Genesis and classification of Oxisols in a highland toposequence of the upper Jequitinhonha Valley (MG)

The Brazilian System of Soil Classification (SiBCS) is a taxonomic system, open and in permanent construction, as new knowledge on Brazilian soils is obtained. The objective of this study was to characterize the chemical, physical, morphological, micro-morphological and mineralogical properties of four pedons of Oxisols in a highland toposequence in the upper Jequitinhonha Valley, emphasizing aspects of their genesis, classification and landscape development. The pedons occupy the following slope positions: summit - Red Oxisol (LV), mid slope (upper third) - Yellow-Red Oxisol (LVA), lower slope (middle third)- Yellow Oxisol (LA) and bottom of the valley (lowest third) - "Gray Oxisol" ("LAC"). These pedons were described and sampled for characterization in chemical and physical routine analyses. The total Fe, Al and Mn contents were determined by sulfuric attack and the Fe, Al and Mn oxides in dithionite-citrate-bicarbonate and oxalate extraction. The mineralogy of silicate clays was identified by X ray diffraction and the Fe oxides were detected by differential X ray diffraction. Total Ti, Ga and Zr contents were determined by X ray fluorescence spectrometry. The "LAC" is gray-colored and contains significant fragments of structure units in the form of a dense paste, characteristic of a gleysoil, in the horizons A and BA. All pedons are very clayey, dystrophic and have low contents of available P and a pH of around 5. The soil color was related to the Fe oxide content, which decreased along the slope. The decrease of crystalline and low- crystalline Fe along the slope confirmed the loss of Fe from the "LAC". Total Si increased along the slope and total Al remained constant. The clay fraction in all pedons was dominated by kaolinite and gibbsite. Hematite and goethite were identified in LV, low-intensity hematite and goethite in LVA, goethite in LA. In the "LAC", no hematite peaks and goethite were detected by differential X ray diffraction. The micro-morphology indicated prevalence of granular microstructure and porosity with complex stacking patterns.. The soil properties in the toposequence converged to a single soil class, the Oxisols, derived from the same source material. The landscape evolution and genesis of Oxisols of the highlands in the upper Jequitinhonha Valley are related to the evolution of the drainage system and the activity of excavating fauna.

Dielectric constant obtained from TDR and volumetric moisture of soils in southern Brazil

Soil moisture is the property which most greatly influences the soil dielectric constant, which is also influenced by soil mineralogy. The aim of this study was to determine mathematical models for soil moisture and the dielectric constant (Ka) for a Hapludalf, two clayey Hapludox and a very clayey Hapludox and test the reliability of universal models, such as those proposed by Topp and Ledieu and their co-workers in the 80's, and specific models to estimate soil moisture with a TDR. Soil samples were collected from the 0 to 0.30 m layer, sieved through a mesh of 0.002 m diameter and packed in PVC cylinders with a 0.1 m diameter and 0.3 m height. Seven samples of each soil class were saturated by capillarity and a probe composed of two rods was inserted in each one of them. Moisture readings began with the saturated soil and concluded when the soil was near permanent wilting point. In each step, the samples were weighed on a precision scale to calculate volumetric moisture. Linear and polynomial models were adjusted for each soil class and for all soils together between soil moisture and the dielectric constant. Accuracy of the models was evaluated by the coefficient of determination, the standard error of estimate and the 1:1 line. The models proposed by Topp and Ledieu and their co-workers were not adequate for estimating the moisture in the soil classes studied. The adjusted linear and polynomial models for the entire set of data of the four soil classes did not have sufficient accuracy for estimating soil moisture. The greater the soil clay and Fe oxide content, the greater the dielectric constant of the medium for a given volumetric moisture. The specific models, θ = 0.40283 - 0.04231 Ka + 0.00194 Ka² - 0.000022 Ka³ (Hapludox) θ = 0.01971 + 0.02902 Ka - 0.00086 Ka² + 0.000012 Ka³ (Hapludox -PF), θ = 0.01692 - 0.00507 Ka (Hapludalf) and θ = 0.08471 + 0.01145 Ka (Hapludox-CA), show greater accuracy and reliability for estimating soil moisture in the soil classes studied.

Water-dispersible clay in soils treated with sewage sludge

A by-product of Wastewater Treatment Stations is sewage sludge. By treatment and processing, the sludge is made suitable for rational and environmentally safe use in agriculture. The aim of this study was to assess the influence of different doses of limed sewage sludge (50 %) on clay dispersion in soil samples with different textures (clayey and medium). The study was conducted with soil samples collected from native forest, on a Red Latosol (Brazilian classification: Latossolo Vermelho distroférrico) loamy soil in Londrina (PR) and a Red-Yellow Latosol (BC: Latossolo Vermelho-Amarelo distrófico) medium texture soil in Jaguapitã (PR). Pots were filled with 3 kg of air-dried fine earth and kept in greenhouse. The experiment was arranged in a randomized block design with six treatments: T1 control, and treatments with limed sewage sludge (50 %) as follows: T2 (3 t ha-1), T3 (6 t ha-1), T4 (12 t ha-1), T5 (24 t ha-1) and T6 (48 t ha-1) and five replications. The incubation time was 180 days. At the end of this period, the pots were opened and two sub-samples per treatment collected to determine pH-H2O, pH KCl (1 mol L-1), organic matter content, water-dispersible clay, ΔpH (pH KCl - pH-H2O) and estimated PZC (point of zero charge): PZC = 2 pH KCl - pH-H2O, as well as the mineralogy of the clay fraction, determined by X ray diffraction. The results showed no significant difference in the average values for water-dispersible clay between the control and the other treatments for the two soil samples studied and ΔpH was the variable that correlated best with water-dispersible clay in both soils.

Alpine and pre-Alpine magmatism in the root-zone of the western Central Alps

The highest grade of metamorphism and associated structural elements in orogenic belts may be inherited from earlier orogenic events. We illustrate this point using magmatic and metamorphic rocks from the southern steep belt of the Lepontine Gneiss Dome (Central Alps). The U-Pb zircon ages from an anatectic granite at Verampio and migmatites at Corcapolo and Lavertezzo yield 280-290 Ma, i.e., Hercynian ages. These ages indicate that the highest grade of metamorphism in several crystalline nappes of the Lepontine Gneiss Dome is pre-Alpine. Alpine metamorphism reached sufficiently high grade to reset the Rb-Sr and K-Ar systematics of mica and amphibole, but generally did not result in crustal melting, except in the steep belt to the north of the Insubric Line, where numerous 29 to 26 Ma old pegmatites and aplites had intruded syn- and post-kinematically into gneisses of the ductile Simplon Shear Zone. The emplacement age of these pegmatites gives a minimum estimate for the age of the Alpine metamorphic peak in the Monte Rosa nappe. The U-Pb titanite ages of 33 to 31 Ma from felsic porphyritic veins represent a minimum-age estimate for Alpine metamorphism in the Sesia Zone. A porphyric vein emplaced at 448 +/- 5 Ma (U-Pb monazite) demonstrates that there existed a consolidated Caledonian basement in the Sesia Zone.

Quantification of aluminium in soil of the Solimões Formation, Acre State, Brazil

The variety of soils in the State of Acre is wide and their chemical profiles are still not fully understood. The nature of the material of origin of these soils is indicated by the high aluminium (Al) content, commonly associated with high calcium (Ca) and magnesium (Mg) contents. The study objective was to use different methods to quantify Al in soils from toposequences formed from material of a sedimentary nature originating from the Solimões Formation, in Acre, Brazil. Trenches were opened at three distinct points in the landscape: shoulder, backslope and footslope positions. Soil samples were collected for physical, chemical, mineralogical analyses. The Al content was quantified using different methods. High Al contents were found in most of these horizons, associated with high Ca and Mg levels, representing the predominant cations in the sum of exchangeable bases. The mineralogy indicates that the soils are still in a low weathering phase, with the presence of significant quantities of 2:1 minerals. Similar Al contents were determined by the methods of NaOH titration, xylenol orange spectrometry and inductively coupled plasma optical emission spectrometry. However, no consistent data were obtained by the pyrocatechol violet method. Extraction with KCl overestimated the exchangeable Al content due to its ability to extract the non-exchangeable Al present in the smectite interlayers. It was observed that high Al contents are related to the instability of the hydroxyl-Al smectite interlayers.

Properties of debris flow deposits and source materials compared: implications for debris flow characterization

In the Alps, debris flow deposits generally contain < 5% clay-size particles, and the role of the surface-charged < 2 mu m particles is often neglected, although these particles may have a significant impact on the rheological properties of the interstitial fluid. The objective of this study was to compare debris flow deposits and parent materials from two neighbouring catchments of the Swiss Alps, with special emphasis on the colloidal constituents. The catchments are small in area (4 km(2)), 2.5 km long, similar in morphology, but different in geology. The average slopes are 35-40%. The catchments were monitored for debris flow events and mapped for surface aspect and erosion activity. Debris flow deposits and parent materials were sampled, the clay and silt fractions extracted and the bulk density, < 2 mm fraction bulk density, particle size distribution, chemical composition, cation exchange capacity (CEC) and mineralogy analysed. The results show that the deposits are similar to the parent screes in terms of chemical composition, but differ in terms of: (i) particle size distribution; and (ii) mineralogy, reactivity and density of the < 2 mm fraction. In this fraction, compared with the parent materials the deposits show dense materials enriched in coarse monocrystalline particles, of which the smallest and more reactive particles were leached. The results suggest that deposit samples should not be considered as representative of source or flow materials, particularly with respect to their physical properties.

INTERNAL STRUCTURE OF A VERMICULAR IRONSTONE AS DETERMINED BY X-RAY COMPUTED TOMOGRAPHY SCANNING

Ironstones or petroplinthites are common materials in soils under humid tropical climate, generally defined as the result of Fe oxide accumulation in areas where the water table oscillates, and may exhibit considerable morphological variability. The aim of this study was to examine the internal structure and porosity of an ironstone fragment from a Petroferric Acrudox in Minas Gerais, Brazil, by computed tomography (CT) and conventional techniques. The sample analyzed had total porosity of 59.5 %, with large macropores in the form of tubular channels and irregular vughs, the latter with variable degrees of infilling by material released from the ironstone walls or the soil matrix. The CT scan also showed that the ironstone has wide variation in the density of the solid phase, most likely due to higher concentrations or thick intergrowths of hematite and magnetite/maghemite, especially in its outer rims. The implications of these results for water retention and soil formation in ironstone environments are briefly discussed.

Alkali-calcic and alkaline post-orogenic (PO) granite magmatism: petrologic constraints and geodynamic settings

The end of an orogenic Wilson cycle corresponds to amalgamation of terranes into a Pangaea and is marked by widespread magmatism dominated by granitoids. The post-collision event starts with magmatic processes still influenced by subducted crustal materials. The dominantly calc-alkaline suites show a shift from normal to high-K to very high-K associations. Source regions are composed of depleted and later enriched orogenic subcontinental lithospheric mantle, affected by dehydration melting and generating more and more K- and LILE-rich magmas. In the vicinity of intra-crustal magma chambers, anatexis by incongruent melting of hydrous minerals may generate peraluminous granitoids bearing mafic enclaves. The post-collision event ends with emplacement of bimodal post-orogenic (PO) suites along transcurrent fault zones. Two suites are defined, (i) the alkali-calcic monzonite-monzogranite-syenogranite-alkali feldspar granite association characterised by [biotite + plagioclase] fractionation and moderate [LILE + HFSE] enrichments and (ii) the alkaline monzonite-syenite-alkali feldspar granite association characterised by [amphibole + alkali feldspar] fractionation and displaying two evolutionary trends, one peralkaline with sodic mafic mineralogy and higher enrichments in HFSE than in LILE, and the other aluminous biotite-bearing marked by HFSE depletion relative to LILE due to accessory mineral precipitation. Alkali-calcic and alkaline suites differ essentially in the amounts of water present within intra-crustal magma chambers, promoting crystallisation of various mineral assemblages. The ultimate enriched and not depleted mantle source is identical for the two PO suites. The more primitive LILE and HFSE-rich source rapidly replaces the older orogenic mantle source during lithosphere delamination and becomes progressively the thermal boundary layer of the new lithosphere. Present rock compositions are a mixture of major mantle contribution and various crustal components carried by F-rich aqueous fluids circulating within convective cells created around magma chambers. In favourable areas, PO suites pre-date a new orogenic Wilson cycle. (C) 1998 Elsevier Science B.V. All rights reserved.

Sustainability of Wood Productivity of Pinus TaedaBased on Nutrient Export and Stocks in the Biomass and in the Soil

ABSTRACT The impact of intensive management practices on the sustainability of forest production depends on maintenance of soil fertility. The contribution of forest residues and nutrient cycling in this process is critical. A 16-year-old stand of Pinus taeda in a Cambissolo Húmico Alumínico léptico (Humic Endo-lithic Dystrudept) in the south of Brazil was studied. A total of 10 trees were sampled distributed in five diameter classes according to diameter at breast height. The biomass of the needles, twigs, bark, wood, and roots was measured for each tree. In addition to plant biomass, accumulated plant litter was sampled, and soil samples were taken at three increments based on sampling depth: 0.00-0.20, 0.20-0.40, 0.40-0.60, 0.60-1.00, 1.00-1.40, 1.40-1.80, and 1.80-1.90 m. The quantity and concentration of nutrients, as well as mineralogical characteristics, were determined for each soil sample. Three scenarios of harvesting intensities were simulated: wood removal (A), wood and bark removal (B), and wood + bark + canopy removal (C). The sum of all biomass components was 313 Mg ha-1.The stocks of nutrients in the trees decreased in the order N>Ca>K>S>Mg>P. The mineralogy of the Cambissolo Húmico Alumínico léptico showed the predominance of quartz sand and small traces of vermiculite in the silt fraction. Clay is the main fraction that contributes to soil weathering, due to the transformation of illite-vermiculite, releasing K. The depletion of nutrients from the soil biomass was in the order: P>S>N>K>Mg>Ca. Phosphorus and S were the most limiting in scenario A due to their low stock in the soil. In scenario B, the number of forest rotations was limited by N, K, and S. Scenario C showed the greatest reduction in productivity, allowing only two rotations before P limitation. It is therefore apparent that there may be a difference of up to 30 years in the capacity of the soil to support a scenario such as A, with a low nutrient removal, compared to scenario C, with a high nutrient removal. Hence, the effect of different harvesting intensities on nutrient availability may jeopardize the sustainability of P. taeda in the short-term.

Planosols Developed in Different Geoenvironmental Conditions in Northeastern Brazil

ABSTRACT The semiarid region of northeastern Brazil has a large area occupied by Planosols, where in the State of Pernambuco these soils are mainly used for livestock farming and subsistence crops. The knowledge on these soils is limited, which compromises the understanding on their behavior, potentialities and limitations.This study aimed to analyze morphological, chemical, physical and mineralogical attributes of Planosols developed under different geoenvironmental conditions. Morphological descriptions and chemical, physical and mineralogical analyses were performed in four profiles of Planosols along a rainfall gradient. An increase in rainfall allowed for an increase in the clay content in the Bt horizon and a reduction in ESP, EC, Na+, CEC, S, pH (water and KCl) and soil density. Horizons A and E were thicker in Planosols in more humid environments. The increase in ESP associated with the presence of expansive minerals (smectite and vermiculite) allowed the development of a prismatic structure in Haplic Planosols and a columnar structure in Natric Planosols. The mineralogical assembly is indicative of poorly weathered soils. The mineralogical assemblies of the silt and clay fractions were similar in the different geoenvironments, while higher contents of easily alterable minerals were observed in the composition of the sand fraction in environments with a drier climate.

The roles of flux- and decompression melting and their respective fractionation lines for continental crust formation: Evidence from the Kohistan arc

Delamination and foundering of the lower continental crust (LCC) into the mantle is part of the crust-forming mechanism. However, knowledge of the composition and mineralogy of the preserved or delaminated LCC over geological timescales remains scarce. We provide a synopsis of recent research within the Kohistan arc (Pakistan) and demonstrate that hydrous and less hydrous liquid lines of descent related to flux assisted and decompression mantle melting, respectively, produce compositionally different lower crustal rocks. The argument refers to two lower crustal sections exposed in Kohistan, the older Southern Plutonic Complex (SPC) and the younger Chilas Complex. The SPC typifies a hydrous, high-pressure fractionation sequence of olivine-pyroxenes-garnet-Fe/Ti-oxide-amphibole-plagioclase. The Chilas Complex illustrates a less hydrous fractionation sequence of olivine-clinopyroxene-orthopyroxene-plagioclase-amphibole. Despite the similarity of the Chilas Complex rocks to proposed lower crust compositions, the less hydrous fractionation results in unrealistically small volumes of silica-rich rocks, precluding the Chilas Complex gabbros to represent the magmatic complement to the upper crust. The composition of the SPC lower crust differs markedly from bulk lower crust estimates, but is complementary to silica-rich rocks exposed along this section and in the Kohistan batholith. These observations inspire a composite model for the formation of continental crust (CC) where the negatively buoyant delaminated and the buoyant preserved lower continental crusts (LCC) differ in genesis, mineralogy, and composition. We propose that the upper, non-sedimentary subsequent removal of the complementary, negatively buoyant garnet-pyroxene-amphibole-plagioclase-rich cumulates. In contrast, the LCC, which is buoyant and preserved over geological timescales, is formed by less hydrous parental mantle melts. We suggest that the bulk continental crust composition is related to mixing of these petrologically not directly related end members. Published by Elsevier B.V.

Final Report Factors Influencing Stability of Granular Base Course Mixes

To evaluate the various factors influencing the stability of granular base course mixes, three primary goals were included in the project: (1) determination of a suitable and realistic laboratory method of compaction; (2) effect of gradation, density and mineralogy of the fines on sheara ing strength; and (3) possible improvement of the shear strength with organic and inorganic chemical stabilization additives.

Geochemical and H-O-Sr-Nd isotope evidence for magmatic processes and meteoric-water interactions in the basal complex of La Gomera, Canary Islands

The plutonic rocks of the Basal Complex of La Gomera, Canary Islands, Spain, were studied by means of major and trace element contents and by H-O-Sr-Nd isotope compositions in order to distinguish primary magmatic characteristics and late-stage alteration products. Deciphering the effects of alteration allowed us to determine primary, plume-related compositions that indicated D- and (18)O-depletion relative to normal upper mantle, supporting the conclusions of earlier studies on the plutonic rocks of Fuerteventura and La Palma. Late-stage alteration took place during the formation of the intrusive series induced by interaction with meteoric water. Inferred isotopic compositions of the meteoric water indicate that the water infiltrated into the rock edifice at a height of about 1500 m above sea level, suggesting the existence of a subaerial volcano which was active during the intrusive activity and that it has been either distroyed or remain buried by later volcanic and landslide events.

Origin of siderite mineralisation in Petrova and Trgovska Gora Mts., NW Dinarides

The Petrova and Trgovska Gora Mts. (Gora=Mountain) are Variscan basement units incorporated into the northwestern Dinarides during the Alpine orogeny. They host numerous siderite-quartz-polysulphide, siderite-chalcopyrite, siderite-galena and barite veins, as well as stratabound hydrothermal-replacement ankerite bodies within carbonates in non-metamorphosed, flysch-like Permo-Carboniferous sequences. The deposits have been mined for Cu, Pb, Ag and Fe ores since Medieval times. Fluid inclusion studies of quartz from siderite-polysulphide-quartz and barite veins of both regions have shown the presence of primary aqueous NaCl-CaCl(2)+/- MgCl(2)-H(2)O +/- CO(2) inclusions. The quartz-sulphide stage of both regions show variable salinities; 2.7-26.2 wt% NaCl eq. for the Trgovska Gora region and 3.4-23.4 wt% NaCl eq. for the Petrova gora region, and similar homogenisation temperatures (100-230A degrees C). Finally, barite is precipitated from low salinity-low temperature solutions (3.7-15.8 wt % NaCl equ. and 115-145A degrees C). P-t conditions estimated via isochore construction yield formation temperatures between 180-250A degrees C for the quartz-sulphide stage and 160-180A degrees C for the barite stage, using a maximum lithostatic pressure of 1 kbar (cc. 3 km of overburden). The sulphur isotope composition of barite from both deposits indicates the involvement of Permian seawater in ore fluids. This is supported by the elevated bromium content of the fluid inclusion leachates (120-660 ppm in quartz, 420-960 ppm in barite) with respect to the seawater, indicating evaporated seawater as the major portion of the ore-forming fluids. Variable sulphur isotope compositions of galena, pyrite and chalcopyrite, between -3.2 and +2.7aEuro degrees, are interpreted as a product of incomplete thermal reduction of the Permian marine sulphate mixed with organically- and pyrite-bound sulphur from the host sedimentary rocks. Ore-forming fluids are interpreted as deep-circulating fluids derived primarily from evaporated Permian seawater and later modified by interaction with the Variscan basement rocks. (40)Ar/(39)Ar data of the detrital mica from the host rocks yielded the Variscan age overprinted by an Early Permian tectonothermal event dated at 266-274 Ma. These ages are interpreted as those reflecting hydrothermal activity correlated with an incipient intracontinental rifting in the Tethyan domain. Nevertheless, 75 Ma recorded at a fine-grained sericite sample from the alteration zone is interpreted as a result of later resetting of white mica during Campanian opening/closure of the Sava back arc in the neighbouring Sava suture zone (Ustaszewski et al. 2008).

The 500 Ma-old Thyon metagranite: A new A-type granite occurrence in the western Penninic Alps (Wallis, Switzerland)

The Thyon metagranite is located in the frontal part of the Siviez-Mischabel Nappe, in the western Penninic Alps. It is intrusive in a polymetamorphic banded volcanic complex as leucocratic concordant sills with pseudoaplitic rims. A distinct metamorphic schistosity is defined by dark-green Fe-rich biotite. Abundant mesoperthites, chess-board albite and low microcline are presumably related to magmatic stages and/or greenschist-facies metamorphic retrogression. Major, trace element and REE geochemistry, zircon typology, Y and Nb-bearing accessory minerals such as fergusonite and euxenite, all point to a metaluminous to peraluminous alkaline A-type granite. High-precision U-Pb zircon dating yielded a sub-concordant age of 500 +3/-4 Ma. The Thyon metagranite is the third record of a Cambro-Ordovician alkaline magmatic activity in the Alps. As A-type granitic magmatism is common in post-orogenic to anorogenic extensional tectonic regime, the Thyon intrusion could mark the transition between the Cadomian and the Caledonian orogenies.