Thermodynamic analysis and comparison of downdraft gasifiers integrated with gas turbine, spark and compression ignition engines for distributed power generation

The objective of the present article is to assess and compare the performance of electricity generation systems integrated with downdraft biomass gasifiers for distributed power generation. A model for estimating the electric power generation of internal combustion engines and gas turbines powered by syngas was developed. First, the model determines the syngas composition and the lower heating value; and second, these data are used to evaluate power generation in Otto, Diesel, and Brayton cycles. Four synthesis gas compositions were tested for gasification with: air; pure oxygen; 60% oxygen with 40% steam; and 60% air with 40% steam. The results show a maximum power ratio of 0.567 kWh/Nm(3) for the gas turbine system, 0.647 kWh/Nm(3) for the compression ignition engine, and 0.775 kWh/Nm(3) for the spark-ignition engine while running on synthesis gas which was produced using pure oxygen as gasification agent. When these three systems run on synthesis gas produced using atmospheric air as gasification agent, the maximum power ratios were 0.274 kWh/Nm(3) for the gas turbine system, 0.302 kWh/Nm(3) for CIE, and 0.282 kWh/Nm(3) for SIE. The relationship between power output and synthesis gas flow variations is presented as is the dependence of efficiency on compression ratios. Since the maximum attainable power ratio of CIE is higher than that of SIE for gasification with air, more research should be performed on utilization of synthesis gas in CIE. (C) 2014 Elsevier Ltd. All rights reserved.

Performance evaluation of multi-stage filtration with use of granular activated carbon and synthetic non-woven fabrics

The multi stage filtration (MSF) is an alternative that permits to enlarge the spectrum of application of the slow sand filtration as for the effluent quality and run duration. In this research the use of MSF technology associated to a granular activated carbon (GAC) column as polishing mechanism of the final effluent was evaluated; in the slow sand filters GAC was used as an intermediate layer and non-woven synthetic fabrics were utilized as a first layer of the filter media. Five different tests were conducted, where the systems subjected to the treatment were: water from the Ipe Lake (Ilha Solteira, Sao Paulo, Brazil); water from the lake with water from a recreational fish pond; water from the lake with a phytoplankton and cyanobacteria overload simulation, with and without the use of the pre-filters as a stage of the treatment. The synthetic fabrics and GAC use resulted in the best turbidity removal and an efficient apparent and true color removal; in spite that the polishing columns reported similar results for those parameters. The utilization of GAC as an intermediate layer contributed to a better organic matter removal and the fabrics improved chlorophyll-a removal. The pre-filtration columns made an efficient algae and cyanobacteria removal, a function that was completed by the filters and reached >98% efficiency. The synthetic non-woven fabrics and GAC inclusion in MSF operation improved performance of this technology with ease of application and operation.

Evaluation of fecal microorganisms of children with cleft palate before and after palatoplasty

This study isolated and quantified intestinal bacteria of children with cleft palate before and after palatoplasty. A prospective study was conducted from May 2007 to September 2008 on 18 children with cleft palate, aged one to four years, of both genders, attending a tertiary cleft center in Brazil for palatoplasty, to analyze the effect of surgical palate repair on the concentration of anaerobes Bacteroides sp, Bifidobacterium sp and microaerophiles Lactobacillus sp in feces of infants with cleft palate before and 24 hours after treatment with cefazolin for palatoplasty. There was significant reduction of Lactobacillus sp (p < 0.002), Bacteroides sp (p < 0.001) and Bifidobacterium sp (p = 0.021) after palatoplasty, revealing that surgery and utilization of cefazolin significantly influenced the fecal microbiota comparing collections before and after surgery. However, due to study limitations, it was not possible to conclude that other isolated factors, such as surgical stress, anesthetics and other medications used in palatoplasty might have a significant influence on the microbiota. Considering the important participation of the intestinal microbiota on both local and systemic metabolic and immunological activities of the host, professionals should be attentive to the possible influence of these changes in patients submitted to cleft repair.

Adhesion of substrate-adherent combinations for early composite repairs: Effect of intermediate adhesive resin application

This study evaluated the effect of intermediate adhesive resin application (IAR) on tensile bond strength (TBS) for early composite repairs in situations where substrate and repair composite bonded together were once of the same kind with the substrate (similar) and once other than the substrate material (dissimilar). Specimens from three types of composites (TPH Spectrum (TPH), Charisma (CHA) and Filtek Z250 (Z250)) were fabricated. The specimens in each composite group (n=72) were randomly divided into six subgroups (n=12). In each composite group, the similar and two dissimilar composites were bonded onto the substrates once using an IAR (Adper Single Bond Plus) and once without. After water storage for I week at 37 degrees C, substrate-adherent combinations were submitted to tensile test. Data were analyzed with three-way ANOVA and Tukey's tests (alpha=0.05). The substrate-adherent combination (p=0.0001), adherent (repair) composite (p=0.0001), and application of IAR (p=0.0001) significantly affected the results. Utilization of IAR improved the repair bond strength for all composite combinations. (C) 2013 Elsevier Ltd. All rights reserved.

A New and Simple Visual Technique Based on Indigo Dye for Determination of Ozone in Ambient Air

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Effects of potassium and sodium supply on drought-adaptive mechanisms in Eucalyptus grandis plantations

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Thermal Characteristics of Lignin Residue from Industrial Processes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Prediction of the combustion process in fluidized bed based on physical-chemical properties of biomass particles and their hydrodynamic behaviors

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Substrates and controlled-release fertilizations on the quality of eucalyptus cuttings

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

An innovative material based on natural rubber and leather tannery waste to be applied as antistatic flooring

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

THE PARASITOID, Cotesia flavipes (CAMERON) (HYMENOPTERA: BRACONIDAE), INFLUENCES FOOD CONSUMPTION AND UTILIZATION BY LARVAL Diatraea saccharalis (F.) (LEPIDOPTERA: CRAMBIDAE)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Comparison of polymers and ceramics in new and discarded electrical insulators: reuse and recycling possibilities

The expansion and maintenance of electricity distribution networks generates large amounts of waste, much of it in the form of discarded insulators that are not reused or recycled. This paper describes the results of tests on used and new ceramic and polymeric insulators to verify if their exposure to weathering justifies their replacement. In new and used ceramic insulators, properties such as contact angle, relative density, porosimetry, dilatometry and X-ray diffraction patterns showed no differences or the differences that were found could not be related to their use. The discarded ceramic material showed high thermal stability, an interesting characteristic for application as chamotte. It can also be reused to replace gravel used in substations. In polymeric insulators, thermogravimetry, differential scanning calorimetry and relative density test results suggest degradation of used material compared to new. This would justify their replacement and discard as waste, but they show little recycling potential.

Response of pullets to digestible lysine intake

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of dietary energy concentration on performance parameters and egg quality of white leghorn laying hens

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo comparativo entre MDF e MDP utilizados na indústria moveleira

Increasingly, the furniture market is competitive. The construction industry presents itself in growth, mainly due to the lines of existing incentives and tax credits established by the government, assisting the impulse to purchase real estate, building materials and furniture. Factors that promote and strengthen the sector's growth. With high demand from the furniture market, demand for higher quality and increasing technological advances, research is often undertaken in search of solutions for process improvement and product features, focusing on the production of materials less harmful to the environment, provision of raw press to lower cost, improve the production process and product development of cost-effective. This research focuses on the comparative study between two materials widely used in furniture manufacturing. MDF (Medium Density Fiberboard) and MDP (Medium Density Particleboard). The subject provides the focus in furniture production, presenting and comparing data collected from three companies producing panels between physical and mechanical characteristics of the materials, also presenting some of the main factors of influence on the quality of the panels, their features and applications on mobile. The study shows the high potential of using the MDP (Medium Density Particleboard) in furniture designs, as well as MDF (Medium Density Particleboard), favoring the final terms of the project , resulting in better utilization of each material , avoiding waste and increase unnecessary cost . Currently, several projects are developed in MDP and MDF furniture, where there is no relevance to their characteristics regarding their limitations. Many of these furnishings are designed without a specific study of the best use and positioning of each material, with better utilization , favoring collateral design , especially furniture designed exclusively for each environment . The lack of technical ...