Designing for production,

Authors' names in reverse order in 1957 edition.

Field trial of a new aeration system for enhancing biodegradation in a biopile

The influence of a new aeration system on the biopile performance was investigated. The purpose was to increase biodegradation efficiency by optimising airflow through the pile. During a 1-month field trial, the performance of a new system using two perforated vertical pipes with wind-driven turbines was compared with that of a standard pile configuration with two horizontal perforated pipes. Both piles were composed of a similar mix of diesel-contaminated soils, woodchips, compost and NPK fertiliser. Hydrocarbons were recovered using solvent extraction, and determined both gravimetrically and by gas chromatography. Total heterotrophs, pH and moisture content were also assessed. Air pressure measurements were made to compare the efficiency of suction in the pipes. Results at the end of the experiment showed that there was no significant difference between the two piles in the total amount of hydrocarbon biodegradation. The normalised degradation rate was, however, considerably higher in the new system than in the standard one, suggesting that the vertical venting method may have improved the efficiency of the biological reactions in the pile. The pressure measurements showed a significant improvement in the suction produced by the new aeration system. However, many factors other than the airflow (oxygen supply) may influence and limit the biodegradation rates, including moisture content, age of contaminants and the climatic conditions. Additional experiments and modelling need to be carried out to explore further the new aeration method and to develop criteria and guidelines for engineering design of optimal aeration schemes in order to achieve maximum biodegradation in biopiles. (C) 2003 Elsevier Ltd. All rights reserved.

Characterizing the physical and chemical properties of a vermicompost filter bed

Vermicompost filtration is a new on-site waste treatment system. Consequently, little is known about the filter medium properties. The aim of this preliminary study was to quantify physical and compositional properties of vermicompost filter beds that had been used to treat domestic solid organic waste and wastewater. This paper presents the trials performed on pilot-scale reactors filled with vermicompost from a full-scale vermicompost filtration system. Household solid organic waste and raw wastewater at the rate of 130 L/m(2)/d was applied to the reactor bed surface over a four-month period. It was found that fresh casts laid on the bed surface had a BOD of 1290 mg/g VS while casts buried to a depth of 10 cm had a BOD of 605 mg/g VS. Below this depth there was little further biodegradation of earthworm casts despite cast ages of up to five years. Solid material in the reactor accounted for only 7-10% of the reactor volume. The total voidage comprised of large free-draining pores, which accounted for 15-20% of the reactor volume and 60-70% micropores, able to hold up water against gravity. It was shown that water could flow through the medium micropores and macropores following a wastewater application. The wastewater flow characteristics were modeled by a two-region model based on the Richards Equation, an equation used to describe porous spatially heterogeneous materials.

Interference between propagating changes and its effect on system failure

Computer-based, socio-technical systems projects are frequently failures. In particular, computer-based information systems often fail to live up to their promise. Part of the problem lies in the uncertainty of the effect of combining the subsystems that comprise the complete system; i.e. the system's emergent behaviour cannot be predicted from a knowledge of the subsystems. This paper suggests uncertainty management is a fundamental unifying concept in analysis and design of complex systems and goes on to indicate that this is due to the co-evolutionary nature of the requirements and implementation of socio-technical systems. The paper shows a model of the propagation of a system change that indicates that the introduction of two or more changes over time can cause chaotic emergent behaviour.

Applications of Reissner's principle to structural dynamics

The analysis and prediction of the dynamic behaviour of s7ructural components plays an important role in modern engineering design. :n this work, the so-called "mixed" finite element models based on Reissnen's variational principle are applied to the solution of free and forced vibration problems, for beam and :late structures. The mixed beam models are obtained by using elements of various shape functions ranging from simple linear to complex cubic and quadratic functions. The elements were in general capable of predicting the natural frequencies and dynamic responses with good accuracy. An isoparametric quadrilateral element with 8-nodes was developed for application to thin plate problems. The element has 32 degrees of freedom (one deflection, two bending and one twisting moment per node) which is suitable for discretization of plates with arbitrary geometry. A linear isoparametric element and two non-conforming displacement elements (4-node and 8-node quadrilateral) were extended to the solution of dynamic problems. An auto-mesh generation program was used to facilitate the preparation of input data required by the 8-node quadrilateral elements of mixed and displacement type. Numerical examples were solved using both the mixed beam and plate elements for predicting a structure's natural frequencies and dynamic response to a variety of forcing functions. The solutions were compared with the available analytical and displacement model solutions. The mixed elements developed have been found to have significant advantages over the conventional displacement elements in the solution of plate type problems. A dramatic saving in computational time is possible without any loss in solution accuracy. With beam type problems, there appears to be no significant advantages in using mixed models.

Development of science and technology policy for Kuwait

The status of Science and Technology in KUWAIT has been analysed in order to assess the extent of the application of Science and Technology needed for the Country's development. The design and implementation of a Science and Technology Policy has been examined to identify the appropriate technology necessary to improve KUWAIT's socio-economic-industrial structures. Following a general and critical review of the role of Science and Technology in the developing countries, the author has reviewed the past and contemporary employment of Science and Technology for development.of various sectors and the existence, if any, of any form (explicit, implicit, or both) of a Science and Technology Policy in KUWAIT. The thesis is structured to evaluate almost all of the sectors in KUWAIT which utilise Science and/or Technology, the effectiveness of such practices, their policymaking process, the channels by which policies were transformed into sources of influence through Governmental action and the impact that various policy instruments at the disposal of the the Government had on the development of S & T capabilities. The author has studied the implications of the absence of a Science and Technology Policy in Kuwait by examining some specific case studies, eg, the absence of a Technology Assessment Process and the negative impacts resulting from this; the ad-hoc allocation of the research and development budget instead of its being based on a percentage of GNP; the limitations imposed on the development of indigenous contracting companies and consultancy and engineering design offices; the impacts of the absence of Technology Transfer Centre, and so forth. As a consequence of the implications of the above studies, together with the negative results from the absence of an explicit Science and Technology Policy, eg, research and development activities do not relate to the national development plans, the author suggests that a Science and Technology Policy-Making Body should be established to formulate, develop, monitor and correlate the Science and Technology Activities in KUWAIT.

Today's pupils tomorrow's engineers! Pedagogy and policy:a UK perspective

Purpose – This paper aims to provide a critical analysis of UK Government policy in respect of recent moves to attract young people into engineering. Drawing together UK and EU policy literature, the paper considers why young people fail to look at engineering positively. Design/methodology/approach – Drawing together UK policy, practitioner and academic-related literature the paper critically considers the various factors influencing young people's decision-making processes in respect of entering the engineering profession. A conceptual framework providing a diagrammatic representation of the “push” and “pull” factors impacting young people at pre-university level is given. Findings – The discussion argues that higher education in general has a responsibility to assist young people overcome negative stereotypical views in respect of engineering education. Universities are in the business of building human capability ethically and sustainably. As such they hold a duty of care towards the next generation. From an engineering education perspective, the major challenge is to present a relevant and sustainable learning experience that will equip students with the necessary skills and competencies for a lifelong career in engineering. This may be achieved by promoting transferable skills and competencies or by the introduction of a capabilities-driven curriculum which brings together generic and engineering skills and abilities. Social implications – In identifying the push/pull factors impacting young people's decisions to study engineering, this paper considers why, at a time of global recession, young people should select to study the required subjects of mathematics, science and technology necessary to study for a degree in engineering. The paper identifies the long-term social benefits of increasing the number of young people studying engineering. Originality/value – In bringing together pedagogy and policy within an engineering framework, the paper adds to current debates in engineering education providing a distinctive look at what seems to be a recurring problem – the failure to attract young people into engineering.

An interdisciplinary approach to designing and evaluating a hybrid solar-biomass power plant

Purpose: Energy security is a major concern for India and many rural areas remain un-electrified. Thus, innovations in sustainable technologies to provide energy services are required. Biomass and solar energy in particular are resources that are widely available and underutilised in India. This paper aims to provide an overview of a methodology that was developed for designing and assessing the feasibility of a hybrid solar-biomass power plant in Gujarat. Design/methodology/approach: The methodology described is a combination of engineering and business management studies used to evaluate and design solar thermal collectors for specific applications and locations. For the scenario of a hybrid plant, the methodology involved: the analytical hierarchy process, for solar thermal technology selection; a cost-exergy approach, for design optimisation; quality function deployment, for designing and evaluating a novel collector - termed the elevation linear Fresnel reflector (ELFR); and case study simulations, for analysing alternative hybrid plant configurations. Findings: The paper recommended that for a hybrid plant in Gujarat, a linear Fresnel reflector of 14,000 m2 aperture is integrated with a 3 tonne per hour biomass boiler, generating 815 MWh per annum of electricity for nearby villages and 12,450 tonnes of ice per annum for local fisheries and food industries. However, at the expense of a 0.3 ¢/kWh increase in levelised energy costs, the ELFR can increase savings of biomass (100 t/a) and land (9 ha/a). Research limitations/implications: The research reviewed in this paper is primarily theoretical and further work will need to be undertaken to specify plant details such as piping layout, pump sizing and structure, and assess plant performance during real operational conditions. Originality/value: The paper considers the methodology adopted proved to be a powerful tool for integrating technology selection, optimisation, design and evaluation and promotes interdisciplinary methods for improving sustainable engineering design and energy management. © Emerald Group Publishing Limited.

Using genetic programming and decision trees for generating structural descriptions of four bar mechanisms

Four bar mechanisms are basic components of many important mechanical devices. The kinematic synthesis of four bar mechanisms is a difficult design problem. A novel method that combines the genetic programming and decision tree learning methods is presented. We give a structural description for the class of mechanisms that produce desired coupler curves. Constructive induction is used to find and characterize feasible regions of the design space. Decision trees constitute the learning engine, and the new features are created by genetic programming.

EpiDOCK:a molecular docking-based tool for MHC class II binding prediction

Cellular peptide vaccines contain T-cell epitopes. The main prerequisite for a peptide to act as a T-cell epitope is that it binds to a major histocompatibility complex (MHC) protein. Peptide MHC binder identification is an extremely costly experimental challenge since human MHCs, named human leukocyte antigen, are highly polymorphic and polygenic. Here we present EpiDOCK, the first structure-based server for MHC class II binding prediction. EpiDOCK predicts binding to the 23 most frequent human, MHC class II proteins. It identifies 90% of true binders and 76% of true non-binders, with an overall accuracy of 83%. EpiDOCK is freely accessible at http://epidock.ddg-pharmfac. net. © The Author 2013. Published by Oxford University Press. All rights reserved.

Guest editorial:special issue on digitial enterprise technology

Full text This Proceedings volume contains selected papers from the Fourth International CIRP-sponsored, Conference on Digital Enterprise Technology (DET2007), which was held at the University of Bath, UK, 19–21 September 2007. All selected papers have been suitably enhanced for publication in the Journal and have undergone full review. Digital enterprise technology (DET) is ‘the collection of systems and methods for the digital modelling and analysis of the global product development and realization process, in the context of lifecycle management.’ The principal aim of the DET concept is to provide a coherent context for the development and integration of the various digital technologies that underpin modern design and manufacturing. These technologies can be classified according to the following five key areas. 1. Distributed and collaborative design. 2. Process modelling and process planning. 3. Advanced factory design and modelling. 4. Physical-to-digital environment integrators–verification. 5. Enterprise integration technologies. This special issue is representative of the wide breadth of the DET concept including; a comprehensive review of digital engineering, design processes, digital modelling of machine tools, forming, robotics and machining processes, verification and metrology, and dynamic networks. It is particularly pleasing to see the development of metrology as a key aspect of modern manufacturing technology, linking design intent to process capability. The papers published herein will facilitate the exploration of new and evolving research concepts by the international research community and will influence the development of international standards for the application of DET technologies.