Experimental Characterization Of Electrical Current Leakage In Poly(Dimethylsiloxane) Microfluidic Devices

Poly(dimethylsiloxane) (PDMS) is usually considered as a dielectric material and the PDMS microchannel wall can be treated as an electrically insulated boundary in an applied electric field. However, in certain layouts of microfluidic networks, electrical leakage through the PDMS microfluidic channel walls may not be negligible, which must be carefully considered in the microfluidic circuit design. In this paper, we report on the experimental characterization of the electrical leakage current through PDMS microfluidic channel walls of different configurations. Our numerical and experimental studies indicate that for tens of microns thick PDMS channel walls, electrical leakage through the PDMS wall could significantly alter the electrical field in the main channel. We further show that we can use the electrical leakage through the PDMS microfluidic channel wall to control the electrolyte flow inside the microfluidic channel and manipulate the particle motion inside the microfluidic channel. More specifically, we can trap individual particles at different locations inside the microfluidic channel by balancing the electroosmotic flow and the electrophoretic migration of the particle.

Detailed experimental iced-storage characteristics of Barents Sea cod (Gadus morhua)

Im August 1997 wurde an Bord des FFS „Walther Herwig“ ein Eislagerversuch mit Kabeljau aus der Barebtssee durchgeführt. Die Fische wurden in täglichem Abstand auf ihre chemischen, physikalischen, sensorischen und mikrobiologischen Eigenschaften hin untersucht. Die analytischen Daten wurden jeweils mit den Tagen in Eis korreliert. Es erwies sich, daß die Werte vom Fischtester VI sowie RT Frischetester, von Dimethylamin- und Trimethylaminoxidstickstoff, die Qualitätseinstufung anhand des EUQualitätsbewertungsschemas, die sensorische Bewertung von gegarten Filetproben und die Gesamtkeimzahl auf der Haut am besten mit den im Eis verbrachten Tagen korrelierten. Die guteKorrelation zwischen sensorischen und instrumentell ermittelten Daten läßt in gewissem Umfang einen Ersatz von Sensorikdaten durch instrumentell ermittelten zu.

Experimental Demonstration Of A New Concept Of Drag Reduction And Thermal Protection For Hypersonic Vehicles

A new idea of drag reduction and thermal protection for hypersonic vehicles is proposed based on the combination of a physical spike and lateral jets for shock-reconstruction. The spike recasts the bow shock in front of a blunt body into a conical shock, and the lateral jets work to protect the spike tip from overheating and to push the conical shock away from the blunt body when a pitching angle exists during flight. Experiments are conducted in a hypersonic wind tunnel at a nominal Mach number of 6. It is demonstrated that the shock/shock interaction on the blunt body is avoided due to injection and the peak pressure at the reattachment point is reduced by 70% under a 4A degrees attack angle.

Experimental Study Of Multi-Hole Cooling For Integrally-Woven, Ceramic Matrix Composite Walls For Gas Turbine Applications

In this paper, multi-hole cooling is studied for an oxide/oxide ceramic specimen with normal injection holes and for a SiC/SiC ceramic specimen with oblique injection holes. A special purpose heat transfer tunnel was designed and built, which can provide a wide range of Reynolds numbers (10(5)similar to 10(7)) and a large temperature ratio of the primary flow to the coolant (up to 2.5). Cooling effectiveness determined by the measured surface temperature for the two types of ceramic specimens is investigated. It is found that the multi-hole cooling system for both specimens has a high cooling efficiency and it is higher for the SiC/SiC specimen than for the oxide/oxide specimen. Effects on the cooling effectiveness of parameters including blowing ratio, Reynolds number and temperature ratio, are studied. In addition, profiles of the mean velocity and temperature above the cooling surface are measured to provide further understanding of the cooling process. Duplication of the key parameters for multi-hole cooling, for a representative combustor flow condition (without radiation effects), is achieved with parameter scaling and the results show the high efficiency of multi-hole cooling for the oblique hole, SiC/SiC specimen. (C) 2008 Elsevier Ltd. All rights reserved.

Space experimental studies of microgravity fluid science in China

Microgravity fluid physics is an important part of microgravity sciences, which consists of simple fluids of many new systems, gas-liquid two-phase flow and heat transfer, and complex fluid mechanics. In addition to the importance of itself in sciences and applications, microgravity fluid physics closely relates to microgravity combustion, space biotechnology and space materials science, and promotes the developments of interdisciplinary fields. Many space microgravity experiments have been per- formed on board the recoverable satellites and space ships of China and pushed the rapid development of microgravity sciences in China. In the present paper, space experimental studies and the main re- sults of the microgravity fluid science in China in the last 10 years or so are introduced briefly.

Experimental Study on the Combined Evaporation Effect and Thermocapillary Convection in a Thin Liquid Layer

The coupling mechanisms and flow characteristics of thermocapillary convection in a thin liquid layer with evaporating interface were studied. The planar liquid layer, with the upper surface open to air, was imposed externally horizontal temperature differences. The measured average evaporating rates and interfacial temperature profiles indicated the relative importance of evaporation effect and thermocapillary convection under different temperature gradients. A temperature jump was found at the interface, which was thought to be related to the influence of evaporation effect. All above mentioned results were repeated in a rarely evaporating liquid to compare the influence of evaporation effect.

Experimental Study on the Ignition Process of Single Coal Particles at Microgravity

In this paper, the first Chinese microgravity (μ-g) experimental study on coal combustion was introduced. An experimental system used to study the ignition process of single coal particles was built up, complying with the requirements of the 3.5 s drop tower in the National Microgravity Laboratory of China (NMLC). High volatile bituminous and lignite coal particles with diameter of 1.5 and 2.0 mm were tested. The ignition and combustion process was recorded by a color CCD and the particle surface temperature before and at the ignition was determined by the RGB colorimetric method. Comparative experiments were conducted at normal gravity (1-g). The experiments revealed that at different gravity levels, the ignition of all tested coal particles commenced in homogeneous phase, while the shape, structure, brightness and development of the flames, as well as the volatile matter release during the ignition process are different. At μ-g, the part of volatile was released as a jet, while such a phenomenon was barely observed at 1-g. Also, after ignition, flames were more spherical, thicker, laminated and dimmer at μ-g. It was confirmed that ignition temperature decreased as the particle size or volatile content increased. However, contradicted to existing experimental results, provided other experimental conditions except gravity level were the same, ignition temperature of coal particles was about 50–80 K lower at μ-g than that at 1-g.

Experimental Research On Fatigue Property Of Steel Rubber Vibration Isolator For Offshore Jacket Platform In Cold Environment

Jacket platform is the most widely used offshore platform. Steel rubber vibration isolator and damping isolation system are often used to reduce or isolate the ice-induced and seismic-induced vibrations. The previous experimental and theoretical studies concern mostly with dynamic properties, vibration isolation schemes and vibration-reduction effectiveness analysis. In this paper, the experiments on steel rubber vibration isolator were carried out to investigate the compressive properties and fatigue properties in different low temperature conditions. The results may provide some guidelines for design of steel rubber vibration isolator for offshore platform in a cold environment, and for maintenance and replacement of steel rubber vibration isolator, and also for fatigue life assessment of the steel rubber vibration isolator. (C) 2009 Elsevier Ltd. All rights reserved.

Experimental Study Of Vortex-Induced Vibrations Of A Cylinder Near A Rigid Plane Boundary In Steady Flow

In this study, the vortex-induced vibrations of a cylinder near a rigid plane boundary in a steady flow are studied experimentally. The phenomenon of vortex-induced vibrations of the cylinder near the rigid plane boundary is reproduced in the flume. The vortex shedding frequency and mode are also measured by the methods of hot film velocimeter and hydrogen bubbles. A parametric study is carried out to investigate the influences of reduced velocity, gap-to-diameter ratio, stability parameter and mass ratio on the amplitude and frequency responses of the cylinder. Experimental results indicate: (1) the Strouhal number (St) is around 0.2 for the stationary cylinder near a plane boundary in the sub-critical flow regime; (2) with increasing gap-to-diameter ratio (e (0)/D), the amplitude ratio (A/D) gets larger but frequency ratio (f/f (n) ) has a slight variation for the case of larger values of e (0)/D (e (0)/D > 0.66 in this study); (3) there is a clear difference of amplitude and frequency responses of the cylinder between the larger gap-to-diameter ratios (e (0)/D > 0.66) and the smaller ones (e (0)/D < 0.3); (4) the vibration of the cylinder is easier to occur and the range of vibration in terms of V (r) number becomes more extensive with decrease of the stability parameter, but the frequency response is affected slightly by the stability parameter; (5) with decreasing mass ratio, the width of the lock-in ranges in terms of V (r) and the frequency ratio (f/f (n) ) become larger.

Experimental Study on the Responses of Bucket Foundations in Calcareous Sand under Vertical Dynamic Loading

Abstract: Experiments to determine the vertical static bearing capacity are carried out first in laboratory which is taken as a reference for choosing the amplitudes of vertical dynamic loading. Then a series of experiments are carried out to study the influences of factors, such as the scales of bucket, the amplitude and frequency of loading, the density of soils etc.. According to the experimental results, the responses of bucket foundations in calcareous sand under vertical dynamic loadings are analyzed. It is shown that there exists a limited effected zone under vertical dynamic loading. The scale of this zone is about one times of the bucket’s height. In this zone, the density of soil layer, the deformation and the pore pressure change obviously.

The hydrology of a small fish pond at the University of Agriculture, Makurdi Experimental Fish Farm

The monthly and seasonal water requirements of a small fish pond (0.068ha; maximum capacity of 613.83m super(3)) at the University of Agriculture, Makurdi Fish Farm (Benue, Nigeria) were determined during the period of February to August 1996. The sources of water for the pond were rainfall, (103.4cm), run-off (6.3cm) and regulated inflow (95.0cm). The water loss for the period were Evapotranspiration, (106.74cm), Seepage (71.64cm) and regulated discharge (25.00cm). Evapotranspiration was identified as the main source of water loss while rainfall was the major source of water gain. The mean monthly water deficit was 24.56~c11.43cm while the mean monthly surplus was 9.84~c8.05cm. The quantity of water required to maintain the optimal water level in the pond was 474.00m super(3). Preliminary water budget of the study area showed that rainfed aquaculture can be effectively carried out at Makurdi during the months of June to October with supplementary inflows during the dry season months

NUMERICAL AND EXPERIMENTAL STUDY ON LIQUID-SOLID FLOW IN A HYDROCYCLONE

Hydrocyclones are widely used in industry, of which the geometrical design using CFD techniques is gaining more popularity in recent years. In this study, the Euler-Euler approach and the Reynolds stress model are applied to simulate the liquid-solid flowfield in a hydrocyclone. The methodology is validated by a good agreement between experimental data and numerical results. Within the research range, the simulation indicates that the liquid-solid separation mainly occurs in the conical segment, and increasing conical height or decreasing cylindrical height helps to improve the grade efficiencies of solid particles. Based on these results, two of the same hydrocyclones are designed and installed in series to establish a liquid-solid separation system. Many experiments are then conducted under different conditions, in which the effects of the water cut and the second hydrocyclone on the separation are investigated. The results also confirm that smaller solid particles are more susceptible to the inlet conditions, and the second hydrocyclone plays a more important role as the water cut reduces.