Statistical study of a novel launch scheme for highperformance electronic-equalized multimode-fiber links

A novel launch scheme is proposed for multimode-fiber (MMF) links. Enhanced performance in 10 Gb/s MMF links using electronic equalization is demonstrated by statistical analysis of installed-base fiber and an experimental investigation. © 2007 Optical Society of America.

Comprehensive statistical investigation of SCM-based transmission over 300 m of FDDI-grade multimode fiber

Rigorous statistical analysis is applied for the first time to identify optimal launch conditions and carrier frequencies for SCM transmission over worst-case MMF. The feasibility of multichannel schemes for 10 Gb/s over 300 m is demonstrated. © 2005 Optical Society of America.

Comprehensive statistical investigation of SCM-based transmission over 300 m of FDDI-grade multimode fiber

Rigorous statistical analysis is applied for the first time to identify optimal launch conditions and carrier frequencies for SCM transmission over worst-case MMF. The feasibility of multichannel schemes for 10 Gb/s over 300 m is demonstrated. © 2005 Optical Society of America.

Use of the aquatic protozoa to formulate a community biotic index for an urban water system

Protozoan were collected from 16 stations in water system of Changde City (China) using the PFU method. Sampling programs were conduced on a yearly basis, with seasonal frequency at diverse sites in the water system and 488 species of protozoa was identified. At the same time, Water sampling from these stations was conducted and various water chemical parameters, including DO, COD, BOD5, NH3, TP, and Volatile Phenol, were analyzed. The aim of the research was, on one hand, using chemical method to take an investigation to the water pollution status of Changde City; on the other hand, using protozoan to make an evaluation to the water quality. With the chemical water parameters and protozoa data, a biotic index was derived for the investigated region. The species pollution value (SPV) of 469 protozoa species was established, and the community pollution value (CPV) calculated from SPV was used to evaluate water quality. The method of the biotic index was tested and the result showed that CPV calculated from SPV had a close correlation with the degree of water pollution (p < 0.00001). This indicated that the method of the biotic index is reliable. The water quality degrees divided by CPV were suggested. (c) 2004 Elsevier B.V. All rights reserved.

Development of a biotic index using the correlation of protozoan communities with chemical water quality

A method of comparing data on protozoan communities with chemical parameters is presented. Using data from an extensive survey of the River Hanjiang in China, each species of protozoa has been given a species pollution value (SPV) related to its occurrence in waters with different degrees of pollution. A comprehensive chemical index is calculated for each site based on water quality standards for eight chemical parameters. The index is calculated from the relationship between the observed levels of each chemical at a site, compared with the limits of the drinking water quality standards of the People's Republic of China. From the distribution of each species at sites with differing chemical index values, a SPV is calculated. The SPV for each species is obtained by summing the logarithmic value of 10 times the chemical pollution divided by the number of chemical parameters, then divided by the stations where the species occurs. The community pollution value (CPV), which is the average SPVs of all protozoa at a site, is used to evaluate water quality. The CPV has been shown to have a close correlation with the degree of water pollution. It is not necessary for all the protozoa in a sample to have SPVs listed in this paper, provided at least 56% of the protozoa in a sample have an SPV value, the CPV will be applicable.

Application and validation of a new biotic index using data from several water systems

Protozoans of Lake Donghu were collected from five stations using the PFU method. The sampling was conducted for one year and two times a month. The aim of this research was to test the applicability of a new protozoa biotic index, species pollution value (SPV) and community pollution value (CPV), established by the authors using data from the River Hanjiang. Each station's CPV was calculated from the SPV and the correlation analysis between the CPV and the comprehensive chemical index of stations I, II, III showed a significant correlation between them. The pollution status of the five stations was correctly evaluated by the CPV. These results suggested that the biotic index could be applied in water systems other than the River Hanjiang. The SPV of some protozoa species in Lake Donghu, not observed in the River Hanjiang were established. In order to further test the applicability of the biotic index, protozoan and chemistry data from the Rivers Torrente Stirone and Parma of Italy were used. The results showed that the CPV for the two rivers had a close relationship with the chemical water quality, which indicated that the biotic index could be applied in other parts of the world for the monitoring and estimating of water quality. Since the results of testing and verifying the biotic index in some other water systems in China were also satisfactory, this indicated that the biotic index has an extensive suitability for freshwater ecosystems. As long as more than 50% of the species in a sample have a SPV, the CPV calculated from the SPV is reliable for monitoring and evaluating water quality.

A ridge width varied two-section index-coupled DFB self-pulsation laser with a wide continuously tunable frequency range

A 1.55 mu m InGaAsP-InP index-coupled two-section DFB self-pulsation laser (SPL) with a varied ridge width has been fabricated. A record wide self-pulsation tuning range above 450 GHz has been achieved for this index-coupled DFB SPL. Furthermore, frequency locking to an optically injected modulated signal is successfully demonstrated.

Fabrication and performance of an index-coupled DFB laser with sampled grating

An index-coupled DFB laser with a sampled grating has been designed and fabricated. The key concept of the approaches is to utilize the +1st-order reflection of the sampled grating for laser operation, and use a conventional holographic exposure combined with the usual photolithography to form the sampled grating. The typical threshold current of the sampled grating DFB laser is 25 mA, and the optical output is about 10 mW at the injected current of 100 mA. The lasing wavelength of the device is 1.5314 mu m, which is the +1st-order peak of the sampled grating.

Measurement of chirp parameter and modulation index of a semiconductor laser based on optical spectrum analysis

A novel and simple method for measuring the chirp parameter, frequency, and intensity modulation indexes of directly modulated lasers is proposed in a small-signal modulation scheme. A graphical approach is presented. An analytical solution to the measurement of low chirp parameters is also given. The measured results agree well with those obtained using the conventional methods.

A highly efficient beam propagation method for modeling step-index waveguides with tilt interface

Based on a new finite-difference scheme and Runge-Kutta method together with transparent boundary conditions (TBCs), a novel beam propagation method to model step-index waveguides with tilt interfaces is presented. The modified scheme provides an precies description of the tilt interface of the nonrectangular waveguide structure, showing a much better efficiency and accuracy comparing with the previously presented formulas.

New finite-difference scheme for simulations of step-index waveguides with tilt interfaces

A new finite-difference scheme is presented for the second derivative of a semivectorial field in a step-index optical waveguide with tilt interfaces. The present scheme provides an accurate description of the tilt interface of the nonrectangular structure. Comparison with previously presented formulas shows the effectiveness of the present scheme.

Statistical investigation on morphology development of gallium nitride in initial growth stage

Morphology of Gallium Nitride (GaN) in initial growth stage was observed with atomic force microscopy (AFM) and scanning electron microscopy (SEM), It was found that the epilayer developed from islands to coalesced film. Statistics based on AFM observation was carried out to investigate the morphology characteristics. It was found that the evolution of height distribution could be used to describe morphology development. Statistics also clearly revealed variation of top-face growth rate among islands. Indium-doping effect on morphology development was also statistically studied. The roughening and smoothing behavior in morphology development was explained. (C) 2002 Elsevier Science B.V. All rights reserved.

Structural and optical characterization of InAs nanostructures grown on (001) and high index InP substrates

The effects of InP substrate orientations on self-assembled InAs quantum dots (QDs) have been investigated by molecular beam epitaxy (MBE). A comparison between atomic force microscopy (AFM) and photoluminescence (PL) spectra shows that a high density of smaller InAs islands can be obtained by using such high index substrates. On the other hand, by introducing a lattice-matched underlying In0.52Al0.24Ga0.24As layer, the InAs QDs can be much more uniform in size and have a great improvement in PL properties. More importantly, 1.55-mu m luminescence at room temperature (RT) can be realized in InAs QDs deposited on (001) InP substrate with underlying In0.52Al0.24Ga0.24As layer. (C) 2000 Elsevier Science B.V. All rights reserved.

Refractive index dispersion measurement on nonlinear optical polymer using V-prism refractometer

By using V-prism refractometer, the refractive indices of a polyetherketone (PEK-c) guest-host polymer system were measured with the polymer in solutions. The Lorenz-Lorentz local field formalism was used in the calculation of the refractive indices of the polymers from the measured indices of the polymer solutions and the pure solvent by using V-prism refractometer. The refractive index dispersions of the polymers were obtained by fitting the measured indices of the polymers to Sellmeyer equation. The method allows for an accuracy in index of 0.7% in the determination of the polymer indices. In addition, a large difference between the indices of the polymer and the solvent, and a higher polymer volume fraction in the measured polymer solution are favorable for a high accuracy. (C) 2000 Elsevier Science Ltd. All rights reserved.

Fabrication of InGaAs quantum dots with an underlying InGaAlAs layer on GaAs(100) and high index substrates by molecular beam epitaxy

In this paper, InGaAs quantum dots with an adjusting InGaAlAs layer underneath are grown on (n 1 1)A/B (n = 2-5) and the reference (1 0 0) substrates by molecular beam epitaxy. Small and dense InGaAs quantum dots are formed on (1 0 0) and (n 1 1)B substrates. A comparative study by atomic force microscopy shows that the alignment and uniformity for InGaAs quantum dots are greatly improved on(5 1 1)B but deteriorated on (3 1 1)B surface, demonstrating the great influence of the buried InGaAlAs layer. There is an increase in photoluminescence intensity and a decrease in the full-width at half-maximum when n varies from 2 to 5. Quantum dots formed on (3 1 1)A and (5 1 1)A surfaces are large and random in distribution, and no emission from these dots can be detected. (C) 1999 Elsevier Science B.V. All rights reserved.