Analysis and modelling of chemical looping combustion process with and without oxygen uncoupling

Effective control and limiting of carbon dioxide (CO₂) emissions in energy production are major challenges of science today. Current research activities include the development of new low-cost carbon capture technologies, and among the proposed concepts, chemical combustion (CLC) and chemical looping with oxygen uncoupling (CLOU) have attracted significant attention allowing intrinsic separation of pure CO₂ from a hydrocarbon fuel combustion process with a comparatively small energy penalty. Both CLC and CLOU utilize the well-established fluidized bed technology, but several technical challenges need to be overcome in order to commercialize the processes. Therefore, development of proper modelling and simulation tools is essential for the design, optimization, and scale-up of chemical looping-based combustion systems. The main objective of this work was to analyze the technological feasibility of CLC and CLOU processes at different scales using a computational modelling approach. A onedimensional fluidized bed model frame was constructed and applied for simulations of CLC and CLOU systems consisting of interconnected fluidized bed reactors. The model is based on the conservation of mass and energy, and semi-empirical correlations are used to describe the hydrodynamics, chemical reactions, and transfer of heat in the reactors. Another objective was to evaluate the viability of chemical looping-based energy production, and a flow sheet model representing a CLC-integrated steam power plant was developed. The 1D model frame was succesfully validated based on the operation of a 150 kWth laboratory-sized CLC unit fed by methane. By following certain scale-up criteria, a conceptual design for a CLC reactor system at a pre-commercial scale of 100 MWth was created, after which the validated model was used to predict the performance of the system. As a result, further understanding of the parameters affecting the operation of a large-scale CLC process was acquired, which will be useful for the practical design work in the future. The integration of the reactor system and steam turbine cycle for power production was studied resulting in a suggested plant layout including a CLC boiler system, a simple heat recovery setup, and an integrated steam cycle with a three pressure level steam turbine. Possible operational regions of a CLOU reactor system fed by bituminous coal were determined via mass, energy, and exergy balance analysis. Finally, the 1D fluidized bed model was modified suitable for CLOU, and the performance of a hypothetical 500 MWth CLOU fuel reactor was evaluated by extensive case simulations.

A biolistic process for in vitro gene transfer into chicken embryos

Chicken embryos kept in culture medium were bombarded using a high helium gas pressure biolistic device. To optimize the factors that affect transformation efficiency, the lacZ gene under control of the human cytomegalovirus immediate early enhancer/promoter was used as a reporter gene. There was an inverse relationship between survival rate and transformation efficiency. The best conditions obtained for high embryo survival and high transformation efficiency were achieved with 800 psi helium gas pressure, 500 mmHg vacuum, gold particles, an 8 cm DNA-coated microparticle flying distance to the embryo and embryo placement 0.5 cm from the center of the particle dispersion cone. Under these conditions, transformation efficiency was 100%, survival rate 25% and the number of expression units in the embryo body cells ranged from 100 to 1,000. Expression of green fluorescent protein was also detected in embryos bombarded under optimal conditions. Based on the results obtained, the biolistic process can be considered an efficient method for the transformation of chicken embryos and therefore can be used as a model system to study transient gene expression and tissue-specific promoters.

Development of category planning process in construction business

The aim of this thesis was to develop the category planning process in the case company operating in construction industry. As the interest in the field of research has just recently started to emerge towards the benefits of category management and planning, the theoretical background was derived from literature of subjects with a relation to category planning i.e. procurement strategy, purchasing portfolio model, information flow management and cost analysis. The background for the development of category planning process was derived from retail industry, to where the category planning is more researched. The empirical study was executed with mixed method approach: quantitative data of the categories was analyzed and qualitative data was gathered through semi-structured interview and discussions within the case company. As a result, the category planning process was critically analyzed and development proposals addressed for improving the process description. Additionally a tool was developed based on the empirical study to support the category planning process of the case company.

Business-Oriented IT Tool Development For Service Delivery Process

The target of this thesis is to evaluate a bid, project and resource management IT tool for service delivery process via proof-of-concept (POC) project to assess, if the tested software is an appropriate tool for the Case Company’s business requirements. Literature suggests that IT projects implementation is still a grey area in scientific research. Also, IT projects have a notably high rate of failure, one significant reason for this being insufficient planning. To tackle this risk, the Case Company decided to perform a POC project, which involved a hands-on testing period of the assessed system. End users from the business side feel that current, highly tailored project management tool is inflexible, difficult to use, and sets unnecessary limitations for the business. Semi-structured interviews and a survey form are used to collect information about current business practices and business requirements related to the IT tool. For the POC project, a project group involving members from each of the Case Company’s four business divisions was established to perform the hands-on testing. Based on data acquired during the interviews and the hands-on testing period, a target state was defined and a gap analysis was carried out by comparing the features provided by the current tool and the tested tool to the target state, which are, together with the current state description, the most important result of the thesis.

Slöjd som process och produkt : Talking Tools som dokumentations- och utvärderingsverktyg

Syftet med denna studie är att granska hur användningen av smarttelefoner kan stöda elevens reflektion av sin egen slöjdprocess och samtidigt se hur eleven dokumenterar sin slöjdprocess med hjälp av Talking Tools (TT). Fokus i denna studie ligger på dokumentation av elevens slöjdprocess, men jag behandlar även presentation av slöjdprodukter och olika möjligheter till och sätt på hur eleverna använder TT på en smarttelefon i slöjdundervisningen. En förändring i hur informations- och kommunikationsteknik (IKT) används sker och kommer även att ske i fortsättningen i grundskolan. Då en ny läroplan för den grundläggande utbildningen tas i bruk år 2016 kommer IKT att ha en avsevärt större roll. Denna förändring lägger press på lärare och på skolan överlag för att skapa ändamålsenliga metoder i användningen av IKT. Studien baserar sig på intervjuer med elever som använt TT under ett arbetsområde i slöjden. Elva elever presenterade först sina slöjdprodukter för forskaren varefter eleverna intervjuades. Eleverna hade tillgång till sina slöjdbloggar gjorda i TT under intervjutillfällena. Intervjuerna filmades och lades ihop med bloggarna för att förenkla analysen av materialet. I den här undersökningen framkom att dokumentationen av slöjdprocessen bidrog till en reflektion av när bilder och texter från bloggarna användes under presentationerna. Då kraven på dokumenteringen av arbetet i skolan blir högre i och med läroplanen 2016 tror jag att Talking Tools kan vara ett hjälpmedel för elever och lärare i förverkligandet av bland annat användningen av IKT i arbetet i skolan. Detta förutsätter att eleverna ges tid för användningen samt att tekniken fungerar.

The demand-supply balancing process in supply chain management - case mining & metals industry equipment

The aim of this thesis is to search how to match the demand and supply effectively in industrial and project-oriented business environment. The demand-supply balancing process is searched through three different phases: the demand planning and forecasting, synchronization of demand and supply and measurement of the results. The thesis contains a single case study that has been implemented in a company called Outotec. In the case study the demand is planned and forecasted with qualitative (judgmental) forecasting method. The quantitative forecasting methods are searched further to support the demand forecast and long term planning. The sales and operations planning process is used in the synchronization of the demand and supply. The demand forecast is applied in the management of a supply chain of critical unit of elemental analyzer. Different meters on operational and strategic level are proposed for the measurement of performance.

Maximizing of water recovery in nanofiltration of mine process waters by using antiscalants

Reverse osmosis and nanofiltration are among the most effective and widely used desalination and water softening technologies. They can also be used to treat mining wastewaters and are capable of producing water of extremely high purity, regardless of the high concentrations of toxic heavy metals and extreme pH and salinity. However, challenges with recovering the salts and metals from mining wastewaters in exploitable form, as well as problems with scaling still limit the process efficiency and the ratio of purified water recoverable from process waters. To address the problem of membrane scaling caused by calcium sulfate, batch filtration experiments with the Desal-5 DL nanofiltration membrane, three commercial antiscalants and actual mine process water from a copper mine were performed. The aim of these experiments was to find process conditions where maximum water recovery would be achieved before significant scaling or irreversible membrane fouling would occur and to further improve water recovery by addition of antiscalants. Water recovery of 70 % was reached with the experimental setups by optimizing process conditions. PC-504T antiscaling agent was determined to be the most effective of the three antiscalants used and the addition of 5 ppm of PC-504T allowed the water recovery to be further increased from 70 % to 85 % before major scaling was observed. In these conditions 92 % calcium rejection was achieved.

Balancing the quotation process by LEAN methods

This thesis studies the possibility to use lean tools and methods in a quotation process which is carried out in an office environment. The aim of the study was to find out and test the relevant lean tools and methods which can help to balance and standardize the quotation process, and reduce the variance in quotation lead times and in quality. Seminal works, researches and guide books related to the topic were used as the basis for the theory development. Based on the literature review and the case company’s own lean experience, the applicable lean tools and methods were selected to be tested by a sales support team. Leveling production, by product categorization and value stream mapping, was a key method to be used to balance the quotation process. 5S method was started concurrently for standardizing the work. Results of the testing period showed that lean tools and methods are applicable in office process and selected tools and methods helped to balance and standardize the quotation process. Case company’s sales support team decided to implement new lean based quotation process model.

Development of project cash flow forecasting process

Process management refers to improving the key functions of a company. The main functions of the case company - project management, procurement, finance, and human resource - use their own separate systems. The case company is in the process of changing its software. Different functions will use the same system in the future. This software change causes changes in some of the company’s processes. Project cash flow forecasting process is one of the changing processes. Cash flow forecasting ensures the sufficiency of money and prepares for possible changes in the future. This will help to ensure the company’s viability. The purpose of the research is to describe a new project cash flow forecasting process. In addition, the aim is to analyze the impacts of the process change, with regard to the project control department’s workload and resources through the process measurement, and how the impacts take the department’s future operations into account. The research is based on process management. Processes, their descriptions, and the way the process management uses the information, are discussed in the theory part of this research. The theory part is based on literature and articles. Project cash flow and forecasting-related benefits are also discussed. After this, the project cash flow forecasting as-is and to-be processes are described by utilizing information, obtained from the theoretical part, as well as the know-how of the project control department’s personnel. Written descriptions and cross-functional flowcharts are used for descriptions. Process measurement is based on interviews with the personnel – mainly cost controllers and department managers. The process change and the integration of two processes will allow work time for other things, for example, analysis of costs. In addition to the quality of the cash flow information will improve compared to the as-is process. Analyzing the department’s other main processes, department’s roles, and their responsibilities should be checked and redesigned. This way, there will be an opportunity to achieve the best possible efficiency and cost savings.

Improving reporting and internal control with process thinking - case study in a multinational corporation

The aim of this Master’s Thesis is to find applicable methods from process management literature for improving reporting and internal control in a multinational corporation. The method of analysis is qualitative and the research is conducted as a case study. Empirical data collection is carried out through interviews and participating observation. The theoretical framework is built around reporting and guidance between parent company and subsidiary, searching for means to improve them from process thinking and applicable frameworks. In the thesis, the process of intercompany reporting in the case company is modelled, and its weak points, risks, and development targets are identified. The framework of critical success factors in process improvement is utilized in assessing the development targets. Also internal control is analyzed with the tools of process thinking. As a result of this thesis, suggestions for actions improving the reporting process and internal control are made to the case company, the most essential of which are ensuring top management’s awareness and commitment to improvement, creating guidelines and tools for internal control and creating and implementing improved intercompany reporting process.

Innovation process development and business process integration - a multiple case study

The main objective of this study was to find out the bases for innovation model formulation in an existing organization based on cases. Innovation processes can be analyzed based on their needs and based on their emphasis on the business model development or R&D. The research was conducted in energy sector within one company by utilizing its projects as cases for the study. It is typical for the field of business that development is slow, although the case company has put emphasis on its innovation efforts. Analysis was done by identifying the cases’ needs and comparing them. The results were that because of the variances in the needs of the cases, the applicability of innovation process models varies. It was discovered that by dividing the process into two phases, a uniform model could be composed. This model would fulfill the needs of the cases and potential future projects as well.

Creating a Branding Process Model for Living Area Brands - Developing and managing a new living area brand

The objective of this thesis is to understand how to create and develop a successful place brand and how to manage it systematically. The thesis thoroughly explains the phenomenon of place brands and place branding and presents different sub-categories of place branding. The theoretical part of the thesis provides a wide overview on the prevailing literature of place branding, place brand development and place brand management, which form the basis of the thesis’ theoretical framework. The theoretical evidence is gathered from a case living area. The living area is developed by one construction company, which has a significant role in the construction industry in Finland. The empirical evidence is gathered through semi-structured in-depth interviews by interviewing the new living area’s carefully selected stakeholder groups. Afterwards the empirical data is analyzed and reflected to the theoretical findings. After examining the case living area, the thesis will present a new living area branding process model based on prevailing theories and empirical findings.

Roll-to-roll atomic layer deposition process for flexible electronics applications

Atomic Layer Deposition (ALD) is the technology of choice where very thin and highquality films are required. Its advantage is its ability to deposit dense and pinhole-free coatings in a controllable manner. It has already shown promising results in a range of applications, e.g. diffusion barrier coatings for OLED displays, surface passivation layers for solar panels. Spatial Atomic Layer Deposition (SALD) is a concept that allows a dramatic increase in ALD throughput. During the SALD process, the substrate moves between spatially separated zones filled with the respective precursor gases and reagents in such a manner that the exposure sequence replicates the conventional ALD cycle. The present work describes the development of a high-throughput ALD process. Preliminary process studies were made using an SALD reactor designed especially for this purpose. The basic properties of the ALD process were demonstrated using the wellstudied Al2O3 trimethyl aluminium (TMA)+H2O process. It was shown that the SALD reactor is able to deposit uniform films in true ALD mode. The ALD nature of the process was proven by demonstrating self-limiting behaviour and linear film growth. The process behaviour and properties of synthesized films were in good agreement with previous ALD studies. Issues related to anomalous deposition at low temperatures were addressed as well. The quality of the coatings was demonstrated by applying 20 nm of the Al2O3 on to polymer substrate and measuring its moisture barrier properties. The results of tests confirmed the superior properties of the coatings and their suitability for flexible electronics encapsulation. Successful results led to the development of a pilot scale roll-to-roll coating system. It was demonstrated that the system is able to deposit superior quality films with a water transmission rate of 5x10-6 g/m2day at a web speed of 0.25 m/min. That is equivalent to a production rate of 180 m2/day and can be potentially increased by using wider webs. State-of-art film quality, high production rates and repeatable results make SALD the technology of choice for manufacturing ultra-high barrier coatings for flexible electronics.

A morphometric study of the lumbar spinous process in the Chinese population

Our goal was to analyze the anatomical parameters of the lumbar spine spinous process for an interspinous stabilization device designed for the Chinese population and to offer an anatomical basis for its clinical application. The posterior lumbar spines (T12-S1) of 52 adult cadavers were used for measuring the following: distance between two adjacent spinous processes (DB), distance across two adjacent spinous processes (DA), thickness of the central spinous processes (TC), thickness of the superior margin of the spinous processes (TS), thickness of the inferior margin of the spinous processes (TI), and height of the spinous processes (H). Variance and correlation analyses were conducted for these data, and the data met the normal distribution and homogeneity of variance. DB decreased gradually from L1-2 to L5-S1. DA increased from T12-L1 to L2-3 and then decreased from L2-3 to L4-5. The largest H in males was noted at L3 (25.45±5.96 mm), whereas for females the largest H was noted at L4 (18.71±4.50 mm). Usually, TS of the adjacent spinous process was lower than TI. Based on the anatomical parameters of the lumbar spinous processes obtained in this study, an “H”-shaped coronal plane (posterior view) was proposed as an interspinous stabilization device for the Chinese population. This study reports morphometric data of the lumbar spinous processes in the Chinese population, which provides an anatomical basis for future clinical applications.