Coastal engineering investigation at Jupiter Inlet, Florida

A fixed-bed hydraulic model of Jupiter Inlet, Florida, was constructed for the purpose of testing measures designed to remedy problems of sediment erosion and deposition in the inlet area. Both tide-induced flows as well as waves were simulated in the model which was built on an undistorted scale of 1:49. Model verification was based on prototype measurements of waves, tides and currents. Results have been interpreted in terms of the influence of various proposed remedial schemes on flow velocity magnitude, distribution and wave height at various locations within the study area. A stability parameter has been utilized for evaluating the degree of sediment erosion or deposition at a given location. Various structural solutions were examined in the model. It is proposed that, in the initial phase of solution implementation, sediment removal/nourishment methods be used primarily to mitigate the existing problems. New structures, as per model test results, should be installed under subsequent phases, only if sediment management procedures do not prove to be adequate. The currently followed procedure of periodic sand trap dredging may be extended to include the new dredging/nourishment requirements. (PDF contains 245 pages.)

Structural relaxation and chain dynamics in polymer melts : a computational investigation on the role of the intramolecular barriers

149 p. : il. col.

Investigation of High-Speed Combustible Gas Ignited by a Hot Gas Jet Produced in the Shock Tube

The high-speed combustible gas ignited by a hot gas jet, which is induced by shock focusing, was experimentally investigated. By use of the separation mode of shock tube, the test section of a single shock tube is split into two parts, which provide the high-speed flow of combustible gas and pilot flame of hot gas jet, respectively. In the interface of two parts of test sections the flame of jet was formed and spread to the high-speed combustible gas. Two kinds of the ignitions, 3-D "line-flame ignition" and 2-D "plane-flame ignition", were investigated. In the condition of 3-D "line-flame ignition" of combustion, thicker hot gas jet than pure air jet, was observed in schlieren photos. In the condition of 2-D "plane-flame ignition" of combustion, the delay time of ignition and the angle of flame front in schlieren photos were measured, from which the velocity of flame propagation in the high-speed combustible gas is estimated in the range of 30-90m/s and the delay time of ignition is estimated in the range of 0.12-0.29ms.

Numerical Simulation and Experimental Investigation about Internal and External Flows

In this paper, TASCflow3D is used to solve inner and outer 3D viscous incompressible turbulent flow (R-e = 5.6 X 10(6)) around axisymmetric body with duct. The governing equation is a RANS equation with standard k-epsilon turbulence model. The discrete method used is a finite volume method based on the finite element approach. In this method, the description of geometry is very flexible and at the same time important conservative properties are retained. The multi-block and algebraic multi-grid techniques are used for the convergence acceleration. Agreement between experimental results and calculation is good. It indicates that this novel approach can be used to simulate complex flow such as the interaction between rotor and stator or propulsion systems containing tip clearance and cavitation.

Investigation of Interactions between Two Monoclonal Antibodies and SARS Virus with a Label-Free Protein Array

The investigation of interactions between two kinds of monoclonal antibodies and SARS virus with a label-free protein array technique were presented in this paper. The performance consists of three parts: a surface modification for ligand immobilization/surface, a protein array fabrication with an integrated microfluidic system for patterning, packaging and liquid handling, and a protein array reader of imaging ellipsometer. This revealed the technique could be used as an immunoassay for qualitative and quantitative detection as wen as kinetic analysis of biomolecule interaction.

Investigation of Vaporized Kerosene Injection in a Supersonic Model Combustor

Characteristics of vaporized aviation kerosene injection in a supersonic model combustor were preliminarily investigated. The electrically storage type heater has a volume capacity of heating kerosene of 0.8 kg up to 670 K at a pressure of 5.5 Mpa. The temperature to cause pressurized kerosene jet being fully vaporized in Quiescent atmosphere was found to be 550 K at 4 Mpa however the pressurized hot kerosene remains in liquid state within the tube. The correspondent jet spray in Mach 2.5 vitiated air cross-flow were visualized by using stop schlieren photograph.It was found the penetration depth of the hot pressurized kerosene jet is approximately same with the temperature varied from 290 K to 550 k. at pressure of 4 Mpa. This results showed that the atomization process of hot kerosene jet spray in supersonic combustor could be bypassed and directly transferred to be gas state at temperature 550 K and pressure of 4 Mpa.