Performance of Nongrouted Thin Bonded PCC Overlays, Construction Report, HR-291, 1986

The Iowa road system has approximately 13,000 miles of Portland Cement Concrete Pavements, many of which are reaching the stage where major rehabilitation is required. Age, greater than anticipated traffic, heavier loads and deterioration related to coarse aggregate in the original pavement are some of the reasons that these pavements have reached this level of distress. One method utilized to rehabilitate distressed or underdesigned PCC pavements is the thin bonded Portland Cement Concrete overlay. Since the introduction of thin bonded overlays on highway pavements in 1973, the concrete paving industry has made progress in reducing the construction costs of this rehabilitation technique. With the advent of the shotblast machine, surface preparation costs have decreased from over $4.00 per square yard to most recently $1.42 per square yard. Other construction costs, including placement, grouting and sawing, have also declined. With each project, knowledge and efficiency have improved.

Assessment of growth and yield performance of rubber tree clones of the IAC 500 series

The objective of this work was to evaluate the performance of 15 clones of the IAC 500 series of Hevea brasiliensis, developed at Instituto Agronômico (IAC), over a 12-year period, in the northwest region of São Paulo State, Brazil. The 15 new clones evaluated are primary clones obtained from selected ortets within half-sib progenies. The clone RRIM 600, of Malaysian origin, was used as the control. Dry rubber yield performance over a four-year period, mean girth at the tenth year, girth increment before and during tapping, thermal properties of the natural rubber produced and other characters of the laticiferous system were evaluated. Forty percent of the clones were superior in comparison to the control for yield. Clone IAC 500 recorded the highest yield (66.81 g per tree per tapping) over four years of tapping, followed by IAC 502 (62.37 g per tree per tapping), whereas the control recorded 48.71 g per tree per tapping. All selected clones were vigorous in growth. The natural rubber from this IAC clones showed thermal stability up to 300ºC. No differences were observed in the thermal behavior of rubber among the IAC series and the RRIM 600 clones. The clones IAC 500, IAC 501, IAC 502, IAC 503 and IAC 506 are the more promising for small-scale plantations, due to growth and yield potential.

A comparison of the imaging characteristics of the new Kodak Hyper Speed G film with the current T-MAT G/RA film and the CR 9000 system.

Three standard radiation qualities (RQA 3, RQA 5 and RQA 9) and two screens, Kodak Lanex Regular and Insight Skeletal, were used to compare the imaging performance and dose requirements of the new Kodak Hyper Speed G and the current Kodak T-MAT G/RA medical x-ray films. The noise equivalent quanta (NEQ) and detective quantum efficiencies (DQE) of the four screen-film combinations were measured at three gross optical densities and compared with the characteristics for the Kodak CR 9000 system with GP (general purpose) and HR (high resolution) phosphor plates. The new Hyper Speed G film has double the intrinsic sensitivity of the T-MAT G/RA film and a higher contrast in the high optical density range for comparable exposure latitude. By providing both high sensitivity and high spatial resolution, the new film significantly improves the compromise between dose and image quality. As expected, the new film has a higher noise level and a lower signal-to-noise ratio than the standard film, although in the high frequency range this is compensated for by a better resolution, giving better DQE results--especially at high optical density. Both screen-film systems outperform the phosphor plates in terms of MTF and DQE for standard imaging conditions (Regular screen at RQA 5 and RQA 9 beam qualities). At low energy (RQA 3), the CR system has a comparable low-frequency DQE to screen-film systems when used with a fine screen at low and middle optical densities, and a superior low-frequency DQE at high optical density.

A wearable system to time gate crossing during alpine skiing slalom

INTRODUCTION: In alpine skiing, chronometry analysis is currently the most common tool to assess performance. It is widely used to rank competitors during races, as well as to manage athletes training and to evaluate material. Usually, this measurement is accurately realized using timing cells. Nevertheless, these devices are too complex and expensive to allow chronometry of every gates crossing. On the other side, differential GPS can be used for measuring gate crossing time (Waegli et al). However, this is complex (e.g. recording gate position with GPS) and mainly used in research applications. The aim of the study was to propose a wearable system to time gates crossing during alpine skiing slalom (SL), which is suitable for routine uses. METHODS: The proposed system was composed of a 3D accelerometer (ADXL320®, Analog Device, USA) placed at the sacrum of the athlete, a matrix of force sensors (Flexiforce®, Tekscan, USA) fixed on the right shin guard and a data logger (Physilog®, BioAGM, Switzerland). The sensors were sampled at 500 Hz. The crossing time were calculated in two phases. First, the accelerometer was used to detect the curves by considering the maximum of the mediolateral peak acceleration. Then, the force sensors were used to detect the impacts with the gates by considering maximum force variation. In case of non impact, the detection was realized based on the acceleration and features measured at the other gates. In order to assess the efficiency of the system, two different SL were monitored twice for two world cup level skiers, a male SL expert and a female downhill expert. RESULTS AND DISCUSSION: The combination of the accelerometer and force sensors allowed to clearly identify the gate crossing times. When comparing the runs of the SL expert and the downhill expert, we noticed that the SL expert was faster. For example for the first SL, the overall difference between the best run of each athlete was of 5.47s. At each gate, the SL expert increased the time difference slower at the beginning (0.27s/gate) than at the end (0.34s/gate). Furthermore, when comparing the runs of the SL expert, a maximum time difference of 20ms at each gate was noticed. This showed high repeatability skills of the SL expert. In opposite, the downhill expert with a maximum difference time of 1s at each gate was clearly less repeatable. Both skiers were not disturbed by the system. CONCLUSION: This study proposed a new wearable system to automatically time gates crossing during alpine skiing slalom combining force and accelerometer sensors. The system was evaluated with two professional world cup skiers and showed a high potential. This system could be extended to time other parameters. REFERENCES Waegli A, Skaloud J (2007). Inside GNSS, Spring, 24-34.

Threading libraries performance when applied to image acquisition and processing in a forensic application

Peer-reviewed

System identification using a linear combination of cumulant slices

In this paper we develop a new linear approach to identify the parameters of a moving average (MA) model from the statistics of the output. First, we show that, under some constraints, the impulse response of the system can be expressed as a linear combination of cumulant slices. Then, thisresult is used to obtain a new well-conditioned linear methodto estimate the MA parameters of a non-Gaussian process. Theproposed method presents several important differences withexisting linear approaches. The linear combination of slices usedto compute the MA parameters can be constructed from dif-ferent sets of cumulants of different orders, providing a generalframework where all the statistics can be combined. Further-more, it is not necessary to use second-order statistics (the autocorrelation slice), and therefore the proposed algorithm stillprovides consistent estimates in the presence of colored Gaussian noise. Another advantage of the method is that while mostlinear methods developed so far give totally erroneous estimates if the order is overestimated, the proposed approach doesnot require a previous estimation of the filter order. The simulation results confirm the good numerical conditioning of thealgorithm and the improvement in performance with respect to existing methods.

Evaluation of performance analysis software for Linux computing cluster

Tietokonejärjestelmän osien ja ohjelmistojen suorituskykymittauksista saadaan tietoa,jota voidaan käyttää suorituskyvyn parantamiseen ja laitteistohankintojen päätöksen tukena. Tässä työssä tutustutaan suorituskyvyn mittaamiseen ja mittausohjelmiin eli ns. benchmark-ohjelmistoihin. Työssä etsittiin ja arvioitiin eri tyyppisiä vapaasti saatavilla olevia benchmark-ohjelmia, jotka soveltuvat Linux-laskentaklusterin suorituskyvynanalysointiin. Benchmarkit ryhmiteltiin ja arvioitiin testaamalla niiden ominaisuuksia Linux-klusterissa. Työssä käsitellään myös mittausten tekemisen ja rinnakkaislaskennan haasteita. Benchmarkkeja löytyi moneen tarkoitukseen ja ne osoittautuivat laadultaan ja laajuudeltaan vaihteleviksi. Niitä on myös koottu ohjelmistopaketeiksi, jotta laitteiston suorituskyvystä saisi laajemman kuvan kuin mitä yhdellä ohjelmalla on mahdollista saada. Olennaista on ymmärtää nopeus, jolla dataa saadaan siirretyä prosessorille keskusmuistista, levyjärjestelmistä ja toisista laskentasolmuista. Tyypillinen benchmark-ohjelma sisältää paljon laskentaa tarvitsevan matemaattisen algoritmin, jota käytetään tieteellisissä ohjelmistoissa. Benchmarkista riippuen tulosten ymmärtäminen ja hyödyntäminen voi olla haasteellista.

Evaluation of a piezoelectric system as an alternative to electroencephalogram/ electromyogram recordings in mouse sleep studies.

STUDY OBJECTIVES: Traditionally, sleep studies in mammals are performed using electroencephalogram/electromyogram (EEG/EMG) recordings to determine sleep-wake state. In laboratory animals, this requires surgery and recovery time and causes discomfort to the animal. In this study, we evaluated the performance of an alternative, noninvasive approach utilizing piezoelectric films to determine sleep and wakefulness in mice by simultaneous EEG/EMG recordings. The piezoelectric films detect the animal's movements with high sensitivity and the regularity of the piezo output signal, related to the regular breathing movements characteristic of sleep, serves to automatically determine sleep. Although the system is commercially available (Signal Solutions LLC, Lexington, KY), this is the first statistical validation of various aspects of sleep. DESIGN: EEG/EMG and piezo signals were recorded simultaneously during 48 h. SETTING: Mouse sleep laboratory. PARTICIPANTS: Nine male and nine female CFW outbred mice. INTERVENTIONS: EEG/EMG surgery. MEASUREMENTS AND RESULTS: The results showed a high correspondence between EEG/EMG-determined and piezo-determined total sleep time and the distribution of sleep over a 48-h baseline recording with 18 mice. Moreover, the piezo system was capable of assessing sleep quality (i.e., sleep consolidation) and interesting observations at transitions to and from rapid eye movement sleep were made that could be exploited in the future to also distinguish the two sleep states. CONCLUSIONS: The piezo system proved to be a reliable alternative to electroencephalogram/electromyogram recording in the mouse and will be useful for first-pass, large-scale sleep screens for genetic or pharmacological studies. CITATION: Mang GM, Nicod J, Emmenegger Y, Donohue KD, O'Hara BF, Franken P. Evaluation of a piezoelectric system as an alternative to electroencephalogram/electromyogram recordings in mouse sleep studies.

Performance analysis of software run-time behaviour using 3D-visualisation

Monimutkaisen tietokonejärjestelmän suorituskykyoptimointi edellyttää järjestelmän ajonaikaisen käyttäytymisen ymmärtämistä. Ohjelmiston koon ja monimutkaisuuden kasvun myötä suorituskykyoptimointi tulee yhä tärkeämmäksi osaksi tuotekehitysprosessia. Tehokkaampien prosessorien käytön myötä myös energiankulutus ja lämmöntuotto ovat nousseet yhä suuremmiksi ongelmiksi, erityisesti pienissä, kannettavissa laitteissa. Lämpö- ja energiaongelmien rajoittamiseksi on kehitetty suorituskyvyn skaalausmenetelmiä, jotka edelleen lisäävät järjestelmän kompleksisuutta ja suorituskykyoptimoinnin tarvetta. Tässä työssä kehitettiin visualisointi- ja analysointityökalu ajonaikaisen käyttäytymisen ymmärtämisen helpottamiseksi. Lisäksi kehitettiin suorituskyvyn mitta, joka mahdollistaa erilaisten skaalausmenetelmien vertailun ja arvioimisen suoritusympäristöstä riippumatta, perustuen joko suoritustallenteen tai teoreettiseen analyysiin. Työkalu esittää ajonaikaisesti kerätyn tallenteen helposti ymmärrettävällä tavalla. Se näyttää mm. prosessit, prosessorikuorman, skaalausmenetelmien toiminnan sekä energiankulutuksen kolmiulotteista grafiikkaa käyttäen. Työkalu tuottaa myös käyttäjän valitsemasta osasta suorituskuvaa numeerista tietoa, joka sisältää useita oleellisia suorituskykyarvoja ja tilastotietoa. Työkalun sovellettavuutta tarkasteltiin todellisesta laitteesta saatua suoritustallennetta sekä suorituskyvyn skaalauksen simulointia analysoimalla. Skaalausmekanismin parametrien vaikutus simuloidun laitteen suorituskykyyn analysoitiin.

Performance of 'Rocha' and 'Santa Maria' pears as affected by planting density

The objective of this work was to evaluate the performance of 'Rocha' and 'Santa Maria' pears at two planting densities. The experiment was carried out during the 2011/2012, 2012/2013, and 2013/2014 growing seasons, in one-year-old orchards (2011/2012) of 'Rocha' and 'Santa Maria' pears, trained in a central-leader system and planted in two densities (2,000 and 4,000 trees per hectare). The assessed parameters were: production per hectare, production per tree, yield efficiency, number of fruit per tree, average fruit weight, trunk diameter increment, fruit firmness, and soluble solid contents. The cumulative yield of 'Rocha' is greater at the higher planting density, whereas the yield efficiency of 'Santa Maria' increases at the lower planting density, as the trees get more mature. Trunk diameter of 'Rocha' also increases at the lower planting density. However, fruit quality parameters in both cultivars are little affected by planting density.

Container Handling Equipment Monitoring System, case: Steveco Oy

Container Handling Equipment Monitoring System (CHEMS) is a system developed by Savcor One Oy. CHEMS measures important information for container ports performance and produces performance indicators. The aim of this thesis was to clarify performance measurement contents to Savcor and to develop, as an example, performance measures to Steveco Oy's container operations. The theoretical part of the thesis clarifies performance measurement and which of its components are important to container port. Performance measurement and measures are presented from the operational level's point of view, in which CHEMS is planned to aim. The theory of development process of performance measures is introduced at the end of the theoretical part. To make sure that performance measures are efficiently used, Steveco Oy's performance measures are developed in cooperation with the users. The measurement in operational level is continuous and the results must be reacted asquickly as possible. CHEMS is very suitable to continuous measurement and to produce real time-measures of container operations which are hard to get any otherway.

Short-term Hydropower Planning System

The Thesis gives a decision support framework that has significant impact on the economic performance and viability of a hydropower company. The studyaddresses the short-term hydropower planning problem in the Nordic deregulated electricity market. The basics of the Nordic electricity market, trading mechanisms, hydropower system characteristics and production planning are presented in the Thesis. The related modelling theory and optimization methods are covered aswell. The Thesis provides a mixed integer linear programming model applied in asuccessive linearization method for optimal bidding and scheduling decisions inthe hydropower system operation within short-term horizon. A scenario based deterministic approach is exploited for modelling uncertainty in market price and inflow. The Thesis proposes a calibration framework to examine the physical accuracy and economic optimality of the decisions suggested by the model. A calibration example is provided with data from a real hydropower system using a commercial modelling application with the mixed integer linear programming solver CPLEX.

Breeding objectives for a Nellore cattle rearing system

Abstract:The objective of this work was to define the traits that should be included as breeding objectives for Nellore cattle, according to simulations with a bio-economic model for rearing systems. The economic values (EVs) of the traits were calculated as the differences between the profits due to an increased performance of 1% in each trait, with the others traits remaining constant. To determine the impact of each selection on the revenue system, two scenarios were simulated based on the traits being selected. In the first scenario, the adopted selection criteria were: weaning weight (WW), weaning rate (WR), yearling weight (YW), and mature cow weight (MCW). In the second scenario, the cumulative productivity (CP) of dams was used as an indirect evaluation of the performance of calves, with all the other traits included, except WW. In the first scenario, an EV of R$ 1.44 kg-1 was obtained for WW. In the second scenario, an EV of R$ 2.91 kg-1 was obtained for CP. The trait with the highest EV in both scenarios was WR, which enhanced the profits by R$ 3.21 for each 1% increased performance. The meat price paid to the producer is the factor with the greatest impact on the EVs of all examined traits.

Reporting Framework: Implementation and Performance Analysis

Fenix on suuri metsäteollisuuden tuotannonohjausjärjestelmä. Fenix-järjestelmän raportointi- ja tulostuspalvelut elävätvaihdekautta. Aikaisemmin käytetyt raportointityökalut ovat vanhentumassa ja neon korvattava uusilla. Uusi raportointialusta, Global Printing System (GPS), onrakennettu StreamServe Business Communication Platformin ympärille. Uuden alustan on tarkoitus hoitaa Fenixin tulostus sekä raportointitehtävät. Työ kuvaa raportointialustan toteutuksen sekä sen tärkeimmät ominaisuudet. Uuden alustan suorituskyvyssä on ollut toivomisen varaa. Etenkin suurien raporttien generoiminen on kestänyt joskus toivottoman pitkään. Työssä analysoidaan raportointialustan suorituskykyä ja etsitään mahdolliset pullonkaulat. Suorituskyvyn heikkouksiin pyritään löytämään ratkaisut ja annetaan ehdotuksia suorituskyvyn parantamiseksi. XML pohjaisena järjestelmänä GPS:n suorituskyvyssä suurta osaaesittää XML:n tehokkuus. GPS sisääntuleva data tulee XML-muodossa ja sisääntulon parsimisen tehokkuus on avaintekijöitä koko GPS:n tehokkuuden kannalta. Suorituskyvyn parantamisessa keskitytäänki vahvasti XML:n tehokkaampaan käyttöön ja esitetään ehdotuksia sen parantamiseksi.

Machine vision measurement system for paper printability assessments

This work had two primary objectives: 1) to produce a working prototype for automated printability assessment and 2) to perform a study of available machine vision and other necessary hardware solutions. The three printability testing methods, IGT Picking,He¬liotest, and mottling, considered in this work have several different requirements and the task was to produce a single automated testing system suitable for all methods. A system was designed and built and its performance was tested using the Heliotest. Working proto¬types are important tools for implementing theoretical methods into practical systems and testing and demonstrating the methodsin real life conditions. The system was found to be sufficient for the Heliotest method. Further testing and possible modifications related to other two test methods were left for future works. A short study of available systems and solutions concerning image acquisition of machine vision was performed. The theoretical part of this study includes lighting systems, optical systems and image acquisition tools, mainly cameras and the underlying physical aspects for each portion.