Análise microbiológica da cavidade interna de implantes dentais osseointegrados utilizando o checkerboard DNA-DNA hybridization

Introduction: Infiltration of organic fluids and microorganisms at the abutment/implant interface may result in bacterial infection of peri-implant tissues. Internal colonization of periodontal pathogens may be caused by bacteria trapped during installation or penetration of abutment/implant leakage. The aim of this study was to detect periodontal pathogens in the internal area of dental implants before loading. Materials and Methods: Seventy-eight implants in 32 partially edentulous subjects were selected for this evaluation. A bacterial biofilm sample of the internal surface of each implant was taken and analyzed for the presence of 40 microorganisms by checkerboard DNA-DNA hybridization, prior to installation of healing or any other prosthetic abutment. Discussion: Bacteria were detected in 20 patients (62.5%), distributed in 41 implants (52.6%). Forty-seven percent of implants showed no bacterial detection. Spontaneous early implant exposure to oral cavity during the healing period was not significant (P >0.05) to increase bacterial prevalence, but implants placed at mandible had higher bacterial prevalence than maxillary ones. Conclusion: The internal surface of dental implants can serve as a reservoir of periodontal pathogens for future implant/abutment interface.

Molecular diversity, cultivation, and improved detection by fluorescent in situ hybridization of a dominant group of human gut bacteria related to Roseburia spp. or Eubacterium rectale

Peer reviewed

Molecular diversity, cultivation, and improved detection by fluorescent in situ hybridization of a dominant group of human gut bacteria related to Roseburia spp. or Eubacterium rectale

Peer reviewed

Gonadotrophin-releasing hormone agonist protocols for pituitary suppression in assisted reproduction

Peer reviewed

Suppression of neuronal phase synchronisation in cat cerebral cortex

We wish to acknowledge the support of the Brazilian agencies: CNPq, CAPES, and FAPESP (2015/07311-7 and 2011/19296-1).

Passive bridge deck-flaps system for suppression of flutter in long span bridges

Peer reviewed

Study no the passive deck-flap flutter suppression system on FEM model of the bridge

Peer reviewed

Full bridge model study of a passive aerodynamic flutter suppression system

Peer reviewed

Suppression of phase synchronisation in network based on cat’s brain

We wish to acknowledge the support of the Brazilian agencies: CNPq, CAPES, and FAPESP (2015/07311-7 and 2011/19296-1).

Mécanismes de suppression tumorale impliqués lors de la sénescence induite par les oncogènes

Thèse numérisée par la Direction des bibliothèques de l'Université de Montréal.

Étude de l'activité physique de suppression tumorale de la protéine KBP2 dans les lignées de cellules de carcinome du sein MCF7

Mémoire numérisé par la Direction des bibliothèques de l'Université de Montréal.

Subtractive and additive manufacturing technology in moulding industry

This report is a review of additive and subtractive manufacturing techniques. This approach (additive manufacturing) has resided largely in the prototyping realm, where the methods of producing complex freeform solid objects directly from a computer model without part-specific tooling or knowledge. But these technologies are evolving steadily and are beginning to encompass related systems of material addition, subtraction, assembly, and insertion of components made by other processes. Furthermore, these various additive processes are starting to evolve into rapid manufacturing techniques for mass-customized products, away from narrowly defined rapid prototyping. Taking this idea far enough down the line, and several years hence, a radical restructuring of manufacturing could take place. Manufacturing itself would move from a resource base to a knowledge base and from mass production of single use products to mass customized, high value, life cycle products, majority of research and development was focused on advanced development of existing technologies by improving processing performance, materials, modelling and simulation tools, and design tools to enable the transition from prototyping to manufacturing of end use parts.

Suppression of nonlinear distortion in few-mode fibres using strong mode coupling

In this paper, we investigate the impact of linear mode coupling on the efficiency of intermodal four-wave mixing and on the group delay statistics in few-mode fibres. The investigation will include not only the weak or strong linear coupling regimes, but also the transition region between them, the intermediate coupling regime. This analysis will allow to assess the level of coupling strength require to suppress the nonlinear distortion in a few-mode fibre below the level of distortion for single-mode propagation without mode coupling.

The relationship between fusion, suppression, and diplopia in amblyopia

Purpose: Traditionally, it has been thought that no binocular combination occurs in amblyopia. However, there is a growing body of evidence that there are intact binocular mechanisms in amblyopia rendered inactive under normal viewing conditions due to imbalanced monocular inputs. Georgeson and Wallis (2014) recently introduced a novel method to investigate fusion, suppression and diplopia in normal population. We have modified this method to assess binocular interactions in amblyopia. Methods: Ten amblyopic and ten control subjects viewed briefly-presented (200 ms) pairs of dichoptically separated horizontal Gaussian blurred edges. Subjects reported one central edge, one offset edge, or a double edge as the vertical disparity was manipulated. The experiment was conducted at a range of spatial scales (blur widths of 4, 8, 16, and 32 arc min) and contrasts. Our model, based Georgeson and Wallis (2014), converted subjects’ responses into probabilities of fusion, suppression, and diplopia. Results: When the normal participants were presented equal contrast to each eye the probability of fusion gradually decreased with increasing disparity, as the probability of diplopia gradually increased. In only a small proportion of the trials, normal participants experienced suppression. The pattern was consistent across all edge blurs. Interestingly, the majority of amblyopes had a comparable pattern of fusion, i.e. decreasing probability with increasing disparity. However, with increasing disparity the amblyopes tended to suppress the amblyopic eye, experiencing diplopia only in a small proportion of trials particularly at large blurs. Increasing the interocular contrast offset favouring the amblyopic eye normalized the pattern of data in a way similar to normal participants. There were some interesting exceptions: strong suppressors for which our contrast range was inadequate and one case in which diplopia dominated. Conclusions: This task is suitable for assessing binocular interactions in amblyopic participants and providing a way to quantify the relationship between fusion, suppression and diplopia. In agreement with previous studies, our data indicate the presence of binocular mechanisms in amblyopia. A contrast offset favouring the amblyopic eye normalizes the measured binocular interactions in the amblyopic visual system.

Suppression of patterning effects in digital communications by an adaptive constrained coding

We quantify the error statistics and patterning effects in a 5x 40 Gbit/s WDM RZ-DBPSK SMF/DCF fibre link using hybrid Raman/EDFA amplification. We propose an adaptive constrained coding for the suppression of errors due to patterning effects. It is established, that this coding technique can greatly reduce the bit error rate (BER) value even for large BER (BER > 101). The proposed approach can be used in the combination with the forward error correction schemes (FEC) to correct the errors even when real channel BER is outside the FEC workspace.