Efficiency of safety measures applied to a manual knapsack sprayer for paraquat application to Maize (Zea mays L.)

The objectives of the present study were to evaluate the safety of mixer/loaders and applicators of paraquat to maize crop by knapsack sprayers and to determine the efficacy of safety measures applied to the sprayers. Potential dermal exposure (PDE) was evaluated in 22 worker body parts. The Cu2+ cation of a copper-based fungicide was used as tracer in the spray solution. Sanitary pads and cotton gloves were used to collect the pesticide solution on the sampled body parts. It was observed that paraquat application in front of the applicator's body (0.5 and 1.0 m lance) is unsafe because PDE was 1,979.8 ml/day (for 0.5 m lance) and 1,290.4 ml/day (for 1.0 m lance) and needs 50-80% and 37-69% control of PDE respectively. Control can be achieved by the use of protective garment on the legs and feet only, which received 92-93% of the PDE. Switching the spray nozzle to the back of the operator reduced the PDE by 98% and was sufficient to make working conditions safe, while maintaining the efficiency of application and making the work lighter and more comfortable. Mixer/loaders received 86% of the PDE to the hands and the work condition was safe (MOS > 1), however impermeable gloves could be used as a further safety measure.

Identificação e quantificação de resinas, cargas e pigmentos em tintas látex branca

Resins, pigments and fillers constituents in white latex paint were identified and quantified after previous treatment under both low temperature and low pressure in order to get toilet powder from emulsion samples. TG/DTA allowed, under determined conditions, to distinguish the kind of resins, fillers and pigments in commercial paints. X-ray diffractometry was used to confirm the presence of pigment in the final residue from the thermal decomposition.

Influence of thermal treatments in the corrosion behaviour of HVOF Cr 3C2-NiCr coatings

Thermal spray coatings as Cr3C2-NiCr obtained by high velocity oxy-fuel spraying (HVOF) are mainly applied due to their behaviour against aggressive erosive-abrasive and corrosive atmospheres and their thermal stability at high temperatures [1]. In order to increase the corrosion protection that it offers to the substrate trying to close the interconnected pores, it is possible to apply a thermal treatment with the gun during the spraying of the coating. This treatment could be applied in different ways. One of these ways consists of spraying only a few layers of coating followed by thermal treatment and finally the spray of the rest of layers. This thermal treatment on spraying is studied related to the corrosion properties of the system. The study comprises the electrochemical characterisation of the system by open circuit potential (OC), polarisation resistance (Rp), cyclic voltammetry (CV) and impedance spectroscopy measurements (EIS). Optical and scanning electron microscopy characterisation (OM and SEM) of the top and cross-section of the system has been used in order to justify the electrochemical results.

Effect of growth regulators in citral content in lemongrass in different seasons (in Portuguese)

The purpose of the present research was to evaluate the effect of plant growth regulators in yield citral content in lemongrass (Cymbopogon citratus (D.C.) Stapf), in different seasons. The field experiment was conducted on Sao Manuel Experimental Farm, Agronomical Science College, Paulista Estatal University, Botucatu, Brazil, which soil was classified in alic yellon red latosol (Haplorthox). Plants were randommly assigned blocks to treatments with three repetitions. The experimental groups consisted of GA3 (50 and 100 mg.l-1);Ethrel (100 and 200 mgl-1); CCC (500 and 1000 mg.l-1); Alar 85 (1000 and 2000 mg.l-1); Accel (20 and 40 mg.l-1) and control group. Five applications of plant growth regulators were realized every other three months. After 40 days of each foliar spray, the plants were cut and determined the citral yield. The essential oils were extracted from leaf tissue by hydrodistillation in a Clevenger apparatus. Samples of 250g of leaf and put in Clevenger apparatus with deionized water for 3h to determine the yield of essential oil. The citral content was analyzed by GC. In the present study the concentrations of plant growth regulators used did not increase citral content.

Características da pulverização produzida por pontas Yamaho da série 'D'

This study evaluated the characteristics of spray produced by Yamaho nozzle tip'D'series. The droplet size of nozzle tips D3, D4, D5, D6 and D8 were evaluated at 703, 1.050, 1.406, 1.758, 2.110, 2.461 e 2.813 kPa pressures (100, 200, 250; 350, e 400 psi) by means of laser equipment, as well as the flow rate of nozzle tip at the pressures of 702, 1.125, 1.406, 1.828, 2.110, 2.532 e 2.813 kPa (100, 160, 200, 260,300; 360 e 400 psi) which were compared with values indicated by manufacturer. The droplet produced at all pressures presented a very fine spray, which in agriculture may promote losses by evaporation and drift. For all nozzle tips, except D8 in pressures 1.828, 2.532 e 2.813 kPa, the difference between the observed flow rate indicated by the manufacturer was higher than 5%. The paper demonstrates that the nozzle tip tested, in spite of not having uniform flow rate, may promote the contamination of spray operator and environment due to the droplet spectrum produced.

Phosphorus foliar fertilization in guava trees

Currently there is very little information on the response of fruiting perennial plants to applied P. This is especially true for tropical production areas where soils have a high capacity of P fixation, and are poor in native phosphorus. An alternative to soil P fertilization, which is inefficient in fixing soils, is to apply phosphorus as a foliar spray. P is quickly absorbed by leaves, and is redistributed quite well through the plants because its phloem mobility, and foliar application may be a viable practice. The purpose of this present work, is to determine the effectiveness of foliar P application on the nutritional status and yield of guava. The experiment was done in a Typic Hapludox, for three consecutive agricultural years, in an adult orchard of 'Paluma' guava. Five treatments were tested: four rates leaf applications of P (0-0.5-1.0 and 2.0% of P2O5) and a control where P was applied to soil (200 g of P2O5/plant). Through the results it was verified that the foliar application of P altered the concentration of the nutrient in the soil (13 to 48 mg dm-3 P-resin), and in the guava leaves (1.2 to 1.8 g of P kg-1), but did not affect the production of fruits. In conclusion, in field conditions, it is viable to combine the phosphorus foliar fertilization with disease control, without increasing the operations and, consequently, the production cost.

Dental implants: Surface modification of cp-Ti using plasma spraying and the deposition of hydroxyapatite

The commercial pure titanium (cp-Ti) is currently being used with great success in dental implants. In this work we investigate how the cp-Ti implants can be improved by modifying the metal surface morphology, on which a synthetic material with properties similar to that of the inorganic part of the bone, is deposited to facilitate the bone/implant bonding. This synthetic material is the hydroxyapatite, HA, a calcium-phosphate ceramic. The surface modification consists in the application of a titanium oxide (TiO2) layer, using the thermal aspersion - plasma spray technique, with posterior deposition of HA, using the biomimetic method. The X-ray diffraction (XRD), Scanning Electron Microscopy (SEM) with Energy Dispersive X-ray (EDX) and Diffuse Reflectance Infrared Fourier Transform (DRIFT) techniques have been used for characterizing phases, microstructures and morphologies of the coatings. The TiO2 deposit shows a mixture of anatase, rutilo and TiO2-x phases, and a porous and laminar morphology, which facilitate the HA deposition. After the thermal treatment, the previously amorphous structured HA coating, shows a porous homogeneous morphology with particle size of about 2-2.5 μm, with crystallinity and composition similar to that of the biological HA.

Estudo das características morfológicas dos pites nos materiais resistentes à corrosão

This paper has as a purpose a new alternative technique development to characterize pitting corrosion evolution, aiming classification, size and determination of morphological parameters which rule pits increase. In this case, the method will be applied to the 304 ABNT stainless steel, thermally treated and exposed to different times in salt spray. Different 304 steel conditions, rolled and thermally treated have exhibited similar geometry, predominantly conic, near-conic and irregular pits. On rolled steel, pits width increases faster than height; however, on thermally treated steel, pits are found to increase in height.

Evaluation of systems for timing of fungicide sprays for control of postbloom fruit drop of citrus in Brazil

Postbloom fruit drop (PFD) of citrus, caused by Colletotrichum acutatum, infects petals of citrus flowers and produces orange-brown lesions that induce the abscission of young fruitlets and the retention of calyces. Proper timing of fungicide applications is essential for good disease control. Different systems for timing of fungicide applications for control of PFD in a major citrus-growing region in southern São Paulo state in Brazil were evaluated from 1999 to 2002. The following programs were compared to an unsprayed control using counts of diseased flowers, persistent calyces, or fruit: (i) a phenology-based program currently recommended in Brazil with one application at early and another at peak bloom; (ii) the Florida PFD model; (iii) the postbloom fruit drop-fungicide application decision system (PFD-FAD), a new computer-assisted decision method; and (iv) grower's choice. In 1999, no disease developed, sprays applied with the phenology-based program had no effect, and the Florida PFD model saved two sprays compared with the phenology-based program. In 2000, PFD was moderate and the phenology-based and growers' choice treatments had a significantly lower number of persistent calyces and higher fruit numbers than the control, but no differences were found between those treatments and the PFD model. In 2001, PFD was severe with considerable yield loss. The PFD model, the phenology-based program, and the grower's choice reduced flower blight and the number of persistent calyces, and improved fruit yields with two to three applications, but the PFD-FAD achieved comparable yields with only one spray. In 2002, the disease was mild, with no yield loss, and the Florida PFD model and the PFD-FAD saved one spray compared with the other systems. The PFD model and the PFD-FAD were equally effective for timing fungicide applications to control PFD in Brazil. Scouting of trees is simpler with PFD-FAD; therefore, this system is recommended and should eliminate unnecessary sprays and reduce costs for growers.

Occupational exposure to paint solvents and particulate material in car repair shops

Aims: We evaluated solvents and total particulates exposures in auto body repair shops together with a search of painter's related complaints. Methods: 26 painters exposures were evaluated by pumped personal sampling; solvents were retained in charcoal sorbent tubes and the particulates in PVC filters. Painter's personal habits and their work characteristics were obtained through a questionnaire, applied in a private interview. For the symptoms the Q16 questionnaire was used, added of questions about complaints during the painting. Results: High exposures were detected during spray painting. For solvents, the TLV-STEL adjusted for the mixtures was surpassed in six evaluations. However, as repaint is a short-term operation, it makes the average concentrations weighed for the work shift lower than the TLV-TWA adjusted for the mixtures. Total particulate concentrations had surpassed the TLV-TWA in four of the evaluations. Symptoms frequency in the Q16 questionnaire was higher for painters than for the controls (Mann-Whitney test U=193; p=0.008), and they showed positive correlations with the age (Spearman r=0.354, t=1.85, p=0.076), the number of years in the profession (Spearman r=0.433, t=2.35, p=0.027) and the alcoholic beverage consumption (Spearman r=0.457, t=2.516, p=0.019). Conclusions: The painting work done at car repair shops can result in high solvent and particulate exposures, although they are short-term operations. Their acute and chronic effects for the painters do not have been clearly evidenced in the present study, continuing deserving multidisciplinary attention.

Effect of daminozide, paclobutrazol and chlormequat on development and quality of potted 'persian carpet' zinnia

In Brazil zinnias have good prospect for the flowering potted plant market, once consumers demand for new forms of products is stimulated by novelty. 'Persian Carpet' is a highly ornamental plant, with fast growth, minimal labor requirements and low cost seeds. The present study evaluated the effect of growth regulators on development and quality of 'Persian Carpet' grown as a potted plant. Growth regulators are commonly used to control growth and produce short and compact plants. Paclobutrazol (0.5, 0.75 and 1.0 mg a.i./pot) and chlormequat (1.0, 2.0 and 3.0 g. L-1) were applied as a single drench, and daminozide (2.5, 3.75 and 5.0 g. L-1) as a single foliar spray to runoff. Regulators were applied at apical flower bud stage. Daminozide (5.0 g. L-1), paclobutrazol (0.5, 0.75 and 1.0 mg a.i./pot) and chlormequat (1.0 g. L-1) significantly reduced plant height and side branches length compared to the control. Plant height showed a negative linear response to the increasing concentration of daminozide or paclobutrazol. Paclobutrazol (1.0 mg a.i./pot) and chlormequat (1.0 g. L-1) increased foliage and flowers harvest index. Plant spread diameter and canopy shape were improved with paclobutrazol (0.75 mg a.i./pot). Chlormequat (2.0 and 3.0 g. L-1) caused phytotoxicity symptoms, turning plants unsuitable for commercialization. Studied regulators concentrations did not affect flower diameter and production cycle. Although regulators controlled height and side branches growth significantly, plants were not short and compact enough to attend market quality.

Reguladores vegetais na produção de biomassa e teor de óleos essenciais em Cymbopogon citratus (DC.) Stapf, em diferentes épocas do ano

The purpose of the present research was to evaluate the effect of plant growth regulators in biomass production and essential oil yield content in lemongrass (Cymbopogon citratus (DC.) Stapf), in different seasons. The experiment was conducted on São Manuel Experimental Farm, Faculdade de Ciências Agronômicas, UNESP - Botucatu. Which plants were randomly assigned into blocks to treatments with three repetitions. The treatments consisted of GA3 (50 and 100 mg L-1); Ethrel (100 and 200 mg L-1); CCC (500 and 1000 mg L-1); Alar 85 (1000 and 2000 mg L-1); Accel (20 and 40 mg 0L-1) and control. Four applications of plant growth regulators were realized every three months. After 40 days of each foliar spray, the plants were cut to determine the fresh weight and essential oil yield. The application of plant growth regulators did not increase the biomass production, showing difference among collect periods when the major production was detected at the fourth collect (summer). The greatest essential oil yield was found at the second collect (winter). In the present study, the used concentrations of plant growth regulators did not increase biomass neither essential oil yield.

An overview of the microstructures present in high-speed steel - Carbides crystallography

The aim of the work was to prepare an overview about the microstructures present in high-speed steel, focused on the crystallography of the carbides. High-speed steels are currently obtained by casting, powder metallurgy and more recently spray forming. High-speed steels have a high hardness resulting from a microstructure, which consists of a steel matrix (martensite and ferrite), in which embedded carbides of different crystal structure, chemical composition, morphology and size, exist. These carbides are commonly named MxC, where M represents one or more metallic atoms. These carbides can be identified by X-ray diffraction considering M as a unique metallic atom. In this work, it is discussed, in basis of the first principles of physics crystallography, the validation of this identification when it is considered that other atoms in the structure are substitutional. Further, it is discussed some requirements for data acquisition that allows the Rietveld refinement to be applied on carbide crystallography and phase amount determination.

Influência da granulometria de grânulos de amido sobre a densidade aparente de extratos atomizados

Starches and modified starch derivations are used as carriers in the spray drying processing where apparent density is an important characteristic and should be controlled in dehydrated products for pharmaceutical use. In Brazil, the commercial starches are made from corn and cassava, but there are others with potential for extraction. The canna and taro starches were selected because they represent the extremes of granule size and thus allow the effect of this size on the apparent density of spray dried products to be tested. For comparison, commercial cassava and corn starches which are used in spray-drying and have granules of intermediate size, were also tested. The spray-drying process was carried out with a LabPlant SD 04 Spray Dryer, operating at a pressure of 6 lb/in2, air of 7,6 mL/minute, and 1 cm atomizing nozzle. The air inlet temperature was set at 200°C this model does not allow regulating outlet temperature. The spray-dryer products had boldo leaf extract as base, using the four starches as carrier. The dry product was evaluated for humidity, water activity (Aw), granulometry and apparent density. The results showed that the size of the particles, which was a consequence of the size of the starch granules, influenced the apparent density of the spray dried products, which as higher (694, 27 g/mL) for the canna starch and lower (456, 13 g/mL) for taro starch. Corn and cassava starches showed very close and intermediate values, 521,51 and 58,48 g/mL, which also represent the standard range of starch granule size.

Efficacy of topical permethrin as repellent against aedes aegypti's bites

Mosquitoes are the most important vectors of infectious diseases and their bites are related to several adverse skin reactions. Permethrin impregnated clothes are an efficient strategy against arthropods' bites; however, its topical efficacy as a repellent has not been well established. We studied the response to permethrin lotion 5 percent and N,N-Diethyl-meta-toluamide (DEET) spray 50 percent applied to the unprotected forearms of 10 volunteers. Each arm was exposed to 20 female mosquitoes of Aedes aegypti. We performed 71 bilateral comparative measurements evaluating the timing for the first bites. The average times for the arm without the product, with permethrin 5 percent, and with DEET 50 percent were: 7.9 seconds, 336.2 seconds and 7512.1 seconds. The results showed a significant difference between repellency times between either product and unprotected controls. In addition, there was a significant difference in time to first bite between permethrin and DEET treated arms (p<0.01). Permethrin affords some repellent activity against Aedes aegypti bites in this experimental setting. However, permethrin's profile of repellency was significantly inferior to that of DEET. © 2008 Dermatology Online Journal.