A possible alchemist apparatus from the early islamic period excavated at Ramla, Israel

Abstract: During extensive salvage excavations carried out during the years 2004-2008 in a large Early Islamic industrial area at the vicinities of Ramla, in Central Israel, an unparalleled industrial device was unearthed. The star-shaped, soil embedded installation, whose lower part was preserved, consisted of a central pottery jar surrounded by five minor jars, linked by ceramic pipes. Evidence of heat was observed mainly around the central vessel, and metal hollow cones perforated in the tip were found inside the surrounding jars. Although the manufacturing procedures and operation techniques of the installation are not completely clear, it is proposed that the installation is part of an industrial workshop or an alchemy laboratory. Both industry and alchemy were well-developed during the Early Islamic period and very often closely related, to the point that sometimes it is difficult to distinguish between them. The identification proposed is based on comparisons with tools described in literary sources, and somewhat later drawings and etchings. Circumstantial ceramic evidence was found, as well as the proximity of a bathhouse whose guests could have been the consumers of perfumes and unguents seem to reinforce this possibility. Due to the poor state of preservation of the device and the lack of available comparisons, the identification proposed here is tentative, and future research coupled with eventual new discoveries is needed in order to clarify this matter.

Ramesside, Late Nubian and christian pottery from Serra West in the Museum of Natural History, La Plata

Resumen: El Museo de Ciencias Naturales de La Plata, Argentina, posee una colección de piezas cerámicas provenientes del asentamiento egipcio y de la iglesia de Aksha, y de las tumbas nubias de Serra Oeste, sobre la margen izquierda del Nilo en la Baja Nubia, que pertenecen a las culturas meroítica y del Grupo X. Esta colección es producto del reparto después de las excavaciones realizadas por la Expedición Franco-Argentina en Sudán entre 1961 y 1963, como parte de las campañas de la UNESCO para salvar los monumentos de Nubia.

A nanoindentation analysis of the effects of microstructure on elastic properties of Al2O3/SiC composites

Nanoindentation tests were carried out to investigate certain elastic properties of Al2O3/SiCp composites at microscopic scales (nm up to mu m) and under ultra-low loads from 3 mN to 250 mN, with special attention paid to effects caused by SiC particles and pores. The measured Young's modulus depends on the volume fraction of SiC particles and on the composite porosity and it can compare with that of alumina. The Young's modulus exhibits large scatters at small penetrations, but it tends to be constant with lesser dispersion as the indentation depth increases. Further analysis indicated that the scatter results from specific microstructural heterogeneities. The measured Young's moduli are in agreement with predictions, provided the actual role of the microstructure is taken into account. (C) 2007 Elsevier Ltd. All rights reserved.

Energy principle of ferroelectric ceramics and single domain mechanical model

Many physical experiments have shown that the domain switching in a ferroelectric material is a complicated evolution process of the domain wall with the variation of stress and electric field. According to this mechanism, the volume fraction of the domain switching is introduced in the constitutive law of ferroelectric ceramic and used to study the nonlinear constitutive behavior of ferroelectric body in this paper. The principle of stationary total energy is put forward in which the basic unknown quantities are the displacement u (i) , electric displacement D (i) and volume fraction rho (I) of the domain switching for the variant I. Mechanical field equation and a new domain switching criterion are obtained from the principle of stationary total energy. The domain switching criterion proposed in this paper is an expansion and development of the energy criterion. On the basis of the domain switching criterion, a set of linear algebraic equations for the volume fraction rho (I) of domain switching is obtained, in which the coefficients of the linear algebraic equations only contain the unknown strain and electric fields. Then a single domain mechanical model is proposed in this paper. The poled ferroelectric specimen is considered as a transversely isotropic single domain. By using the partial experimental results, the hardening relation between the driving force of domain switching and the volume fraction of domain switching can be calibrated. Then the electromechanical response can be calculated on the basis of the calibrated hardening relation. The results involve the electric butterfly shaped curves of axial strain versus axial electric field, the hysteresis loops of electric displacement versus electric filed and the evolution process of the domain switching in the ferroelectric specimens under uniaxial coupled stress and electric field loading. The present theoretic prediction agrees reasonably with the experimental results given by Lynch.

Ballistic impact of ceramics

The impact behaviour of a range of glass and ceramic materials has been studied using high-speed photography. A gas gun was used to project hardened spheres at plate specimens in the velocity range 30 to 1000m s-1. The target materials included soda-lime glass, boron carbide and various glass ceramics and aluminas. The performance of a particular ceramic was found to depend on a combination of parameters but of key importance was the relative hardness of the projectile and target materials. The fracture toughness, K(IC), had only a secondary effect.

钢基铝镀层转化为陶瓷层的演变规律研究

热浸镀铝钢经等离子体电解氧化（Plasma Electrolytic Oxidation,PEO）处理后,表面铝镀层转化为陶瓷层.实验对阳极电压变化、陶瓷层生长规律、涂层截面形貌和成分等进行了研究.结果表明：在PEO初期,热浸铝试件的阳极电压变化趋势与纯铝试件相同,在PEO后期电压有下降趋势.铝镀层消耗和陶瓷层厚度增长近似为线性变化.当铝镀层完全陶瓷化后,FeAl层参与PEO反应,但陶瓷层生长速率变慢,在界面处出现大量裂纹;陶瓷层主要成分为Al、Si、O元素,相结构主要为γ-Al_2O_3与莫来石相,在PEO后期出现α-Al_2O_3相.复合陶瓷层硬度呈区域性分布,陶瓷层最高硬度可达HV1800.

热浸铝钢等离子体电解氧化陶瓷层的微观力学特性

采用纳米压入方法表征了热浸镀铝钢表面由Al2O3层、Al层和FeAl层组成的复合涂层的纳米硬度、弹性模量及断裂韧性等微观力学性能，采用扫描电镜（SEM）观察了纳米压痕形貌，并分析了孔洞对陶瓷层的纳米压入行为和压痕裂纹扩展的影响．结果表明：等离子体电解氧化（PEO）陶瓷层中包含许多微米和亚微米尺度的细小孔洞，陶瓷层弹性模量约为226．4 GPa，纳米硬度约为19．6 GPa．当纳米压入深度为250nm时，所测得陶瓷层的力学参数分散性较大．与FeAl层比较，PEO陶瓷层具有较高的裂纹扩展阻力．FeAl层纳米压痕顶端产生了沿直线扩展的径向裂纹；而陶瓷层纳米压痕中除径向裂纹外出现了侧边裂纹．

Shell midden people in northern Iberia. New data from the mesolithic rock shelter of J3 (Basque Country, Spain)

[EN]In the course of a sondage dug in the rock shelter of J3, in the Jaizkibel mountains (at the north-western tip of Guipúzcoa), the body of a adult man was located buried inside a shell midden. This shell midden had not been disturbed and presented internal stratigraphy features. In any case, the outer edge of the shell midden does show some interesting interdigitation with the adjacent habitational layers, with evidence of different stages of occupation. Within the shell midden itself, under the individual buried there, it was possible to observe layers without any ceramics, whereas the layers covering said individual included ceramic fragments. This individual has been dated to 8,300 BP and therefore corresponds to a Mesolithic context.

Formation and Structure of Composite Coating of HAD and Micro-Plasma Oxidation on A3 Steel

Composite coatings were obtained on A3 steel by hot dipping aluminum(HAD) at 720 degreesC for 6 min and micro-plasma oxidation (MPO) in alkali electrolyte. The surface morphology, element distribution and interface structure of composite coatings were studied by means of XRD, SEM and EDS. The results show that the composite coatings obtained through HAD/MPO on A3 steel consist of four layers. From the surface to the substrate, the layer is loose Al2O3 ceramic, compact Al2O3 ceramic, At and FeAl intermetallic compound layer in turn. The adhesions among all the layers are strengthened because the ceramic layer formed at the At surface originally, FeAl intermetallic compound layer and substrate are combined in metallurgical form through mutual diffusion during HAD process. Initial experiment results disclose that the anti-corrosion performance and wear resistance of composite coating are obviously improved through HAD/MPO treatment.

BONDING OF ALUMINA AND METAL USING BULK METALLIC GLASS FORMING ALLOY

Metal-alumina joints have found various practical applications in electronic devices and high technology industry. However, making of sound metal ceramic brazed couple is still a challenge in terms of its direct application in the industry. In this work we successfully braze copper with Al2O3 ceramic using Zr52.5Cu17.9Ni14.6Al10Ti5 bulk metallic glass forming alloy as filler alloy. The shear strength of the joints can reach 140 MPa, and the microstructrural analysis confirms a reliable chemical boning of the interface. The results show that the bulk metallic glass forming alloys with high concentration of active elements are prospective for using as filler alloy in metal-ceramic bonding.

Interface cracking and particulate size effect in particle-reinforced metal-matrix composites

The mechanical behaviors of the ceramic particle-reinforced metal matrix composites are modeled based on the conventional theory of mechanism-based strain gradient plasticity presented by Huang et al. Two cases of interface features with and without the effects of interface cracking will be analyzed, respectively. Through comparing the result based on the interface cracking model with experimental result, the effectiveness of the present model can be evaluated. Simultaneously, the length parameters included in the strain gradient plasticity theory can be obtained.

基于跨尺度模型的界面研究

探索和建立不同尺度理论之间的关联模式是科学研究的重要课题，本文基于跨尺度模型着重探讨了金属陶瓷界面的凝聚能和原子结构问题。本文遵循原始Peierls-Nabarro模型的基本思想，提出了一种处理一维界面失配位错组的新方法。在这个推广的Peierls-Nabarro模型中，本文得到了一个简单而且准确的解析解，此解反映了失配位错的核结构、能量与失配度、剪切模量之间的依赖关系。当界面剪切模量较强而失配度较小时，界面的结构可以用一组奇导师Volterra位错来描述，这与一些原子模拟结果一致。采用这一简单的模型，引入第一原理计算得到的数据，此模型可以估算金属陶瓷界面的凝聚能。一维界面失配位错组的Peierls-Nabarro模型还被解析推广描述一大类较宽的位错。在模型中我们引进了一个参数a，通过控制参数a，我们可以系统地改变失配位错芯的宽度、剪切应力的分布和弹性恢复力。随着a增加，位错宽度增加，同时弹性恢复力和失配位错应力的幅度减少。当界面剪切模量强和失配度小时，失配位错的宽度近似线性反比于弹性恢复力的幅度大小。同时当界面剪切模量和失配度固定时，失配能、弹性能和总的界面能随a的增加而减少。界面能和恢复力律形式密切相关，当界面剪切模量弱和失配度大时，这种依赖关系更强。考虑到界面常常是在晶格两个方向都有失配，本文还引进了描述界面周期失配位错的二维广义Peierls-Nabarro模型，使得我们能够定量地研究界面的结构和能量。文中定量分析了广义堆垛能γ面对界面失配位错的结构和能量的影响，分析了位错网中两种位错组的相互作用。当界面剪切模量τ_0变大和失配度f变小时，随着位错核区占整个界面的比重下降，γ面的形状对界面能量和结构影响减弱，结果两种位错组之间的相互作用也减弱。此外γ面的变化还有可能导致位错网结构的转变，也就是导致界面结构的转变。应用此模型，本文还研究了金属－陶瓷Ag/MgO(100)界面，给出了界面的能量和原子结构。文中得出结论：在Ag/MgO(100)界面将会形成{1/2<110>; <110>}类型的位错网。此外由于界面失配位错的形成，Ag/MgO(100)界面凝聚能的理论值900mJ/m~2将减少214mJ/m~2，最终成为686mJ/m~2。基于第一原理赝势平面波的总能计算，文中给出了金属陶瓷Al/MgO(100)界面弛豫和未弛豫时的广义堆垛能面。然后结合第三章发展的广义二维Peierls-Nabarro模型，详细研究了金属陶瓷Al/MgO(100)界面的原子结构和界面能。文中得出的“在Al/MgO(100)界面将会形成{1/2<110>; <110>}类型位错网”的推论，证实了Vellinga等的猜测；文中还预测了凝聚能的理论是在600mJ/m~2（未弛豫情形）和670mJ/m~2（弛豫情形）之间。这个应用表明此方法能够容易地建立连续介质理论和第一原理计算之间的联系，实现理论上的跨尺度。本文最后提出了一种得到界面原子有效对势的反演方法。通过反演金属－MgO陶瓷界面的第一原理计算的凝聚能曲线，我们得到了一些金属原子和陶瓷离子之间的对势，此对势反映了金属陶瓷键合的特性。本文的反演方法提供了通过第一原理计算数据来拟合界面原子对势的一种可行性途径。这种方法可归结为第一类尺度关联理论，即单向的跨尺度关联模式。

带压电陶瓷片梁的力学分析和二类变量广义变分原理

对于采用贴有压电陶瓷片作为作动元件的智能结构，在进行自适应控制时，往往要分析压电陶瓷片所引起的结构中的应力、应变和位移。对于带有压电陶瓷片梁的力学分析，文献中大多采用Euler-Bernoulli模型，即不考虑梁中的剪力，且假定梁沿厚度方向满足直法线假定。考虑到压电陶瓷片对梁的作用主要是通过粘贴层以剪力的形式传递到梁上，梁截面上的剪应力和剪应变一般很大，其影响不能忽略。本文采用Hellinger-Reissner二类变分广义余能原理，导出考虑梁截面上剪应力和剪应变影响的方程式，其中采用吉尔法求解非齐次常微分方程组。并将求得的解与相同条件的有限元解进行比较。结果证明该方法很有效。本文还对二类广义变分法进行了一般的讨论，发现，在使用二类广义变分法求解时，随着应力和位移所取项数的增加，结果有时反而变坏。并对二类广义变分法的使用提出了一些建议。

Bonding Of Alumina And Metal Using Bulk Metallic Glass Forming Alloy

Metal-alumina joints have found various practical applications in electronic devices and high technology industry. However, making of sound metal ceramic brazed couple is still a challenge in terms of its direct application in the industry. In this work we successfully braze copper with Al2O3 ceramic using Zr52.5Cu17.9Ni14.6Al10Ti5 bulk metallic glass forming alloy as filler alloy. The shear strength of the joints can reach 140 MPa, and the microstructrural analysis confirms a reliable chemical boning of the interface. The results show that the bulk metallic glass forming alloys with high concentration of active elements are prospective for using as filler alloy in metal-ceramic bonding.