constants and interesting pyroelectric, piezoelectric, and electrooptic properties, being a key application of FE electronic memories. However, combining CNTs with FE functional oxides is challenging. It starts with materials compatibility, since crystallization temperature of FE and oxidation temperature of CNTs may overlap. In this case low temperature processing of FE is fundamental. Within this context in this work a systematic study on the fabrication of CNTs - FE structures using low cost low temperature methods was carried out. The FE under study are comprised of lead zirconate titanate (Pb1-xZrxTiO3, PZT), barium titanate (BaTiO3, BT) and bismuth ferrite (BiFeO3, BFO). The various aspects related to the fabrication, such as effect on thermal stability of MWCNTs, FE phase formation in presence of MWCNTs and interfaces between the CNTs/FE are addressed in this work. The ferroelectric response locally measured by Piezoresponse Force Microscopy (PFM) clearly evidenced that even at low processing temperatures FE on CNTs retain its ferroelectric nature. The work started by verifying the thermal decomposition behavior under different conditions of the multiwall CNTs (MWCNTs) used in this work. It was verified that purified MWCNTs are stable up to 420 ºC in air, as no weight loss occurs under non isothermal conditions, but morphology changes were observed for isothermal conditions at 400 ºC by Raman spectroscopy and Transmission Electron Microscopy (TEM). In oxygen-rich atmosphere MWCNTs started to oxidized at 200 ºC. However in argon-rich one and under a high heating rate MWCNTs remain stable up to 1300 ºC with a minimum sublimation. The activation energy for the decomposition of MWCNTs in air was calculated to lie between 80 and 108 kJ/mol. These results are relevant for the fabrication of MWCNTs – FE structures. Indeed we demonstrate that PZT can be deposited by sol gel at low temperatures on MWCNTs. And particularly interesting we prove that MWCNTs decrease the temperature and time for formation of PZT by ~100 ºC commensurate with a decrease in activation energy from 68±15 kJ/mol to 27±2 kJ/mol. As a consequence, monophasic PZT was obtained at 575 ºC for MWCNTs - PZT whereas for pure PZT traces of pyrochlore were still present at 650 ºC, where PZT phase formed due to homogeneous nucleation. The piezoelectric nature of MWCNTs - PZT synthesised at 500 ºC for 1 h was proved by PFM. In the continuation of this work we developed a low cost methodology of coating MWCNTs using a hybrid sol-gel / hydrothermal method. In this case the FE used as a proof of concept was BT. BT is a well-known lead free perovskite used in many microelectronic applications. However, synthesis by solid state reaction is typically performed around 1100 to 1300 ºC what jeopardizes the combination with MWCNTs. We also illustrate the ineffectiveness of conventional hydrothermal synthesis in this process due the formation of carbonates, namely BaCO3. The grown MWCNTs - BT structures are ferroelectric and exhibit an electromechanical response (15 pm/V). These results have broad implications since this strategy can also be extended to other compounds of materials with high crystallization temperatures. In addition the coverage of MWCNTs with FE can be optimized, in this case with non covalent functionalization of the tubes, namely with sodium dodecyl sulfate (SDS). MWCNTs were used as templates to grow, in this case single phase multiferroic BFO nanorods. This work shows that the use of nitric solvent results in severe damages of the MWCNTs layers that results in the early oxidation of the tubes during the annealing treatment. It was also observed that the use of nitric solvent results in the partial filling of MWCNTs with BFO due to the low surface tension (<119 mN/m) of the nitric solution. The opening of the caps and filling of the tubes occurs simultaneously during the refluxing step. Furthermore we verified that MWCNTs have a critical role in the fabrication of monophasic BFO; i.e. the oxidation of CNTs during the annealing process causes an oxygen deficient atmosphere that restrains the formation of Bi2O3 and monophasic BFO can be obtained. The morphology of the obtained BFO nano structures indicates that MWCNTs act as template to grow 1D structure of BFO. Magnetic measurements on these BFO nanostructures revealed a week ferromagnetic hysteresis loop with a coercive field of 956 Oe at 5 K. We also exploited the possible use of vertically-aligned multiwall carbon nanotubes (VA-MWCNTs) as bottom electrodes for microelectronics, for example for memory applications. As a proof of concept BiFeO3 (BFO) films were in-situ deposited on the surface of VA-MWCNTs by RF (Radio Frequency) magnetron sputtering. For in situ deposition temperature of 400 ºC and deposition time up to 2 h, BFO films cover the VA-MWCNTs and no damage occurs either in the film or MWCNTs. In spite of the macroscopic lossy polarization behaviour, the ferroelectric nature, domain structure and switching of these conformal BFO films was verified by PFM. A week ferromagnetic ordering loop was proved for BFO films on VA-MWCNTs having a coercive field of 700 Oe. Our systematic work is a significant step forward in the development of 3D memory cells; it clearly demonstrates that CNTs can be combined with FE oxides and can be used, for example, as the next 3D generation of FERAMs, not excluding however other different applications in microelectronics.

Electromechanical properties of engineered lead free potassium sodium niobate based materials

K0.5Na0.5NbO3 (KNN), is the most promising lead free material for substituting lead zirconate titanate (PZT) which is still the market leader used for sensors and actuators. To make KNN a real competitor, it is necessary to understand and to improve its properties. This goal is pursued in the present work via different approaches aiming to study KNN intrinsic properties and then to identify appropriate strategies like doping and texturing for designing better KNN materials for an intended application. Hence, polycrystalline KNN ceramics (undoped, non-stoichiometric; NST and doped), high-quality KNN single crystals and textured KNN based ceramics were successfully synthesized and characterized in this work. Polycrystalline undoped, non-stoichiometric (NST) and Mn doped KNN ceramics were prepared by conventional ceramic processing. Structure, microstructure and electrical properties were measured. It was observed that the window for mono-phasic compositions was very narrow for both NST ceramics and Mn doped ceramics. For NST ceramics the variation of A/B ratio influenced the polarization (P-E) hysteresis loop and better piezoelectric and dielectric responses could be found for small stoichiometry deviations (A/B = 0.97). Regarding Mn doping, as compared to undoped KNN which showed leaky polarization (P-E) hysteresis loops, B-site Mn doped ceramics showed a well saturated, less-leaky hysteresis loop and a significant properties improvement. Impedance spectroscopy was used to assess the role of Mn and a relation between charge transport – defects and ferroelectric response in K0.5Na0.5NbO3 (KNN) and Mn doped KNN ceramics could be established. At room temperature the conduction in KNN which is associated with holes transport is suppressed by Mn doping. Hence Mn addition increases the resistivity of the ceramic, which proved to be very helpful for improving the saturation of the P-E loop. At high temperatures the conduction is dominated by the motion of ionized oxygen vacancies whose concentration increases with Mn doping. Single crystals of potassium sodium niobate (KNN) were grown by a modified high temperature flux method. A boron-modified flux was used to obtain the crystals at a relatively low temperature. XRD, EDS and ICP analysis proved the chemical and crystallographic quality of the crystals. The grown KNN crystals exhibit higher dielectric permittivity (29,100) at the tetragonal-to-cubic phase transition temperature, higher remnant polarization (19.4 μC/cm2) and piezoelectric coefficient (160 pC/N) when compared with the standard KNN ceramics. KNN single crystals domain structure was characterized for the first time by piezoforce response microscopy. It could be observed that <001> - oriented potassium sodium niobate (KNN) single crystals reveal a long range ordered domain pattern of parallel 180° domains with zig-zag 90° domains. From the comparison of KNN Single crystals to ceramics, It is argued that the presence in KNN single crystal (and absence in KNN ceramics) of such a long range order specific domain pattern that is its fingerprint accounts for the improved properties of single crystals. These results have broad implications for the expanded use of KNN materials, by establishing a relation between the domain patterns and the dielectric and ferroelectric response of single crystals and ceramics and by indicating ways of achieving maximised properties in KNN materials. Polarized Raman analysis of ferroelectric potassium sodium niobate (K0.5Na0.5)NbO3 (KNN) single crystals was performed. For the first time, an evidence is provided that supports the assignment of KNN single crystals structure to the monoclinic symmetry at room temperature. Intensities of A′, A″ and mixed A′+A″ phonons have been theoretically calculated and compared with the experimental data in dependence of crystal rotation, which allowed the precise determination of the Raman tensor coefficients for (non-leaking) modes in monoclinic KNN. In relation to the previous literature, this study clarifies that assigning monoclinic phase is more suitable than the orthorhombic one. In addition, this study is the basis for non-destructive assessments of domain distribution by Raman spectroscopy in KNN-based lead-free ferroelectrics with complex structures. Searching a deeper understanding of the electrical behaviour of both KNN single crystal and polycrystalline materials for the sake of designing optimized KNN materials, a comparative study at the level of charge transport and point defects was carried out by impedance spectroscopy. KNN single crystals showed lower conductivity than polycrystals from room temperature up to 200 ºC, but above this temperature polycrystalline KNN displays lower conductivity. The low temperature (T < 200 ºC) behaviour reflects the different processing conditions of both ceramics and single crystals, which account for less defects prone to charge transport in the case of single crystals. As temperature increases (T > 200 ºC) single crystals become more conductive than polycrystalline samples, in which grain boundaries act as barriers to charge transport. For even higher temperatures the conductivity difference between both is increased due to the contribution of ionic conduction in single crystals. Indeed the values of activation energy calculated to the high temperature range (T > 300 ºC) were 1.60 and 0.97 eV, confirming the charge transport due to ionic conduction and ionized oxygen vacancies in single crystals and polycrystalline KNN, respectively. It is suggested that single crystals with low defects content and improved electromechanical properties could be a better choice for room temperature applications, though at high temperatures less conductive ceramics may be the choice, depending on the targeted use. Aiming at engineering the properties of KNN polycrystals towards the performance of single crystals, the preparation and properties study of (001) – oriented (K0.5Na0.5)0.98Li0.02NbO3 (KNNL) ceramics obtained by templated grain growth (TGG) using KNN single crystals as templates was undertaken. The choice of KNN single crystals templates is related with their better properties and to their unique domain structure which were envisaged as a tool for templating better properties in KNN ceramics too. X-ray diffraction analysis revealed for the templated ceramics a monoclinic structure at room temperature and a Lotgering factor (f) of 40% which confirmed texture development. These textured ceramics exhibit a long range ordered domain pattern consisting of 90º and 180º domains, similar to the one observed in the single crystals. Enhanced dielectric (13017 at TC), ferroelectric (2Pr = 42.8 μC/cm2) and piezoelectric (d33 = 280 pC/N) properties are observed for textured KNNL ceramics as compared to the randomly oriented ones. This behaviour is suggested to be due to the long range ordered domain patterns observed in the textured ceramics. The obtained results as compared with the data previously reported on texture KNN based ceramics confirm that superior properties were found due to ordered repeated domain pattern. This study provides an useful approach towards properties improvement of KNN-based piezoelectric ceramics. Overall, the present results bring a significant contribution to the pool of knowledge on the properties of sodium potassium niobate materials: a relation between the domain patterns and di-, ferro-, and piezo-electric response of single crystals and ceramics was demonstrated and ways of engineering maximised properties in KNN materials, for example by texturing were established. This contribution is envisaged to have broad implications for the expanded use of KNN over the alternative lead-based materials.

Translating proteomics into environmental health : biomarkers discovery for tobacco smoke-induced biological damage

Tese de doutoramento, Biologia (Biologia Molecular), Universidade de Lisboa, Faculdade de Ciências, 2015

Síntese sol-gel de biomateriais à base de água de fontes hidrotermais para otimização do comportamento celular e regeneração dos tecidos ósseos

Dissertação de Mestrado, Ciências Biomédicas, 18 de Março de 2016, Universidade dos Açores.

Fluorometric monitoring of the properties of proteins entrapped in sol-gel derived matrices

The successful development of stable biosensors incorporating entrapped proteins suffers from poor understanding of the properties of the entrapped biomolecules. This thesis reports on the use of fluorescence spectroscopy to investigate the properties of proteins entrapped in sol-gel processed silicate materials. Two different single tryptophan (Trp) proteins were investigated in this thesis, the Ca2 + binding protein cod III parvalbumin (C3P) and the salicylate binding protein human serum albumin (HSA). Furthermore, the reactive single cysteine (Cys) residue within C3P and HSA were labelled with the probes iodoacetoxynitrobenzoxadiazole (C3P) and acrylodan (C3P and HSA) to further examine the structure, stability and function of the free and entrapped proteins. The results show that both C3P and HSA can be successfully entrapped into sol-gelderived matrices with retention of function and conformational flexibility.

Investigation of Frustrated Quasi-One-Dimensional Quantum Spin-Chain Materials

Copper arsenite CuAs2O4 and Copper antimonite CuSb2O4 are S=1/2 (Cu2+ 3d9 electronic configuration) quasi-one-dimensional quantum spin-chain compounds. Both compounds crystallize with tetragonal structures containing edge sharing CuO6 octahedra chains which experience Jahn-Teller distortions. The basal planes of the octahedra link together to form CuO2 ribbon-chains which harbor Cu2+ spin-chains. These compounds are magnetically frustrated with competing nearest-neighbour and next-nearest-neighbour intrachain spin-exchange interactions. Despite the similarities between CuAs2O4 and CuSb2O4, they exhibit very different magnetic properties. In this thesis work, the physical properties of CuAs2O4 and CuSb2O4 are investigated using a variety of experimental techniques which include x-ray diffraction, magnetic susceptibility measurements, heat capacity measurements, Raman spectroscopy, electron paramagnetic resonance, neutron diffraction, and dielectric capacitance measurements. CuAs2O4 exhibits dominant ferromagnetic nearest-neighbour and weaker antiferromagnetic next-nearest-neighbour intrachain spin-exchange interactions. The ratio of the intrachain interactions amounts to Jnn/Jnnn = -4.1. CuAs2O4 was found to order with a ferromagnetic groundstate below TC = 7.4 K. An extensive physical characterization of the magnetic and structural properties of CuAs2O4 was carried out. Under the effect of hydrostatic pressure, CuAs2O4 was found to undergo a structural phase transition at 9 GPa to a new spin-chain structure. The structural phase transition is accompanied by a severe alteration of the magnetic properties. The high-pressure phase exhibits dominant ferromagnetic next-nearest-neighbour spin-exchange interactions and weaker ferromagnetic nearest-neighbour interactions. The ratio of the intrachain interactions in the high-pressure phase was found to be Jnn/Jnnn = 0.3. Structural and magnetic characterizations under hydrostatic pressure are reported and a relationship between the structural and magnetic properties was established. CuSb2O4 orders antiferromagnetically below TN = 1.8 K with an incommensurate helicoidal magnetic structure. CuSb2O4 is characterized by ferromagnetic nearest-neighbour and antiferromagnetic next-nearest-neighbour spin-exchange interactions with Jnn/Jnnn = -1.8. A (H, T) magnetic phase diagram was constructed using low-temperature magnetization and heat capacity measurements. The resulting phase diagram contains multiple phases as a consequence of the strong intrachain magnetic frustration. Indications of ferroelectricity were observed in the incommensurate antiferromagnetic phase.

Single-Molecule Magnets and Multifunctional Molecular Magnetic Materials Based on Polynuclear Metal Complexes

Our work on single molecule magnets and multifunctional magnetic materials is presented in four projects. In the first project we show for first time that heteroatomic-type pseudohalides, such as OCN-, can be employed as structure-directing ligands and ferromagnetic couplers in higher oxidation state metal cluster chemistry. The initial use of cyanato groups in Mn cluster chemistry has afforded structurally interesting MnII/III14 (1) and MnII/III/IV16 (2) clusters in which the end-on bridging cyanates show a preference in binding through their O-atom. The Mn14 compound shows entirely visible out-of-phase alternating currect signals below 5 K and large hysteresis loops below 2 K. Furthermore, the amalgamation of azido groups with the triethanolamine tripodal ligand in manganese carboxylate cluster chemistry has led to the isolation of a new ferromagnetic, high-nuclearity and mixed-valence MnII/III15Na2 (3) cluster with a large ground-state spin value of S = 14. In the second project we demonstrate a new synthetic route to purely inorganic-bridged, transition metal-azido clusters [CoII7 (4) and NiII7 (5)] and coordination polymers [{FeII/III2}n (6)] which exhibit strong ferromagnetic, SMM and long-range magnetic ordering behaviors. We also show that access to such a unique ferromagnetic class of inorganic, N-rich and O-free materials is feasible through the use of Me3SiN3 as the azido-ligand precursor without requiring the addition of any organic chelating/bridging ligand. In the last projects we have tried to bring together molecular magnetism and optics via the synthesis of multifunctional magnetic materials based on 3d- or 4f-metal ions. We decided to approach such challenge from two different directions: firstly, in our third project, by the deliberate replacement of non-emissive carboxylato ligands in known 3d-SMMs with their fluorescent analogues, without perturbing the metal-core structure and SMM properties (complexes 7, 8, and 9). The second route (last project) involves the use of naphthalene or pyridine-based polyalcohol bridging ligands for the synthesis of new polynuclear LnIII metal clusters (Ln = lanthanide) with novel topologies, SMM behaviors and luminescent properties arising from the increased efficiency of the “antenna” organic group. This approach has led us to the isolation of two new families of LnIII8 (complexes 10-13) and LnIII4 (complexes 14-20) clusters.

Influence de la phase d’usage dans les enjeux de la rénovation de bâtiments résidentiels écologiques : vers une approche diachronique

En Amérique du Nord, les pratiques actuelles de conception de l’industrie de la construction suscitent de nombreux et importants problèmes, tant au niveau environnemental, que social et économique. Certaines tendances conceptuelles, telles que l’industrialisation de la construction, le bâtiment vert, l’approche diachronique et la rationalisation spatiale proposent des moyens afin de répondre à cette problématique. La conception synchronique, qui ne se base encore que sur des besoins immédiats, produit des bâtiments statiques qui ne peuvent accommoder l’évolution des besoins. En plus de la phase d’usage qui se révèle la plus coûteuse en termes de consommation d’énergie, d’eau, de matériaux et de génération de déchets, le bâtiment statique est amené à subir de nombreuses rénovations, profondément délétères pour l’environnement et la situation économique des ménages. Dans une perspective d’opérationnalisation du développement durable, la problématique de recherche concerne la considération de la phase d’usage dans le processus conceptuel de l’habitation. Dans l’optique de favoriser une conception plutôt diachronique, 55 projets de rénovation résidentiels ont été analysés et comparés afin de décrire la nature et l’intensité des interventions effectuées. L’examen des plans avant/après rénovation a permis de quantifier le niveau d’intensité des interventions et ainsi, mettre en relief certaines tendances et récurrences des pratiques actuelles. Dans le but de valider si le bâtiment vert est en mesure de répondre aux enjeux environnementaux contemporains de l’habitation, les contenus de trois programmes de certification utilisés en Amérique du Nord, à savoir BOMA-BESt®, LEED®, et Living Building ChallengeTM, sont analysés. Une classification des stratégies proposées montre la répartition des préoccupations envers le bâtiment, les systèmes et l’usager. Une analyse permet de mettre en relief que les considérations semblent, de façon générale, cohérentes avec les impacts associés à l’habitation. Un examen plus ciblé sur la teneur et les objectifs des stratégies considérant l’usager permet l’émergence de deux ensembles thématiques : les cinq sources potentielles d’impacts (énergie, eau, matériaux, déchets et environnement intérieur), ainsi que les quatre thèmes reliés aux objectifs et aux finalités des stratégies (entretien et surveillance; sensibilisation et formation; modélisation et mesurage; comportement et habitude). La discussion a permis d’émettre des pistes d’écoconception pour permettre à l’habitation d’accommoder l’évolution des besoins des occupants, à savoir la « démontabilité », l’aptitude à l’évolution et l’accessibilité. Des recommandations, telles que la nécessité de mieux prendre en compte l’usager comme facteur d’influence des impacts occasionnés par la phase d’usage, sont ensuite proposées. D’autres suggestions appellent à une concrétisation de la performance en suscitant l’implication, l’engagement, la responsabilisation et l’autonomisation des occupants. Enfin, il semble que certaines modifications des programmes de certification et de la législation en vigueur pourraient favoriser l’émergence d’une vision nouvelle concernant la nécessaire réduction de la superficie habitable. Toutes ces opportunités d’amélioration ont le potentiel de mener ce secteur vers une démarche plus globale et systémique, tout en bonifiant de façon majeure les implications environnementales, économiques et sociales de l’habitation.

Sol-Gel Nanocrystalline Catalytic Titania Powders and Functional Coatings

In the present work Titania bulk powders and coatings were prepared by subjecting titanium isopropoxide solution to a controlled hydrolysis-condensation process. The powders were characterized using techniques such as FTIR for their chemical interactions, TG-DTA for the thermal decomposition features, XRD for the phase assemblage, BET specific surface area analysis for the textural features. The study discusses the preparation methods and the characterization techniques employed and a detailed discussion on the physico-chemical characterization of the prepared systems. The influence of dopants and leaching on the physico-chemical properties as well as their influence on photo activity is also included. The structural/functional coatings of different Titania compositions includes in this study. Coatings on pre-treated glass surfaces with the best compositions prepared showed 90 % transmittance in the visible region.

Radiopaque materials from natural polymers: Special emphasis on chitosan and natural rubber

The present work is to impart radiopacity in various natural polymers like chitosan, natural rubber and derivatives of chitosan and to characterize it. This thesis collated the radiopaque properties of these radiopaque polymers and various technological applications in the medical field. The applications of radiopaque polymers leads to an exploitation of radiopaque properties like X-ray visibility, optical density, effective atomic number, attenuation coefficient of biopolymers like chitosan, chitosan formate, chitosan acetate, carboxy methyl chitosan and natural rubber. The radiopaqe properties of these materials highly depend upon the size, shape, amount of radiopacifier and crystallinity of the radiopaque material. Radiopaque chitosan microspheres were prepared by cross linking with glutaraldehyde followed by the encapsulation of barium sulpahte. The effect of different emulsion systems on the morphology of chitosan microspheres were studied. The study concentrates radiopaque natural rubber for shielding applications. It reveals that to improve the particle size, morphology and crystalline phase of the zinc oxide particles, a novel method for the preparation of zinc oxide is adopted. A detailed radiopacity study was done in natural rubber containing 100phr precipitated zinc oxide prepared from different zinc salts. One of the significant findings of this investigation is that NR vulcanizates containing precipitated zinc oxide (from zinc acetate) shows higher attenuation coefficient. These interesting findings reveal the applications of these natural radiopaque systems in various fields like surgical tools, medical tubings, catheters, radiation shielding,etc.