Transport properties of ionic liquid electrolytes with organic diluents

Ionic liquids (ILs) form a novel class of electrolytes with unique properties that make them attractive candidates for electrochemical devices. In the present study a range of electrolytes were prepared based on the IL N-methyl-N-propylpyrrolidinium bis(trifluoromethylsulfonyl) amide ([C₃mpyr][NTf₂]) and LiNTf2 salt. The traditional organic solvent diluents vinylene carbonate (VC), ethylene carbonate (EC), tetrahydrofuran (THF) and toluene were used as additives at two concentrations, 10 and 20 mol%, leading to a ratio of about 0.6 and 1.3 diluent molecules to lithium ions, respectively. Most promisingly, the lithium ions see the greatest effect in the presence of all the diluents, except toluene, producing a lithium self-diffusion coefficient of almost a factor of 2.5 times greater for THF at 20 mol%. Raman spectroscopy subtly indicates that THF may be effectively breaking up a small portion of the lithium ion–anion interaction. While comparing the measured molar conductivity to that calculated from the self-diffusion coefficients of the constituents indicates that the diluents cause an increase in the overall ion clustering. This study importantly highlights that selective ion transport enhancement is achievable in these materials.

Exploring corrosion protection of Mg via ionic liquid pretreatment

We present the development of a 10–100 nanometer thick surface film upon pure Mg on exposure to an ionic liquid (IL) based on the bis(trifluoromethanesulfonyl)amide (TFSA) anion. This film formation is the result of the oxidative reactivity of the metal in the IL, with the subsequent effect of ultimately protecting the underlying metal from corrosion in aqueous chloride containing solution. Film formation was studied in the IL using an electrochemical droplet cell. It was seen that this film is adherent and subsequently facilitates appreciable protection against corrosion as judged by subsequent electrochemical testing in the form of potentiodynamic polarization and impedance spectroscopy, along with direct observation. The physical film morphology was studied by electron microscopy and focused ion beam.

The zwitterion effect in ionic liquids : towards practical rechargeable lithium-metal batteries

Practical lithium-metal batteries are the ultimate goal of battery researchers. The addition of a zwitterionic compound (see Figure) to an ionic liquid electrolyte doped with a lithium salt results in a 100% enhancement of the current densities achieved in the cycling of a lithium-metal cell. This phenomenon arises due to increased lithium-ion mobility or a reduced solid electrolyte interphase layer resistance.

Ionic conductivity studies of polymeric electrolytes containing lithium salt with plasticizer

New plasticized polymer electrolytes were synthesized based on poly ethylene oxide (PEO), Poly (N,N-dimethylamino-ethyl-methacrylate) (PDMAEMA), LiN(CF₃SO₂)₂ (LITFSI) as the salt and tetraethylene glycol dimethyl ether(tetraglyme) and EC + PC as plasticizers. The preparation and characterization of the polymer electrolytes were investigated as a function of temperature and various concentrations of LITFSI. Impedance spectroscopy and differential scanning calorimeter (DSC) were used to characterize the effects of various temperature, lithium salt concentration and two plasticizers on conductivity. The complex of PDMAEMA/PEO/LiTFSI/tetraglyme (S2) exhibits higher conductivity (4.74 × 10⁻⁴ S cm⁻¹at 25 °C) than PDMAEMA/PEO/LiTFSI/EC + PC (S1).

Lithium-polymer battery based on an ionic liquid–polymer electrolyte composite for room temperature applications

A lithium-polymer battery based on an ionic liquid–polymer electrolyte (IL–PE) composite membrane operating at room temperature is described. Utilizing a polypyrrole coated LiV₃O₈ cathode material, the cell delivers >200 mAh g⁻¹ with respect to the mass of the cathode material. Discharge capacity is slightly higher than those observed for this cathode material in standard aprotic electrolytes; it is thought that this is the result of a lower solubility of the LiV₃O₈ material in the IL–PE composite membrane.

Purification or contamination? The effect of sorbents on ionic liquids

Commonly used for purification, alumina and silica are found to contaminate ionic liquids with particles; these particles cannot be removed easily and can have a non-negligible impact on the electrochemical, spectroscopic and physical properties of an ionic liquid, including its nucleation and crystallisation kinetics.

Dye-sensitized nanocrystalline solar cells incorporating ethylmethylimidazolium-based ionic liquid electrolytes

High-performance dye-sensitized solar cells incorporating electrochemically stable non-volatile electrolytes are especially desirable devices. In particular, ionic liquid systems based on ethylmethylimidazolium dicyanamide seem to be promising for this purpose. These have triggered our interest in the properties of further ethylmethylimidazolium-based ionic liquids with anions which are close relatives of dicyanamide. In this study, the effect of three different anions, tricyanomethanide, dicyanamide and thiocyanate, on the performance of dye-sensitized solar cells have been investigated. Both the short circuit photocurrent and conversion efficiency are increased with decreasing viscosity of the ionic liquids under comparable conditions. A conversion efficiency of 2.1% at 30% light intensity was observed for the cell containing the tricyanomethanide salt, which has lowest viscosity among the three ionic liquids, while efficiencies of 0.7% and 1.7% at the same light intensity were observed in the case of dicyanamide and thiocyanate salts, respectively, as an electrolyte.

Structural characterization of novel ionic salts incorporating trihalide anions

The crystal structures of several low-melting salts containing trihalide ions, namely 1-ethyl-3-methylimidazolium tribromide ([C₂mim][Br3]), 1-ethyl-1-methylpyrrolidinium tribromide ([C₂mpyr][Br₃]), and 1-propyl-1-methylpyrrolidinium triiodide ([C₃mpyr][I₃]), are reported for the first time. Thermal analysis reveals that the tribromide salts are lower-melting than their monohalide analogues. Analysis of the crystal structures allows examination of the influence of the anions on the physical properties of the salts.

Use of ionic liquids as electrolytes in electromechanical actuator systems based on inherently conducting polymers

The use of ionic liquids (ILs) as electrolytes for electromechanical actuators based on polypyrroles (PPy's) is described. The composition of the electrolytes has a significant effect on the electrochemical properties of the PPy actuator and subsequently on actuator performance, improving cycle life and strain generated. The actuator performance in ionic liquid electrolytes is significantly better than that in traditional organic and aqueous electrolytes.

Structural characterization of novel ionic materials incorporating the bis(trifluoromethanesulfonyl)amide anion

A range of low melting salts of the bis(trifluoromethanesulfonyl)amide (TFSA) anion with hindered organic cations (N-methyl-1-methylpyrrolinium, N,N-dimethylpyrrolidinium, N,N,N,-trimethylammonium, and N,N,N,N-tetrakis(n-propyl)ammonium) have been crystallized. Single-crystal X-ray diffraction data show these materials to consist of discrete ions with only weak C−H···O (or for Me₃NH N−H···O) contacts between the constituent atoms of the cations and anions close to the limits of van der Waals separations. Consequently, the observed physical properties of these materials presumably result from the diffuse negative charge on the TFSA anion and inefficient packing of these large and irregularly shaped ions.

NMR determination of ionic structure in plasticized polyether-urethane polymer electrolytes

Solid polymer electrolytes based on amorphous polyether-urethane networks combined with lithium or sodium salts and a low molecular weight cosolvent (plasticizer) have been investigated in our laboratories for several years. Conductivity enhancements of up to two orders of magnitude can be obtained whilst still retaining solid elastomeric properties. In order to understand the effects of the plasticizers and their mechanism of conductivity enhancement, multinuclear NMR has been employed to investigate ionic structure in polymer electrolyte systems containing NaCF₃SO₃, LiCF₃SO₃ and LiClO₃ salts.

With increasing dimethyl formamide (DMF) and propylene carbonate (PC) concentration the increasing cation chemical shift with fixed salt concentration indicates a decreasing anion-cation association consistent with an increased number of charge carriers. ¹³C chemical shift data for the same systems suggests that whilst DMF also decreases cation-polymer interactions, PC does the opposite, presumably by shielding cation-anion interactions. Temperature dependent ⁷Li spin-lattice relaxation times indicate the expected increase in ionic mobility upon plasticization with a shift of the T₁ minimum to lower temperatures. The magnitude of T₁ at the minimum increases upon addition of DMF whereas there is a slight decrease when PC is added. This also supports the suggestion that the DMF preferentially solvates the cation whereas the action of PC is limited to coulomb screening, hence freeing the anion.

A potential novel rapid screening NMR approach to boundary film formation at solid interfaces in contact with ionic liquids

The boundary films generated on a series of inorganic compounds, typical of native films on metal and ceramic surfaces, when exposed to various ionic liquids (ILs) based on the trihexyl(tetradecyl)phosphonium cation have been characterized using multinuclear solid-state NMR. The NMR results indicate that SiO₂ and Mg(OH)₂ interact strongly with the anion and cation of each IL through a mechanism of adsorption of the anion and subsequent close proximity of the cation in a surface double layer (as observed through ¹H−²⁹Si cross polarization experiments). In contrast, Al₂O₃, MgO, ZnO, and ZrO₂ appear less active, strongly suggesting the necessity of hydroxylated surface groups in order to enhance the generation of these interfacial films. Using solid-state NMR to characterize such interfaces not only has the potential to elucidate mechanisms of wear resistance and corrosion protection via ILs, but is also likely to allow their rapid screening for such durability applications.

An nmr investigation of ionic structure and mobility in plasticized solid polymer electrolytes

²³Na and ¹⁹F nuclear magnetic resonance spectroscopy is used to investigate the effect of plasticizer addition on ionic structure and mobility in a urethane crosslinked polyether solid polymer electrolyte. The incorporation of dimethyl formamide and propylene carbonate plasticizers in a sodium triflate/polyether system results in an upfield chemical shift for the ²³Na resonance consistent with decreased anion-cation association and increased cation-plasticizer interactions. The ¹⁹F resonances appears less susceptible to changes in chemical environment with only minor chemical shift changes recorded. Spin lattice relaxation measurements for the ¹⁹F nucleus are also reported. Two minima are observed in the relaxation measurements consistent with both an inter and intramolecular relaxation mechanism.