Cement stabilised rammed earth. Part B: compressive strength and stress-strain characteristics

Strength and behaviour of cement stabilised rammed earth (CSRE) is a scantily explored area. The present study is focused on the strength and elastic properties of CSRE. Characteristics of CSRE are influenced by soil composition, density of rammed earth, cement and moisture content. The study is focused on examining (a) role of clay content of the soil on strength of CSRE and arriving at optimum clay fraction of the soil mix, (b) influence of moisture content, cement content and density on strength and (c) stress-strain relationships and elastic properties for CSRE. Major conclusions are (a) there is considerable difference between dry and wet compressive strength of CSRE and the wet to dry strength ratio depends upon the clay fraction of soil mix and cement content, (b) optimum clay fraction yielding maximum compressive strength for CSRE is about 16%, (c) strength of CSRE is highly sensitive to density and for a 20% increase in density the strength increases by 300-500% and (d) in dry state the ultimate strain at failure for CSRE is as high as 1.5%, which is unusual for brittle materials.

Solvent effect on the spectroscopic properties of 6MAMC and 7MAMC

The absorption and emission spectra of two dyes namely 6MAMC and 7MAMC have been recorded at room temperature in solvents of different polarities. The ground-state dipole moments (mu(g)) of these two were determined experimentally by Guggenheim method and were compared with theoretical values obtained using quantum chemical method. The exited state (mu(e))dipole moments were estimated from Lippert's, Bakhshiev's and Chamma-Viallet's equations by using the variation of the Stokes shift with the solvent dielectric constant and refractive index. The ground and excited-state dipole moments were calculated by means of the solvatochromic shift method and also the excited-state dipole moments are determined in combination with ground-state dipole moments. It was observed that dipole moments of excited state were higher than those of the ground state, indicating a substantial redistribution of the pi-electron densities in a more polar excited state for these two dyes. (C) 2010 Elsevier B.V. All rights reserved.

Partial Discharge Resistant Characteristics of Epoxy Nanocomposites

Epoxy nanocomposite samples with a good dispersion of alumina nanoparticles in epoxy matrix were prepared and experiments were performed to measure their partial discharge resistant characteristics. Epoxy alumina nanocomposites with 0.1, 1, 5, 10 and 15 wt% nanofillers were prepared in the laboratory and partial discharge (PD) experiments were conducted at a voltage of 10 kV for different durations using IEC (b) type electrodes. The degradation of the sample surfaces were analyzed using SEM techniques, surface profile studies, FTIR spectroscopy as well as PD studies. An attempt was made to understand the interaction dynamics between the nanoparticle and the epoxy chain by measuring the glass transition temperature of the nanocomposites. The partial discharge resistance obtained for the nanocomposites are compared with those of unfilled epoxy and epoxy microcomposites. It was observed that even with 0.1 wt% of nanofiller added to the epoxy matrix, the partial discharge resistance to degradation gets improved considerably. It was also observed that the inter particle distance has a significant effect on the discharge resistance to degradation. The improvement in the degradation resistance is attributed to the interactions between the nanoparticle and the epoxy chain. A possible mechanism for the surface degradation of nanocomposites has been proposed.

A quasi-steady performance prediction model for dynamic characteristics of a volute pump

A performance prediction model generally applicable for volute-type centrifugal pumps has been extended to predict the dynamic characteristics of a pump during its normal starting and stopping periods. Experiments have been conducted on a volute pump with different valve openings to study the dynamic behaviour of the pump during normal start-up and stopping, when a small length of discharge pipeline is connected to the discharge flange of the pump. Such experiments have also been conducted when the test pump was part of a hydraulic system, an experimental rig, where it is pumping against three similar pumps, known as supply pumps, connected in series, with the supply pumps kept idle or running. Instantaneous rotational speed, flowrate, and delivery and suction pressures of the pump were recorded and it was observed in all the tested cases that the change of pump behaviour during the transient period was quasi-steady, which validates the quasi-steady approach presented in this paper. The nature of variation of parameters during the transients has been discussed. The model-predicted dynamic head-capacity curves agree well with the experimental data for almost all the tested cases.

Brush plated CdSe films and their photoelectrochemical characteristics

The brush plating technique has been employed for the first time to obtain CdSe films on Ti and conducting glass substrates. These films have been annealed in an argon atmosphere and their structural, optical and photoelectrochemical properties are discussed. The power conversion efficiency has been found to be 7.43% under an illumination of 80 mW cm-2. A peak quantum efficiency of 0.64 is obtained for an incident wavelength of 720 nm. Donor concentration of 3.42 x 10(17) cm-3, electron mobility of 3 cm2 V-1 s-1 and minority carrier diffusion length of 0.013 mum have been obtained.

Calcium ionophore, A23187 and its amino acid complexes: spectroscopic and molecular modeling studies.

The circular dichroism, fluorescence, Nuclear Magnetic Resonance and BLM conductance studies indicate that A23187 forms a stable complex with amino acids at low ionophore concentrations (<10(-4)M). However, A23187 prefers to be in a dimeric structure with no significant binding to amino acids, at concentrations higher than 10(-4)M. It was also observed that at lower concentrations, at which the amino acids bind to the ionophore, the affinity for calcium ions was several orders of magnitude lower than that at higher ionophore concentrations. We have also conducted molecular modeling studies to examine the structure of the A23187 dimer and its amino acid complexes. The results of these modeling studies strongly support our experimental results and validate the formation of a hydrogen bonded and energetically stable A23187 dimer and its amino acid complexes.

Characteristics of superplasticity domain in the processing map for hot working of an Al alloy 2014---20vol.%Al2O3 metal matrix composite

The processing map for hot working of Al alloy 2014-20vol.%Al2O3 particulate-reinforced cast-plus-extruded composite material has been generated covering the temperature range 300-500 degrees C and the strain rate range 0.001-10 s(-1) based on the dynamic materials model. The efficiency eta of power dissipation given by 2m/(m + 1), where m is the strain rate sensitivity, is plotted as a function of temperature and strain rate to obtain a processing map. A domain of superplasticity has been identified, with a peak efficiency of 62% occurring at 500 degrees C and 0.001 s(-1). The characteristics of this domain have been studied with the help of microstructural evaluation and hot-ductility measurements. Microstructural instability is predicted at higher strain rates above (ls(-1)) and lower temperatures (less than 350 degrees C).

Charge-transfer interaction of picolines with iodine and pi-accepters- A spectroscopic study

The interaction of 2-amino-6-methylpyridine, 2-picoline and 4-picoline as donors with iodine, 7,7',8,8'-tetracyanoquinodimethane,2,3-dichloro-5,6-dicyano-1,4-benzoquinone, p-chloranil, o-chloranil, 2,4,7-trinitro-9-fluorenone and 2,4,5,7-tetranitro-9-fluorenone as acceptors has been studied by measuring visible and ultraviolet spectra. Infrared, electron paramagnetic and nuclear magnetic resonance spectra have also been obtained. Kinetic parameters have been derived. The results indicate that the charge transfer interaction occurs through the formation of free radicals which is followed by a slow reaction to give a diamagnetic product. However, with iodine, the charge transfer complex formation occurs without the formation of free radicals. The donor site is inferred to be the lone pair of electrons of the amino nitrogen of 2-amino-6-methylpridine whereas for 2- and 4-picolines, the preferred site is lone pair of electrons on the pyridine nitrogen.

Hot-working characteristics of Zircaloy-2 in the temperature range of 650–950°C

The hot-working characteristics of Zircaloy-2 have been studied in the temperature range of 650 to 950°C and in the strain-rate range of 10−3 to 102 s−1 using power dissipation maps which describe the variation of the efficiency of power dissipation, η = 2m /(m + 1) where m is the strain-rate sensitivity of flow stress. The individual domains exhibited by the map have been interpreted and validated by detailed metallographic investigations. Dynamic recrystallization occurs in the temperature range of 730 to 830°C and in the strain-rate range of 10−2 to 2 s−1. The peak efficiency occurs at 800°C and 0.1 s−1 which may be considered as the optimum hot-working parameters in the α-phase field of Zircaloy-2. Superplastic behaviour, characterized by a high efficiency of power dissipation is observed at temperatures greater than 860°C and at strain rates lower than 10−2 s−1. When deformed at 650°C and 10−3 s−1, the primary restoration mechanism is dynamic recovery, while at rates higher than 2s−1, the material exhibits microstructural instabilities in the form of localized shear bands.

Hot deformation characteristics of INCONEL alloy MA 754 and development of a processing map

The characteristics of hot deformation of INCONEL alloy MA 754 have been studied processing maps obtained on the basis of flow stress data generated in compression in the temperature range 700-degrees-C to 1150-degrees-C and strain rate range 0.001 to 100 s-1. The map exhibited three domains. (1) A domain of dynamic recovery occurs in the temperature range 800-degrees-C to 1075-degrees-C and strain rate range 0.02 to 2 s-1, with a peak efficiency of 18 pct occurring at 950-degrees-C and 0.1 s-1. Transmission electron microscope (TEM) micrographs revealed stable subgrain structure in this domain with the subgrain size increasing exponentially with an increase in temperature. (2) A domain exhibiting grain boundary cracking occurs at temperatures lower than 800-degrees-C and strain rates lower than 0.01 s-1. (3) A domain exhibiting intense grain boundary cavitation occurs at temperatures higher than 1075-degrees-C. The material did not exhibit a dynamic recrystallization (DRX) domain, unlike other superalloys. At strain rates higher than about 1 s-1, the material exhibits flow instabilities manifesting as kinking of the elongated grains and adiabatic shear bands. The material may be safely worked in the domain of dynamic recovery but can only be statically recrystallized.

Spectroscopic Studies on Silver Selenide Thin Films

Silver selenide thin films of thickness between 80 nm and 160 nm were prepared by thermal evaporation technique at a high vacuum better than 2x10(-5)mbar on well cleaned glass substrates at a deposition rate of 0.2 nm/sec. Silver selenide thin films were polycrystalline with orthorhombic structure. Ellipsometric spectra of silver selenide thin films have been recorded in the wavelength range between 300 nm and 700 nm. Optical constants like refractive index, extinction coefficient, absorption coefficient, and optical band gap of silver selenide thin film have been calculated from the recorded spectra. The refractive index of silver selenide has been found to vary between 1.9 and 3.2 and the extinction coefficient varies from 0.5 to 1.6 with respect to their corresponding thickness of the films. Transmittance spectra of these films have been recorded in the wavelength range between 300 nm and 900 nm and its spectral data are analysed. The photoluminescence studies have been carried out on silver selenide thin films and the strong emission peak is found around 1.7 eV. The calculated optical band of thermally evaporated silver selenide thin films is found to be around 1.7 eV from their Ellipsometric, UV-Visible and Photoluminescence spectroscopic studies.

Observation of asymmetry in U�I characteristics of contacts of the form metal 1�superconductor�metal 2

During experiments carried out to find out a suitable contact metal for electronic components based on high-T(c) superconductor films (Y-Ba-Cu-O), it is observed that there is an asymmetry in the U-I characteristics if the two contacts are made of different metals. The asymmetry is more pronounced if one of the contact metals is aluminium. The asymmetry is lowest if one of the contact metals is silver and the other gold.

Organometallic chemistry of diphosphazanes. Part IX: Syntheses and spectroscopic studies of molybdenum and tungsten tetracarbonyl complexes of unsymmetrical diphosphazanes

The unsymmetrical diphosphazanes X2PN(Pr(i))PYY'(1a-1h) {X = Ph, YY' = O2 C6H4 (1a) or YY' = O2C12H8 (1b); X = Ph, Y = Ph, Y' = OC6H4Me-4 (1c), OC6H4Br-4 (1d), OC6H3Me2-3,5 (1e), OC5H4N-2 (1f), N2C3HMe2-3,5 (1g) or Cl (1h)} react with [M(CO)4(NHC5H10)2] (M = Mo, W) to yield the cis-chelate complexes [M(CO)4{X2PN(Pr(i)) PYY'}] {M = Mo (2a-2h); M = W (3-f,3-g)}. These complexes have been characterized by H-1, P-31 and C-13 NMR and IR spectroscopic studies.

Microwave assisted synthesis and UV-Vis spectroscopic studies of silver nanoparticles synthesized using vanillin as a reducing agent

The present investigation explores the adaptability of a microwave assisted route to obtain silver nanoparticles by the reduction of AgNO3 with vanillin, an environmentally benign material. Anionic surfactants such as AOT and SDS were used separately for encapsulating AgNPs and their role was compared. The UV-Visible absorption spectra present a broad SPR band consisting of two peaks suggesting the formation of silver nanoparticle with bimodal size distribution. The TEM image shows particles with spherical and hexagonal morphologies which confirms the results of UV-Vis studies. The anisotropy in the particle morphology can be attributed to the surface oxidation which in turn produces Ag@Ag2O core-shell nanostructures. Thus an intriguing feature of this system is that the obtained colloid is a mixture of AgNPs with and without Ag2O layers. Studies on the influence of pH on the stability of the synthesized nanoparticles revealed that the presence of excess Ag2O layers has a profound influence on it. Ag2O layers can be removed from AgNPs' surface by changing the solution pH to the acidic regime. The present study attests the enhanced ability of AOT in stabilizing the AgNPs in aqueous media. (C) 2011 Elsevier B.V. All rights reserved.