Development of power flows around Baltic countries with new grid links

In the Thesis main focus is done on power flow development paths around the Baltic States as well as on market-based requirements for creation of the common Baltic electricity market. Current market regulations between the countries are presented; barriers for creating competitive common Baltic power market and for electricity trading with third countries are clarified; solutions are offered and corresponding road map is developed. Future power development paths around the Baltic States are analysed. For this purpose the 330 kV transmission grid of Estonia, Latvia and Lithuania is modelled in a power flow tool. Power flow calculations are carried out for winter and summer peak and off-peak load periods in 2020 with different combinations of interconnections. While carrying out power balance experiments several power flow patterns in the Baltic States are revealed. Conclusions are made about security of supply, grid congestion and transmission capacity availability for different scenarios.

Electrical machine in a Hybrid Electrical Vehicle

Hybrid electric vehicles (HEV) have attracted very much attention during the latest years. Increasing environmental concern and an increase in fuel prices are key factors for the growing interest towards the HEV. In a hybrid electric vehicle the power train consists of both a mechanical power system and an electric power transmission system. The major subsystems in the mechanical power system are the internal combustion engine which powers the vehicle; electric power transmission including an energy storage, power electronic inverter, hybrid control system; the electric motor drive that runs either in the generating mode or in the motoring mode to process the power flow between the energy storage and the electrical machine. This research includes two advanced electric motors for a parallel hybrid: induction machine and permanent magnets synchronous machine. In the thesis an induction motor and a permanent magnet motor are compared as propulsion motors. Electric energy storages are also studied.

Flow analysis by using solenoid valves for As(III) determination in natural waters by an on-line separation and pre-concentration system coupled to a tungsten coil atomizer

A flow system coupled to a tungsten coil atomizer in an atomic absorption spectrometer (TCA-AAS) was developed for As(III) determination in waters, by extraction with sodium diethyldithiocarbamate (NaDDTC) as complexing agent, and by sorption of the As(III)-DDTC complex in a micro-column filled with 5 mg C18 reversed phase (10 µL dry sorbent), followed by elution with ethanol. A complete pre-concentration/elution cycle took 208 s, with 30 s sample load time (1.7 mL) and 4 s elution time (71 µL). The interface and software for the synchronous control of two peristaltic pumps (RUN/ STOP), an autosampler arm, seven solenoid valves, one injection valve, the electrothermal atomizer and the spectrometer Read function were constructed. The system was characterized and validated by analytical recovery studies performed both in synthetic solutions and in natural waters. Using a 30 s pre-concentration period, the working curve was linear between 0.25 and 6.0 µg L-1 (r = 0.9976), the retention efficiency was 94±1% (6.0 µg L-1), and the pre-concentration coefficient was 28.9. The characteristic mass was 58 pg, the mean repeatability (expressed as the variation coefficient) was 3.4% (n=5), the detection limit was 0.058 µg L-1 (4.1 pg in 71 µL of eluate injected into the coil), and the mean analytical recovery in natural waters was 92.6 ± 9.5 % (n=15). The procedure is simple, economic, less prone to sample loss and contamination and the useful lifetime of the micro-column was between 200-300 pre-concentration cycles.

Brain Computer Interface for Virtual Reality Control

A brain-computer interface (BCI) is a new communication channel between the human brain and a computer. Applications of BCI systems comprise the restoration of movements, communication and environmental control. In this study experiments were made that used the BCI system to control or to navigate in virtual environments (VE) just by thoughts. BCI experiments for navigation in VR were conducted so far with synchronous BCI and asynchronous BCI systems. The synchronous BCI analyzes the EEG patterns in a predefined time window and has 2 to 3 degrees of freedom.

Erikoissähkökoneen tyyppitestaus

Uusien erikoissähkökoneiden testaus perinteisten standardien mukaan on osittain haasteellista. Erikoissähkökoneille, kuten kestomagneettitahtikoneelle ei ole esitetty suoranaisia standardin vaatimia testejä, joten siihen joudutaan soveltamaan olemassa olevia erillismagnetoiduntahtikoneen standardeja. Testien tavoitteena on olla luotettavia sekä vertailukelpoisia. Mittausten on oltava toistettavissa. Mittaustavasta riippuen voidaan saada erilaisia tuloksia, jotka vaikuttavat lopputulokseen. Standardien mukaisessa testauksessa saadaan mittauksista samanlaisia ja samalla saadaan mittausvirheen mahdollisuus pienemmäksi ja tällä tavoin tulokset keskenään vertailukelpoisemmiksi. Tässä työssä tarkastellaan kahta erilaista erikoissähkokonetta, kestomagneettitahtikonetta ja massiiviroottoriepätahtikonetta. Työssä selvitetään standardin IEC 60034 soveltuvuutta tyyppitesteihin, joita kyseiset konetyypit vaativat. Lisäksi työssä vertaillaan standardin IEC 60034 mukaisen hyötysuhteen määrittämistä. Se antaakin useita vaihtoehtoja hyötysuhteen määrittämiselle.

Formal Power Analysis of Systems-on-Chip

The design methods and languages targeted to modern System-on-Chip designs are facing tremendous pressure of the ever-increasing complexity, power, and speed requirements. To estimate any of these three metrics, there is a trade-off between accuracy and abstraction level of detail in which a system under design is analyzed. The more detailed the description, the more accurate the simulation will be, but, on the other hand, the more time consuming it will be. Moreover, a designer wants to make decisions as early as possible in the design flow to avoid costly design backtracking. To answer the challenges posed upon System-on-chip designs, this thesis introduces a formal, power aware framework, its development methods, and methods to constraint and analyze power consumption of the system under design. This thesis discusses on power analysis of synchronous and asynchronous systems not forgetting the communication aspects of these systems. The presented framework is built upon the Timed Action System formalism, which offer an environment to analyze and constraint the functional and temporal behavior of the system at high abstraction level. Furthermore, due to the complexity of System-on-Chip designs, the possibility to abstract unnecessary implementation details at higher abstraction levels is an essential part of the introduced design framework. With the encapsulation and abstraction techniques incorporated with the procedure based communication allows a designer to use the presented power aware framework in modeling these large scale systems. The introduced techniques also enable one to subdivide the development of communication and computation into own tasks. This property is taken into account in the power analysis part as well. Furthermore, the presented framework is developed in a way that it can be used throughout the design project. In other words, a designer is able to model and analyze systems from an abstract specification down to an implementable specification.

Characterizing Propionibacterium freudenreichii ssp. shermanii JS and Lactobacillus rhamnosus LC705 as a new probiotic combination: basic properties of JS and pilot in vivo assessment of the combination

Characterizing Propionibacterium freudenreichii ssp. shermanii JS and Lactobacillus rhamnosus LC705 as a new probiotic combination: basic properties of JS and pilot in vivo assessment of the combination Each candidate probiotic strain has to have the documentation for the proper identification with current molecular tools, for the biological properties, for the safety aspects and for the health benefits in human trials if the intention is to apply the strain as health promoting culture in the commercial applications. No generalization based on species properties of an existing probiotic are valid for any novel strain, as strain specific differences appear e.g. in the resistance to GI tract conditions and in health promoting benefits (Madsen, 2006). The strain evaluation based on individual strain specific probiotic characteristics is therefore the first key action for the selection of the new probiotic candidate. The ultimate goal in the selection of the probiotic strain is to provide adequate amounts of active, living cells for the application and to guarantee that the cells are physiologically strong enough to survive and be biologically active in the adverse environmental conditions in the product and in GI tract of the host. The in vivo intervention studies are expensive and time consuming; therefore it is not rational to test all the possible candidates in vivo. Thus, the proper in vitro studies are helping to eliminate strains which are unlikely to perform well in vivo. The aims of this study were to characterize the strains of Propionibacterium freudenreichii ssp. shermanii JS and Lactobacillus rhamnosus LC705, both used for decades as cheese starter cultures, for their technological and possible probiotic functionality applied in a combined culture. The in vitro studies of Propionibacterium freudenreichii ssp. shermanii JS focused on the monitoring of the viability rates during the acid and bile treatments and on the safety aspects such as antibiotic susceptibility and adhesion. The studies with the combination of the strains JS and LC705 administered in fruit juices monitored the survival of the strains JS and LC705 during the GI transit and their effect on gut wellbeing properties measured as relief of constipation. In addition, safety parameters such as side effects and some peripheral immune parameters were assessed. Separately, the combination of P. freudenreichii ssp. shermanii JS and Lactobacillus rhamnosus LC705 was evaluated from the technological point of view as a bioprotective culture in fermented foods and wheat bread applications. In this study, the role ofP. freudenreichii ssp. shermanii JS as a candidate probiotic culture alone and in a combination with L. rhamnosus LC705 was demonstrated. Both strains were transiently recovered in high numbers in fecal samples of healthy adults during the consumption period. The good survival through the GI transit was proven for both strains with a recovery rate from 70 to 80% for the JS strain and from 40 to 60% for the LC705 strain from the daily dose of 10 log10 CFU. The good survival was shown from the consumption of fruit juices which do not provide similar matrix protection for the cells as milk based products. The strain JS did not pose

Concentrated Winding Multiphase Permanent Magnet Machine Design and Electromagnetic Properties – Case Axial Flux Machine

Concentrated winding permanent magnet machines and their electromagnetic properties are studied in this doctoral thesis. The thesis includes a number of main tasks related to the application of permanent magnets in concentrated winding open slot machines. Suitable analytical methods are required for the first design calculations of a new machine. Concentrated winding machines differ from conventional integral slot winding machines in such a way that adapted analytical calculation methods are needed. A simple analytical model for calculating the concentrated winding axial flux machines is provided. The next three main design tasks are discussed in more detail in the thesis. The magnetic length of the rotor surface magnet machines is studied, and it is shown that the traditional methods have to be modified also in this respect. An important topic in this study has been to evaluate and minimize the rotor permanent magnet Joule losses by using segmented magnets in the calculations and experiments. Determination of the magnetizing and leakage inductances for a concentrated winding machine and the torque production capability of concentrated winding machines with different pole pair numbers are studied, and the results are compared with the corresponding properties of integral slot winding machines. The thesis introduces a new practical permanent magnet motor type for industrial use. The special features of the machine are based on the option of using concentrated winding open slot constructions of permanent magnet synchronous machines in the normal speed ranges of industrial motors, for instance up to 3000 min-1, without excessive rotor losses. By applying the analytical equations and methods introduced in the thesis, a 37 kW 2400 min-1 12-slot 10-pole axial flux machine with rotor-surfacemounted magnets is designed. The performance of the designed motor is determined by experimental measurements and finite element calculations.

Análise de fluorescência de substâncias húmicas extraídas da água, solo e sedimento da Lagoa dos Patos - MS

The humic substances were extracted from sediments, water and soil close to the Lagoa dos Patos-MS. The characterization was performed through fluorescence emission. In the HSs it is possible to see strong indications of incorporation of compounds originating from lignin degradation, confirmed by fluorescence emission (EEM and synchronous spectra). These differences observed in HSs may be due to tropical regions displaying a great variety of vascular plants and aquatic macrophytes that contribute natural organic matter. The seasonality effect also causes the entrance of pedogenic material and the suspension of sediments by the action of winds.

Substitutos do " novo" mundo para as antigas plantas raras: um estudo de caso dos bálsamos

Convinced that the " true balsam" was lost forever, Conrad Gesner described other substances with similar healing virtues. However, he was not the only one in the 16th to search for other varieties of balsamic oleoresins. The arrival of the Europeans to the Americas allowed the finding of native plants with properties similar to those of the original balsam, including Balsam of Peru, Balsam of Tolu and particularly in the Brazilian area, Balsam of Copaiba. Focusing on the Brazilian context, this paper analyzes two different moments in the transit of the newly found varieties of balsams to the pharmacopeia and materia medica.

Development of Russian Ports in The Gulf of Finland

Russia has been one of the fastest developing economic areas in the world. Based on the GDP, the Russian economy grew evenly since the crisis in 1998 up till 2008. The growth in the gross domestic product has annually been some 5–10%. In 2007, the growth reached 8.1%, which is the highest figure after the 10% growth in 2000. Due to the growth of the economy and wage levels, purchasing power and consumption have been strongly increasing. The growing consumption has especially increased the imports of durables, such as passenger cars, domestic appliances and electronics. The Russian ports and infrastructure have not been able to satisfy the growing needs of exports and imports, which is why quite a large share of Russian foreign trade is going through third countries as transit transports. Finnish ports play a major role in transit transports to and from Russia. About 15% of the total value of Russian imports was transported through Finland in 2008. The economic recession that started in autumn 2008 and continues to date has had an impact on the economic development of Russia. The export income has decreased, mainly due to the reduced world market prices of energy products (oil and gas) and raw minerals. Investments have been postponed, getting credit is more difficult than before, and the ruble has weakened in relation to the euro and the dollar. The imports are decreasing remarkably, and are not forecast to reach the 2008 volumes even in 2012. The economic crisis is reflected in Finland's transit traffic. The volume of goods transported through Finland to and from Russia has decreased almost in the same proportion as the imports of goods to Russia. The biggest risk threatening the development of the Russian economy over long term is its dependence on export income from oil, gas, metals, minerals and forest products, as well as the trends of the world market prices of these products. Nevertheless, it is expected that the GDP of Russia will start to grow again in the forthcoming years due to the increased demand for energy products and raw minerals in the world. At the same time, it is obvious that the world market prices of these products will go up with the increasing demand. The increased income from exports will lead to a growth of imports, especially those of consumer goods, as the living standard of Russian citizens rises. The forecasts produced by the Russian Government concerning the economic development of Russia up till 2030 also indicate a shift in exported goods from raw materials to processed products, which together with energy products will become the main export goods of Russia. As a consequence, Russia may need export routes through third countries, which can be seen as an opportunity for increased transit transports through the ports of Finland. The ports competing with the ports of Finland for Russian foreign trade traffic are the Russian Baltic Sea ports and the ports of the Baltic countries. The strongest competitors are the Baltic Sea ports handling containers. On the Russian Baltic Sea, these ports include Saint Petersburg, Kaliningrad and, in the near future, the ports of Ust-Luga and possibly Vyborg. There are plans to develop Ust-Luga and Vyborg as modern container ports, which would become serious competitors to the Finnish ports. Russia is aiming to redirect as large a share as possible of foreign trade traffic to its own ports. The ports of Russia and the infrastructure associated with them are under constant development. On the other hand, the logistic capacity of Russia is not able to satisfy the continually growing needs of the Russian foreign trade. The capacity problem is emphasized by a structural incompatibility between the exports and imports in the Russian foreign trade. Russian exports can only use a small part of the containers brought in with imports. Problems are also caused by the difficult ice conditions and narrow waterways leading to the ports. It is predicted that Finland will maintain its position as a transit route for the Russian foreign trade, at least in the near future. The Russian foreign trade is increasing, and Russia will not be able to develop its ports in proportion with the increasing foreign trade. With the development of port capacity, cargo flows through the ports of Russia will grow. Structural changes in transit traffic are already visible. Firms are more and more relocating their production to Russia, for example as regards the assembly of cars and warehousing services. Simultaneously, an increasing part of transit cargoes are sent directly to Russia without unloading and reloading in Finland. New product groups have nevertheless been transported through Finland (textile products and tools), replacing the lost cargos. The global recession that started in autumn 2008 has influenced the volume of Russian imports and, consequently, the transit volumes of Finland, but the recession is not expected to be of long duration, and will thus only have a short-term impact on transit volumes. The Finnish infrastructure and services offered by the logistic chain should also be ready to react to the changes in imported product groups as well as to the change in Russian export products in the future. If the development plans of the Russian economy are realized, export products will be more refined, and the share of energy and raw material products will decrease. The other notable factor to be taken into consideration is the extremely fast-changing business environment in Russia. Operators in the logistic chain should be flexible enough to adapt to all kinds of changes to capitalise on business opportunities offered by the Russian foreign trade for the companies and for the transit volumes of Finnish ports, also in the future.

Engineering of Business Critical Web Applications

Research focus of this thesis is to explore options for building systems for business critical web applications. Business criticality here includes requirements for data protection and system availability. The focus is on open source software. Goals are to identify robust technologies and engineering practices to implement such systems. Research methods include experiments made with sample systems built around chosen software packages that represent certain technologies. The main research focused on finding a good method for database data replication, a key functionality for high-availability, database-driven web applications. Research included also finding engineering best practices from books written by administrators of high traffic web applications. Experiment with database replication showed, that block level synchronous replication offered by DRBD replication software offered considerably more robust data protection and high-availability functionality compared to leading open source database product MySQL, and its built-in asynchronous replication. For master-master database setups, block level replication is more recommended way to build high-availability into the system. Based on thesis research, building high-availability web applications is possible using a combination of open source software and engineering best practices for data protection, availability planning and scaling.

Hybrid du/dt-filter in frequency converter applications

The aim of the thesis is to investigate the hybrid LC filter behavior in modern power drives; to analyze the influence of such a du/dt filter on the control system stability. With the implementation of the inverter output RLC filter the motor control becomes more complicated. And during the design process the influence of the filter on the motor should be considered and the filter RLC parameters should be constrained.

Electric propulsion system in a modern sports car

In this thesis an electric propulsion system is designed on a device level using Cadence ORCAD. The vehicle belongs to the Helsinki Metropolia University of Applied Sci-ences and it is to compete in the Automotive X-Prize competition held in the USA. In this thesis the electric propulsion system and related electric safety measures are designed. Also electro-magnetic compatibility and interferences present in the system are examined by examining the birth mechanisms and transmission paths of interference. Per device effects of interference and solutions to minimize them were examined and proposed. Suitability of permanent magnet synchronous machines for passenger vehicle use was examined by examining the torque production capability of the motor and the torque requirements of the vehicle. Also a short overview of history of electric vehicles is given.

Kestomagneettitahtikoneen emulointi digitaalisella signaaliprosessorilla

Sähkökäytön suunnittelussa säätöä voidaan testata useassa tapauksessa reaaliaikasimulaattorilla todellisen laitteiston sijaan. Monet reaaliaikasimulaatioiden perustana käytetyt algoritmit soveltuvat täysinohjatulle invertterisillalle. Eräissä sovelluksissa halutaan kuitenkin käyttää puoliksiohjattua siltaa. Puoliksiohjattulla sillalla mallin kausaalisuus voi kääntyä, mitä perinteiset reaaliaikasimulaattorit eivät pysty simuloimaan Tässä työssä oli tavoitteena kehittää reaaliaikasimulaattori puoliksiohjatulle kestomagneettitahtikonekäytölle. Emulaattoriin mallinnettiin todellisen käytön kestomagneettitahtikone ja invertterisilta. Simulaattori toteutettiin digitaaliselle signaaliprosessorille (DSP) ja mittauksiin liittyvät oheislaitteet mallinnettiin FPGA-piirille. Emulaattoriin liitettiin erillinen säätäjä, jota käytettiin myös todellisen sähkökäytön säätämiseen. Emulaattorilla ja todellisella käytöllä tehtyjä mittauksia verrattiin ja emuloimalla saadut tulokset vastasivat melko hyvin todellisesta käytöstä mitattuja.