CuIn1-xAlxSe2 Thin Films Grown by Co-Sputtering and Modified Selenization: Application in Flexible Solar Cells

Thin films of CuIn1-xAlxSe2 (CIAS) were grown on the flexible 10 micrometer thin stainless steel substrates, by dc co-sputtering from the elemental cathodes, followed by annealing with modified selenization. CuInAl alloyed precursor films were selenized both by noble gas assisted Se vapor transport in a tubular furnace and vacuum evaporation of Se in an evaporation chamber. CIAS thin films were optimized for better adhesion. X-ray diffraction, scanning electron microscopy, and UV-visible absorption spectroscopy were used to characterize the selenized films. The composition of CIAS films was varied by substituting In with Al in CuInSe2 (CIS) from 0 <= x <= 0.65 (x = Al/Al+In). Lattice parameters, average crystallite sizes, and compact density of the films, decreased when compared to CIS and (112) peak shifted to higher Bragg's angle, upon Al incorporation. The dislocation density and strain were found to increase with Al doping. Solar cells with SS/Mo/CIAS/CdS/iZnO: AZnO/Al configuration were fabricated and were tested for current-voltage characteristics for various `x' values, under Air Mass 1.5 Global one sun illumination. The best CIAS solar cell showed the efficiency of 6.8%, with x = 0.13, Eg = 1.17 eV, fill factor 45.04, and short circuit current density J(sc) 30 mA/cm(2).

Formation and structure of composite coating of HDA and micro-plasma oxidation on A3 steel

Composite coatings were obtained on A3 steel by hot dipping aluminum(HDA) at 720 ℃ for 6 min and micro-plasma oxidation(MPO) in alkali electrolyte. The surface morphology, element distribution and interface structure of composite coatings were studied by means of XRD, SEM and EDS. The results show that the composite coatings obtained through HDA/MPO on A3 steel consist of four layers. From the surface to the substrate, the layer is loose Al2O3 ceramic, compact Al2O3 ceramic, Al and FeAl intermetallic compound layer in turn. The adhesions among all the layers are strengthened because the ceramic layer formed at the Al surface originally, FeAl intermetallic compound layer and substrate are combined in metallurgical form through mutual diffusion during HDA process.Initial experiment results disclose that the anti-corrosion performance and wear resistance of composite coating are obviously improved through HDA/MPO treatment.

Direct numerical simulation of transition and turbulence in compressible mixing layer

The three-dimensional compressible Navier-Stokes equations are approximated by a fifth order upwind compact and a sixth order symmetrical compact difference relations combined with three-stage Ronge-Kutta method. The computed results are presented for convective Mach number Mc = 0.8 and Re = 200 with initial data which have equal and opposite oblique waves. From the computed results we can see the variation of coherent structures with time integration and full process of instability, formation of Lambda-vortices, double horseshoe vortices and mushroom structures. The large structures break into small and smaller vortex structures. Finally, the movement of small structure becomes dominant, and flow field turns into turbulence. It is noted that production of small vortex structures is combined with turning of symmetrical structures to unsymmetrical ones. It is shown in the present computation that the flow field turns into turbulence directly from initial instability and there is not vortex pairing in process of transition. It means that for large convective Mach number the transition mechanism for compressible mixing layer differs from that in incompressible mixing layer.

Generation of large-scale vortex dislocations in a three-dimensional wake-type flow

Numerical study of three-dimensional evolution of wake-type flow and vortex dislocations is performed by using a compact finite diffenence-Fourier spectral method to solve 3-D incompressible Navier-Stokes equations. A local spanwise nonuniformity in momentum defect is imposed on the incoming wake-type flow. The present numerical results have shown that the flow instability leads to three-dimensional vortex streets, whose frequency, phase as well as the strength vary with the span caused by the local nonuniformity. The vortex dislocations are generated in the nonuniform region and the large-scale chain-like vortex linkage structures in the dislocations are shown. The generation and the characteristics of the vortex dislocations are described in detail.

Wideband-tuneable, nanotube mode-locked, fibre laser.

Ultrashort-pulse lasers with spectral tuning capability have widespread applications in fields such as spectroscopy, biomedical research and telecommunications. Mode-locked fibre lasers are convenient and powerful sources of ultrashort pulses, and the inclusion of a broadband saturable absorber as a passive optical switch inside the laser cavity may offer tuneability over a range of wavelengths. Semiconductor saturable absorber mirrors are widely used in fibre lasers, but their operating range is typically limited to a few tens of nanometres, and their fabrication can be challenging in the 1.3-1.5 microm wavelength region used for optical communications. Single-walled carbon nanotubes are excellent saturable absorbers because of their subpicosecond recovery time, low saturation intensity, polarization insensitivity, and mechanical and environmental robustness. Here, we engineer a nanotube-polycarbonate film with a wide bandwidth (>300 nm) around 1.55 microm, and then use it to demonstrate a 2.4 ps Er(3+)-doped fibre laser that is tuneable from 1,518 to 1,558 nm. In principle, different diameters and chiralities of nanotubes could be combined to enable compact, mode-locked fibre lasers that are tuneable over a much broader range of wavelengths than other systems.

六阶精度的群速度直接控制紧致格式及其应用

差分数值解产生非特殊振荡的直接原因是在于非均一的波群的群速度，因此本文利用直接群速度控制的方法重新构造具有六阶精度的紧致型差分格式，以达到改善激波数值解的目的。对所构造的格式的精度及数值解随控制参数变化的行为进行了分析。最后文中给出了一些典型算例，证明了文中所构造的格式具有方法简便，物理含义清楚，精度高，网格基架点小，和捕捉激波能力较强的优点。

The Heterogeneous Growth of P(3MeTh)--An Ellipsometric Study

Successive thicker P(3MeTh) layers are analysed by ex situ conventional and imaging ellipsometry. Thin films display a smooth surface, are compact and homogeneous while for a growth charge above 20 mC cm(-2) the polymer structure modifies to a still uniform but less dense layer. A two-layer model is used and a mathematical procedure is developed to obtain, simultaneously, from the experimental ellipsometric parameters, Delta and Psi, the thickness and the complex refractive index of P(3MeTh) films grown up to 80 mC cm(-2). Thicker polymer layers are disordered and present a high degree of surface roughness. 

迎风紧致格式求解Hamilton-Jacobi方程

基于Hamilton-Jaeobi(H-J)方程和双曲型守恒律之间的关系,将三阶和五阶迎风紧致格式推广应用于求解H-J方程,建立了高精度的H-J方程求解方法.给出了一维和二维典型数值算例的计算结果,其中包括一个平面激波作用下的Richtmyer-Meshkov界面不稳定性问题.数值试验表明,在解的光滑区域该方法具有高精度,而在导数不连续的不光滑区域也获得了比较好的分辨效果.相比于同阶精度的WENO格式,本方法具有更小的数值耗散,从而有利于多尺度复杂流动的模拟中H-J方程的求解.

Crack Tip Field and J-Integral with Strain Gradient Effect

The mode I plane strain crack tip field with strain gradient effects is presented in this paper based on a simplified strain gradient theory within the framework proposed by Acharya and Bassani. The theory retains the essential structure of the incremental version of the conventional J_2 deformation theory No higher-order stress is introduced and no extra boundary value conditions beyond the conventional ones are required. The strain gradient effects are considered in the constitutive relation only through the instantaneous tangent modulus. The strain gradient measures are included into the tangent modulus as internal parameters. Therefore the boundary value problem is the same as that in the conventional theory Two typical crack Problems are studied: (a) the crack tip field under the small scale yielding condition induced by a linear elastic mode-I K-field and (b) the complete field for a compact tension specimen. The calculated results clearly show that the stress level near the crack tip with strain gradient effects is considerable higher than that in the classical theory The singularity of the strain field near the crack tip is nearly equal to the square-root singularity and the singularity of the stress field is slightly greater than it. Consequently, the J-integral is no longer path independent and increases monotonically as the radius of the calculated circular contour decreases.

Evaluación del efecto antídoto de fluxofenin sobre Digitaria Eriantha y Panicum Coloratum cv. Klein para aplicar herbicidas preemergentes

Resumen: En la región semiárida central, las gramíneas perennes megatérmicas contribuyen a disminuir los riesgos de erosión, a incrementar la receptividad en los sistemas de producción basados en pastizales naturales y a disminuir los costos de producción. Una de las especies de mayor difusión es pasto llorón (Eragrostis curvula). La resistencia a las bajas temperaturas invernales (-17°C), alta producción primaria y resistencia al pastoreo son algunas de las virtudes de esta especie. No obstante, durante el semestre frío y seco (otoño-invierno) el valor nutritivo del forraje diferido es muy bajo. La suplementación con concentrados energéticos –proteicos soluciona este problema, aunque incrementa los costos y complica el manejo. La identificación y evaluación de otras especies con características semejantes a pasto llorón, pero de mayor valor nutritivo sobre todo durante el invierno, fue una línea de trabajo importante en el INTA San Luis. De éste trabajo, surgieron dos especies actualmente en difusión en los sistemas de producción, a saber: Digitaria (Digitaria eriantha) y Mijo perenne (Panicum coloratum). Si bien la adopción de esta tecnología es importante, podría ser aún más elevada. Las dificultades de implantación es una causa relevante, sobre todo en potreros que han sido cultivados con especies anuales durante muchos años. En estos sitios, existe un importante banco de semilla de malezas gramíneas, que dificultan el control sin afectar la digitaria. El desarrollo de herbicidas preemergentes con gran poder residual, como así de compuestos químicos que funcionan como antídotos para proteger las especies que son afectadas por estos herbicidas, podrían resultar valiosos. Se dispone en el mercado de herbicidas de presiembra o preemergentes residuales formulados en base a acetamidas, a saber: i) S-metolaclor y ii) Acetoclor que controlan un amplio espectro de malezas incluidas las malezas problemas mencionadas. También se dispone de una sustancia química que funciona como antídoto-protector (fluxofenin) con el nombre comercial de Concep II y es utilizado para sembrar exitosamente el cultivo de sorgo. Se desconoce si éste compuesto podría proteger a las plántulas de digitaria y panicum. Se hipotetiza que la aplicación en el suelo de los herbicidas mencionados y la posterior siembra de semillas de digitaria y panicum protegidas con antídoto, no afectaría la germinación ni el desarrollo normal de plántulas de ambas especies. El objetivo de éste trabajo fue evaluar el efecto del antídoto, de los herbicidas y de la combinación de ambos sobre la germinación, crecimiento y sobrevivencia de plántulas de digitaria y panicum. El trabajo se desarrolló en el Laboratorio de semillas de la EEA San Luis del INTA, próxima a la ciudad de Villa Mercedes (Pcia. de San Luis). Se diseñaron 12 tratamientos con cuatro repeticiones para evaluar el efecto de cuatro dosis de antídoto (0; 20; 40 y 60 cc cada 100 kg de semilla) sin la aplicación de herbicidas (Sin), y la combinación de cada dosis de antídoto con dos herbicidas: SM (S-metolaclor) y A (Acetoclor) con la dosis recomendada comercialmente. Los tratamientos fueron: T1= (0:Sin); T2=(20:Sin); T3=(40:Sin); T4=(60:Sin); T5=(20:SM); T6=(40:SM); T7= (60:SM); T8=(20:A); T9=(40:A); T10=(60:A); T11=(0:SM); T12=(0:A). Se utilizaron 48 bandejas de plástico por especie forrajera de 15x10x3,5 cm, con 150 Se realizó la siembra al voleo con 0,5 gr de semilla en cada bandeja. Se compactó en forma semejante y cada bandeja se colocó en una bolsa de nylon para evitar la deshidratación. Luego se llevaron las 96 bandejas (2 especies forrajeras por 12 tratamientos por 4 repeticiones) a la cámara de cultivo con 30°C con 8 hs de luz y 20 °C con 16 hs de oscuridad. El ensayo tuvo una duración de 57 días. Se hicieron 14 mediciones de altura y n° de plantas. La unidad experimental fue la bandeja. Las variables respuesta (altura de hoja (mm) y el número de plantas) fueron sometidos a análisis de varianza y las medias comparadas utilizando el test de LSD. El nivel de significación utilizado en el trabajo es del 5%. Los resultados obtenidos: En Digitaria (Digitaria eriantha): I) El desarrollo y número de plantas fue mayor sin antídoto y sin herbicida, (p≤0,05) II) El tratamiento 6 (40:SM) resultó la mejor combinación para obtener un adecuado crecimiento y número de plántulas, aunque inferior al testigo (p≤0,05). III) Se logra efecto protector para el herbicida S-metolaclor con una dosis de antídoto entre 20cc y 40cc. IV) El antídoto es fitotóxico para la Digitaria Eriantha en dosis de 60cc (p≤0,05). V) El antídoto no protege a la Digitaria Eriantha en ninguna de sus dosis del herbicida Acetoclor En Mijo perenne (Panicum coloratum).: I) La aplicación de antídoto en la menor dosis (20 cc) no afectó el crecimiento ni el número de las plantas. En esta última variable, aún las dosis mayores del antídoto (40 y 60 cc) no tuvieron efectos negativos respecto al testigo (p≤0,05), II) La combinación del herbicida s-metolaclor (SM) con las dosis intermedias (20 y 40cc) de antídoto tuvo un ligero efecto negativo sobre el crecimiento y número de plantas respecto al testigo, aunque con diferencias significativas (p≤0,05) III) La aplicación del herbicida Acetoclor con todas las dosis del antídoto afectó significativamente el crecimiento y el número de plantas (p≤0,05). Se concluye que el tratamiento con antídoto en dosis bajas (20cc) no afecta el desarrollo ni el número de plantas de digitaria y panicum. Esta última especie es menos afectada que digitaria aún con mayores dosis. La mejor combinación de antídoto y herbicida SM, es de 20 cc para digitaria y 60 cc para panicum. El herbicida Acetoclor tuvo efectos negativos en ambas especies. Se recomienda realizar nuevos ensayos en condiciones reales de producción.

Convective heat dissipation with lattice-frame materials

This paper presents experimental results on heat transfer and pressure drop for a compact heat sink made of fully triangulated, lightweight (porosity∼0.938), aluminum lattice-frame materials (LFMs). Due to the inherent structural anisotropy of the LFMs, two mutually perpendicular orientations were selected for the measurements. Constant heat flux was applied to the heat sink under steady state conditions, and dissipated by forced air convection. The experimental data were compared with those predicted from an analytical model based on fin analogy. The experimental results revealed that pressure drop is strongly dependent upon the orientation of the structure, due mainly to the flow blockage effect. For heat transfer measurements, typical local temperature distributions on the substrate under constant heat flux conditions were captured with infrared camera. The thermal behavior of LFMs was found to follow closely that of cylinder banks, with early transition Reynolds number (based on strut diameter) equal to about 300. The Nusselt number prediction from the fin-analogy correlates well with experimental measurements, except at low Reynolds numbers where a slightly underestimation is observed. Comparisons with empty channels and commonly used heat exchanger media show that the present LFM heat sink can remove heat approximately seven times more efficient than an empty channel and as efficient as a bank of cylinders at the same porosity level. The aluminum LFMs are extremely stiff and strong, making them ideal candidates for multifunctional structures requiring both heat dissipation and mechanical load carrying capabilities. © 2003 Elsevier Ltd. All rights reserved.

Novel wideband active waveguide photonic crystal polarisation selector

We have designed and fabricated a broadband and compact polarisation selector using a photonic crystal at the junction of two intersecting active waveguides. The crystal shows >8dB polarisation selectivity over a 70nm range. © 2003 Optical Society of America.

High rate deposition of ta-C:H using an electron cyclotron wave resonance plasma source

A compact electron cyclotron wave resonance (ECWR) source has been developed for the high rate deposition of hydrogenated tetrahedral amorphous carbon (ta-C:H). The ECWR provides growth rates of up to 1.5 nm/s over a 4-inch diameter and an independent control of the deposition rate and ion energy. The ta-C:H was deposited using acetylene as the source gas and was characterized as having an sp3 content of up to 77%, plasmon energy of 27 eV, refractive index of 2.45, hydrogen content of about 30%, optical gap of up to 2.1 eV and RMS surface roughness of 0.04 nm. © 1999 Elsevier Science S.A. All rights reserved.

High rate deposition of Ta-C:H using an electron cyclotron wave resonance plasma source

A compact electron cyclotron wave resonance (ECWR) source has been developed for the high rate deposition of hydrogenated tetrahedral amorphous carbon (ta-C:H). The ECWR provides growth rates of up to 900 angstrom/min and an independent control of the deposition rate and ion energy. The ta-C:H was deposited using acetylene as the source gas and was characterized in terms of its bonding, stress and friction coefficient. The results indicated that the ta-C:H produced using this source fulfills the necessary requirements for applications requiring enhanced tribological performance.

The preparation, characterization and tribological properties of TA-C : H deposited using an electron cyclotron wave resonance plasma beam source

A compact electron cyclotron wave resonance (ECWR) source has been developed for the high rate deposition of hydrogenated tetrahedral amorphous carbon (ta-C:H). The ECWR provides growth rates of up to 900 Å/min over a 4″ diameter and an independent control of the deposition rate and ion energy. The ta-C:H was deposited using acetylene as the source gas and was characterized in terms of its sp3 content, mass density, intrinsic stress, hydrogen content, C-H bonding, Raman spectra, optical gap, surface roughness and friction coefficient. The results obtained indicated that the film properties were maximized at an ion energy of approximately 167 eV, corresponding to an energy per daughter carbon ion of 76 eV. The relationship between the incident ion energy and film densification was also explained in terms of the subsurface implantation of carbon ions into the growing film.