Multiscale Characterization of Acrylic Bone Cement Modified with Functionalized Mesoporous Silica Nanoparticles

Acrylic bone cement is widely used to anchor orthopedic implants to bone and mechanical failure of the cement mantle surrounding an implant can contribute to aseptic loosening. In an effort to enhance the mechanical properties of bone cement, a variety of nanoparticles and fibers can be incorporated into the cement matrix. Mesoporous silica nanoparticles (MSNs) are a class of particles that display high potential for use as reinforcement within bone cement. Therefore, the purpose of this study was to quantify the impact of modifying an acrylic cement with various low-loadings of mesoporous silica. Three types of MSNs (one plain variety and two modified with functional groups) at two loading ratios (0.1 and 0.2 wt/wt) were incorporated into a commercially available bone cement. The mechanical properties were characterized using four-point bending, microindentation and nanoindentation (static, stress relaxation, and creep) while material properties were assessed through dynamic mechanical analysis, differential scanning calorimetry, thermogravimetric analysis, FTIR spectroscopy, and scanning electron microscopy. Four-point flexural testing and nanoindentation revealed minimal impact on the properties of the cements, except for several changes in the nano-level static mechanical properties. Conversely, microindentation testing demonstrated that the addition of MSNs significantly increased the microhardness. The stress relaxation and creep properties of the cements measured with nanoindentation displayed no effect resulting from the addition of MSNs. The measured material properties were consistent among all cements. Analysis of scanning electron micrographs images revealed that surface functionalization enhanced particle dispersion within the cement matrix and resulted in fewer particle agglomerates. These results suggest that the loading ratios of mesoporous silica used in this study were not an effective reinforcement material. Future work should be conducted to determine the impact of higher MSN loading ratios and alternative functional groups. (C) 2014 Elsevier Ltd. All rights reserved.

Carbon dioxide sequestration in cement kiln dust through miner carbonation

The feasibility of carbon sequestration in cement kiln dust (CKD) was investigated in a series of batch and column experiments conducted under ambient temperature and pressure conditions. The significance of this work is the demonstration that alkaline wastes, such as CKD, are highly reactive with carbon dioxide (CO2). In the presence of water, CKD can sequester greater than 80% of its theoretical capacity for carbon without any amendments or modifications to the waste. Other mineral carbonation technologies for carbon sequestration rely on the use of mined mineral feedstocks as the source of oxides. The mining, pre-processing and reaction conditions needed to create favorable carbonation kinetics all require significant additions of energy to the system. Therefore, their actual net reduction in CO2 is uncertain. Many suitable alkaline wastes are produced at sites that also generate significant quantities of CO2. While independently, the reduction in CO2 emissions from mineral carbonation in CKD is small (~13% of process related emissions), when this technology is applied to similar wastes of other industries, the collective net reduction in emissions may be significant. The technical investigations presented in this dissertation progress from proof of feasibility through examination of the extent of sequestration in core samples taken from an aged CKD waste pile, to more fundamental batch and microscopy studies which analyze the rates and mechanisms controlling mineral carbonation reactions in a variety of fresh CKD types. Finally, the scale of the system was increased to assess the sequestration efficiency under more pilot or field-scale conditions and to clarify the importance of particle-scale processes under more dynamic (flowing gas) conditions. A comprehensive set of material characterization methods, including thermal analysis, Xray diffraction, and X-ray fluorescence, were used to confirm extents of carbonation and to better elucidate those compositional factors controlling the reactions. The results of these studies show that the rate of carbonation in CKD is controlled by the extent of carbonation. With increased degrees of conversion, particle-scale processes such as intraparticle diffusion and CaCO3 micropore precipitation patterns begin to limit the rate and possibly the extent of the reactions. Rates may also be influenced by the nature of the oxides participating in the reaction, slowing when the free or unbound oxides are consumed and reaction conditions shift towards the consumption of less reactive Ca species. While microscale processes and composition affects appear to be important at later times, the overall degrees of carbonation observed in the wastes were significant (> 80%), a majority of which occurs within the first 2 days of reaction. Under the operational conditions applied in this study, the degree of carbonation in CKD achieved in column-scale systems was comparable to those observed under ideal batch conditions. In addition, the similarity in sequestration performance among several different CKD waste types indicates that, aside from available oxide content, no compositional factors significantly hinder the ability of the waste to sequester CO2.

Analysis of a Non-Traditional Micro Tube Hydroforming Process

As the demand for miniature products and components continues to increase, the need for manufacturing processes to provide these products and components has also increased. To meet this need, successful macroscale processes are being scaled down and applied at the microscale. Unfortunately, many challenges have been experienced when directly scaling down macro processes. Initially, frictional effects were believed to be the largest challenge encountered. However, in recent studies it has been found that the greatest challenge encountered has been with size effects. Size effect is a broad term that largely refers to the thickness of the material being formed and how this thickness directly affects the product dimensions and manufacturability. At the microscale, the thickness becomes critical due to the reduced number of grains. When surface contact between the forming tools and the material blanks occur at the macroscale, there is enough material (hundreds of layers of material grains) across the blank thickness to compensate for material flow and the effect of grain orientation. At the microscale, there may be under 10 grains across the blank thickness. With a decreased amount of grains across the thickness, the influence of the grain size, shape and orientation is significant. Any material defects (either natural occurring or ones that occur as a result of the material preparation) have a significant role in altering the forming potential. To date, various micro metal forming and micro materials testing equipment setups have been constructed at the Michigan Tech lab. Initially, the research focus was to create a micro deep drawing setup to potentially build micro sensor encapsulation housings. The research focus shifted to micro metal materials testing equipment setups. These include the construction and testing of the following setups: a micro mechanical bulge test, a micro sheet tension test (testing micro tensile bars), a micro strain analysis (with the use of optical lithography and chemical etching) and a micro sheet hydroforming bulge test. Recently, the focus has shifted to study a micro tube hydroforming process. The intent is to target fuel cells, medical, and sensor encapsulation applications. While the tube hydroforming process is widely understood at the macroscale, the microscale process also offers some significant challenges in terms of size effects. Current work is being conducted in applying direct current to enhance micro tube hydroforming formability. Initially, adding direct current to various metal forming operations has shown some phenomenal results. The focus of current research is to determine the validity of this process.

An Empirical Analysis of the Monetary Policy Reaction Function in India

This paper empirically analyzes India’s monetary policy reaction function by applying the Taylor (1993) rule and its open-economy version which employs dynamic OLS. The analysis uses monthly data from the period of April 1998 to December 2007. When the simple Taylor rule was estimated for India, the output gap coefficient was statistically significant, and its sign condition was found to be consistent with theoretical rationale; however, the same was not true of the inflation coefficient. When the Taylor rule with exchange rate was estimated, the coefficients of output gap and exchange rate had statistical significance with the expected signs, whereas the results of inflation remained the same as before. Therefore, the inflation rate has not played a role in the conduct of India’s monetary policy, and it is inappropriate for India to adopt an inflation-target type policy framework.

The aggressiveness of pig slurry to cement mortars

The aim was to measure the behaviour of various mortars employed in livestock media in central Spain and to analyse the aggressiveness of pig slurry to cement blended with fly ash mortars. To achieve this, mortar specimens were immersed in ponds storing pig slurry. Mortar specimens, of 40 ? 40 ? 160 mm, were made from four types of cement commonly used and recommended for rural areas. The types were a sulphate-resistant Portland cement and three cements blended in different proportions with fly ash and limestone filler. After 3, 6, 12, 24, 36, 48 and 60 months of exposure, three or four specimens of each cement type were removed from the pond and washed with water. Their compressive strength and microstructure (X-ray diffraction, mercury intrusion pore-symmetry, thermal analysis and scanning electron microscopy) were then measured. Sulphate-resistant Portland cement (SR-PC), found to be more susceptible to degradation due to its greater proportion of macro-pores and increased total porosity, was found not to be suitable for use with livestock. After 60 months of immersion in the pig slurry medium, CEM II-A (40.3%) mortar retained the greatest compressive strength. Mortars with less than 20% replacement of cement by fly ash were found to be the most durable, with the most suitable mechanical behaviour.

Evaluating the reinforcement of inorganic fullerene-like nanoparticles in thermoplastic matrices by depth-sensing indentation

The reinforcing effect of inorganic fullerene-like tungsten disulfide (IF-WS2) nanoparticles in two different polymer matrices, isotactic polypropylene (iPP) and polyphenylene sulfide (PPS), has been investigated by means of dynamic depth-sensing indentation. The hardness and elastic modulus enhancement upon filler addition is analyzed in terms of two main contributions: changes in the polymer matrix nanostructure and intrinsic properties of the filler including matrix-particle load transfer. It is found that the latter mainly determines the overall mechanical improvement, whereas the nanostructural changes induced in the polymer matrix only contribute to a minor extent. Important differences are suggested between the mechanisms of deformation in the two nanocomposites, resulting in a moderate mechanical enhancement in case of iPP (20% for a filler loading of 1%), and a remarkable hardness increase in case of PPS (60% for the same filler content). The nature of the polymer amorphous phase, whether in the glassy or rubbery state, seems to play here an important role. Finally, nanoindentation and dynamic mechanical analysis measurements are compared and discussed in terms of the different directionality of the stresses applied.

Métodos numéricos y estadísticos de caracterización de uniones tubulares soldadas para su aplicación en modelos de elementos finitos de estructuras de vehículos

El análisis de estructuras mediante modelos de elementos finitos representa una de las metodologías más utilizadas y aceptadas en la industria moderna. Para el análisis de estructuras tubulares de grandes dimensiones similares a las sobrestructuras de autobuses y autocares, los elementos de tipo viga son comúnmente utilizados y recomendados debido a que permiten obtener resultados satisfactorios con recursos computacionales reducidos. No obstante, los elementos de tipo viga presentan importante desventaja ya que las uniones modeladas presentan un comportamiento infinitamente rígido, esto determina un comportamiento mas rígido en las estructuras modeladas lo que se traduce en fuentes de error para las simulaciones estructurales (hasta un 60%). Mediante el modelado de uniones tubulares utilizando elementos de tipo área o volumen, se pueden obtener modelos más realistas, ya que las características topológicas de la unión propiamente dicha pueden ser reproducidas con un mayor nivel de detalle. Evitándose de esta manera los inconvenientes de los elementos de tipo viga. A pesar de esto, la modelización de estructuras tubulares de grandes dimensiones con elementos de tipo área o volumen representa una alternativa poco atractiva debido a la complejidad del proceso de modelados y al gran número de elementos resultantes lo que implica la necesidad de grandes recursos computacionales. El principal objetivo del trabajo de investigación presentado, fue el de obtener un nuevo tipo de elemento capaz de proporcionar estimaciones más exactas en el comportamiento de las uniones modeladas, al mismo tiempo manteniendo la simplicidad del procesos de modelado propio de los elementos de tipo viga regular. Con el fin de alcanzar los objetivos planteados, fueron realizadas diferentes metodologías e investigaciones. En base a las investigaciones realizadas, se obtuvo un modelo de unión viga alternativa en el cual se introdujeron un total seis elementos elásticos al nivel de la unión mediante los cuales es posible adaptar el comportamiento local de la misma. Adicionalmente, para la estimación de las rigideces correspondientes a los elementos elásticos se desarrollaron dos metodologías, una primera basada en la caracterización del comportamiento estático de uniones simples y una segunda basada en la caracterización del comportamiento dinámico a través de análisis modales. Las mejoras obtenidas mediante la implementación del modelo de unión alternativa fueron analizadas mediante simulaciones y validación experimental en una estructura tubular compleja representativa de sobrestructuras de autobuses y autocares. En base a los análisis comparativos realizados con la uniones simples modeladas y los experimentos de validación, se determinó que las uniones modeladas con elementos de tipo viga son entre un 5-60% más rígidas que uniones equivalentes modeladas con elementos área o volumen. También se determinó que las uniones área y volumen modeladas son entre un 5 a un 10% mas rígidas en comparación a uniones reales fabricadas. En los análisis realizados en la estructura tubular compleja, se obtuvieron mejoras importantes mediante la implementación del modelo de unión alternativa, las estimaciones del modelo viga se mejoraron desde un 49% hasta aproximadamente un 14%. ABSTRACT The analysis of structures with finite elements models represents one of the most utilized an accepted technique in the modern industry. For the analysis of large tubular structures similar to buses and coaches upper structures, beam type elements are utilized and recommended due to the fact that these elements provide satisfactory results at relatively reduced computational performances. However, the beam type elements have a main disadvantage determined by the fact that the modeled joints have an infinite rigid behavior, this shortcoming determines a stiffer behavior of the modeled structures which translates into error sources for the structural simulations (up to 60%). By modeling tubular junctions with shell and volume elements, more realistic models can be obtained, because the topological characteristics of the junction at the joint level can be reproduced more accurately. This way, the shortcoming that the beam type elements present can be solved. Despite this fact, modeling large tubular structures with shell or volume type elements represents an unattractive alternative due to the complexity of the modeling process and the large number of elements that result which imply the necessity of vast computational performances. The main objective of the research presented in this thesis was to develop a new beam type element that would be able to provide more accurate estimations for the local behavior of the modeled junctions at the same time maintaining the simplicity of the modeling process the regular beam type elements have. In order to reach the established objectives of the research activities, a series of different methodologies and investigations have been necessary. From these investigations an alternative beam T-junction model was obtained, in which a total of six elastic elements at the joint level were introduced, the elastic elements allowed us to adapt the local behavior of the modeled junctions. Additionally, for the estimation of the stiffness values corresponding to the elastic elements two methodologies were developed, one based on the T-junction’s static behavior and a second one based on the T-junction’s dynamic behavior by means of modal analysis. The improvements achieved throughout the implementation of this alternative T-junction model were analyzed though mechanical validation in a complex tubular structures that had a representative configuration for buses and coaches upper structures. From the comparative analyses of the finite element modeled T-junctions and mechanical experimental analysis, was determined that the beam type modeled T-junctions have a stiffer behavior compared to equivalent shell and volume modeled T-junctions with average differences ranging from 5-60% based on the profile configurations. It was also determined that the shell and volume models have a stiffer behavior compared to real T-junctions varying from 5 to 10% depending on the profile configurations. Based on the analysis of the complex tubular structure, significant improvements were obtained by the implementation of the alternative beam T-junction model, the model estimations were improved from a 49% to approximately 14%.

Real time monitoring of click chemistry self-healing in polymer composites

A photo-healable rubber composite based on effective and fast thiol-alkyne click chemistry as a selfhealing agent prestored in glass capillaries is reported. The click reaction and its effect on the mechanical properties of the composite are monitored in real time by dynamic mechanical analysis, showing that the successful bleeding of healing agents to the crack areas and the effective photoinitiated click reaction result in a 30% storage modulus increase after only 5 min of UV light exposure. X-ray tomography confirms capillary-driven bleeding of reactants to the damaged areas. The effect of storing the click chemistry reactants in separate capillaries is also studied, and results show the importance of stoichiometry in achieving a significant level of repair of the composite. No reactant degradation or premature chemical reaction is observed over time in samples stored in the absence of UV radiation; they are able to undergo the self-healing reaction even one month after preparation.

Analysis of single and binary phases in cerium doped sodium bismuth titanate -Na0.5Bi0.5TiO3 materials

The pure and cerium doped sodium bismuth titanate inorganic powders were synthesized by solid state reaction method. The presence of rhombohedral phase was observed in cerium doped NBT compounds. At 1200 ºC, the 5% of cerium doped NBT compound forms single perovskite phase. The samples of x = 0.10 and 0.15 were heat treated to 1350 ºC, the binary phases with cerium and bismuth oxides were observed. The X-ray diffraction, fourier transform infrared spectroscopy, reflectance spectra, differential thermal analysis and thermo gravimetric analysis were used to analyze the various properties of samples. Moreover, the effects of cerium doping and calcining temperature on NBT samples were investigated. In this work we present our recent results on the synthesis and characterization of Ce doped sodium bismuth titanate materials.

Estudio microestructural de pastas de cemento expuestas a medios simulados de agresividad moderada frecuentes en ambientes rurales

Los materiales base cemento (pastas, morteros, hormigones y otros tipos de mezclas) son materiales ampliamente utilizados en la sociedad actual y son uno de los pilares de la ingeniería civil debido a sus buenas propiedades estructurales, facilidad de fabricación y bajo coste. Sus propiedades permiten su uso en ambientes industriales y naturales, siendo materiales muy versátiles siempre y cuando, se tenga en cuenta que sus propiedades durables son limitadas en ambientes donde se producen fenómenos de lixiviación y ataque por diversos iones agresivos. El presente proyecto de investigación se desarrolló motivado por la necesidad de profundizar en el conocimiento del comportamiento de los materiales base cemento en situaciones concretas de exposición a cierto tipo de degradaciones que se producen frecuentemente en explotaciones agropecuarias ubicadas en ambientes naturales. Se diseñó un procedimiento experimental que nos permitiese evaluar el efecto que tienen los ácidos orgánicos sobre la matriz cementicia, así como la acción que presentan los sulfatos y las aguas naturales en los mismos. Teniendo muy presente siempre las características de las disoluciones a las cuales se ha expuesto el material. En último término, se trata de conocer los mecanismos de los procesos de ataque para poder definir el comportamiento del material en estos medios. Los procedimientos de ensayo, así como las técnicas de caracterización son las herramientas fundamentales con las que profundizar en el conocimiento del material, por lo que resulta de vital importancia conocer a fondo las posibilidades que su empleo nos ofrece. En el presente trabajo se ha desarrollado un profundo estudio del uso del termoanálisis en la caracterización de pastas de cemento. Además se han optimizado los procedimientos de caracterización de las muestras con otro tipo de técnicas. La caracterización de las probetas nos ha permitido comprobar el comportamiento del material en situaciones de exposición en ensayos acelerados de laboratorio. Los resultados obtenidos han permitido determinar que el pH del medio agresivo es una variable fundamental cuando se trata de evaluar la agresividad del mismo. La presencia de ciertos iones desarrollaría efectos de sinergia con respecto al pH y condicionaría los valores de las constantes termodinámicas que rigen los equilibrios. La posibilidad de formación de sales de ácidos orgánicos y la diferente solubilidad de las mismas derivaría en cambios en los comportamientos mecánicos. La proporción de compuestos de aluminio o la presencia de puzolanas capaces de fijar el calcio son también factores evidenciados como determinantes en el comportamiento del material. Además se podría afirmar que la disolución de la portlandita es un efecto determinante en el proceso de degradación. Nowadays, cement based materials (pastes, mortars, concrete and other mixtures) are widely used. These kinds of material are one of the pillars of Civil Engineering due to their structural properties, easy manufacturing and low cost. Their properties allow the use in industrial and natural environments. They are very versatile materials for use in this type of environment. But it is necessary to to keep in mind that they have a durability limited when they are exposed to aggressives environments where leaching process occur and various aggressive ions can damage the materials. This research work was developed motivated by the need to go in dept in the knoledge of the behavior of cement based materials. These kinds of materials frecuently are exposed to some types of damage that occur on farms located in natural environments. An experimental procedure that would allow us to evaluate the effect of organic acids on the cement matrix and the action presented by sulfates and natural waters in the same was designed. Always bearing in mind the characteristics of the solutions to which the material is exposed. Ultimately it comes to understanding the mechanisms of the processes leading to define the material behavior in this type of environment. Test procedures and characterization techniques are fundamental tools which to deepen the knowledge of the material, so it is important to know in its potential uses. In this work we have developed a deep study of the use of thermal analysis in the characterization of cement pastes. Furthermore, we have optimized characterization procedures of samples with other techniques. The characterization of the samples has allowed us to check the behavior of the material on exposure to accelerated laboratory tests. The results have established that the pH of the corrosive media is a fundamental variable when it comes to assessing the aggressiveness of it. The presences of certain ions develop synergies with respect to pH and would determine the values of the constants governing thermodynamic equilibria. The possible formation of salts of organic acids and the different solubility of the same would lead to changes in mechanical behavior. The proportion of aluminum compounds or the presence of pozzolans capable of binding calcium is also evidenced as determining factors in the material behavior. Besides we could assert that the dissolution of the portlandite is a determining effect on the degradation process.

Analytical study of the thermal behaviour and stability of a small satellite

In this work the thermal analysis of a small satellite orbiting around the Earth has been approached by direct integration of the heat balance equations of a two-node reduced model, obtaining a linearized second order ODE problem, similar in form to the classical case of the forced vibration of a damped system. As the thermal loads (solar radiation, albedo, etc.) are harmonic, the problem is solved by means of Fourier analysis methods. Research on that field can be directly applied to the analysis of thermal problems and the results obtained are satisfactory. Working on the frequency domain streamlines the analysis, simplifies the study and facilitates the experimental testing. The transfer functions are obtained for the two-node case but the study can be extended to an n-node model.

Fresnel-based modular solar fields for performance/cost optimization in solar thermal power plants: A comparison with parabolic trough collectors.

Linear Fresnel collectors are identified as a technology that should play a main role in order to reduce cost of Concentrating Solar Power. An optical and thermal analysis of the different blocks of the solar power plant is carried out, where Fresnel arrays are compared with the most extended linear technology: parabolic trough collectors. It is demonstrated that the optical performance of Fresnel array is very close to that of PTC, with similar values of maximum flux intensities. In addition, if the heat carrier fluid flows in series by the tubes of the receiver, relatively high thermal efficiencies are achieved. Thus, an annual solar to electricity efficiency of 19% is expected, which is similar to the state of the art in PTCs; this is done with a reduction of costs, thanks to lighter structures, that drives to an estimation of LCOE of around 6.5 c€/kWh.

Bio-based polymer nanocomposites based on nylon 11 and WS2 inorganic nanotubes

Tungsten disulphide nanotubes (INT-WS2) have been successfully dispersed in a bio-based polyamide matrix (nylon 11) by conventional melt processing. The effect of INT-WS2 content on the morphology, thermal stability, crystallization behaviour and dynamic mechanical properties is investigated. The results indicate that these inorganic nanotubes can be efficiently incorporated into the bio-based polymer matrix without the need for modifiers or surfactants. Additionally, it is found that the non-isothermal crystallization behaviour of nylon 11/INT-WS2 depends on both the cooling rate and INT-WS2 concentration. In particular, crystallization kinetics results demonstrate that the nucleating activity of INTs plays a dominant role in accelerating the crystallization of nylon 11. This fact leads to the appearance of the more-disordered phase at higher temperature. More significantly, it was shown that these INT-WS2 nanocomposites can facilitate a good processability and cost efficiency, and will be of interest for many eco-friendly and medical applications.

Solvent dependence of dynamic transitions in protein solutions

A transition as a function of increasing temperature from harmonic to anharmonic dynamics has been observed in globular proteins by using spectroscopic, scattering, and computer simulation techniques. We present here results of a dynamic neutron scattering analysis of the solvent dependence of the picosecond-time scale dynamic transition behavior of solutions of a simple single-subunit enzyme, xylanase. The protein is examined in powder form, in D2O, and in four two-component perdeuterated single-phase cryosolvents in which it is active and stable. The scattering profiles of the mixed solvent systems in the absence of protein are also determined. The general features of the dynamic transition behavior of the protein solutions follow those of the solvents. The dynamic transition in all of the mixed cryosolvent–protein systems is much more gradual than in pure D2O, consistent with a distribution of energy barriers. The differences between the dynamic behaviors of the various cryosolvent protein solutions themselves are remarkably small. The results are consistent with a picture in which the picosecond-time scale atomic dynamics respond strongly to melting of pure water solvent but are relatively invariant in cryosolvents of differing compositions and melting points.

Caracterização físico-química e analítica de fibras capilares e ingredientes cosméticos para proteção

Com o aumento dos tratamentos químicos e/ou físicos nos cabelos aos quais são realizados mediante o uso de dispositivos térmicos, há uma maior preocupação a respeito dos danos causados aos cabelos por estes tipos de tratamentos. O conhecimento dos efeitos, benefícios e/ou malefícios, de ingredientes cosméticos em cabelos torna-se necessário, pois facilita a busca por produtos baseada no tipo de cabelo. O principal objetivo do trabalho foi a caracterização físico-química, analítica e térmica de mechas de cabelo de diferentes etnias (caucasiano, oriental e afro-étnico virgem e brasileiro virgem e descolorido) antes e após o uso de ingredientes cosméticos seguido de um tratamento térmico (utilizando piastra) e intercalando com lavagens. O estudo das amostras de cabelo e de uma amostra de queratina animal envolveu a utilização das técnicas de TG/DTG, DSC, análise elementar, FTIR, MEV e técnicas de avaliação de eficácia, como tensão/deformação, penteabilidade e quebra por escovação. A partir da TG/DTG, foi possível avaliar as etapas de decomposição térmica das amostras de cabelo virgem e de queratina animal e estas apresentaram um comportamento térmico semelhante entre si. O estudo cinético não isotérmico por TG mostrou que, dos diferentes tipos de amostras de cabelo virgem, o afro-étnico apresentou menor estabilidade térmica e o oriental foi o mais estável termicamente. Os resultados de DSC corroboraram os obtidos por TG, demonstrando que a amostra de cabelo afro-étnico apresentou temperatura de desnaturação térmica das cadeias de α-queratina menor (TD = 223°C) do que as amostras dos outros tipos de cabelo (TD = 236°C). As mechas de cabelo virgem e clareadas foram tratadas com formulações cosméticas contendo silicones e avaliadas quanto a eficiência destes na proteção térmica dos cabelos. Algumas delas mostraram eficiência na proteção térmica das cadeias de α-queratina, diminuindo o seu grau de desnaturação. Foi possível observar que a associação do calor da piastra com as lavagens sucessivas causou danos tanto à cutícula (conforme resultados de FTIR e MEV), como também, ao córtex dos cabelos (conforme resultados de DSC). Em alguns casos, os danos causados foram tão graves que as camadas mais superficiais da cutícula sofreram descamações. O estudo mostrou, também, que a eficiência da proteção térmica nos cabelos depende do tipo da formulação cosmética em que estes protetores estão incorporados e do estado em que os cabelos se encontram. A DSC permitiu a avaliação da modificação termicamente induzida das cadeias de α-queratina e sua posterior desnaturação. O estudo envolvendo a associação das diferentes técnicas apresentou-se viável na avaliação tanto dos danos causados aos cabelos quanto na eficiência dos ingredientes cosméticos na proteção térmica dos mesmos.