Trips and their CO2 emissions induced by a shopping center

Most previous studies have focused on entire trips in a geographic region, while a few of them addressed trips induced by a city landmark. Therefore paper explores trips and their CO2 emissions induced by a shopping center from a time-space perspective and their usage in relocation planning. This is conducted by the means of a case study in the city of Borlänge in mid-Sweden where trips to the city’s largest shopping mall in its center are examined. We use GPS tracking data of car trips that end and start at the shopping center. Thereafter, (1) we analyze the traffic emission patterns from a time-space perspective where temporal patterns reveal an hourly-based traffic emission dynamics and where spatial patterns uncover a heterogeneous distribution of traffic emissions in spatial areas and individual street segments. Further, (2) this study reports that most of the observed trips follow an optimal route in terms of CO2 emissions. In this respect, (3) we evaluate how well placed the current shopping center is through a comparison with two competing locations. We conclude that the two suggested locations, which are close to the current shopping center, do not show a significant improvement in term of CO2 emissions.

Optimal retail location and CO2 emissions

In this paper, the p-median model is used to find the location of retail stores that minimizes CO2 emissions from consumer travel. The optimal location is then compared with the existing retail location,and the excess CO2 emissions compared with the optimal solution is calculated. The results show that by using the environmentally optimal location, CO2 emissions from consumer travel could be reduced by approximately 25percent. 

Measuring CO2 emissions induced by online and brick-and-mortar retailing

We develop a method for empirically measuring the difference in carbon footprint between traditional and online retailing (“e-tailing”) from entry point to a geographical area to consumer residence. The method only requires data on the locations of brick-and-mortar stores, online delivery points, and residences of the region’s population, and on the goods transportation networks in the studied region. Such data are readily available in most countries, so the method is not country or region specific. The method has been evaluated using data from the Dalecarlia region in Sweden, and is shown to be robust to all assumptions made. In our empirical example, the results indicate that the average distance from consumer residence to a brick-and-mortar retailer is 48.54 km in the studied region, while the average distance to an online delivery point is 6.7 km. The results also indicate that e-tailing increases the average distance traveled from the regional entry point to the delivery point from 47.15 km for a brick-and-mortar store to 122.75 km for the online delivery points. However, as professional carriers transport the products in bulk to stores or online delivery points, which is more efficient than consumers’ transporting the products to their residences, the results indicate that consumers switching from traditional to e-tailing on average reduce their CO2 footprints by 84% when buying standard consumer electronics products. 

Measuring CO2 emissions induced by online and brick-and-mortar retailing

We develop a method for empirically measuring the difference in carbon footprint between traditional and online retailing (“e-tailing”) from entry point to a geographical area to consumer residence. The method only requires data on the locations of brick-and-mortar stores, online delivery points, and residences of the region’s population, and on the goods transportation networks in the studied region. Such data are readily available in most countries, so the method is not country or region specific. The method has been evaluated using data from the Dalecarlia region in Sweden, and is shown to be robust to all assumptions made. In our empirical example, the results indicate that the average distance from consumer residence to a brick-and-mortar retailer is 48.54 km in the studied region, while the average distance to an online delivery point is 6.7 km. The results also indicate that e-tailing increases the average distance traveled from the regional entry point to the delivery point from 47.15 km for a brick-and-mortar store to 122.75 km for the online delivery points. However, as professional carriers transport the products in bulk to stores or online delivery points, which is more efficient than consumers’ transporting the products to their residences, the results indicate that consumers switching from traditional to e-tailing on average reduce their CO2 footprints by 84% when buying standard consumer electronics products. 

Suco de laranja e vitamina C : efeito sobre a estabilidade genômica

Existem evidências crescentes indicando a associação entre dietas ricas em frutas e vegetais e a diminuição da incidência de câncer. O suco de laranja (OJ) pode ser incluído entre os alimentos com potencial quimioprotetor e seu estudo é muito relevante pelo amplo consumo desta bebida. O OJ possui vários nutrientes e compostos bioativos com atividades antioxidante, antimutagênica, anticarcinogênica e antiaterogênica, entre outras. A vitamina C (Vit C) é um dos nutrientes mais abundantes no OJ, e o único nutriente que pode ser provido em quantidade superior à recomendação diária por uma única porção de 200 mL de OJ. A Vit C, a exemplo de outros componentes do OJ, pode ser tanto benéfica quanto maléfica para os sistemas biológicos, dependendo do contexto metabólico. Neste sentido, vários nutrientes presentes no OJ têm sido identificados como mutagênicos ou carcinogênicos, especialmente quando administrados de forma isolada. Este estudo utilizou o ensaio Cometa alcalino em sangue de camundongos (in vivo) para avaliar: 1) a genotoxicidade do OJ e da Vit C; 2) a genotoxicidade do FeSO4 e do CuSO4: 3) o efeito modulador do OJ e da Vit C sobre a genotoxicidade do FeSO4 e CuSO4, bem como do metilmetanosulfonato (MMS) e da ciclofosfamida (CP). A versão alcalina do ensaio Cometa foi utilizada para avaliar o dano no DNA em células brancas do sangue periférico de camundongos. Adicionalmente, os níveis de cobre e ferro no sangue e no fígado dos camundongos tratados com metais e OJ foram avaliados pela metodologia de PIXE (Particle-Induced X-ray Emission). Grupos com pelo menos 6 camundongos (metade de cada sexo) foram tratados por gavage com uma ou duas doses de água (controle), CP, MMS, FeSO4 ou CuSO4. OJ (0.1 mL/Kg) foi administrado tanto antes (pré-tratamento) quanto após a administração das substâncias-teste (pós-tratamento). A Vit C (1 e 30 mg/Kg) foi administrada apenas no pós-tratamento. O dano no DNA foi avaliado 24 e 48 h após o início do tratamento. Após 24 h, o OJ induziu um suave aumento no dano no DNA, enquanto a Vit C foi genotóxica (30 mg/Kg > 1 mg/Kg). O tratamento duplo com Vit C (a 0 e a 24 h) induziu uma resposta genotóxica cumulativa a 48 h, que foi mais intensa para a dose maior. O FeSO4 e o CuSO4 foram genotóxicos após 24 h, mas tiveram seu dano efetivamente reparado após 48 h do tratamento. O pré-tratamento com OJ reduziu a genotoxicidade do FeSO4 e do CuSO4 (efeito preventivo). O pós-tratamento com OJ também reduziu a genotoxicidade do CuSO4 (efeito reparador). O OJ mostrou tanto efeito preventivo quanto reparador sobre a genotoxicidade do MMS. O OJ teve apenas efeito reparador sobre a CP. Ambas doses de Vit C aumentaram os danos no DNA causados pelo FeSO4 e pelo CuSO4. Adicionalmente, os níveis de cobre e ferro no sangue e no fígado dos camundongos tratados com metais e OJ foram avaliados pela metodologia de PIXE (Particle-Induced X-ray Emission). Grupos com pelo menos 6 camundongos (metade de cada sexo) foram tratados por gavage com uma ou duas doses de água (controle), CP, MMS, FeSO4 ou CuSO4. OJ (0.1 mL/Kg) foi administrado tanto antes (pré-tratamento) quanto após a administração das substâncias-teste (pós-tratamento). A Vit C (1 e 30 mg/Kg) foi administrada apenas no pós-tratamento. O dano no DNA foi avaliado 24 e 48 h após o início do tratamento. Após 24 h, o OJ induziu um suave aumento no dano no DNA, enquanto a Vit C foi genotóxica (30 mg/Kg > 1 mg/Kg). O tratamento duplo com Vit C (a 0 e a 24 h) induziu uma resposta genotóxica cumulativa a 48 h, que foi mais intensa para a dose maior. O FeSO4 e o CuSO4 foram genotóxicos após 24 h, mas tiveram seu dano efetivamente reparado após 48 h do tratamento. O pré-tratamento com OJ reduziu a genotoxicidade do FeSO4 e do CuSO4 (efeito preventivo). O pós-tratamento com OJ também reduziu a genotoxicidade do CuSO4 (efeito reparador). O OJ mostrou tanto efeito preventivo quanto reparador sobre a genotoxicidade do MMS. O OJ teve apenas efeito reparador sobre a CP. Ambas doses de Vit C aumentaram os danos no DNA causados pelo FeSO4 e pelo CuSO4. processado e armazenado de forma a preservar o seu potencial biológico é um alimento sugerido como uma das porções de uma dieta equilibrada (contendo pelo menos 5 porções de frutas e vegetais), recomendada para uma vida saudável e longeva.

Sinterização de Ce1-XEuXO2-(X/2) para aplicação como eletrólito sólido em células a combustível de temperaturas intermediárias

Given the environmental concern over global warming that occurs mainly by emission of CO2 from the combustion of petroleum, coal and natural gas research focused on alternative and clean energy generation has been intensified. Among these, the highlight the solid oxide fuel cell intermediate temperature (IT-SOFC). For application as electrolyte of the devices doped based CeO2 with rare earth ions (TR+ 3) have been quite promising because they have good ionic conductivity and operate at relatively low temperatures (500-800 ° C). In this work, studied the Ce1-xEuxO2-δ (x = 0,1, 0,2 and 0,3), solid solutions synthesized by the polymeric precursor method to be used as solid electrolyte. It was also studied the processing steps of these powders (milling, compaction and two step sintering) in order to obtain dense sintered pellets with reduced grain size and homogeneous microstructure. For this, the powders were characterized by thermal analysis, X-ray diffraction, particle size distribution and scanning electrons microscopy, since the sintered samples were characterized by dilatometry, scanning electrons microscopy, density and grain size measurements. By x-ray diffraction, it was verified the formation of the solid solution for all compositions. Crystallites in the nanometric scale were found for both sintering routes but the two step sintering presented significant reduction in the average grain size

Al-based anodic oxide films structure observation using field emission gun scanning electron microscopy

In the present work, the anodic oxide films of Al, Al-Cu 4.5% and Al-Si 6.5% alloys are formed using direct and pulse current. In the case of Al-Cu and Al-Si alloys, the electrolyte used contains sulfuric acid and oxalic acid, meanwhile for Al the electrolyte contains sulfuric acid only. Al-Cu alloy was submitted to a heat treatment in order to decrease the effect of inter metallic phase theta upon the anodic film structure. Fractured samples were observed using a field emission gun scanning electron microscope JSM-6330F at (LME)/Brazilian Synchrotron Light Laboratory (LNLS), Campinas, SP, Brazil. The oxide film images enable evaluation of the pore size and form with a resolution similar to the transmission electron microscope (TEM) resolution. It is also observed that the anodizing process using pulse current produces an irregular structure of pore walls, and by direct cur-rent it is produced a rectilinear pore wall. (c) 2005 Elsevier B.V. All rights reserved.

Taxa de emissão de CO2 de um latossolo fertirrigado com ácido fosfórico por gotejamento

A aplicação de fertilizantes fosfatados por meio de fertirrigação com sistemas de irrigação localizada pode causar obstrução de emissores. Para evitar esse problema, pode ser utilizado o ácido fosfórico como fonte de fósforo às plantas. Porém, têm sido pouco investigados os efeitos da irrigação relacionados às perdas de CO2 do solo para a atmosfera, em conseqüência da decomposição do carbono orgânico e da infiltração de água no solo. Neste trabalho, investigou-se, no período de um mês, o efeito da fertirrigação com ácido fosfórico nas taxas de emissão de CO2 de um latossolo desprovido de vegetação, na Área Experimental de Irrigação da UNESP, Câmpus de Jaboticabal - SP. Utilizou-se de um sistema de irrigação por gotejamento, com delineamento experimental em blocos casualizados, constando de cinco repetições e cinco tratamentos (0; 30; 60; 90 e 120 kg ha-1de P2O5), aplicados via fertirrigação com ácido fosfórico. Verificou-se que as taxas de emissão de CO2 aumentaram significativamente após as fertirrigações, porém não houve efeito da dose do ácido fosfórico sobre as taxas. A umidade do solo mostrou-se um fator importante na relação entre as variações das taxas de emissão e a temperatura do solo ao longo do período estudado.

Extração do óleo essencial de Cymbopogom winterianus J. com CO2 pressurizado

The extraction with pressurized fluids has become an attractive process for the extraction of essential oils, mainly due the specific characteristics of the fluids near the critical region. This work presents results of the extraction process of the essential oil of Cymbopogon winterianus J. with CO2 under high pressures. The effect of the following variables was evaluated: solvent flow rate (from 0.37 to 1.5 g CO2/min), pressure (66.7 and 75 bar) and temperature (8, 10, 15, 20 and 25 ºC) on the extraction kinetics and the total yield of the process, as well as in the solubility and composition of the C. winterianus essential oil. The experimental apparatus consisted of an extractor of fixed bed and the dynamic method was adopted for the calculation of the oil solubility. Extractions were also accomplished by conventional techniques (steam and organic solvent extraction). The determination and identification of extract composition were done by gas chromatography coupled with a mass spectrometer (GC-MS). The extract composition varied in function of the studied operational conditions and also related to the used extraction method. The main components obtained in the CO2 extraction were elemol, geraniol, citronellol and citronellal. For the steam extraction were the citronellal, citronellol and geraniol and for the organic solvent extraction were the azulene and the hexadecane. The most yield values (2.76%) and oil solubility (2.49x10-2 g oil/ g CO2) were obtained through the CO2 extraction in the operational conditions of T = 10°C, P = 66.7 bar and solvent flow rate 0.85 g CO2/min

Liberação de CO2, biomassa microbiana e fósforo disponível em solo adicionado de matéria seca de poaia-branca

O presente experimento, inteiramente casualizado, foi desenvolvido em condições de laboratório no Departamento de Defesa Fitossanitária, FCA/UNESP - Botucatu, entre julho e setembro de 1992. Amostras de Areia Quartzosa equivalentes à 40 g de terra seca à 105 oC ± 2 com ou sem adição de 1,9 g de matéria seca de plantas de poaia-branca (Richardia brasiliensis), 0,19 g de nitrogênio (NH4)2SO4 e 0,88 g de apatita de Araxá, foram incubadas no escuro a 25 o C ± 2 , com umidade mantida a 60% da capacidade de retenção de água. Durante a incubação, determinou-se o CO2 liberado, utilizando-se o método de retenção em NAOH seguida de titulometria com HCl; a biomassa microbiana, método de fumigação-incubação; o pH e a quantidade de fósforo extraído por resina. A maior liberação de CO2 ocorreu durante os dez primeiros dias de incubação, com 77% do total de carbono liberado nos tratamentos com adição de poaia, e 37% nos tratamentos sem adição da mesma. A liberação de CO2 foi 57 vezes maior nos tratamentos com poaia em relação ao controle. A poaia também provocou aumentos na biomassa microbiana (média de 8 vezes a biomassa do tratamento controle), e a adição de nitrogênio e/ou fosfato de rocha junto à poaia antecipou os picos de formação de biomassa de 20 para 10 dias de incubação. Os níveis de fósforo disponível foram maiores no tratamento com adição de fosfato de rocha apenas. A poaia também alcalinizou o sistema, não permitindo desta forma, observar-se relação significativa entre pH e teor de fósforo disponível.

Avaliação da capacidade de adsorção do CO2 em zeólita 12X com gases sintéticos e originados da pirólise do lodo de esgoto

This work depicts a study of the adsorption of carbon dioxide on zeolite 13X. The activities were divided into four stages: study batch adsorption capacity of the adsorbent with synthetic CO2 (4%), fixed bed dynamic evaluation with the commercial mixture of gases (4% CO2, 1.11% CO, 1 2% H2, 0.233% CH4, 0.1% C3, 0.0233% C4 argon as inert closing balance), fixed bed dynamic modeling and evaluation of the breakthrough curve of CO2 originated from the pyrolysis of sewage sludge. The sewage sludge and the adsorbent were characterized by analysis TG / DTA, SEM, XRF and BET. Adsorption studies were carried out under the following operating conditions: temperature 40 °C (for the pyrolysis of the sludge T = 600 °C), pressures of 0.55 to 5.05 bar (batch process), flow rate of the gaseous mixture between 50 - 72 ml/min and the adsorbent masses of 10, 15 and 20 g (fixed bed process). The time for the adsorption batch was 7 h and on the fixed bed was around 180 min. The results of this study showed that in batch adsorption process step with zeolite 13X is efficient and the mass of adsorbed CO2 increases with the increases pressure, decreases with temperature increases and rises due the increase of activation temperature adsorbent. In the batch process were evaluated the breakthrough curves, which were compared with adsorption isotherms represented by the models of Langmuir, Freündlich and Toth. All models well adjusted to the experimental points, but the Langmuir model was chosen in view of its use in the dynamic model does not have implications for adsorption (indeterminacy and larger number of parameters such as occurred with others) in solving the equation. In the fixed bed dynamic study with the synthetic gas mixture, 20 g of mass adsorbent showed the maximum adsorption percentage 46.7% at 40 °C temperature and 50 mL/min of flow rate. The model was satisfactorily fitted to the three breakthrough curves and the parameters were: axial dispersion coefficient (0.0165 dm2/min), effective diffusivity inside the particle (dm2/min 0.0884) and external transfer coefficient mass (0.45 dm/min). The breakthrough curve for CO2 in the process of pyrolysis of the sludge showed a fast saturation with traces of aerosols presents in the gas phase into the fixed bed under the reaction process

Order-disorder degree of self-assembled clusters: Influence on photoluminescence emission and morphology of BaxSr1-xTiO3 nanocrystals

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Different origins of green-light photoluminescence emission in structurally ordered and disordered powders of calcium molybdate

A strong greenish-light photoluminescence (PL) emission was measured at room temperature for disordered and ordered powders of CaMoO4 prepared by the polymeric precursor method. The structural evolution from disordered to ordered powders was accompanied by XRD. Raman spectroscopy, and TEM imagery. High-level quantum mechanical calculations in the density functional framework were used to interpret the formation of the structural defects of disorder powders in terms of band diagram and density of states. Complex cluster vacancies [MoO3 center dot V-O(z)] and [CaO7 center dot V-O(z)] (where V-O(z) = V-O(X), V-O(center dot), V-O(center dot center dot)) were suggested to be responsible to the appearance of new states shallow and deeply inserted in the band gap. These defects give rise to the PL in disordered powders. The natural PL emission of ordered CaMoO4 was attributed to an intrinsic slight distortion of the [MoO4] tetrahedral in the short range.

In-process grinding monitoring by acoustic emission

This work aims to investigate the efficiency of digital signal processing tools of acoustic emission signals in order to detect thermal damages in grinding process. To accomplish such a goal, an experimental work was carried out for 15 runs in a surface grinding machine operating with an aluminum oxide grinding wheel and ABNT 1045. The acoustic emission signals were acquired from a fixed sensor placed on the workpiece holder. A high sampling rate data acquisition system at 2.5 MHz was used to collect the raw acoustic emission instead of root mean square value usually employed. Many statistics have shown effective to detect burn, such as the root mean square (RMS), correlation of the AE, constant false alarm (CFAR), ratio of power (ROP) and mean-value deviance (MVD). However, the CFAR, ROP, Kurtosis and correlation of the AE have been presented more sensitive than the RMS.

Ecological efficiency in thermoelectric power plants

This work evaluates the environmental impact resulting from the natural gas and diesel combustion in thermoelectric power plants that utilize the combined cycle technology (CC), as regarding to Brazilian conditions according to Thermopower Priority Plan JPP). In the regions where there are not natural gas the option has been the utilization of diesel and consequentily there are more emission of pollutants. The ecological efficiency concept, which evaluates by and large the environmental impact, caused by CO2, SO2, NOx and particulate matter (PM) emissions. The combustion gases of the thermoelectric power plants working with natural gas (less pollutant) and diesel (more pollutant) cause problems to the environment, for their components harm the human being life, animals and directly the plants. The resulting pollution from natural gas and diesel combustion is analyzed, considering separately the CO2, SO2, NO2 and particulate matter gas emission and comparing them with the in use international standards regarding the air quality. It can be concluded that it is possible to calculate thermoelectric power plant quantitative and qualitative environment factor, and on the ecological standpoint, for plant with total power of 41441 kW, being 27 170 kW for the gas turbine and 14271 kW for the steam turbine. The natural gas used as fuel is better than the diesel, presenting ecological efficiency of 0.944 versus 0.914 for the latter, considering a thermal efficiency of 54% for the combined cycle. (c) 2006 Elsevier Ltd. All rights reserved.