Studies on Magnetic Iron Oxide Loaded Activated Carbon

The current water treatment technology is oriented towards the removal of contaminants, mostly organic compounds, by activated carbon. Activated carbons are classified as Granular Activated Carbons (GAC) and Powdered Activated Carbons (PAC) on the basis of the particle size of the carbon granules. Powdered carbons are generally less expensive than granular carbon, operating costs with powdered carbon could be lower. Though powdered activated carbon has many advantages over granular carbon, its application in large-scale separation process is limited by difficulty in recovery and regeneration. Deposition of magnetic iron oxide on carbon particles provides a convenient way of recovering the spent carbon from process water. The study deals with the preparation and physico-chemical characterization of magnetic iron oxide loaded activated carbons. The evaluation of absorption properties of magnetic iron oxide loaded activated carbon composites. The target molecules studied were phenol, p-nitro phenol and methylene blue. The feasibility of magnetic separation of iron oxide loaded activated carbons were studied and described in this thesis.

Lithium Containing Complex Metal Oxides and Metal phosphates:Investigations on their synthesis and various characterizations for rechargeable lithium battery applications

The work presented in the thesis is centered around two important types of cathode materials, the spinel structured LixMn204 (x =0.8to1.2) and the phospho -oIivine structured LiMP04 (M=Fe and Ni). The spinel system LixMn204, especially LiMn204 corresponding to x= 1 has been extensively investigated to understand its structural electrical and electrochemical properties and to analyse its suitability as a cathode material in rechargeable lithium batteries. However there is no reported work on the thermal and optical properties of this important cathode material. Thermal diffusivity is an important parameter as far as the operation of a rechargeable battery is concerned. In LixMn204, the electronic structure and phenomenon of Jahn-Teller distortion have already been established theoretically and experimentally. Part of the present work is an attempt to use the non-destructive technique (NDT) of photoacoustic spectroscopy to investigate the nature of the various electronic transitions and to unravel the mechanisms leading to the phenomenon of J.T distortion in LixMn204.The phospho-olivines LiMP04 (M=Fe, Ni, Mn, Co etc) are the newly identified, prospective cathode materials offering extremely high stability, quite high theoretical specific capacity, very good cycIability and long life. Inspite of all these advantages, most of the phospho - olivines especially LiFeP04 and LiNiP04 show poor electronic conductivity compared to LixMn204, leading to low rate capacity and energy density. In the present work attempts have been made to improve the electronic conductivity of LiFeP04 and LiNiP04 by adding different weight percentage MWNT .It is expected that the addition of MWNT will enhance the electronic conductivity of LiFeP04 and LiNiP04 with out causing any significant structural distortions, which is important in the working of the lithium ion battery.

Targeted Public Distribution System in Food Grains:Extent of Utlization by the Tribal Population in Kerala

In India, Food Security meant supply of food grains and the medium was Public Distribution System. Public Distribution System (PDS) is a rationing mechanism that entitles households to specified quantities of selected commodities at subsidized prices. The Objectives of PDS are maintaining Price Stability, rationing during times of scarcity, welfare of the poor, and keeping a check on private trade. Kerala has registered remarkable improvement in poverty reduction in general over the years among all social sections, including scheduled caste and scheduled tribe population. As part of the structural adjustment intended to reduce public expenditure, PDS has been modified as Revamped PDS (RPDS) during 1992 and later on as Targeted PDS (TPDS) in 1997, intended to target households on the basis of income criterion, classifying people as Below Poverty Line (BPL) and Above Poverty Line (APL). TPDS provides 25Kg. of food gra.ins through the Fair Price Shops per month @ Rs.3/- per Kg. of rice/ wheat to the BPL category and @Rs.8.90 and Rs.6.7O for rice and wheat respectively to the APL category of people. Since TPDS is intended to target the poor people, the subsidy spent by the government for the scheme should be beneficial to the poor people and naturally they should utilize the benefits by purchasing the food grains allotted under the scheme. Several studies have shown that there is underutilization of the allotments under TPDS. Therefore, the extent of utilization of TPDS in food grains, how and why remains as a major hurdle, in improving the structure and system of PDS. Livelihood of the tribal population being under threat due to increasing degradation of the resources, the targeting system ought to be effective among the tribal population. Therefore, performance of the TPDS in food grains, in terms of the utilization by the tribal population in Kerala, impact thereof and the factors, if any, affecting proper utilization were considered as the research problem in this study. The study concentrated on the pattern of consumption of food grains by the tribal people, whether their hunger needs are met by distribution of food grains through the TPDS, extent to which TPDS in food grains reduce their share of expenditure on food in the total household expenditure, and the factors affecting the utilization of the TPDS in food grains by the tribal population. Going through the literature, it has been noted that only few studies concentrated on the utilization of TPDS in food grains among the tribal population in Kerala.The Research Design used in this study is descriptive in nature, but exploratory in some aspects. Idukki, Palakkad and Wayanad have more than 60% of the population of the tribals in the state. Within the three districts mentioned above, 14 villages with scheduled tribe concentration were selected for the study. 95 tribal colonies were selected from among the various tribal settlements. Collection of primary data was made from 1231 households with in the above tribal colonies. Analysis of data on the socio-economic factors of the tribal people, pattern of food consumption, extent of reduction in the share of expenditure on food among the household expenditure of the tribal people and the impact of TPDS on the tribal families etc. and testing of hypotheses to find out the relation/association of each of the six variables, using the data on BPL and APL categories of households separately have resulted in findings such as six percent of the tribal families do not have Ration Cards, average per capita consumption of food grains by the tribal people utilizing TPDS meets 62% of their minimum requirement, whereas the per capita consumption of food grains by the tribal people is higher than the national average per capita consumption, 63% deficiency in food grains may be felt by tribal people in general, if TPDS is withdrawn, and the deficit for BPL tribal people may be 82%, TPDS facilitates a reduction of 9.71% in the food expenditure among the total household expenditure of the tribal people in general, share of food to non-food among BPL category of tribals is 55:45 and 40:60 among the APL, Variables, viz. household income, number of members in the family and distance of FPS from tribal settlements etc. have influence on the quantity of rice being purchased by the tribal people from the Fair Price Shops, and there is influence of household income and distance of FPS from tribal settlements on the quantity of rice being purchased by the tribal people from the open market. Rationing with differential pricing on phased allotments, rectification of errors in targeting, anomalies in norms and procedures for classifying tribal people as BPL/APL, exclusive Income Generation for tribal population, paddy cultivation in the landholdings possessed by the tribal people, special drive for allotment of Ration Cards to the tribal people, especially those belonging to the BPL category, Mobile Fair Price Shops in tribal settlements, ensure quality of the food grains distributed through the TPDS, distribution of wheat flour in packed condition instead of wheat through the Fair Price Shops are recommended to address the shortcomings and weaknesses of the TPDS vis-avis the tribal population in Kerala.

Characterization of Wastes from Natural Rubber and Rubber Wood Processing Industries and Their Utilization for Biomethanation

The research work which was carried out to characterization of wastes from natural rubber and rubber wood processing industries and their utilization for biomethanation. Environmental contamination is an inevitable consequence of human activity. The liquid and solid wastes from natural rubber based industries were: characterized and their use for the production of biogas investigated with a view to conserve conventional energy, and to mitigate environmental degradation.Rubber tree (flevea brasiliensis Muell. Arg.), is the most important commercial source of natural rubber and in india. Recently, pollution from the rubber processing factories has become very serious due to the introduction of modern methods and centralized group processing practices.The possibility of the use of spent slurry as organic manure is discussed.l0 percent level of PSD, the activity of cellulolytic, acid producing,proteolytic, lipolytic and methanogenic bacteria were more in the middle stage of methanogenesis.the liquid wastes from rubber processing used as diluents in combination with PSD, SPE promoted more biogas production with high methane content in the gas.The factors that favour methane production like TS, VS, cellulose and hemicellulose degradation were favoured in this treatment which led to higher methane biogenesis.The results further highlight ways and means to use agricultural wastes as alternative sources of energy.

GABAA and GABAI Receptor Subunits Gene Expression and their Functional Role in Pilocarpine Induced Temporal Lobe Epilepsy

The research work which was carried out to characterization of wastes from natural rubber and rubber wood processing industries and their utilization for biomethanation. Environmental contamination is an inevitable consequence of human activity. The liquid and solid wastes from natural rubber based industries were: characterized and their use for the production of biogas investigated with a view to conserve conventional energy, and to mitigate environmental degradation.Rubber tree (flevea brasiliensis Muell. Arg.), is the most important commercial source of natural rubber and in india. Recently, pollution from the rubber processing factories has become very serious due to the introduction of modern methods and centralized group processing practices.The possibility of the use of spent slurry as organic manure is discussed.l0 percent level of PSD, the activity of cellulolytic, acid producing,proteolytic, lipolytic and methanogenic bacteria were more in the middle stage of methanogenesis.the liquid wastes from rubber processing used as diluents in combination with PSD, SPE promoted more biogas production with high methane content in the gas.The factors that favour methane production like TS, VS, cellulose and hemicellulose degradation were favoured in this treatment which led to higher methane biogenesis.The results further highlight ways and means to use agricultural wastes as alternative sources of energy.

Biochemical and Biotechnological investigations on the water-fern Salvinia molesta Mitchell

The present work is focussed mainly on the utilization of this weed-biomass on a biochemical and biotechnological basis. Before designing scientific and systematic utilization of any given biomass, the detailed analysis of its chemical componets is essential. Hence, as the preliminary part of the experimental works, samples of Salvinia were analysed for its chemical constituents.Before designing scientific and systematic utilization of any given biomass, the detailed analysis of its chemical componets is essential .The composition of the substrate contributes much to the nutritive value of mushrooms. Hence, alterations in the nutritive value of mushrooms (in terms of total carbohydrates, proteins, lipids and minerals) in response to Salvinia as substrate were analyzed.Substrate after mushroom harvest (spent substrate) can be utilized for various purposes such as cattle feed, as a source of degradative enzymes, as a substrate for other mushrooms and as garden manure. But studies are limited with regard to the utilization of Pleurotus spent substrate as garden manure. So the value of spent substrate as an organic supplement and its multidimensional impacts on soil chemical status, soil microbial population dynamics and plant growth (Amhurium andreanum) were carried out.Major findings of this work have got much relevance in designing measures to utilize different types of plant biomass, especially aquatic weeds, with the aid of a powerful biological tool, the lignocellulolytic fungus, Pleurorus

Structural, electrical and electrochemical characterization of high frequency magnetron sputtered spinel oxide cathode films for lithium ion battery applications

The main challenges in the deposition of cathode materials in thin film form are the reproduction of stoichiometry close to the bulk material and attaining higher rates of deposition and excellent crystallinity at comparatively lower annealing temperatures. There are several methods available to develop stoichiometric thin film cathode materials including pulsed laser deposition; plasma enhanced chemical vapor deposition, electron beam evaporation, electrostatic spray deposition and RF magnetron sputtering. Among them the most versatile method is the sputtering technique, owing to its suitability for micro-fabricating the thin film batteries directly on chips in any shape or size, and on flexible substrates, with good capacity and cycle life. The main drawback of the conventional sputtering technique using RF frequency of 13.56MHz is its lower rate of deposition, compared to other deposition techniques A typical cathode layer for a thin film battery requires a thickness around one micron. To deposit such thick layers using convention RF sputtering, longer time of deposition is required, since the deposition rate is very low, which is typically 10-20 Å/min. This makes the conventional RF sputtering technique a less viable option for mass production in an economical way. There exists a host of theoretical and experimental evidences and results that higher excitation frequency can be efficiently used to deposit good quality films at higher deposition rates with glow discharge plasma. The effect of frequencies higher than the conventional one (13.56MHz) on the RF magnetron sputtering process has not been subjected to detailed investigations. Attempts have been made in the present work, to sputter deposit spinel oxide cathode films, using high frequency RF excitation source. Most importantly, the major challenge faced by the thin film battery based on the LiMn2O4 cathode material is the poor capacity retention during charge discharge cycling. The major causes for the capacity fading reported in LiMn2O4cathode materials are due to, Jahn-Teller distortion, Mn2+ dissolution into the electrolyte and oxygen loss in cathode material during cycling. The work discussed in this thesis is an attempt on overcoming the above said challenges and developing a high capacity thin film cathode material.

”Studies on Selected conducting polymers for Microwave and Electrical Applications

The electrical properties of polymers make up an inherently interdisciplinary topic, being closely associated, on the one hand, with the mechanical properties of polymers polarization and relaxation) and, on the other hand, with the semi conductive properties (conduction and break down). In addition, unlike conventional technologies, which use these properties in its various applications like antistatic coatings, rechargeable batteries, sensors, electrochromic devices, electrochemical devices etc, microwave technology extract the microwave absorbing ability of electrically conducting polymers. The conducting polymers are widely used in its potential applications like electro magnetic interference shielding, satellite communication links, beam steering radars, frequency selective surfaces etc. Considering the relevance of microwave applications of conducting polymers, the study of microwave properties of conducting polymers stands poised to become a compelling choice for synthetic chemists and condensed - matter physicists, physical chemists and material scientists, electrochemists and polymer scientists. The main aim of the present work is to study the microwave and low frequency properties of various conducting polymers, conducting semi-interpenetrating networks, conducting copolymers and to characterise it. Also this thesis collated the microwave properties of these conducting systems and exposes the various technologically important applications in the industrial, scientific, communication and defence applications.

Studies On The Electrical Properties Of Some Crystalline Organic Compounds And Conducting Polymers

Solid electrolytes for applications like chemical sensing, energy storage, and conversion have been actively investigated and developed since the early sixties. Although of immense potential, solid state protonic conductors have been ignored in comparison with the great interest that has been shown to other ionic conductors like lithium and silver ion conductors. The non-availability of good, stable protonic conductors could be partly the reason for this situation. Although organic solids are better known for their electrical insulating character, ionic conductors of organic origin constitute a recent addition to the class of ionic conductors. However, detailed studies (N1 such conductors are scarce. Also the last decade has witnessed an unprecedented boom in research on organic "conducting polymers". These newly devised materials show conductivity spanning from insulator to metallic regimes, which can be manipulated by appropriate chemical treatment. They find applications in devices ranging from rechargeable batteries to "smart windows". This thesis mainly deals with the synthesis and investigations on the electrical properties of (i) certain organbc protonic conductors derived from ethylenediamine and (ii) substituted polyanilines

Evaluation of the Power Consumption of Routing Protocols for Wireless Sensor Networks

Sensor networks are one of the fastest growing areas in broad of a packet is in transit at any one time. In GBR, each node in the network can look at itsneighbors wireless ad hoc networking (? Eld. A sensor node, typically'hop count (depth) and use this to decide which node to forward contains signal-processing circuits, micro-controllers and a the packet on to. If the nodes' power level drops below a wireless transmitter/receiver antenna. Energy saving is one certain level it will increase the depth to discourage trafiE of the critical issue for sensor networks since most sensors are equipped with non-rechargeable batteries that have limitedlifetime. Routing schemes are used to transfer data collectedby sensor nodes to base stations. In the literature many routing protocols for wireless sensor networks are suggested. In this work, four routing protocols for wireless sensor networks viz Flooding, Gossiping, GBR and LEACH have been simulated using TinyOS and their power consumption is studied using PowerTOSSIM. A realization of these protocols has beencarried out using Mica2 Motes.

Activated packed bed bioreactor for rapid nitrification in brackish water hatchery systems

A packed bed bioreactor (PBBR) was developed for rapid establishment of nitrification in brackish water hatchery systems in the tropics. The reactors were activated by immobilizing ammonia-oxidizing (AMONPCU- 1) and nitrite-oxidizing (NIONPCU-1) bacterial consortia on polystyrene and low-density polyethylene beads, respectively. Fluorescence in situ hybridization demonstrated the presence of autotrophic nitrifiers belong to Nitrosococcus mobilis, lineage of b ammonia oxidizers and nitrite oxidizer Nitrobacter sp. in the consortia. The activated reactors upon integration to the hatchery system resulted in significant ammonia removal (P\0.01) culminating to its undetectable levels. Consequently, a significantly higher percent survival of larvae was observed in the larval production systems. With spent water the reactors could establish nitrification with high percentage removal of ammonia (78%), nitrite (79%) and BOD (56%) within 7 days of initiation of the process. PBBR is configured in such a way to minimize the energy requirements for continuous operation by limiting the energy inputs to a single stage pumping of water and aeration to the aeration cells. The PBBR shall enable hatchery systems to operate under closed recirculating mode and pave the way for better water management in the aquaculture industry.

Synthesis, Characterization and Catalytic Activity of Nanocrystalline Ceria Modified With Zirconia

The use of catalysts in chemical and refining processes has increased rapidly since 1945, when oil began to replace coal as the most important industrial raw material. Catalysis has a major impact on the quality of human life as well as economic development. The demand for catalysts is still increasing since catalysis is looked up as a solution to eliminate or replace polluting processes. Metal oxides represent one of the most important and widely employed classes of solid catalysts. Much effort has been spent in the preparation, characterization and application of metal oxides. Recently, great interest has been devoted to the cerium dioxide (CeO2) containing materials due to their broad range of applications in various fields, ranging from catalysis to ceramics, fuel cell technologies, gas sensors, solid state electrolytes, ceramic biomaterials, etc., in addition to the classical application of CeO2 as an additive in the so-called three way catalysts (TWC) for automotive exhaust treatment. Moreover, it can promote water gas shift and steam reforming reactions, favours catalytic activity at the interfacial metal-support sites. The solid solutions of ceria with Group IV transitional-metals deserve particular attention for their applicability in various technologically important catalytic processes. Mesoporous CeO2−ZrO2 solid solutions have been reported to be employed in various reactions which include CO oxidation, soot oxidation, water-gas shift reaction, and so on. Inspired by the unique and promising characteristics of ceria based mixed oxides and solid solutions for various applications, we have selected ceria-zirconia oxides for our studies. The focus of the work is the synthesis and investigation of the structural and catalytic properties of modified and pure ceria-zirconia mixed oxide.

Evaluation of the Power Consumption of Routing Protocols for Wireless Sensor Networks

Sensor networks are one of the fastest growing areas in broad of a packet is in transit at any one time. In GBR, each node in the network can look at itsneighbors wireless ad hoc networking (? Eld. A sensor node, typically'hop count (depth) and use this to decide which node to forward contains signal-processing circuits, micro-controllers and a the packet on to. If the nodes' power level drops below a wireless transmitter/receiver antenna. Energy saving is one certain level it will increase the depth to discourage trafiE of the critical issue forfor sensor networks since most sensors are equipped with non-rechargeable batteries that have limited lifetime.

Evaluation of the Power Consumption of Routing Protocols for Wireless Sensor Networks

Sensor networks are one of the fastest growing areas in broadwireless ad hoc networking (?Eld. A sensor node, typically'contains signal-processing circuits, micro-controllers and awireless transmitter/receiver antenna. Energy saving is oneof the critical issue for sensor networks since most sensorsare equipped with non-rechargeable batteries that have limited lifetime.In thiswork, four routing protocols for wireless sensor networks vizFlooding, Gossiping, GBR and LEACH have been simulated using Tiny OS and their power consumption is studied usingcaorwreiredTOoSuStIuMs.ingAMirceaal2izMaotitoens.of these protocols has been carried out using mica 2 motes

Economic Impact of Identity Theft in India: Lessons from Western Countries

In this computerized, globalised and internet world our computer collects various types of information’s about every human being and stores them in files secreted deep on its hard drive. Files like cache, browser history and other temporary Internet files can be used to store sensitive information like logins and passwords, names addresses, and even credit card numbers. Now, a hacker can get at this information by wrong means and share with someone else or can install some nasty software on your computer that will extract your sensitive and secret information. Identity Theft posses a very serious problem to everyone today. If you have a driver’s license, a bank account, a computer, ration card number, PAN card number, ATM card or simply a social security number you are more than at risk, you are a target. Whether you are new to the idea of ID Theft, or you have some unanswered questions, we’ve compiled a quick refresher list below that should bring you up to speed. Identity theft is a term used to refer to fraud that involves pretending to be someone else in order to steal money or get other benefits. Identity theft is a serious crime, which is increasing at tremendous rate all over the world after the Internet evolution. There is widespread agreement that identity theft causes financial damage to consumers, lending institutions, retail establishments, and the economy as a whole. Surprisingly, there is little good public information available about the scope of the crime and the actual damages it inflicts. Accounts of identity theft in recent mass media and in film or literature have centered on the exploits of 'hackers' - variously lauded or reviled - who are depicted as cleverly subverting corporate firewalls or other data protection defenses to gain unauthorized access to credit card details, personnel records and other information. Reality is more complicated, with electronic identity fraud taking a range of forms. The impact of those forms is not necessarily quantifiable as a financial loss; it can involve intangible damage to reputation, time spent dealing with disinformation and exclusion from particular services because a stolen name has been used improperly. Overall we can consider electronic networks as an enabler for identity theft, with the thief for example gaining information online for action offline and the basis for theft or other injury online. As Fisher pointed out "These new forms of hightech identity and securities fraud pose serious risks to investors and brokerage firms across the globe," I am a victim of identity theft. Being a victim of identity theft I felt the need for creating an awareness among the computer and internet users particularly youngsters in India. Nearly 70 per cent of Indian‘s population are living in villages. Government of India already started providing computer and internet facilities even to the remote villages through various rural development and rural upliftment programmes. Highly educated people, established companies, world famous financial institutions are becoming victim of identity theft. The question here is how vulnerable the illiterate and innocent rural people are if they suddenly exposed to a new device through which some one can extract and exploit their personal data without their knowledge? In this research work an attempt has been made to bring out the real problems associated with Identity theft in developed countries from an economist point of view.