Measurement of the mechanical power of walking by satellite positioning system (GPS).

PURPOSE: This descriptive article illustrates the application of Global Positioning System (GPS) professional receivers in the field of locomotion studies. The technological challenge was to assess the external mechanical work in outdoor walking. METHODS: Five subjects walked five times during 5 min on an athletic track at different imposed stride frequency (from 70-130 steps x min(-1)). A differential GPS system (carrier phase analysis) measured the variation of the position of the trunk at 5 Hz. A portable indirect calorimeter recorded breath-by-breath energy expenditure. RESULTS: For a walking speed of 1.05 +/- 0.11 m x s(-1), the vertical lift of the trunk (43 +/- 14 mm) induced a power of 46.0 +/- 20.4 W. The average speed variation per step (0.15 +/- 0.03 m x s(-1)) produced a kinetic power of 16.9 +/- 7.2 W. As compared with commonly admitted values, the energy exchange (recovery) between the two energy components was low (39.1 +/- 10.0%), which induced an overestimated mechanical power (38.9 +/- 18.3 W or 0.60 W x kg(-1) body mass) and a high net mechanical efficiency (26.9 +/- 5.8%). CONCLUSION: We assumed that the cause of the overestimation was an unwanted oscillation of the GPS antenna. It is concluded that GPS (in phase mode) is now able to record small body movements during human locomotion, and constitutes a promising tool for gait analysis of outdoor unrestrained walking. However, the design of the receiver and the antenna must be adapted to human experiments and a thorough validation study remains to be conducted.

Fly Ash Soil Stabilization for Non-Uniform Subgrade Soils, Volume I: Engineering Properties and Construction Guidelines, TR-461, 2005

Soil treated with self-cementing fly ash is increasingly being used in Iowa to stabilize fine-grained pavement subgrades, but without a complete understanding of the short- and long-term behavior. To develop a broader understanding of fly ash engineering properties, mixtures of five different soil types, ranging from ML to CH, and several different fly ash sources (including hydrated and conditioned fly ashes) were evaluated. Results show that soil compaction characteristics, compressive strength, wet/dry durability, freeze/thaw durability, hydration characteristics, rate of strength gain, and plasticity characteristics are all affected by the addition of fly ash. Specifically, Iowa selfcementing fly ashes are effective at stabilizing fine-grained Iowa soils for earthwork and paving operations; fly ash increases compacted dry density and reduces the optimum moisture content; strength gain in soil-fly ash mixtures depends on cure time and temperature, compaction energy, and compaction delay; sulfur contents can form expansive minerals in soil–fly ash mixtures, which severely reduces the long-term strength and durability; fly ash increases the California bearing ratio of fine-grained soil–fly ash effectively dries wet soils and provides an initial rapid strength gain; fly ash decreases swell potential of expansive soils; soil-fly ash mixtures cured below freezing temperatures and then soaked in water are highly susceptible to slaking and strength loss; soil stabilized with fly ash exhibits increased freeze-thaw durability; soil strength can be increased with the addition of hydrated fly ash and conditioned fly ash, but at higher rates and not as effectively as self-cementing fly ash. Based on the results of this study, three proposed specifications were developed for the use of self-cementing fly ash, hydrated fly ash, and conditioned fly ash. The specifications describe laboratory evaluation, field placement, moisture conditioning, compaction, quality control testing procedures, and basis of payment.

Re-Engineering CTE in Iowa: Aligning Career and Technical Education Reform, Workforce Development and Economic Development, August 2007

Iowa is a relatively small state and is on the rebound economically. It has an overall population that is stable, but which is shifting within the state from more rural areas to suburban and urban centers. There is a very tight labor market with high levels of employment. Iowa now has a time-sensitive opportunity to exert global leadership in renewable energy, while maintaining its leadership in other key industries like finance and agriculture.

Major mite allergen Der f 1 concentration is reduced in buildings with improved energy performance.

BACKGROUND: Environmental conditions play a crucial role in mite growth, and optimal environmental control is key in the prevention of airway inflammation in chronic allergic rhinoconjunctivitis or asthma. OBJECTIVE: To evaluate the relationship between building energy performance and indoor mite allergen concentration in a cross-sectional study. METHODS: Major allergen concentration (Der f 1, Der p 1, mite group 2, Fel d 1 and Bla g 2) was determined by quantitative dot blot analysis from mattress and carpet dust samples in five buildings designed for low energy use (LEB) and in six control buildings (CB). Inhabitants had received 4 weeks prior to mite measurement a personal validated questionnaire related to the perceived state of health and comfort of living. RESULTS: Cumulative mite allergen concentration (with Der f 1 as the major contributor) was significantly lower in LEB as compared with CB both in mattresses and in carpets. In contrast, the two categories of buildings did not differ in Bla g 2 and Fel d 1 concentration, in the amount of dust and airborne mould collected. Whereas temperature was higher in LEB, relative humidity was significantly lower than in CB. Perceived overall comfort was better in LEB. CONCLUSIONS: Major mite allergen Der f 1 preferentially accumulates in buildings not specifically designed for low energy use, reaching levels at risk for sensitization. We hypothesize that controlled mechanical ventilation present in all audited LEB may favour lower air humidity and hence lower mite growth and allergen concentration, while preserving optimal perceived comfort.

Puunkäsittelykoneen simulointi ja mekaaniset häviöt

Diplomityö on osa Savonia-amk:n koneosaston TOVI-projektia, jossa metsä-konevalmistaja Ponsse Oyj on mukana. Työssä tutkittiin Ponsse Oyj:n metsäkoneen harvesteripäätä. Tavoitteena oli harvesteripään puun syöttöliikkeessä syntyvien mekaanisten häviöiden selvittäminen. Mekaanisilla häviöillä tarkoitamme karsintaterien kitkavoimia ja syöttörullien vierintävastusta.Edellisten lisäksi tavoitteena oli tutkia puun syöttöliikkeen simuloitavuutta monikappaledynamiikkaan perustuvalla simu-lointiohjelmistolla. Työ toteutettiin mittaamalla harvesteripään hydraulisten toimilaitteiden paineita, puun syötön aikana. Mittasimme myös puun ja harvesteripään välistä liikematkaa, nopeutta, kiihtyvyyttä, sekä puun paksuutta. Mittausten lisäksi harvesteripäästä rakennettiin simulointimalli. Mitattujen paineiden avulla laskettiin vastaavien toimilaitteiden synnyttämät voimat ja momentit. Simulointimallilla toistettiin mittaustapahtumat, käyttäen mittausten avulla laskettuja voimia ja momentteja. Mallin kitkakertoimien ja vierintävastusten avulla simuloidut ja mitatut liikematkat haettiin yhteneviksi. Toisin sanoen, simulointimalli verifioitiin todellisuutta vastaavaksi, jolloin simulointimallista voitiin lukea syntyneet häviöt.

Optimal Mechanical PulpingProcesses for Eucalyptus, Acacia and Birch

Tässä diplomityössä tutkittiin ja vertailtiin eukalyptuksen, akaasian ja koivun kemimekaanista kuiduttamista ja valkaisua. Yleensä näitä puulajeja käytetään sellun keittoon. Puulajit eroavat toisistaan kasvupaikan ja kuiturakenteen osalta. Eukalyptus ja akaasia ovat niin sanottuja trooppisia lehtipuita, kun taas koivu kasvaa pohjoisilla vyöhykkeillä. Koivulla on kookkaimmat kuidut ja akaasialla pienimmät kuidut. Myös näiden lajien putkilot eroavat toisistaan. Koivun putkilot ovat pitkiä ja kapeita, kun taas eukalyptuksen ja akaasian putkilot ovat lyhyitä ja leveitä. Prosessiksi valittiin kaksivaiheinen APMP-prosessi. Koeajot tehtiinKeskuslaboratorio Oy:ssä. Massoille asetettiin seuraavat tavoitteet: freeness 150-200 ml ja vaaleus 80 %ISO. Eukalyptukselle ja koivulle tehtiin kaksi erilaista impregnointisarjaa, mutta akaasialle vain yksi. Jauhatuksen viimeisessä vaiheessa kokeiltiin myös jauhinvalkaisua. Jauhatuksen energiankulutus oli korkea varsinkin eukalyptuksella ja akaasialla. Jotta energiankulutus saataisiin pienemmäksi, tulisi käyttää enemmän lipeää, mutta se johtaa alkalitummumiseen. Lopuksi massat valkaistiin laboratoriossa. Eukalyptus ja koivu pystyttiin valkaisemaan vaaleuteen 80 %ISO, mutta eukalyptuksen valkaisu vaati enemmän peroksidia kuin koivun valkaisu. Akaasian lähtövaaleus oli niin alhainen, ettei siinä päästy tavoitevaaleuteen. Eukalyptuksella on parempi valonsironta ja paremmat lujuusominaisuudet kuin koivulla. Kemimekaanista massaa voidaan käyttää hienopaperissa parantamassa jäykkyyttä, bulkkia ja valonsirontaa, mutta usein ongelmana on alhainen vaaleus ja huono vaaleuden pysyvyys. Kemimekaanista massaa voidaankäyttää missä tahansa mekaanisissa painopapereissa. Mekaanisissa painopapereissa kemimekaanisella lehtipuumassalla voidaan korvata mekaanista havupuumassaa. Akaasia on niin tummaa, ettei sitä voida käyttää korkeavaaleuksisiin papereihin. Eukalyptus ja koivu ovat vaaleampia ja helpompia valkaista kuin akaasia, mutta myös niillä on niin huono vaaleudenpysyvyys että käyttö hienopapereissa on rajoittunutta. Mekaanisille eukalyptus ja koivumassoille hienopaperia parempi käyttökohde on mekaaniset painopaperit, kuten MWC-paperi.

Effect of Mechanical and Geometric Mismatching on Fatigue and Damage of Welded Joints

The future of high technology welded constructions will be characterised by higher strength materials and improved weld quality with respect to fatigue resistance. The expected implementation of high quality high strength steel welds will require that more attention be given to the issues of crack initiation and mechanical mismatching. Experiments and finite element analyses were performed within the framework of continuum damage mechanics to investigate the effect of mismatching of welded joints on void nucleation and coalescence during monotonic loading. It was found that the damage of undermatched joints mainly occurred in the sandwich layer and the damageresistance of the joints decreases with the decrease of the sandwich layer width. The damage of over-matched joints mainly occurred in the base metal adjacent to the sandwich layer and the damage resistance of the joints increases with thedecrease of the sandwich layer width. The mechanisms of the initiation of the micro voids/cracks were found to be cracking of the inclusions or the embrittled second phase, and the debonding of the inclusions from the matrix. Experimental fatigue crack growth rate testing showed that the fatigue life of under-matched central crack panel specimens is longer than that of over-matched and even-matched specimens. Further investigation by the elastic-plastic finite element analysis indicated that fatigue crack closure, which originated from the inhomogeneousyielding adjacent to the crack tip, played an important role in the fatigue crack propagation. The applicability of the J integral concept to the mismatched specimens with crack extension under cyclic loading was assessed. The concept of fatigue class used by the International Institute of Welding was introduced in the parametric numerical analysis of several welded joints. The effect of weld geometry and load condition on fatigue strength of ferrite-pearlite steel joints was systematically evaluated based on linear elastic fracture mechanics. Joint types included lap joints, angle joints and butt joints. Various combinations of the tensile and bending loads were considered during the evaluation with the emphasis focused on the existence of both root and toe cracks. For a lap joint with asmall lack-of-penetration, a reasonably large weld leg and smaller flank angle were recommended for engineering practice in order to achieve higher fatigue strength. It was found that the fatigue strength of the angle joint depended strongly on the location and orientation of the preexisting crack-like welding defects, even if the joint was welded with full penetration. It is commonly believed that the double sided butt welds can have significantly higher fatigue strength than that of a single sided welds, but fatigue crack initiation and propagation can originate from the weld root if the welding procedure results in a partial penetration. It is clearly shown that the fatigue strength of the butt joint could be improved remarkably by ensuring full penetration. Nevertheless, increasing the fatigue strength of a butt joint by increasing the size of the weld is an uneconomical alternative.

Lappeenrannan teknillisen yliopiston opiskelijoiden yrittäjyyshalukkuus, yrittäjyyssopivuus ja opintomenestys

The aim of this thesis was to clarify willingness and suitability for entrepreneurship among students of Lappeenranta University of Technology (LUT). In addition factors that would explain academic achievement and if there were relationship between academic achievement and willingness or suitability for entrepreneurship were examined. Questionnaires were sent via e-mail to 800 students of LUT in summer 2007. Response percent was 29,6 %. Based on the collected answers factors of entrepreneurial motivation and academic achievement were analyzed using mainly Pearson’s correlation coefficient and factor analysis. In the light of these factors willingness and suitability for entrepreneurship and academic achievement were examined. The results indicated that 36,7 % of the respondents were willing and 11,4 % were suitable for entrepreneurship. The largest share of the willing ones was focused on Department of Mechanical Engineering, whereas the smallest share on Department of Environmental Technology. The largest shares of the suitable ones were on Departments of Mechanical and Electrical Engineering, and the smallest shares on Departments of Environmental, Chemical and Energy Technology. Academic achievement was affected by, among others, exercising and success in high school. Academic achievement and willingness or suitability for entrepreneurship didn’t correlate. Yet, from factors of entrepreneurial motivation internal locus of control correlated positively with academic achievement.

Influence of process parameters on part quality and mechanical properties for DMLS and SLM with iron-based materials

Rapid manufacturing is an advanced manufacturing technology based on layer-by-layer manufacturing to produce a part. This paper presents experimental work carried out to investigate the effects of scan speed, layer thickness, and building direction on the following part features: dimensional error, surface roughness, and mechanical properties for DMLS with DS H20 powder and SLM with CL 20 powder (1.4404/AISI 316L). Findings were evaluated using ANOVA analysis. According to the experimental results, build direction has a significant effect on part quality, in terms of dimensional error and surface roughness. For the SLM process, the build direction has no influence on mechanical properties. Results of this research support industry estimating part quality and mechanical properties before the production of parts with additive manufacturing, using iron-based powders

How much protein and energy are needed to equilibrate nitrogen and energy balances in ventilated critically ill children?

BACKGROUND & AIMS: Protein and energy requirements in critically ill children are currently based on insufficient data. Moreover, longitudinal measurements of both total urinary nitrogen (TUN) and resting energy expenditure (REE) are lacking. The aim of this study was to investigate how much protein and energy are needed to equilibrate nitrogen and energy balances in ventilated critically ill children on the basis of daily measurements of TUN, REE and protein and energy intakes. Comparisons were made with the guidelines of the American Society for Parenteral and Enteral Nutrition and the Dietary Reference Intakes. METHODS: Children with an expected duration of mechanical ventilation ≥72 h were prospectively recruited. TUN was measured by chemiluminescence, and REE was measured by indirect calorimetry. Generalised linear models for longitudinal data were used to study the relation between protein intake and nitrogen balance and to calculate the minimum intake of protein needed to achieve nitrogen equilibrium. A similar approach was used for energy. Results were compared to the recommended values. RESULTS: Based on 402 measurements performed in 74 children (median age: 21 months), the mean TUN was high at 0.20 (95% CI: 0.20, 0.22) g/kg/d and the REE was 55 (95% CI: 54, 57) kcal/kg/d. Nitrogen and energy balances were achieved with 1.5 (95% CI: 1.4, 1.6) g/kg/d of protein and 58 (95% CI: 53, 63) kcal/kg/d for the entire group, but there were differences among children of different ages. Children required more protein and less energy than the Dietary Reference Intakes. CONCLUSIONS: In critically ill children, TUN was elevated and REE was reduced during the entire period of mechanical ventilation. Minimum intakes of 1.5 g/kg/d of protein and 58 kcal/kg/d can equilibrate nitrogen and energy balances in children up to 4 years old. Older children require more protein.

Mechanical Design of Hydraulic Vise

The general task of clamping devise is to connect the parts to the machining centers so that the work piece could be fixed on its position during the whole machining process. Additionally, the work piece should be clamped easily and rapidly by the machine users. The purpose of this Master’s thesis project was to develop a product design and find out the dimensioning of a hydraulic vise system for Astex Engineering OY, which was taking care of the general principles of product design and development during the design process. Throughout the process, the needs of manufacturing and assembling were taken into consideration for the machinability and minimization of the cost of manufacturing. The most critical component of the clamping devise was modeled by FEM for the issue of strength requirements. This 3D model was created with Solidworks and FEM-analysis was done with Cosmos software. As the result of this design work, a prototype of the hydraulic vise was manufactured for Astex Engineering OY and the practical test.

DFM/DFMA(A) – analysis and aspects of applying systematic engineering for a microwave testfixture design

In this paper, manufacturability analysis and collection of design aspects is made for a microwave test-fixture. Aspects of applying systematic design for a microwave test-fixture design and manufacturing are also analysed. Special questionnaires for the component and machining are made in order to enable necessary information to ensure DFM(A) – aspects of the component. The aspects of easy manufacturing for machining the microwave test-fixture are collected. Material selection is discussed and manufacturing stages of prototype manufacturing are presented.

Utilisation of biomass for energy production in the North-West Russian forest industry

Traditionally, fossil fuels have always been the major sources of the modern energy production. However prices on these energy sources have been constantly increasing. The utilization of local biomass resources for energy production can substitute significant part of the required energy demand in different energy sectors. The introduction of the biomass usage can easily be started in the forest industry first as it possesses biomass in a large volume. The forest industry energy sector has the highest potential for the fast bioenergy development in the North-West Russia. Therefore, the question concerning rational and effective forest resources use is important today as well as the utilization of the forestry by-products. This work describes and analyzes the opportunities of utilising biomass, mainly, in the form of the wood by-products, for energy production processes in general, as well as for the northwest Russian forest industry conditions. The study also covers basic forest industry processes and technologies, so, the reader can get familiar with the information about the specific character of the biomass utilization. The work gives a comprehensive view on the northwest forest industry situation from the biomass utilisation point of view. By presenting existing large-scale sawmills and pulp and paper mills the work provides information for the evaluation of the future development of CHP investments in the northwest Russian forest industry.

Technical Wind Energy Potential in Russia

The goal of the master's thesis is a detailed research of the technical wind energy potential in Russian Federation: the distribution of the potential all over the territory of the country and the possibility of the application of the potential for power supply of various objects. The main attention of the thesis is devoted to the assessment of wind energy resources (potential) of Russian Federation, both for the territory of country in whole and for every region. Theoretical basic wind energy concepts and the scheme of transformation of kinetic energy of a wind into electric energy by modern wind turbines are given in the work. Also the costs of energy, stimuli of development of wind-engineering and obstacles which impact the industry development are analyzed. The review of existent and projected wind power plants in Russia is carried out.