水溶性聚合物和两亲聚合物：聚（丙烯酰胺－co－丙烯酸钠）－g－聚（β－胺基丙酸）接枝共聚物

合成了端丙烯酰胺基聚（β－胺基两酸）大分子单体，用端基滴定法和１Ｈ—ＮＭＲ法测定了大分子单体的分子量，用１３Ｃ—ＮＭＲ和氢氧化钠水解法测定了支化度．在水溶液中用硫酸亚铁／异丙苯过氧化氢氧化还原引发体系引发丙烯酸胺、丙烯酸钠与聚（β－胺基丙酸）大分子单体的共聚反应，合成了聚（丙烯酰胺－ｃｏ－丙烯酸钠）－ｇ－聚（β－胺基丙酸）接枝共聚物．用１Ｈ—ＮＭＲ和滴定法测定了接枝共聚物的组成．溶液性质的数据表明，与部分水解聚丙烯酰胶相比，聚（β－胺基丙酸）含量较高的接枝共聚物具有较好的耐盐性和优异的贮存稳定性．

原子和离子的f~k与g~k的计算方法

本文给出了原子和离子能量表达式中的库仑积分与交换积分系数ｆｋ、ｇｋ的计算方法，同时给出了计算中所涉及的Ｒａｃａｈ系数、Ｕ（ｋ）、Ｖ（ｌｋ）和Ｃ（ｋ）‘矩阵等光谱参量的计算方法，用ＦＯＲＴＲＡＮｗ语言编写了关于ｆｋ和ｇｋ的计算机程序，只要输入与光谱项有关的量子数，即可迅速得到相应的ｋｆ、ｇｋ值，避免了烦琐的人工推算。

壳聚糖辐射效应的研究（Ⅰ）──辐照剂量与分子量的关系及辐射裂解的G（S）值

通过粘度的测量，考察了壳聚糖在不同条件下经不同剂量γ射线辐照所引起的分子量的变化，并分别计算了真空和空气中壳聚糖辐射裂解的Ｇ（Ｓ）值。

聚乙烯醇－g－聚丙烯酸膜用于渗透气化法分离乙醇－水的研究

合成了聚乙烯醇－ｇ－聚丙烯酸接枝聚合物（ＰＶＡ－ｇ－ＰＡＡ），分别用ＫＯＨ、ＮａＯＨ、ＬｉＣｌ的乙醇－水溶液处理ＰＶＡ－ｇ－ＰＡＡ膜。发现离子膜用于乙醇－水的渗透气化分离可以大幅度提高分离系数，特别是用ＫＯＨ处理，分离系数可达４００。

STRUCTURE OF AN ERBIUM COORDINATION COMPOUND WITH L-PROLINE, ([ER(PRO)2(H2O)5]CL3)(N)

catena-Poly[{pentaaqua(L-proline-O)-erbium-mu-(L-proline-O:O')} trichloride], {[Er(C5H9-NO2)2(H2O)5]Cl3}n, M(r) = 594.0, monoclinic, P2(1), a = 8.294 (1), b = 10.981 (3), c = 11.934 (3) angstrom, beta = 107.04 (2)degrees, V = 1039.2 (4) angstrom3, Z = 2, D(x) = 1.90 g cm-3, lambda(Mo Kalpha) = 0.71069 angstrom, mu = 45.2 cm-1, F(000) = 586, T = 298 K, R = 0.0244 for 1711 unique reflections [I > 3 sigma(I(o))]. The crystal consists of one-dimensional chains of infinite length in which one L-proline ligand bridges two neighboring Er ions, the other L-proline ligand being monodentate.

PE-MA对PE/CaCO_3增容作用的研究

本文通过加入接枝马来酸酐的聚乙烯(PE-MA),促进非报性的聚乙烯分子和带有极性表面的填料之间的互容。用扫描电子显微镜观察共混物低温脆断面上碳酸钙的分布表明,在加有增容剂PE-MA的PE/CaCO_3共混物中,CaCO_3颗粒大小均匀且分布也均匀,PE-MA明显起到了增容作用。综合结果指出,PE-MA的加入量占PE/CaCO_3/PE-MA总重量的5～10％时增容效果较好。力学性能测试表明,随PE-MA用量的增加,共混物的拉伸强度明显提高。断裂伸长率变化较小,熔融指数略有下降。

原子和离子的f~k与g~k的计算机解法

本文给出了原子和离子能量表达式中的库仑积分与交换积分系数f~k与g~k的计算方法,同时给出了计算中所涉及的Racah系数、U~(k)、V~(lk)和C~(k)矩阵等光谱参量的计算方法,我们用FORTRAN语言编写了关于f~k与g~k的计算机程序,只要输入与光谱项有关的量子数,即可迅速得到相应的f~k与g~k值,避免了烦琐的人工推算。

HIGH-TEMPERATURE SUPERCONDUCTOR, YBA2CU3O7-X AS ALL-SOLID-STATE LITHIUM CELL

The utility of the high-temperature superconductor, YBa2Cu3O7-x as the cathode material for an all-solid-state lithium cell has been examined. The capacity of YBa2Cu3O7-x is 223 mA h g-1 and the discharge efficiency is > 92%. Measurements of a.c. impedance show that the charge-transfer resistance at the interface of the electrolyte/cathode is very low and increases with the depth-of-discharge of the battery. Studies using X-ray photoelectron spectroscopy (XPS) reveal that the cathode becomes doped with Li+ ions as the cell discharges.

HDPE-g-PB接枝共聚物的合成及其与聚丁二烯的共混

利用~(60)Co辐照合成了HDPE与丁二烯的接枝共聚物,PE-g-PB。动态力学试验表明,它与PB较PE与PB有更好的相容性。PB含量相同时PB/PE-g-PB共混物比PB/PE共混物有较高的抗张强度和断裂伸长率。前者中两相分布较均匀,相区尺寸较小。

Cytoglobosins A-G, Cytochalasans from a Marine-Derived Endophytic Fungus, Chaetomium globosum QEN-14

Financial support from the Ministry of Science and Technology of China (2010CB833802 and 2007AA09Z446) and from the National Science Foundation of China (30910103914) is gratefully acknowledged.

Identification of 27 Porphyra lines (Rhodophyta) by DNA fingerprinting and molecular markers

Twenty-seven Porphyra lines, including lines widely used in China, wild lines and lines introduced to China from abroad in recent years, were screened by random amplified polymorphic DNA (RAPD) technique with 120 operon primers. From the generated RAPD products, 11 bands that showed stable and repeatable RAPD patterns amplified by OPC-04, OPJ-18 and OPX-06, respectively were scored and used to develop the DNA fingerprints of the 27 Porphyra lines. Moreover, the DNA fingerprinting patterns were converted into computer language expressed with two digitals, 1 and 0, which represented the presence (numbered as 1) or absence (numbered as 0) of the corresponding band, respectively. Based on the above results, computerized DNA fingerprints were constructed in which each of the 27 Porphyra lines has its unique fingerprinting pattern and can be easily distinguished from others. Software named PGI (Porphyra germplasm identification) was designed for identification of the 27 Porphyra lines. In addition, seven specific RAPD markers from seven Porphyra lines were identified and two of them were successfully converted into SCAR (sequence characterized amplification region) markers. The developed DNA fingerprinting and specific molecular markers provide useful ways for the identification, classification and resource protection of the Porphyra lines.

Comparative studies on the efficiency of energy transfer of two R-phycoerythrin-C-phycocyanin conjugates constructed from sodium periodate and glutaraldehyde respectively

The C-phycocyanin and the R-phycoerythrin were purified from the blue-green alga Spirulina platensis and red alga Polysiphonia urceolata respectively. Both sodium periodate and glutaraldehyde are effective coupling agents being capable of constructing the R-phycoerythrin-C-phycocyanin conjugate, which was also called phycobiliproteins energy transfer model. The two artificial conjugates constructed with different methods were purified by Sephadex G-200 chromatography respectively. Spectra analysis indicated that energy transfer occurred in the two conjugates. The conjugate with sodium periodate had the higher efficiency of energy transfer than that with glutaraldehyde conjugate.

Characterization of the artificially covalent conjugate of B-phycoerythrin and R-phycocyanin and the phycobilisome from Porphyridium cruentum

B-phycoerythrin (BPE) and R-phycocyanin (RPC) were purified from Porphyridium cruentum by Sephadex G-200 chromatography, then the BPE was attached covalently to the RPC by reacting their amino groups to form the artificially covalent BPE-RPC conjugate in which the excitation energy can transfer from the BPE to the RPC with low efficiency. Meanwhile, the intact phycobilisome (PBS) consisting of BPE, RPC, APC and L-CM was isolated and purified from Porphyridium cruentum, and the purified PBS was found to keep intact if the solution contains sucrose. Comparison of spectroscopic properties between the purified PBS and the BPE-RPC conjugate suggests that the BPE-RPC conjugate is much more stable than the purified PBS. The construction of BPE-RPC conjugate with low efficiency of the excitation energy transfer may be useful for preparing phycobiliprotein probes. (C) 2002 Elsevier Science Ireland Ltd. All rights reserved.

Geophysical signatures associated with fluid flow and gas hydrate occurrence in a tectonically quiescent sequence, Qiongdongnan Basin, South China Sea

Interpretation of high-resolution two-dimensional (2D) and three-dimensional (3D) seismic data collected in the Qiongdongnan Basin, South China Sea reveals the presence of polygonal faults, pockmarks, gas chimneys and slope failure in strata of Pliocene and younger age. The gas chimneys are characterized by low-amplitude reflections, acoustic turbidity and low P-wave velocity indicating fluid expulsion pathways. Coherence time slices show that the polygonal faults are restricted to sediments with moderate-amplitude, continuous reflections. Gas hydrates are identified in seismic data by the presence of bottom simulating reflectors (BSRs), which have high amplitude, reverse polarity and are subparallel to seafloor. Mud diapirism and mounded structures have variable geometry and a great diversity regarding the origin of the fluid and the parent beds. The gas chimneys, mud diapirism, polygonal faults and a seismic facies-change facilitate the upward migration of thermogenic fluids from underlying sediments. Fluids can be temporarily trapped below the gas hydrate stability zone, but fluid advection may cause gas hydrate dissociation and affect the thickness of gas hydrate zone. The fluid accumulation leads to the generation of excess pore fluids that release along faults, forming pockmarks and mud volcanoes on the seafloor. These features are indicators of fluid flow in a tectonically-quiescent sequence, Qiongdongnan Basin. Geofluids (2010) 10, 351-368.

Seismic characteristics of a reef carbonate reservoir and implications for hydrocarbon exploration in deepwater of the Qiongdongnan Basin, northern South China Sea

Our analysis of approximately 40,000 km of multichannel 2-D seismic data, reef oil-field seismic data, and data from several boreholes led to the identification of two areas of reef carbonate reservoirs in deepwater areas (water depth >= 500 in) of the Qiongdongnan Basin (QDNB), northern South China Sea. High-resolution sequence stratigraphic analysis revealed that the transgressive and highstand system tracts of the mid-Miocene Meishan Formation in the Beijiao and Ledong-Lingshui Depressions developed reef carbonates. The seismic features of the reef carbonates in these two areas include chaotic bedding, intermittent internal reflections, chaotic or blank reflections, mounded reflections, and apparent amplitude anomalies, similar to the seismic characteristics of the LH11-1 reef reservoir in the Dongsha Uplift and Island Reef of the Salawati Basin, Indonesia, which house large oil fields. The impedance values of reefs in the Beijiao and Ledong-Lingshui Depressions are 8000-9000 g/cc x m/s. Impedance sections reveal that the impedance of the LH11-1 reef reservoir in the northern South China Sea is 800010000 g/cc x m/s, whereas that of pure limestone in BD23-1-1 is > 10000 g/cc x m/s. The mid-Miocene paleogeography of the Beijiao Depression was dominated by offshore and neritic environments, with only part of the southern Beijiao uplift emergent at that time. The input of terrigenous sediments was relatively minor in this area, meaning that terrigenous source areas were insignificant in terms of the Beijiao Depression: reef carbonates were probably widely distributed throughout the depression, as with the Ledong-Lingshui Depression. The combined geological and geophysical data indicate that shelf margin atolls were well developed in the Beijiao Depression, as in the Ledong-Lingshui Depression where small-scale patch or pinnacle reefs developed. These reef carbonates are promising reservoirs, representing important targets for deepwater hydrocarbon exploration. (C) 2008 Elsevier Ltd. All rights reserved.