Crescimeno de apatita na superfície da liga Ti-7, 5Mo empregando tratamento higrotérmico

The objective of the present work was to evaluate surface of experimental alloy Ti-7.5Mo after hydrothermal treatment. Ingots were obtained in arc melting furnace under an argon atmosphere and then homogenized under vacuum at 1100ºC for 86.4 ks to eliminate chemical segregation and after cold worked discs were cutting and grinding. For surface treatment, samples were immersed in a container with NaOH aqueous solution 5M, autoclaved, washed with distilled water. Followed, samples were heat treated and they were soaking in 5xSBF to form an apatite layer on the surface. Surfaces were investigated by, scanning electron microscopy, X-Rays powder diffraction, atomic force microscopy and contact angle, in order to evaluate the wettability of the alloy surface. The results were compared with our previous studies using the group of chemical surface treatments and results shows better condition is 120 minutes in the autoclave

Uso de composto de poda de árvore e lodo de esgoto como substratos na formação de mudas de sangra d'água (Croton urucurana Baill.) irrigadas com três lâminas de água

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Estudo sobre o funcionamento de sistema de controle de tração em veículos automotores

This study explores the subject of traction control systems through bibliografy review on the spot of Mechanical Engineering. This paper has the objetivo of high light the main components and tecnology involved since MaxTrac system in 1971. It describes systems controled by throttle valve and breaks. Additionally, it i also presented basic knowlodged regarding electronic control unit and wheel sensors

Análise de fadiga em rodas automotivas utilizando método dos elementos finitos

The increasing search for better performance at the automotive industry, especially on the matter of fuel consumption, caused a progressive evolution of industrial technology. For the wheel this study is based on the try of reducing mass and decreasing the moment of inertia, characteristics that directly reflect on the performance parameter, as consumption and acceleration, so that it also is effective on the growth of the profit margin, since it reduces the costs of the locomotion. In this paper will be applied the Finite Element Analysis to explain the wheel behavior and identify ways to improve the performance. To the analyze it will be simulated a test condition established by ABNT NBR 6751:2009 foreseeing a possible collapse through general yielding and fatigue. The load here presented results from the equation presented on the norms and in the datas provided by the manufacturer

Determinação de chumbo em tubos de raios catódicos e em solo contaminado por espectrometria de absorção atômica

Pós-graduação em Ciência dos Materiais - FEIS

A influência da temperatura na secagem forçada da matéria-prima cerâmica da Formação Corumbataí na região do Polo de Santa Gertrudes (SP)

Pós-graduação em Geociências e Meio Ambiente - IGCE

Análise estrutural do suporte de pastilha de grafite para lubrificação de roda ferroviária

This study aims to structurally evaluate a support of graphite pastille for the lubrication of railway wheels. The proper lubrication of wheel flanges of the railway extends the life of this component, so it is very important that this occurs lubrication to reduce the costs involved in railway maintenance. To prepar the evaluation structural will be used to International Electrotechnical Comission standard (IEC 61373) establishing which load cases should be applied to this component. The applied loads on the support (accordance with IEC) are random accelerations and accelerations due to shocks, thus simulating the conditions that exist along the route of the train. The structural analyzes are performed by the finite element method, with the aid of the Cosmos software. Thus, it is possible to determine the stresses acting on the support, and so the allowable stresses compared with the standard proposed by the AISC. The stress in the structural analyzes are lower than allowable therefore considered for the configuration presented, unexpected structural problems

Procedência da cocaína e maconha definida por isótopos estáveis

Objectives: the aim of this work was to define the range of possible values for each isotope of carbon-13 and nitrogen-15 for cocaine and marijuana seized in Botucatu-SP, with the intention of distinguishing the geographical origin of the drug. Materials and Methods: samples of marijuana and cocaine were collected at the time of incineration. Then, at the Stable Isotope Center from São Paulo State University in Botucatu, São Paulo, Brazil, samples of marijuana were subjected to the drying process and subsequent grinding. Samples of cocaine were not submitted to the processes of drying and grinding because they were already in adequate granulometry. Subsequently, the samples of both drugs were weighed in accordance with the standards for carbon-13 and nitrogen-15. Lastly, CO2 and N2 gases were obtained from the samples through the elemental analyzer. They were then analyzed in a mass spectrometer to obtain values of δ13C and δ15N in ‰. Results and Discussion: the results of marijuana allowed for comparison with regions of Queensland, Australia, according to the range of δ13C between -29.9 ‰ and -29.3 ‰ and δ15N range from 4.1 ‰ to 5.8 ‰. The results were also consistent with those of the state of Pará, Brazil, where the values of δ13C and δ15N were -30.3 ± 0.7 ‰ and 5.0 ± 1.3 ‰, respectively. Also the results were in accordance with those from the state of Mato Grosso do Sul, Brazil, in which δ13C values varied by -28.7 ± 1.3 ‰, and δ15N values varied by 6.6 ± 1.1 ‰, respectively. In both regions, the samples identified as being from Pará and Mato Grosso do Sul showed an overlap. In addition, the results fitted with data from the state of Maranhão, in which the values of δ13C and δ15 N were -28.8 ± 1.6 ‰ and 2.9 ± 2.5 ‰, respectively. In the case of cocaine, the present study could not be related to the results from the literature. One possible explanation may be related to the non-purification of ...

Utilização da cinza de folha de cana-de-açúcar como material pozolânico em matrizes cimentantes

Pós-graduação em Engenharia Civil - FEIS

Tarefas de triangulação com restrições perceptuais em pessoas com deficiência auditiva: um estudo por meio de gps

This study aimed to investigate how people with hearing disability perform tasks of distances estimation for locomotion and navigation when deprived of effective perceptual and proprioceptive information. For this, participants with hearing disability went three distances being the first and second 100 meters and the third 140 meters (triangulation) from a source point in an inverted L open field trajectory and then returned to the origin, and the first two were driven by a researcher guide with adapted GPS coordinates of the study, and the third being three free-form sessions, the first one without any perceptual and proprioceptive restriction, the second without visual perception, and the third on the wheel-chair, that is, without proprioception. The results showed that people with hearing disability without the knowledge of the path do not possess satisfactory accuracy but when they learn the way even with the restriction of visual perception and proprioception they can return to the starting point in a task of triangulation. The "t" students test with a significance level of 5% (2.131) indicates significant differences between the first task without any perceptual restriction and the third where they performed in the wheelchair. To achieve these results we used remote monitoring via GPS and the TrackMaker software.

Características clínicas da associação entre o bruxismo do sono e o refluxo gastroesofágico merecem atenção profissional

Introduction: Bruxism has been defined as an oral parafunctional activity that includes clenching and/or grinding the teeth while asleep or awake. In addition to sleep bruxism (SB), various other orofacial movements sporadically occur during sleep. Occasional regurgitation and heartburn due to gastroesophageal reflux (GER) are frequent in the general population. GER refers to the presence of symptoms that are secondary to the reflux of gastric content through the esophagus with or without signs of esophageal mucosal lesions. Dentists are often the first health care professionals to diagnose GER through observation of its oral manifestation. Objective: The aim of the present case reports was to discuss the diagnosis and clinical procedures followed in two patients with SB and GER, thereby contributing to the dissemination of knowledge about these two entities. We therefore recommend dentists to be alert to identifying the first signs of GER that appear in the oral cavity. Conclusion: At this point, we highlight the importance of treating the patient as a whole, in an endeavor to identify other sources of the problems that could contribute as factors aggravating these conditions.

Effect of surface and heat treatments on the biaxial flexural strength and phase transformation of a Y-TZP ceramic

To evaluate the effect of grinding and airborne-particle abrasion on the biaxial flexural strength (BFS) and phase transformation of a Y-TZP ceramic, and examine whether sintering the veneering porcelain renders the previous heat treatment recommended by the manufacturer unnecessary. Materials and Methods: Lava zirconia specimens (N = 108) were obtained with the following dimensions: 14.0 mm diameter × 1.3 mm thickness (n = 36) and 14.0 mm × 1.6 mm (n = 72). The thicker specimens were ground with diamond burs under irrigation and received (heat-treated groups) or not (non-heat-treated groups) a heat treatment (1000°C for 30 min) prior to the four firing cycles applied to simulate the sintering of the veneering porcelain. All specimens were air abraded as follows (n = 12): 1) 30-μm silica-modified Al2O3 particles (Rocatec Soft); 2) 110-μm silica-modified Al2O3 particles (Rocatec Plus); and 3) 120-μm Al2O3 particles, followed by Rocatec Plus. Three specimens of each group were analyzed by x-ray diffraction (XRD) to assess the monoclinic phase content (%). The BFS test was performed in a mechanical testing machine (Instron 8874). Data (MPa) were analyzed by two-way ANOVA (grinding × airborne-particle abrasion and heat treatment × airborne-particle abrasion) and Tukey's post-hoc test (α = 0.05). The strength reliability was analyzed using the Weibull distribution. Results: Grinding significantly decreased the BFS of the non-heat-treated groups (p < 0.01). Within the ground groups, the previous heat treatment did not influence the BFS (p > 0.05). Air abrasion only influenced the BFS of the ground/heat-treated groups (p < 0.01). For the non-heat-treated groups, the grinding did not decrease the Weibull modulus (m), but it did decrease the characteristic strength (σ0). For Rocatec Soft and 120-μm Al2O3 particles + Rocatec Plus, the heat-treated groups presented lower m and higher σ0 than the ground/non-heat-treated groups. The independent variables did not seem to influence phase transformation. Air-abraded surfaces presented higher monoclinic zirconia content than the as-sintered and ground surfaces, which exhibited similar content. Conclusion: Even under irrigation, grinding compromised the Y-TZP ceramic strength. The sintering of the veneering porcelain rendered the previous heat treatment recommended by the manufacturer unnecessary. Airborneparticle abrasion influenced the strength of heat-treated zirconia.

Effect of surface and heat treatments on the biaxial flexural strength and phase transformation of a y-tzp ceramic

To evaluate the effect of grinding and airborne-particle abrasion on the biaxial flexural strength (BFS) and phase transformation of a Y-TZP ceramic, and examine whether sintering the veneering porcelain renders the previous heat treatment recommended by the manufacturer unnecessary. Materials and Methods: Lava zirconia specimens (N = 108) were obtained with the following dimensions: 14.0 mm diameter × 1.3 mm thickness (n = 36) and 14.0 mm × 1.6 mm (n = 72). The thicker specimens were ground with diamond burs under irrigation and received (heat-treated groups) or not (non-heat-treated groups) a heat treatment (1000°C for 30 min) prior to the four firing cycles applied to simulate the sintering of the veneering porcelain. All specimens were air abraded as follows (n = 12): 1) 30-μm silica-modified Al2O3 particles (Rocatec Soft); 2) 110-μm silica-modified Al2O3 particles (Rocatec Plus); and 3) 120-μm Al2O3 particles, followed by Rocatec Plus. Three specimens of each group were analyzed by x-ray diffraction (XRD) to assess the monoclinic phase content (%). The BFS test was performed in a mechanical testing machine (Instron 8874). Data (MPa) were analyzed by two-way ANOVA (grinding × airborne-particle abrasion and heat treatment × airborne-particle abrasion) and Tukey's post-hoc test (α = 0.05). The strength reliability was analyzed using the Weibull distribution. Results: Grinding significantly decreased the BFS of the non-heat-treated groups (p < 0.01). Within the ground groups, the previous heat treatment did not influence the BFS (p > 0.05). Air abrasion only influenced the BFS of the ground/heat-treated groups (p < 0.01). For the non-heat-treated groups, the grinding did not decrease the Weibull modulus (m), but it did decrease the characteristic strength (σ0). For Rocatec Soft and 120-μm Al2O3 particles + Rocatec Plus, the heat-treated groups presented lower m and higher σ0 than the ground/non-heat-treated groups. The independent variables did not seem to influence phase transformation. Air-abraded surfaces presented higher monoclinic zirconia content than the as-sintered and ground surfaces, which exhibited similar content. Conclusion: Even under irrigation, grinding compromised the Y-TZP ceramic strength. The sintering of the veneering porcelain rendered the previous heat treatment recommended by the manufacturer unnecessary. Airborneparticle abrasion influenced the strength of heat-treated zirconia.

Influência do tratamento superficial 3IP na vida em fadiga dos aços ABNT 4340 e 15-5PH para aplicação aeronáutica

Pós-graduação em Engenharia Mecânica - FEG

A roda em movimento e os movimentos da roda: refletindo sobre experiências

This article aims to narrate and analyze possibilities on aspects of the work developed by the group that composes the Mental Health and Public Health Improvement, using the Wheel Method, created by Gastão W. Campos, in different and diverse articulations and work organization spaces in psychosocial care field, such as Mental Health Forum, work groups related to Regional Collegiate Management (CGRs), with municipal teams to organize mental health network and with newcomer residents to a therapeutic residence It is from these different experiences that it is intended to reflect, discuss and promote a dialogue on the possibilities of the Wheel Method.